Transportation Engineering Commons^™

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Performance Evaluation Of Inverted Tee (It) Bridge System, Garrett P. Martindale, Daniel Watson, Antony Mohsen Kamal Masoud Kodsy, Mostafa Abo El-Khier, Richard L. Wood, George Morcous

Nebraska Department of Transportation: Research Reports

The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) researchers and Nebraska Department of Transportation (NDOT) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Extensive longitudinal and transverse deck cracking have been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer, …

Structural Vulnerability Of Coastal Bridges Under Extreme Hurricane Conditions, Arturo Montoya, Adolfo Matamoros, Firat Testik, Reza Nasouri, Adnan Shahriar, Arsalan Majlesi

Publications

This work presents the results of a numerical study evaluating the response of coastal bridges due to hurricane-induced waves. The analyses were conducted using the Coupled Eulerian-Lagrangian (CEL) approach, available on the commercial finite element software Abaqus, which allows modeling the interaction between water and the bridge. The work concentrated on (1) establishing an approach for modeling the desired wave characteristics (i.e., wave height, and frequency) within the CEL simulation, (2) conducting simulations using actual bridge dimensions of historically damaged bridges, (3) analyzing a range of foundation flexibilities to determine its effect on the uplift and shear forces acting on …

Save Our Sound Obx, Inc. V. North Carolina Department Of Transportation, Mitch L. Werbell V

Public Land & Resources Law Review

The Fourth Circuit Court of Appeals recently ruled in favor of several governmental agencies seeking to construct a new bridge in the Pamlico Sound adjacent to North Carolina’s Outer Banks. For years, state and federal agencies have put forth a massive coordinated effort to address the constant weather damage and erosion which occurs to a section of North Carolina Highway 12. The court found the agencies properly cleared NEPA’s environmental review requirements for the bridge’s construction. Additionally, the opponent-litigants’ efforts to add claims challenging the project, based on new information about a shipwreck in the bridge’s path, were futile.

Detection Of Multiple Flaws In Concrete Bridge Decks Using Ultrasonic Wave Propagation, Ece Erdogmus, Eric Garcia, Michael Schuller, Donald Harvey, Kelsey Stithem, Monica Houck

Nebraska Department of Transportation: Research Reports

No abstract provided.

Coastal Bridges Under Hurricane Stresses Along The Texas And Louisiana Coast, Adolfo Matamoros, Firat Testik

Data

Corresponding data set for Tran-SET Project No. 17STTSA02. Abstract of the final report is stated below for reference:

"The main objective of this study was to develop a high-resolution model capable of simulating the response of bridge structures to hydrodynamic loads for hurricane design conditions (i.e. surge height, wave height, and frequency) expected in the Texas-Louisiana coast. The model relied on Coupled Eulerian-Lagrangian techniques (CEL) where solids are simulated with Lagrangian meshes, while fluids are simulated using Eulerian meshes, and was calibrated using historical data from wave impact laboratory tests. Two high resolution models were created, the first of a …

Coastal Bridges Under Hurricane Stresses Along The Texas And Louisiana Coast, Adolfo Matamoros, Firat Testik

Publications

The main objective of this study is to develop a high-resolution model capable of simulating the response of bridge structures to hydrodynamic loads for hurricane design conditions (i.e., surge height, wave height, and frequency) expected in the Texas-Louisiana coast. The model relied on Coupled Eulerian-Lagrangian (CEL) techniques where solids are simulated with Lagrangian meshes, while fluids are simulated using Eulerian meshes, and was calibrated using historical data from wave impact laboratory tests. Two high resolution models were created, the first of a tsunami wave impact test conducted at Oregon State University and the second of a bridge located in the …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

On The Fatigue Of Headed Shear Studs In Steel-Concrete Composite Bridge Girders, Brianna Laurene Ovuoba

Graduate Theses and Dissertations

Shear connectors are commonly used in steel bridges to join the concrete deck and steel superstructure, providing a mechanism for shear transfer across the steel-concrete interface. The most common shear connector is the headed shear stud. In the current AASHTO LRFD Bridge Specifications on composite design, shear stud fatigue often governs over static strength, and a large number of shear connectors often result. This dissertation investigates headed shear stud fatigue capacities and demands, and provides insight into conservancies in existing design specifications through examination of existing high-traffic bridge performance.

