Electrical and Computer Engineering Commons^™

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Adaptive Local And Global Synchronization And Phase Control Of Inferior Olive Neurons (Ions), Srujan Kumar Chalike

UNLV Theses, Dissertations, Professional Papers, and Capstones

Clusters of inferior olive neurons (IONs) in the olive-cerebellar system play an important role in providing synchronized motor control signals for the activation of large number of muscles. However, the dynamics of IONs are highly nonlinear and the system parameters are assumed to be unknowm. The IONs evolving from arbitrary initial conditions are not synchronized. However the application of IONs for control of BAUV's requires that IONs oscillate in unison. The objective is to design control laws such that the controlled ION tracks the trajectories of the reference ION. The two control laws are derived based on tuning functions adaptive …

Fault Detection System For Solar Tracking Applications, Hareen Sekhar Illa

Electrical & Computer Engineering Theses & Dissertations

Oil, coal and natural gas reserves are being depleted faster than forecasted due to continued increase in demand for energy sources. We need, therefore, to develop renewable energy sources, such as solar, wind, biomass, geothermal, hydro power and tidal energy. In spite of having very high potential, harvesting solar energy has been a challenge because of the relatively low efficiency of solar cells. In the past few years different methods have been developed to increase the efficiency of the photovoltaic (PV) system: (I) improve the efficiency of solar cells (ill use a solar tracking system to increase the received solar …

Control System For Glucose Detector System, David Smith

Electrical Engineering

In this paper I design and test on a prove of concept level a control/timing circuit for a blood glucose detector built in a previous senior project. The specifications of the design given are to properly power the detector with a low power source. The design is completed on a transistor level basis using Cadence Virtuoso Software. The system is design from the ground up; designing, building, and testing smaller circuits first then combined into increasingly larger circuits till the completed circuit is finished. The design used to based off of the 555 Timer and uses differential pairs, CMOS designed …

Frg Turbojet, Tyler Vitti

Computer Engineering

Members of the Cal Poly SLO campus club FRG work together with students of several different disciplines to build a functional turbojet engine. Engineering approaches include design, fabrication, testing, and computer sensing, control, and integration. The goal of the project is to produce a running turbojet engine monitored and controlled by embedded hardware and specialized PC software. This project is to be used by later groups for further research and development.

Independent Moisture-Sensitive Automatic Watering System, Jessica Sherbon

Electrical Engineering

With the availability of home improvement supplies, plant owners can quickly and easily set up an automatic system that waters their gardens based on a specified schedule. However, most of these systems require an electric outlet or water faucet making them unusable in locations where installed water and power lines do not exist, such as apartment balconies. This project defines a small-scale automated watering system that runs independently of installed water and power lines. The system takes water from a reservoir, such as a tank or bucket, and supplies that water to individual plants via a drip system. The design …

A Proposed Control Solution For The Cal Poly Wind Energy Capture System, Kent R. Burnett

Master's Theses

The focus of this thesis is to research, analyze, and design a reliable and economical control system for the Cal Poly Wind Energy Capture System (WECS). A dynamic permanent magnet generator model is adopted from [1] and [2] and combined with an existing wind turbine model to create a non-linear time varying model in MATLAB. The model is then used to analyze potentially harmful electrical disturbances, and to define safe operating limits for the WECS. An optimal operating point controller utilizing a PID speed loop is designed with combined optimization criteria and the final controller design …

Monitoring And Regression Based Modelling Of End Winding Vibration In Large Synchronous Generators., David Shally

Masters

This research project was set up to monitor, on an ongoing basis, the condition of the end windings and their support structures of a 288 MVA 2-pole synchronous generator with a known end winding vibration problem Excessive vibration at the end windings was caused by the natural frequencies of individual end bars (local) and of the entire end winding structure (global) being at or close to the magnetic forcing frequency of 100 Hz. Resonant vibration such as this has been a cause of major failures in machines of the same type in the past, resulting in significant down time ranging …

A Robust Decentralized Load Frequency Controller For Interconnected Power Systems, Lili Dong, Yao Zhang, Zhiqiang Gao

