Computer Engineering Commons^™

Digital Control Board For Phased Array Antenna Beam Steering In Adaptive Communication Applications, Mayur Bansal

Master's Theses

The application of adaptive communication techniques for mobile communications has attracted considerable interest in the last decade. One example of these techniques is spatial filtering through planar antenna array beam forming.

This thesis describes the development of a digital system that adaptively controls a phased array antenna. The radiating structure of the phased antenna array is tetrahedral-shaped and contains four antenna elements on each of its three faces. The overall system comprises of a digital control board with an external computer interface, an RF control board, and the phased antenna array. The RF controls the main lobe direction on the …

Calculation Of Magnet Losses In Concentrated-Winding Permanent-Magnet Synchronous Machines Using A Computationally Efficient Finite-Element Method, Peng Zhang, Gennadi Y. Sizov, Jiangbiao He, Dan M. Ionel, Nabeel Demerdash

Electrical and Computer Engineering Faculty Research and Publications

The proposed hybrid method combines computationally efficient finite-element analysis (CE-FEA) with a new analytical formulation for eddy-current losses in the permanent magnets (PMs) of sine-wave current-regulated brushless synchronous motors. The CE-FEA only employs a reduced set of magnetostatic solutions yielding substantial reductions in the computational time, as compared with the conventional FEA. The 3-D end effects and the effect of pulsewidth-modulation switching harmonics are incorporated in the analytical calculations. The algorithms are applied to two fractional-slot concentrated-winding interior PM motors with different circumferential and axial PM block segmentation arrangements. The method is validated against 2-D and 3-D time-stepping FEA.

An Ant-Based Sensor Measurement Data Gathering System, Bolun Zhang, Dimitrios Peroulis

The Summer Undergraduate Research Fellowship (SURF) Symposium

Large-scale industries involved with a great amount of sensor measurements in their work are facing many challenges in data collection. Sensors are not on the same network; therefore each measurement has to be managed separately. Gathering all the measurement data to one terminal could be difficult. Once a measurement is obtained, it takes significant amount of time to process the data.The approaches our group takes here is to build a giant ANT wireless network that holds all the sensors’ measurements. To be more specific, every sensor has an ANT chip set up on its side. Each ANT chip is as …

Microelectromechanical Systems (Mems) Resistive Heaters As Circuit Protection Devices, Ronald A. Coutu Jr., Scott A. Ostrow

Electrical and Computer Engineering Faculty Research and Publications

With increased opportunities for the exploitation (i.e., reverse engineering) of vulnerable electronic components and systems, circuit protection has become a critical issue. Circuit protection techniques are generally software-based and include cryptography (encryption/decryption), obfuscation of codes, and software guards. Examples of hardware-based circuit protection include protective coatings on integrated circuits, trusted foundries, and macro-sized components that self-destruct, thus destroying critical components. This paper is the first to investigate the use of microelectromechanical systems (MEMS) to provide hardware-based protection of critical electronic components to prevent reverse engineering or other exploitation attempts. Specifically, surface-micromachined polycrystalline silicon to be used as meandering resistive heaters …

Resource-Aware Distributed Particle Filtering For Cluster-Based Object Tracking In Wireless Camera Networks, Kihyun Hong

Open Access Dissertations

The proliferation of miniaturized low-power computing devices, advances in wireless communications, and the availability of inexpensive imaging sensors have enabled the development of wireless camera networks (WCN). In this dissertation, we consider the problem of real-time object tracking with a WCN. Existing object tracking methods designed for multi-camera systems do not take into account the unique constraints of WCNs. Specifically, an effective object tracking system for WCNs must anticipate unreliable network communication, limited memory, and limited computational power in each camera node. In particular, unreliable communication degrades the quality of the visual information shared by the cameras, which ultimately degrades …

Harmonic Generation In Multiresonant Plasma Films, Maria Antonietta Vincenti, Domenico De Ceglia, Joseph W. Haus, Michael Scalora

Electrical and Computer Engineering Faculty Publications

We investigate second- and third-harmonic generation in a slab of material that displays plasma resonances at the pump and its harmonic frequencies. Near-zero refractive indices and local field enhancement can deplete the pump for kW/cm² incident powers, without resorting to other resonant photonic mechanisms. We show that low-threshold, highly efficient nonlinear processes are possible in the presence of losses and phase mismatch in structures that are 10⁴ times shorter than typical nonlinear crystals, for relatively low irradiance values.