To investigate stud capacity, a total of six high-cycle fatigue tests …

Bridge Build, Andrew Little

Student Scholarship

Bridge build design that includes not only a building process, but a research paper to make the best build possible as well.

Cfrp Strengthening Of Ky 583 Over The Bluegrass Parkway Bridge In Hardin Country, Abheetha Peiris, Issam E. Harik

Kentucky Transportation Center Research Report

The report details the planning, design, and construction of the retrofit measure on the KY 583 Bridge (047B00072N), which traverses the Bluegrass Parkway in Hardin County, Kentucky. Reinforced concrete girders within the span over the eastbound Bluegrass Parkway of the bridge had cracks that led to concrete delamination and deterioration of the girders.

To remedy the problem, triaxial carbon fiber reinforced polymer (CFRP) fabric sheets were selected to perform a retrofit due to their strength, conformability, and flexibility. The concrete surface, over which the fabric sheets were applied, were first prepared by removing all spalling and deteriorated concrete, which exposed …

Evaluation Of Adjustable Continuity Joint Variations For Use In The Restore Barrier, Scott Rosenbaugh, Jennifer D. Schmidt, Ronald K. Faller, James C. Holloway

Nebraska Department of Transportation: Research Reports

During MASH TL-4 full-scale crash testing of the RESTORE barrier, concrete cracking and spalling was observed on the barrier beams that would likely require repairs or replacement. This study sought to evaluate joint design alternatives for use in the RESTORE barrier in order to limit the amount of system damage. Three variations of the Adjustable Continuity Joint (ACJ) were identified as potential modifications: 1) incorporating rubber bearing pads within the ACJ, 2) utilizing normal weight concrete instead of lightweight concrete, and 3) incorporating a steel end cap into the ends of the beam segments.

Four dynamic component tests were conducted …

Condition Factor Calibration For Load And Resistance Factor Rating Of Steel Girder Bridges, Joshua Steelman, Pranav M. Shakya

Nebraska Department of Transportation: Research Reports

Load and Resistance Factor Rating (LRFR) is a reliability-based rating procedure complementary to Load and Resistance Factor Design (LRFD). The intent of LRFR is to provide consistent reliability for all bridges regardless of in-situ condition. The primary difference between design and rating is the uncertain severity and location of deterioration, including the potential future loss of strength for an element already evidencing deterioration. Ostensibly, these uncertainties are addressed by applying an additional strength reduction factor: the condition factor, ϕc. Currently, condition factors are nominally correlated to the condition of the member, which can be Good, Fair, or Poor. However, definitions …

Hillman Composite Beam (Hcb®), Purdue Ect Team

ECT Fact Sheets Archive

The Hillman-Composite Beam (HCB®), is an innovative structural member for use in highway and railroad bridges as well as marine facilities. The HCB is essentially a lightweight reinforced concrete beam strengthened and protected by a corrosion-resistant and resilient Fiberglass Reinforced Polymer (FRP) shell.

The beam is comprised of three main components, a concrete arch (compression reinforcement), an FRP bottom flange encapsulating steel strands tying the ends of the arch together (tension reinforcement) and the FRP shell. Galvanized Rebar “shear connectors” are used to make the beam composite with the concrete deck in the same manner as pre-stressed concrete beams.

The …

Protocol To Evaluate And Load Rate Existing Bridges, Maria Szerszen, Ali Alhajami

Nebraska Department of Transportation: Research Reports

Load tests can be used to verify component and system performance under a known live load and provide an alternative evaluation methodology to analytically computed the load rating of a bridge. Procedures for nondestructive load testing, which involves field observations and measurements of in- service bridges and field testing often can revel additional capacity since analytical bridge rating tend to be fairly conservative. The goal of presented research was to develop a data-driven rating process to assess and rate bridges. This data-driven rating system reduces the subjective judgment of the bridge inspectors through the use of computer models and field …

Continuous Long-Term Health Monitoring Using Ultrasonic Wave Propagation, Ece Erdogmus

Nebraska Department of Transportation: Research Reports

No abstract provided.