Electrical and Computer Engineering Faculty Publications

A novel design of a robust decentralized load frequency control (LFC) algorithm is proposed for an inter-connected three-area power system, for the purpose of regulating area control error (ACE) in the presence of system uncertainties and external disturbances. The design is based on the concept of active disturbance rejection control (ADRC). Estimating and mitigating the total effect of various uncertainties in real time, ADRC is particularly effective against a wide range of parameter variations, model uncertainties, and large disturbances. Furthermore, with only two tuning parameters, the controller provides a simple and easy-to-use solution to complex engineering problems in practice. Here, …

A Consumer Level Simulation Model For Demand Response Analysis On Smart Grid, Sungchul Lee, Yoohwan Kim

College of Engineering: Graduate Celebration Programs

With the growing awareness of the need for Smart Grid, various countries are taking initiatives for developing Smart Grid.

However, there is limited research on utilizing Smart Grid for Demand-Response (DR).

This study advances the current system of DR by creating a Smart Grid Simulator that allows an intuitive demand response analysis.

The simulator demonstrates that substantial amount of electric power can be reduced efficiently by selective demand control over Smart Grid.

The graphical interface allows generating the electrical usage data and displays both individual and aggregate usage data over time.

This research employs U.S. census data for accurate estimate …

Improving Manufacturing Processes Through Energy Monitoring, Andrew Grzelak

Purdue Polytechnic Masters Theses

Energy efficiency and sustainability are very popular topics in the current field of manufacturing. With the increase in use of automation technology as well as the recent growth in the area of energy management, there is much focus on the overall improvement of manufacturing processes. For this research a project was completed to create a system that could improve both process efficiency as well as decrease energy consumption. By taking a look at the machine level energy consumption of an automated piece of manufacturing equipment, by eliminating waste in process, both energy efficiency and operational efficiency can be improved.

Using …

Smart Home Prototype, Logistics & Planning, David G. Guzman^, Virgilio Gonzalez*

COURI Symposium Abstracts, Spring 2012

No abstract provided.

Fadec Advances Allow Better Engine Performance, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

A Teaching Practice Review Of The Use Of Multiple-Choice Questions For Formative And Summative Assessment Of Student Work On Advanced Undergraduate And Postgraduate Modules In Engineering, Aidan O'Dwyer

Articles

This paper reflects on, reports on and evaluates the use of multiple-choice questions, in both formative and summative assessment modes, on control engineering modules taken by advanced undergraduate and postgraduate engineering students, over four academic years. The material covered by the modules is analytical in nature. The rationale for examining the assessment strategy was the poor performance by students in a closed book traditional terminal examination on one of the advanced undergraduate modules over some years. The change in assessment strategy has improved student learning, as measured by assessment data; student feedback on the assessment methods is broadly positive. The …

A Review Of Some Subtleties Of Practical Relevance, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper reviews some subtleties in time-delay systems of neutral type that are believed to be of particular relevance in practice. Both traditional formulation and the coupled differential-difference equation formulation are used. The discontinuity of the spectrum as a function of delays is discussed. Conditions to guarantee stability under small parameter variations are given. A number of subjects that have been discussed in the literature, often using different methods, are reviewed to illustrate some fundamental concepts. These include systems with small delays, the sensitivity of Smith predictor to small delay mismatch, and the discrete implementation of distributed-delay feedback control. The …

Root Locus Techniques With Nonlinear Gain Parameterization, Brandon Wellman

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents rules that characterize the root locus for polynomials that are nonlinear in the root-locus parameter k. Classical root locus applies to polynomials that are affine in k. In contrast, this thesis considers polynomials that are quadratic or cubic in k. In particular, we focus on constructing the root locus for linear feedback control systems, where the closed-loop denominator polynomial is quadratic or cubic in k. First, we present quadratic root-locus rules for a controller class that yields a closed-loop denominator polynomial that is quadratic in k. Next, we develop cubic root-locus rules …

