Robotics Commons^™

Mobius: An Omnidirectional Robotic Platform And Software Architecture For Network Teleoperation, Samuel Aaron Miller

Electrical & Computer Engineering Theses & Dissertations

The following thesis presents the results of a project to develop and test an omnidirectional robotic system (hardware and software) at NASA Langley Research Center's Robotics and Intelligent Machines Lab. The impetus for the project was the unique capabilities of omnidirectional systems. Some of the many potential benefits these systems have include improved material-handling capabilities in constrained environments (such as might be found in extraterrestrial manned habitats), efficient camera-based vehicle teleoperation, and simplified route planning for autonomous robot operations.

The project's focus was to design, build, and test a system that used Mecanum wheels to achieve omnidirectional motion. In addition …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #1, Jamil M. Renno, Georg F. Mauer

Fuels Campaign (TRP)

A Hot Cell robotic assembly: Pick and place dynamic simulation, including feedback control with Matlab, was developed for dispersion fuel manufacture.

The deployment of remote manufacturing of transmuter fuel is a necessity for the transmutation applications. In the reporting period, a virtual hot cell for the manufacturing of dispersion fuel was designed using MSC.visualNastran^©, ProEngineer^© and MATLAB^©. Atypical events were successfully simulated. Relevant physical quantities arising during such events were monitored as well.

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project was to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models were developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment were also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Transmuter Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

• Project Objective: examine autonomous robotic fuel fabrication processes with regard to hot cell and equipment design, operations, and costs.

• Fabrication processes for different fuel types differ in terms of equipment types, throughput, and cost.

• Design options are restricted by the requirement to employ only radiation-hardened machinery and components

• Benefit to Department of Energy: decision support for the selection of the most suitable manufacturing process.

Trends. War On Personality And Personality And War: Comments On Nass And Lee (2002), Ibpp Editor

International Bulletin of Political Psychology

This Trends article discusses another article – Identity and deconstruction, by Clifford Nass and Kwan Min Yee – published in volume 3 (2002) of Archives of Psychiatry & Psychotherapy in which the authors demonstrate that people reliably attribute personality characteristics to computer-synthesized speech, exploring the ramifications in a political psychological context.

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Comparison Of Two Distributed Fuzzy Logic Controllers For Flexible-Link Manipulators, Linda Z. Shi, Mohamed Trabia

Mechanical Engineering Faculty Presentations

The paper suggests that fuzzy logic controllers present a computationally efficient and robust alternative to conventional controllers. The paper presents two possible structures for the distributed fuzzy logic controller of a single-link flexible manipulator. A linear quadratic regulator method is used to prove the effectiveness of fuzzy logic controllers.

Robust Course-Boundary Extraction Algorithms For Autonomous Vehicles, Chris Roman, Charles Reinholtz

Graduate School of Oceanography Faculty Publications

Practical autonomous robotic vehicles require dependable methods for accurately identifying course or roadway boundaries. The authors have developed a method to reliably extract the boundary line using simple dynamic thresholding, noise filtering, and blob removal. This article describes their efforts to apply this procedure in developing an autonomous vehicle.

Matching Points To Lines: Sonar-Based Localization For The Psubot, Kevin Blythe Stanton

Dissertations and Theses

The PSUBOT (pronounced pea-es-you-bought) is an autonomous wheelchair robot for persons with certain disabilities. Its use of voice recognition and autonomous navigation enable it to carry out high level commands with little or no user assistance. We first describe the goals, constraints, and capabilities of the overall system including path planning and obstacle avoidance. We then focus on localization-the ability of the robot to locate itself in space. Odometry, a compass, and an algorithm which matches points to lines are each employed to accomplish this task. The matching algorithm (which matches "points" to "lines") is the main contribution to this …

Impacts Of Industrial Robotics: Potential Effects On Labor And Costs Within The Metalworking Industries, Steven M. Miller

Research Collection School Of Computing and Information Systems

According to leading expert opinion, industrial robots are among the most important innovations of recent decades. Yet there is very considerable uncertainty (and disagreement) as to the rate at which the use of robots will spread and what their effects on employment, costs, and market structure will be. As stressed in 1983 by Congress’s Office of Technology Assessment: “A central question for an analysis of the social and economic impacts of programmable automation is whether programmable automation is likely to spread especially rapidly among firms and industries, and why.” The author analyzes the job displacement effects of industrial robots, as …

Impact Of Automation On Process Control Decision-Making, Steven M. Miller, Susan R. Bereiter

Research Collection School Of Computing and Information Systems

This paper investigates changes in the process control of a vehicle assembly plant which had been modernized from a principally manual procedure to one that uses programmable automation extensively. Process control is defined as the information flow and decision-making required to perform basic process operations. We investigate the effects of implementing a computer-integrated production system on the amount and types of process control decision-making and on the distribution of process control decision-making between humans and machines. After automation, the emphasis on decisions regarding product quality specifications increased and the emphasis on decisions related to flexibility in handling a variety of …

Impacts Of Robotics And Flexible Manufacturing Technologies On Manufacturing Costs And Employment, Steven M. Miller

Research Collection School Of Computing and Information Systems

The issues analyzed in this paper are the extent to which unit costs and production labor requirements might be reduced in manufacturing industries if there is more widespread use of industrial robots and flexible systems. The analysis is reported in detail in Miller (1983). These issues are analyzed from two different perspectives. The technological focus of the first perspective is narrowly confined to the use of robotic manipulators. It is assumed that robotic manipulators will be “retrofitted” into existing production facilities without making major changes in the organization of production within the factory, other than modifying individual work stations so …

Robotic Realities: Near Term Prospects And Problems, Robert U. Ayres, Steven M. Miller

Research Collection School Of Computing and Information Systems

Industrial robots are automation, but with a difference. Other machine tools are extensions of human capabilities, while robots are seen mainly as substitutes for human workers. Robots will find most of their industrial applications during the next decade or two in the metal-working sectors, where they will begin to displace semiskilled machine operatives in medium to large batch production operations. They cannot substitute for skilled machinists or other workers doing nonroutine jobs, or specialized, dedicated hard automation used in mass production. The current generation of robots, lacking sensory data processing and interpretation capabilities, can potentially replace up to 1.3 million …

Robotics And The Conservation Of Human Resources, Robert U. Ayres, Steven M. Miller

Research Collection School Of Computing and Information Systems

Due to rapid expansion in the field of robotics, policy issues have arisen in regard to developing human skills to deal with the new technology and to deal with the obsolescent human skills which are the inevitable result of this growth pattern. Industrialists, educators, union leaders, and government officials must work cooperatively to insure that the coming changes are made with minimum disruption. Improved training methods and courses have to be developed for the skills needed to control, manage and supervise the new machines. Some of the ways in which this can be accomplished are through offering financial incentives for …