Development Of A Transition Between An Energy-Absorbing Concrete Barrier And A Rigid Concrete Butress, Tyler L. Schmidt, Ronald K. Faller, Jennifer D. Schmidt, John D. Reid, Robert W. Bielenberg, Scott Rosenbaugh

Nebraska Department of Transportation: Research Reports

From 2010 to 2015, MwRSF researchers developed the RESTORE barrier, which is a restorable MASH TL-4 median barrier with a steel and concrete rail supported by elastomer posts and steel skids. The research effort reported herein describes the initial development of a transition from the RESTORE barrier to a rigid TL-4 concrete buttress.

The previously-developed RESTORE barrier LS-DYNA model was validated against three full-scale vehicle crash tests. Several design concepts were generated through a series of brainstorming efforts. The primary transition concept consisted of a pin and loop connection between the RESTORE barrier and rigid concrete buttress, which was designed …

Performance Assessment Of Deteriorated And Retrofitted Steel Hp Piles, Joshua Steelman, Steven Stauffer

Nebraska Department of Transportation: Research Reports

No abstract provided.

Development Of Pre-Stressed Cfrp Fatigue Retrofits For Common Steel Bridge Connections, Korey Albert Pough

Graduate Theses and Dissertations

Aging or deterioration of the nation’s bridge infrastructure is a significant issue that requires attention. Causes for much of this deterioration can be attributed to two main factors, 1) corrosion, and 2) metallic fatigue, both of which work together to reduce the strength and serviceability of bridge components over time. In many instances, strengthening of bridge components using localized retrofits offers an economical and fast solution for increasing the longevity of existing steel bridges; however, such retrofits must be resilient to further corrosion and fatigue damage. In this study, a localized retrofit is developed using pre-stressed Carbon Fiber Reinforced Polymer …

Integrated 3d Bridge-Condition Visualization (Bcv) To Facilitate Element-Based Bridge Condition Rating (Ebcr), Zhigang Shen, Wayne Jensen

Nebraska Department of Transportation: Research Reports

Routine inspection and maintenance records are essential for bridges to function well throughout their intended lifespan. Although existing bridge management systems are efficient at data storage, it is difficult to conduct comprehensive data analysis and management due to the lack of data integration mechanism. Engineers have to manually put many pieces of bridge drawings and inspection data together to make maintenance or repair/rehab decisions. Building information modeling (BIM) can be applied in bridge asset management area, including bridge inspection/rating to help to integrate the many data pieces. In this project we developed a 3D bridge inspection data management system, using …

Investigation Of Closure Pour Elimination For Phased Construction Of Steel Girder Bridges, Terri R. Norton, Armando Shane

Nebraska Department of Transportation: Research Reports

No abstract provided.

Repair Of I-65 Expressway Bridges Using Carbon Fiber Reinforced Polymer (Cfrp) Composites, Ching Chiaw Choo, Abheetha Peiris, Issam E. Harik

Kentucky Transportation Center Research Report

This report documents the repair of five locations along the I-65 Expressway in Jefferson County, KY. The repair involved: (1) the precast prestressed concrete girder spans between Jacob Street and Gray Street, (2) the reinforced concrete bearing pads of Bridge Pier 4 at the intersection of Jefferson Street and Preston Street, (3) the reinforced concrete bearing pads of Bridge Pier 6 near the intersection of Main Street and Hancock Street, (4) the precast prestressed concrete girder spans between Chestnut Street and Gray Street and (5) the reinforced concrete pier column on East Muhammad Ali Blvd.

The precast prestressed concrete girders …

Repair Using Steel Fiber Reinforced Polymer On Us 150 Bridges, Ching Chiaw Choo, Abheetha Peiris, Issam E. Harik

Kentucky Transportation Center Research Report

The report details the pre-construction monitoring, planning and design, and construction of the retrofit measures on the US150 bridge over Beech Fork River in Nelson County, KY and Cartwright Creek bridge on the border of Washington-Nelson County, KY. All reinforced concrete girders of the five-span Beech Fork River bridge and three-span Cartwright Creek bridge of deck-girder construction had developed diagonal cracks near or at the transition of the variable-and-constant depth regions.

To remedy the problem steel fiber reinforced polymer (SFRP) sheets were selected as the means of retrofit due to their strength and stiffness, as well as conformability and flexibility. …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …

Application Of Multi-Hazard Seismic-Blast Detailing For Highway Bridges, Dominique Morton Torres

Dissertations and Theses

The increase of worldwide terrorist attacks on public transportation has heightened our concerns of protecting the nation’s transportation infrastructure. Highway bridges are an attractive target for terrorist attacks due to ease of accessibility and their overall importance to society. The primary objective of this research is to investigate multi-hazard seismic-blast correlations of blast-induced bridge components through numerical simulations of a high-precision finite element model of a typical highway bridge in New York. Seismic-detailing for blast loading on bridges has been investigated to study the correlations between seismic design for blast load effects. High-precision 3D Finite Element models of bridges detailed …

Evaluation Of The Environmental Impacts Of Bridge Deck Runoff, Shannon L. Bartelt-Hunt, Lauren Swadener, Ekizabeth G. Jones

Nebraska Department of Transportation: Research Reports

Bridges are located in very close proximity to receiving waters, and regulatory agencies often require specific stormwater control measures for bridge deck runoff. While there is some information available on roadway runoff, few studies have focused on bridge deck runoff. Currently, there is no information available regarding the impacts of bridge deck runoff on receiving waters in Nebraska. Due to the cost, maintenance, and design issues associated with implementing structural controls for bridge deck runoff, it is important to develop a better understanding of the relationship between bridge deck runoff and potential impacts to receiving streams. The objectives of this …

Development And Deployment Of Aluminum Bridge Decks, Ching Chiaw Choo, Abheetha Peiris, Issam E. Harik

Kentucky Transportation Center Research Report

This report contains the analysis and retrofit of a steel truss bridge on KY 974 over Howard Creek in Clark County, Kentucky. The bridge had major corrosion and damage to the steel stringers, along with cracking and leaching occurring in the concrete bridge deck. The retrofit involves the replacement of the corroded steel stringers and the damaged concrete bridge deck. The original concrete deck was removed and replaced by light-weight high-strength aluminum deck panels. The aluminum deck panels, each 2-m wide, were assembled at the site and connected to each other and to the bottom steel stringers using special clamps …

Safety Stock Estimation Of Unit Load Devices For International Airline Operations, Hua-An Lu, Chien-Yi Chen

Journal of Marine Science and Technology–Taiwan

Unit load devices (ULDs) are used to load air cargo and passengers’ checked baggage for wide-bodied aircraft operations. Since ULDs are reusable at the destination, airlines can invest in an appropriate fleet size for their requirements. The estimation of safety stock levels for every operating airport is a premeditated task because airlines must prepare enough devices for the outbound consignments of each flight. The variance of the number of used devices for each arrival and departure flight will influence the stock level of an airport. For scheduled international services, this study proposes an analytic method based on a cyclically time-sequenced …

Implementation Of Remote Sensing Technology On The I-64 Bridge Over Us60, Issam E. Harik, Ching Chiaw Choo, Abheetha Peiris, Dan Eaton

Kentucky Transportation Center Research Report

Remote sensing devices have been implemented on the I-64 Bridges over US60 in Franklin County, KY. One of the girders in the westbound bridge has been previously repaired due to unexpected fatigue cracking. The exterior girder in the eastbound bridge has shown signs of impacts due to the traversing trucks on US60. Sensing and recording devices such as strain and temperature gauges, infrared sensors, ultrasonic height detectors, and an accelerometer have been installed. Specifically, eleven strain gauges are used on the repaired girder, impacted girders, and girders adjacent to them. Two sets of infrared sensors, ultrasonic detectors, and video cameras …

Rapid Construction Of Pacific Street Bridge, Kromel E. Hanna, George Morcous, Maher K. Tadros

Nebraska Department of Transportation: Research Reports

No abstract provided.