An Adaptive Utility Interactive Photovoltaic System Based On A Flexible Switch Matrix To Optimize Performance In Real-Time, Mahmoud Alahmad, Mohamed Amer Chaaban, Siu Kit Lau, Jonathan Shi, Jill Neal

Durham School of Architectural Engineering and Construction: Faculty Publications

Reconfigurable architectures are of great interest to system designers to improve the system’s operation and efficiency. In this paper, we propose an adaptive utility interactive photovoltaic (PV) system based on a novel Flexible Switch array Matrix topology. This proposed system maximizes the generated power in real-time in response to operational conditions such as shading, soiling, mismatches, and module failure among others. The proposed system is a compromise in the utilization of power conditioning equipment to maximize energy capture and system efficiency. Simulation results demonstrate an average 13% improvement in efficiency when compared with the central inverter topology performance. A prototype …

Feedback Control For Electron Beam Lithography, Yugu Yang

Theses and Dissertations--Electrical and Computer Engineering

Scanning-electron-beam lithography (SEBL) is the primary technology to generate arbitrary features at the nano-scale. However, pattern placement accuracy still remains poor compared to its resolution due to the open-loop nature of SEBL systems. Vibration, stray electromagnetic fields, deflection distortion and hysteresis, substrate charging, and other factors prevent the electron-beam from reaching its target position and one has no way to determine the actual beam position during patterning with conventional systems. To improve the pattern placement accuracy, spatial-phase-locked electron-beam lithography (SPLEBL) provides feedback control of electron-beam position by monitoring the secondary electron signal from electron-transparent fiducial grids on the substrate. While …

Improvements In Genetic Approach To Pole Placement In Linear State Space Systems Through Island Approach Pga With Orthogonal Mutation Vectors, Arnold Cassell

UNF Graduate Theses and Dissertations

This thesis describes a genetic approach for shaping the dynamic responses of linear state space systems through pole placement. This paper makes further comparisons between this approach and an island approach parallel genetic algorithm (PGA) which incorporates orthogonal mutation vectors to increase sub-population specialization and decrease convergence time.

Both approaches generate a gain vector K. The vector K is used in state feedback for altering the poles of the system so as to meet step response requirements such as settling time and percent overshoot. To obtain the gain vector K by the proposed genetic approaches, a pair of ideal, desired …

Dynamic Test Scheduling In Hardware-In-The-Loop Simulation Of Commercial Vehicles, Tenil Cletus

Master's Theses

Modern day commercial vehicles are controlled by various Electronic Control Units (ECU). They are not only tested as single units, but also by networking them in Controlled Area Network bus (CAN) to form a complete electrical control system. This is achieved using Hardware In the Loop (HIL) Integration Lab. In HIL, the electrical system is connected to a real time mathematical model of the vehicle plus it’s environment so as to form a loop.

Testing functionality of the electrical system begins by defining functional tests. An example would be testing cruise control activation. Executing each test is made possible by …

Integration Of Upqc For Power Quality Improvement In Distributed Generation Network – A Review, Shafiuzzaman Khan Khadem, Malabika Basu, Michael Conlon

Conference Papers

In this paper a technical review of the integration of a Unified Power Quality Conditioner (UPQC) in a distributed generation network is presented. Although the primary task of UPQC is to minimize grid voltage and load current disturbances along with reactive and harmonic power compensation, additional functionalities such as compensation of voltage interruption and active power transfer to the load and grid have also been identified. Connection methodologies with their advantages and disadvantages are also described. Recent improvements in capacity expansion techniques and future trends for the application of UPQC in distributed modes are also identified.