Money Laundering Detection Framework To Link The Disparate And Evolving Schemes, Murad Mehmet, Duminda Wijesekera, Miguel F. Buchholtz

Journal of Digital Forensics, Security and Law

Money launderers hide traces of their transactions with the involvement of entities that participate in sophisticated schemes. Money laundering detection requires unraveling concealed connections among multiple but seemingly unrelated human money laundering networks, ties among actors of those schemes, and amounts of funds transferred among those entities. The link among small networks, either financial or social, is the primary factor that facilitates money laundering. Hence, the analysis of relations among money laundering networks is required to present the full structure of complex schemes. We propose a framework that uses sequence matching, case-based analysis, social network analysis, and complex event processing …

Self-Timed Dram Data Interface, Rajesh Nerkar

Dissertations and Theses

A DRAM communicates with a processing unit via two interfaces: a data interface and a command interface. In today's DRAMs, also known as synchronous DRAMs (SDRAMs), both interfaces use a clock to communicate with the processing unit. The clock times the communication between the processing unit and the SDRAM on both the data interface and the command interface.

We propose a self-timed DRAM. The self-timed DRAM introduces more flexibility into the DRAM interface by eliminating the clock. The command interface and the data interface each communicate with the processing unit using a handshake protocol rather than a clock.

This thesis …

Isolation Of High Quality Graphene From Ru By Solution Phase Intercalation, E. Koren, Eli A. Sutter, S. Bliznakov, F. Ivars-Barcelo, P. Sutter

Department of Electrical and Computer Engineering: Faculty Publications

2013 AIP Publishing LLC

A Review Of Micro-Contact Physics For Microelectromechanical Systems (Mems) Metal Contact Switches, Benjamin F. Toller, Ronald A. Coutu Jr., John W. Mcbride

Electrical and Computer Engineering Faculty Research and Publications

Innovations in relevant micro-contact areas are highlighted, these include, design, contact resistance modeling, contact materials, performance and reliability. For each area the basic theory and relevant innovations are explored. A brief comparison of actuation methods is provided to show why electrostatic actuation is most commonly used by radio frequency microelectromechanical systems designers. An examination of the important characteristics of the contact interface such as modeling and material choice is discussed. Micro-contact resistance models based on plastic, elastic-plastic and elastic deformations are reviewed. Much of the modeling for metal contact micro-switches centers around contact area and surface roughness. Surface roughness and …

Nonlinear Dynamics Of Bragg-Domain Acousto-Optic Hybrid Feedback For First-Order Scattering Of Profiled Optical Beams, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

A series of recent studies involving hybrid acousto-optic (AO) scattering in the Bragg domain under first-order feedback have shown the ability of the AO feedback system to encrypt, transmit and decrypt RF information applied via the sound driver. The basic premise of this operation is founded on the chaotic nature of the hybrid Bragg cell under feedback.

Using Meta-Ethnography To Synthesize Research: A Worked Example Of The Relations Between Personality On Software Team Processes, Fabio Q. B. Silva Dr., Shirley S. J. O. Cruz, Tatiana B. Gouveia, Luiz Fernando Capretz

Electrical and Computer Engineering Publications

Context: The increase in the number of qualitative and mixed-methods research published in software engineering has created an opportunity for further knowledge generation through the synthesis of studies with similar aims. This is particularly true in the research on human aspects because the phenomena of interest are often better understood using qualitative research. However, the use of qualitative synthesis methods is not widespread and worked examples of their consistent application in software engineering are needed. Objective: To explore the use of meta-ethnography in the synthesis of empirical studies in software engineering through an example using studies about the relations between …

Passive Mimo Radar Detection, Daniel E. Hack

Theses and Dissertations

Passive multiple-input multiple-output (MIMO) radar is a sensor network comprised of multiple distributed receivers that detects and localizes targets using the emissions from multiple non-cooperative radio frequency transmitters. This dissertation advances the theory of centralized passive MIMO radar (PMR) detection by proposing two novel generalized likelihood ratio test (GLRT) detectors. The first addresses detection in PMR networks without direct-path signals. The second addresses detection in PMR networks with direct-path signals. The probability distributions of both test statistics are investigated using recent results from random matrix theory. Equivalence is established between PMR networks without direct-path signals and passive source localization (PSL) …

Enhancing Electromagnetic Side-Channel Analysis In An Operational Environment, David P. Montminy

Theses and Dissertations

Side-channel attacks exploit the unintentional emissions from cryptographic devices to determine the secret encryption key. This research identifies methods to make attacks demonstrated in an academic environment more operationally relevant. Algebraic cryptanalysis is used to reconcile redundant information extracted from side-channel attacks on the AES key schedule. A novel thresholding technique is used to select key byte guesses for a satisfiability solver resulting in a 97.5% success rate despite failing for 100% of attacks using standard methods. Two techniques are developed to compensate for differences in emissions from training and test devices dramatically improving the effectiveness of cross device template …

Automated Multi-Objective Design Optimization Of Pm Ac Machines Using Computationally Efficient Fea And Differential Evolution, Gennadi Y. Sizov, Peng Zhang, Dan M. Ionel, Nabeel Demerdash, Marius Rosu

Electrical and Computer Engineering Faculty Research and Publications

The design optimization methods described in this paper are employing an ultrafast computationally efficient finite element analysis technique. A minimum number of magnetostatic solutions are used for the analysis, which makes possible the study of thousands of candidate motor designs with typical PC-workstation computational resources. A multi-objective differential evolution algorithm that considers a large number of independent stator and rotor geometric variables and performance criteria, such as average and ripple torque, losses, and efficiency, is used. The optimization method is demonstrated on different permanent magnet (PM) ac synchronous motors in the kilowatt and megawatt power ranges. For the low-power PM …

The Effect Zeolite Addition In Natural Rubber Polypropylene Composite On Mechanical, Structure, And Thermal Characteristics, Nurdin Bukit, Erna Frida

Makara Journal of Technology

This study was conducted to determine the effect of zeolite as filler on mechanical properties, and thermal structure blends of natural rubber and polypropylene (NR/PP). In this study, NR/PP/PP-g-MA blends was filled uncalcined zeolite and calcined zeolite at different weight percent of the 2, 4, and 6%. Samples were characterized to determine the tensile strength, fracture elongation and Young's modulus. Structure of the samples was investigated using XRD method and thermal characteristics were analyzed using DTA/TGA technique. The results obtained for tensile strength showed a significant influence with the addition zeolite of the NR/PP blends at 2% by weight of …

Characteristics Of Vacuum Freeze Drying With Utilization Of Internal Cooling And Condenser Waste Heat For Sublimation, Muhammad Idrus Alhamid, Nasruddin Yusuf, Indra Teuku Meurah Mahlia, Engkos Ahmad Kosasih, Muhamad Yulianto, Rio Ricardi

Makara Journal of Technology

Vacuum freeze drying is an excellent drying method, but it is very energy-intensive because a relatively long drying time is required. This research investigates the utilization of condenser waste heat for sublimation as a way of accelerating the drying rate. In addition, it also investigates the effect of internal cooling combined with vacuum cooling in the pressure reduction process. Jelly fish tentacles were used as the specimen, with different configurations for condenser heat waste and internal cooling valve opening. The results show that heating with condenser heat waste can accelerate the drying rate up to 0.0035 kg/m2.s. In addition, pre-freezing …

A New Experimental Approach To Evaluate Plasma-Induced Damage In Microcantilever, Yuki Nishimori, Shinji Ueki, Masakazu Sugiyama, Seiji Samukawa, Gen Hashiguchi

Makara Journal of Technology

Plasma etching, during micro-fabrication processing is indispensable for fabricating MEMS structures. During the plasma processes, two major matters, charged ions and vacuum–ultraviolet (VUV) irradiation damage, take charge of reliability degradation. The charged ions induce unwanted sidewall etching, generally called as “notching”, which causes degradation in brittle strength. Furthermore, the VUV irradiation gives rise to crystal defects on the etching surface. To overcome the problem, neutral beam etching (NBE), which use neutral particles without the VUV irradiation, has been developed. In order to evaluate the effect of the NBE quantitatively, we measured the resonance property of a micro-cantilever before and after …

Fatigue Life Prediction Of The Keel Structure Of A Tsunami Buoy Using Spectral Fatigue Analysis Method, Angga Yustiawan, Ketut Suastika, Wibowo Harso Nugroho

Makara Journal of Technology

One of the components of the Indonesia Tsunami Early Warning System (InaTEWS) is a surface buoy. The surface buoy is exposed to dynamic and random loadings while operating at sea, particularly due to waves. Because of the cyclic nature of the wave load, this may result in a fatigue damage of the keel structure, which connects the mooring line with the buoy hull. The operating location of the buoy is off the Java South Coast at the coordinate (10.3998 S, 108.3417 E). To determine the stress transfer function, model tests were performed, measuring the buoy motions and the stress at …

The Plasma Electrolysis Phenomenon In A Two-Compartment Reactor For Chlor-Alkali Production, Nelson Saksono, Fakhrian Abqari, Setijo Bismo

Makara Journal of Technology

Chlor-alkali is one of the most important processes in the chemical industry. It produces chlorine and caustic soda, which become the main feedstock of daily products. The aim of this study is to report the phenomenon of plasma electrolysis and how it can be used in chlor-alkali production for more efficient energy consumption. When the plasma is formed, the current fluctuates and gradually declines. Plasma electrolysis begins with the process of electrolysis itself. Due to Joule heating, gas bubbles are formed and a sheath is made on both electrodes, resulting in the plasma field. Plasma electrolysis can be identified by …

Observation Of Photovoltaic Effect And Single-Photon Detection In Nanowire Silicon Pn-Junction, Arief Udhiarto, Sri Purwiyanti, Daniel Moraru, Takeshi Mizuno, Michiharu Tabe

Makara Journal of Technology

We study nanowire silicon pin and pn-junctions at room and low temperature. Photovoltaic effects are observed for both devices at room temperature. At low temperature, nanowire pn-junction devices show their ability to detect single photon. This ability was not been observed for pin devices. Phosphorus-boron dopant cluster in the depletion region is considered to have the main role for single-photon detection capability. Fundamental mechanism of dopant-based single-photon detection in nanowire pn-junction is described in details.

Influences Of Surface Morphology Of Nanostructured Rutile Tio2 Nanorods/Nanoflowers As Photoelectrode On The Performance Of Dye-Sensitized Solar Cell, Mohd Khairul Bin Ahmad, Kenji Murakami

Makara Journal of Technology

Aligned Rutile TiO2 nanorods (r-TNRs) and TiO2 nanoflowers (r-TNFs) were successfully prepared by hydrothermal method. Using hydrochloric acid (HCl) as chelating agent and titanium butoxide (TBOT) as precursor, aligned r-TNRs with r-TNFs were successfully growth onto fluorine-doped tin oxide (FTO) with different morphologies. The influences of surface morphologies to the rutile based Dye-sensitized solar cell (DSC) efficiency are discussed. The highest lightto- electric energy conversion efficiency, 1.80% is achieved using different concentration under simulated solar light illumination of 100 mWcm-2 (1.5 AM).

Improvement In Performance Of Zno Based Dsc Prepared By Spraying Method, Rangga Winantyo, Devinda Liyanage, Kenji Murakami

Makara Journal of Technology

This paper reports the effect of TiCl4 on the performance of ZnO based DSC. ZnO was used due to its stability against photo-corrosion and photochemical properties similar to TiO2. Thin films of nanocrystalline ZnO were deposited on transparent conducting oxide glass using spray method. The ZnO films were treated using TiCl4. The cell’s efficiency was found to be 2.5% with TiCl4 post-treatment and 1.9% without TiCl4 post-treatment.

Determining The Air Gap Length Of An Axial Flux Wound Rotor Synchronous Generator, Abdul Multi, Iwa Garniwa, Uno Bintang Sudibyo

Makara Journal of Technology

The air gap length of the designed axial flux wound rotor (AFWR) synchronous generator is determined properly according to the design parameters. One of the distinct advantages of an axial flux (AF) machine is its adjustable air gap. An AF generator’s performance might be controlled by adjusting its air gap. The designed generator has a smallscale capacity that has 1 kW, 380 V, and 50 Hz. The windings are laid into slots made from laminated core. The slots are carved in the face of the stator and rotors. The generator has a single-double-sided slotted wound stator sandwiched between twin rotors. …

Production Optimization For Plan Of Gas Field Development Using Marginal Cost Analysis, Suprapto Soemardan, Widodo Wahyu Purwanto, Arsegianto Arsegianto

Makara Journal of Technology

Gas production rate is one of the most important variables affecting the feasibility plan of gas field development. It take into account reservoir characteristics, gas reserves, number of wells, production facilities, government take and market conditions. In this research, a mathematical model of gas production optimization has been developed using marginal cost analysis in determining the optimum gas production rate for economic profit, by employing the case study of Matindok Field. The results show that the optimum gas production rate is mainly affected by gas price duration and time of gas delivery. When the price of gas increases, the optimum …

Feedback Stabilization At Spear3, Daniel Kelley, Jeff Corbett

STAR Program Research Presentations

The SPEAR3 synchrotron lightsource at SLAC relies on a sophisticated radio frequency (RF) timing system to maintain current – electrons – in the storage ring. One problem SPEAR3 operators have dealt with is the thermal expansion of one of the cables supporting this RF timing system. As the cable expands and contracts with the diurnal rise and fall of the sun, the phase of the RF in the cable shifts. This shifting phase affects the timing accuracy of electron injections into the storage ring.

A common feedback control algorithm PID (Proportional Integral Derivative) has countless applications in engineering. PID feedback …

Investigation Of Negative Index In Dispersive, Chiral Materials Via Contra-Propagating Velocities Under Second-Order Dispersion (Gvd), Monish Ranjan Chatterjee, Tarig A. Algadey

Electrical and Computer Engineering Faculty Publications

Negative refractive index arises typically in metamaterials via multiple routes. One such avenue is the condition where the Poynting vector of the electromagnetic wave is in opposition to the group velocity in the material. An earlier work along this route in a chiral material led to the well-known result of requiring very large (non-realizable) chirality.

Thereafter, a combination of chirality together with first-order dispersion was examined using plane wave electromagnetic analysis. To arrive at the conclusions in that approach, the three wave velocities (energy, group and phase) were derived under first-order dispersion in permittivity, permeability and chirality. Negative index in …

Numerical Examination Of Acousto-Optic Bragg Interactions For Profiled Lightwaves Using A Transfer Function Formalism, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

Classically, acousto-optic (AO) interactions comprise scattering of photons by energetic phonons into higher and lower orders. Standard weak interaction theory describes diffraction in the Bragg regime as the propagation of a uniform plane wave of light through a uniform plane wave of sound, resulting in the well-known first- and zeroth-order diffraction.

Our preliminary investigation of the nature of wave diffraction and photon scattering from a Bragg cell under intensity feedback with profiled light beams indicates that the diffracted (upshifted photon) light continues to maintain the expected (uniform plane wave) behavior versus the optical phase shift in the cell within a …

Adaptive Wiener Filter Super-Resolution Of Color Filter Array Images, Barry K. Karch, Russell C. Hardie

Electrical and Computer Engineering Faculty Publications

Digital color cameras using a single detector array with a Bayer color filter array (CFA) require interpolation or demosaicing to estimate missing color information and provide full-color images. However, demosaicing does not specifically address fundamental undersampling and aliasing inherent in typical camera designs. Fast non-uniform interpolation based super-resolution (SR) is an attractive approach to reduce or eliminate aliasing and its relatively low computational load is amenable to real-time applications. The adaptive Wiener filter (AWF) SR algorithm was initially developed for grayscale imaging and has not previously been applied to color SR demosaicing. Here, we develop a novel fast SR method …

Analysis Of Parameter Tuning On Energy Efficiency In Asynchronous Circuits, Justin Thomas Roark

Graduate Theses and Dissertations

Power and energy consumption are the primary concern of the digital integrated circuit (IC) industry. Asynchronous logic, in the past several years, has increased in popularity due to its low power nature. This thesis analyzes a collection of array multipliers with different parameters to compare two asynchronous design paradigms, NULL Convention Logic (NCL) and Multi-Threshold NULL Convention Logic (MTNCL). Several commercially available pieces of software and custom scripts are used to analyze the asynchronous circuits and their components to provide the energy consumption estimation on various parts of each circuit. The analysis of the software results revealed that MTNCL circuits …