Transportation Engineering Commons^™

Evaluation Of Floorpan Tearing And Cable Splices For Cable Barrier Systems, Scott K. Rosenbaugh, Jason A. Hartwell, Robert W. Bielenberg, Ronald K. Faller, James C. Holloway, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

This research effort consisted of two objectives related to components of a prototype cable barrier system. The first objective was to mitigate the potential for vehicle floorpan tearing by modifying the cable guardrail posts. A bogie vehicle was equipped with a simulated floorpan designed to replicate the height, thickness, and strength of the floorpan of a Kia Rio vehicle. Baseline testing demonstrated that the top of the Midwest Weak Post (MWP) would contact, and crease the simulated floorpan, which matched the damage observed in actual full-scale vehicle crash tests. Once the test setup provided the desired results, various post configurations …

Mash Test No. 3-10 Of A Non-Proprietary, High-Tension Cable Median Barrier For Use In 6h:1v V-Ditch (Test No. Mwp-8), Dylan T. Meyer, Karla A. Lechtenberg, Ronald K. Faller, Robert W. Bielenberg, Scott K. Rosenbaugh, John D. Reid

Nebraska Department of Transportation: Research Reports

The Midwest States Pooled Fund Program has been developing a prototype design for a non-proprietary, high-tension cable median barrier for use in a 6H:1V V-ditch. This system incorporates four evenly spaced cables, Midwest Weak Posts (MWP) spaced at 8 to 16 ft (2.4-4.9 m) intervals, and a bolted, tabbed bracket to attach three or four cables to the sides of each post. According to the Manual for Assessing Safety Hardware (MASH) testing matrix for cable barriers installed within a 6H:1V median V-ditch, a series of eight full-scale tests are required to evaluate the safety performance of a system. A ninth …

Length Of Need And Minimum System Length For F-Shape Portable Concrete Barrier, Robert W. Bielenberg, Dylan T. Meyer, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Portable concrete barrier (PCB) systems are often used to redirect errant vehicles through a combination of inertial resistance, lateral friction loads, and tensile loads developed from the mass and friction of the barrier segments. State departments of transportation (DOTs) and other end users may wish to utilize minimal length PCB installations to shield a hazard or work zone or limit the number of barriers required on the upstream and downstream ends to reduce overall system length. However, concerns with the performance of shorter PCB installations include increased lateral deflections and working widths and barrier pocketing. Additionally, no impact testing has …

Testing And Evaluation Of Mash Tl-3 Transition Between Guardrail And Portable Concrete Barriers, Robert W. Bielenberg, Jessica L. Lingenfelter, Justine E. Kohtz, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Three full-scale vehicle crash tests were conducted according to the Manual for Assessing Safety Hardware (MASH) Test Level 3 (TL-3) safety performance criteria on a transition between the Midwest Guardrail System (MGS) and a portable concrete barrier (PCB) system. The transition system utilized for test nos. MGSPCB-1 through MGSPCB-3 consisted of a standard MGS that overlapped a series of F- shape PCB segments that approached the MGS at a 15H:1V flare. In the overlapped portion of the barrier systems, uniquely-designed blockout holders and a specialized W-beam end shoe mounting bracket were used to connect the systems.

In test no. MGSPCB-1, …

Increased Span Length For The Mgs Long-Span Guardrail System Part Ii: Full-Scale Crash Testing, Dylan T. Meyer, John D. Reid, Karla A. Lechtenberg, Robert W. Bielenberg, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

The objective of this research study was to design and evaluate the MGS long-span design for use with unsupported spans greater than 25 ft (7.6 m). Two full-scale crash tests were conducted to evaluate the MGS long-span system with increased span lengths and the use of UBSP posts adjacent to the long span. Both tests were conducted according to the TL- 3 criteria outlined in MASH. Both test nos. MGSLS-1 and MGSLS-2 were conducted with the 2270P vehicle impacting their respective critical impact points at a speed of 62 mph (100 km/h) and an angle of 25 degrees. Test no. …

Evaluation Of Tack Coating Practices For Asphalt Overlays In Nebraska, Soroosh Amelian, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

The strength of the bond between asphalt layers affects the lifespan of pavement structures. It is also a key factor in preventing major pavement distresses, such as slippage cracking and delamination. This research project evaluates and compares the effectiveness and performance of different tack coating approaches to ensure the proper bond strength is achieved in asphalt concrete (AC) interlayers through an experimental study. Various tack coat materials, including different types of emulsified asphalt and asphalt binders, at multiple application rates and dilution ratios were investigated. In the first part of this study, laboratory-prepared samples were used to evaluate the sensitivity …

Assessing Passenger Car Equivalency Factors For High Truck Percentages, Jianan Zhou, Laurence Rilett, Elizabeth Jones

Nebraska Department of Transportation: Research Reports

The Passenger Car Equivalent (PCE) values in the Highway Capacity Manual (HCM) 2010 might not be valid for western Nebraska freeway conditions. This is because: 1) Interstate 80 (I-80) experiences high truck percentages (25% to 60%), while the HCM provides PCE values up to 25% of the truck percentage; 2) the average speed of trucks are observed lower than passenger cars, which is incompatible with the HCM assumption that the free speed of all vehicle types is the same at level terrain; and 3) it is unclear whether the “average” truck used in the simulation study for PCE values in …

Development Of A Transition Between An Energy-Absorbing Concrete Barrier And A Rigid Concrete Butress, Tyler L. Schmidt, Ronald K. Faller, Jennifer D. Schmidt, John D. Reid, Robert W. Bielenberg, Scott Rosenbaugh

Nebraska Department of Transportation: Research Reports

From 2010 to 2015, MwRSF researchers developed the RESTORE barrier, which is a restorable MASH TL-4 median barrier with a steel and concrete rail supported by elastomer posts and steel skids. The research effort reported herein describes the initial development of a transition from the RESTORE barrier to a rigid TL-4 concrete buttress.

The previously-developed RESTORE barrier LS-DYNA model was validated against three full-scale vehicle crash tests. Several design concepts were generated through a series of brainstorming efforts. The primary transition concept consisted of a pin and loop connection between the RESTORE barrier and rigid concrete buttress, which was designed …

Use Of Recycled Crushed Concrete (Rcc) Fines For Potential Soil Stabilization, Lindeman Mark, Varilek Brandon, Lieska Halsey, Rick Gloe, Maria Olomi

Nebraska Department of Transportation: Research Reports

This study evaluated the use of Recycled Crushed Concrete (RCC) Fines for potential soil stabilization. Soil stabilization is the enhancement of subgrade stability to improve the constructability of successive pavement layers. Use of RCC fines may not only provide less costly alternatives for subgrade stabilization, but their use may also alleviate landfill disposal challenges.

Cable-To-Post Attachments For Use In Non-Proprietary High-Tension Cable Median Barrier – Phase Ii, Scott K. Rosenbaugh, Robert W. Bielenberg, Jessica L. Lingenfelter, Ronald K. Faller, John D. Reid, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

The objective of this study was to reevaluate and improve the existing cable-to-post attachment hardware that is utilized in the non-proprietary cable barrier being developed at MwRSF. The study focused on redesigning the bolted, tabbed bracket (V10) to eliminate the bolt, reduce the number of components per bracket, eliminate the need for tools during installation, and reduce the number of small parts. Three attachment concepts were selected for evaluation through dynamic testing: (1) the key plate attachment; (2) the wire lock pin attachment; and (3) the pinned back attachment. Each attachment prototype was subjected to two vertical and two lateral …

Evaluation Of Lightweight Pieces In Aggregates, Mark Lindemann, Doug Macke, Jim Wilken, John Ebito, Mark Hassler, Lieska Halsey, Bob Seger

Nebraska Department of Transportation: Research Reports

No abstract provided.

Nebraska Data Collection, Keyvan Zare Rami, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

Automated pavement performance data collection is a method that uses advanced technology to collect detailed road surface distress information at traffic speed. Agencies are driven to use automated survey techniques to enhance or replace their current manual distress survey because of the advantages of objective measurements, safety benefits, and reduced measurement time. As agencies move toward the transition to fully automated data collection methods, there are common concerns regarding how the output of the new method will match the current manual survey ratings and how they will be adopted into the existing Pavement Management System (PMS). This study evaluates the …

Cable Median Barrier Failure Analysis And Remediation Phase Ii, Cody S. Stolle, Dean L. Sicking, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Cable median barrier crashes from a total of 12 states were analyzed. Crash data included scene diagrams, photographs, and field measurements, crash narratives, although the availability of data in each crash varied.

Major contributors to penetration crash propensity were identified: diving underride, in which the front end of the vehicle dropped below the bottom cable; prying, in which the vehicle profile caused cable separation or lifting; override; bouncing override, in which the vehicle rebounded after contact with the back slope and bounced over the top of the barrier; system failure, in which one component failure or design failure prevented the …

The Fuel Tax Compliance Unit: An Evaluation And Analysis Of Results, Suzanne Perkins Sapp

Kentucky Transportation Center Research Report

The construction and maintenance of our nation's system of roads and highways is a major financial challenge. A majority of the responsibility for financing public roads and highways lies with state governments. Almost all states have special funds called Road Funds into which user fees and taxes associated with highway use are deposited. Unfortunately, Road Fund revenue growth has been slow due to the relative inelasticity of its revenue sources. At the same time, states face resistance to tax increases designed to enhance Road Fund revenues. One method of increasing such revenues, without increasing taxes, is to reduce evasion. Increased …

Roadway Related Tort Liability And Risk Management: 5th Edition, Kenneth R. Agent, Daniel S. Turner

Kentucky Transportation Center Research Report

This training material has been prepared to address the tort liability problems faced by the Kentucky Transportation Cabinet and Kentucky local governments. The manual defines the problem by reviewing the national picture of generally growing numbers of suits and escalating financial losses from suits against highway agencies.

The manual also sets out solutions, and reviews actions, which can decrease the exposure of highway agencies to these suits. This risk management concept is emphasized throughout the manual.