Highly Efficient Maximum Power Point Tracking Using A Quasi-Double-Boost Dc/Dc Converter For Photovoltaic Systems, Christopher J. Lohmeier

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Solar photovoltaic (PV) panels are a great source of renewable energy generation. The biggest problem with solar systems is relatively low efficiency and high cost. This work hopes to alleviate this problem by using novel power electronic converter and control designs. An electronic DC/DC converter, called “Quasi-Double-Boost DC/DC Converter,” is designed for a Solar PV system. A Maximum Power Point Tracking (MTTP) algorithm is implemented through this converter. This algorithm allows the PV system to work at its highest efficiency. Different current sensing and sensorless technologies used with the converter for the MPPT algorithm are offered and tested. Design aspects …

Sensing And Transmission Strategies In Wireless Cognitive Radio Systems, Babak Abbasi Bastami

UNLV Theses, Dissertations, Professional Papers, and Capstones

The main challenge in any cognitive radio system is to maximize secondary users throughput while limiting interference imposed on licensed users. In this regard, finding the optimal sensing and transmission timing strategies and accurate sensing techniques are of great importance in a cognitive radio network.

In this thesis, we study a sensing-transmission scheme for secondary user in a cognitive radio system where the secondary user senses every primary channel independently and transmits a signal for a fixed duration if it finds the channel empty and stays idle for another fixed duration if it senses the channel busy. We obtain optimal …

A Study Of A Novel Modular Variable Geometry Frame Arranged As A Robotic Surface, Christopher James Salisbury

UNLV Theses, Dissertations, Professional Papers, and Capstones

The novel concept of a "variable geometry frame" is introduced and explored through a three-dimensional robotic surface which is devised and implemented using triangular modules. The link design is optimized using surplus motor dimensions as firm constraints, and round numbers for further arbitrary constraints. Each module is connected by a passive six-bar mechanism that mimics the constraints of a spherical joint at each triangle intersection. A three dimensional inkjet printer is used to create a six-module prototype designed around surplus stepper motors powered by an old computer power supply as a proof-of-concept example.

The finite element method is applied to …

Super-Resolution For Imagery From Integrated Microgrid Polarimeters, Russell C. Hardie, Daniel A. Lemaster, Bradley M. Ratliff

Electrical and Computer Engineering Faculty Publications

Imagery from microgrid polarimeters is obtained by using a mosaic of pixel-wise micropolarizers on a focal plane array (FPA). Each distinct polarization image is obtained by subsampling the full FPA image. Thus, the effective pixel pitch for each polarization channel is increased and the sampling frequency is decreased. As a result, aliasing artifacts from such undersampling can corrupt the true polarization content of the scene. Here we present the first multi-channel multi-frame super-resolution (SR) algorithms designed specifically for the problem of image restoration in microgrid polarization imagers. These SR algorithms can be used to address aliasing and other degradations, without …

The Tracking Performance Of Distributed Recoverable Flight Control Systems Subject To High Intensity Radiated Fields, Rui Wang

Electrical & Computer Engineering Theses & Dissertations

It is known that high intensity radiated fields (HIRF) can produce upsets in digital electronics, and thereby degrade the performance of digital flight control systems. Such upsets, either from natural or man-made sources, can change data values on digital buses and memory and affect CPU instruction execution. HIRF environments are also known to trigger common-mode faults, affecting nearly-simultaneously multiple fault containment regions, and hence reducing the benefits of n-modular redundancy and other fault-tolerant computing techniques. Thus, it is important to develop models which describe the integration of the embedded digital system, where the control law is implemented, as well …

On Active Disturbance Rejection Based Control Design For Supercomputing Rf Cavities, John Vincent, Dan Morris, Nathan Usher, Zhiqiang Gao, Shen Zhao, Achille Nicoletti, Qinling Zheng

Electrical and Computer Engineering Faculty Publications

Superconducting RF (SRF) cavities are key components of modern linear particle accelerators. The National Superconducting Cyclotron Laboratory (NSCL) is building a 3 MeV/u re-accelerator (ReA3) using SRF cavities. Lightly loaded SRF cavities have very small bandwidths (high Q) making them very sensitive to mechanical perturbations whether external or self-induced. Additionally, some cavity types exhibit mechanical responses to perturbations that lead to high-order non-stationary transfer functions resulting in very complex control problems. A control system that can adapt to the changing perturbing conditions and transfer functions of these systems would be ideal. This paper describes the application of a control …

Autonomous Crash Avoidance System, Brian Ujiie, Gordon Woods, Joshua Miller

Mechanical Engineering

No abstract provided.

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …