Transportation Engineering Commons^™

A Durability Evaluation Of Class B Concrete Bridge Substructures Under West Virginia Freeze–Thaw Conditions, Nathaniel Wayne Dunbar

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study evaluates whether the West Virginia Division of Highways (WVDOH) Class B concrete specification for bridge substructures remains adequate under modern durability and design-life expectations. The current specification, which permits a minimum compressive strength of 3,000 psi, reflects practices established when shorter service lives were generally assumed. Modern AASHTO LRFD provisions are based on a 75-year design life, raising concern that this lower-strength concrete may not provide sufficient durability under West Virginia’s climatic conditions.

To address this issue, bridge inspection data, regional climate mapping, and durability modeling were used to assess the condition and performance of concrete substructures across …

The State Of The City's Bridges, Leo G. Miranda

Capstones

An analysis by NYCity News Service of 2024 federal bridge inspection found that 118 segments of city bridges are in poor condition, around 8% of all bridges citywide. Among these are segments of major highways and bridges like the Brooklyn Queens Expressway, FDR Drive, Harlem River Drive, Grand Central Parkway and even a part of the iconic Brooklyn Bridge. On a single stretch of highway, where the Grand Central Parkway and the Whitestone Expressway meet in Queens, there are seven parts of highway or ramps in poor condition.

Bridge segments can be any raised roadway that passes over another parkway, …

Modeling The Influence Of Internal Factors On Vehicular Mobility Performance, Aziz Mdimi

Tanzania Journal of Engineering and Technology (TJET)

Traffic mobility is significantly influenced by road conditions and the internal factors governing vehicular performance. Internal factors play a crucial role in vehicular mobility, influencing vehicles operate and performance. While existing vehicular mobility models primarily address external factors, external factors such as governor, engine, gear train and differential unit remain underexplored. This study formulates a comprehensive model to address this gap, focusing on the internal components that affect vehicular mobility. The proposed model employs both analytical and numerical methods to derive transfer functions for these subsystems using Matrix Laboratory (MATLAB), aiming to capture the dynamic behavior of vehicles under various …

Final Design Of Legion Hall Revitalization In Potter, Nebraska, Madison Brennfoerder

Honors Program: Senior Projects (Public)

This project was conducted to renovate and revitalize the Legion Hall community center in the Village of Potter located in western Nebraska north of the Interstate. The work completed for this project can be separated into five disciplines: Hydrologic & Hydraulic Design, Geotechnical Analysis, Structural Analysis, Environmental Analysis, and Transportation Design. Legion Hall is a historical building within The Village of Potter which was built in 1917. The Village of Potter has recently acquired the rights to the hall and is seeking to revitalize the historical community center to increase tourism in the village.

Demystifying Utility Coordination: Understanding The Basics, Josshe I. Palm

Purdue Road School

This session will explain utility coordination to non-utility coordinators. It will help educate others about the role and responsibilities of a utility coordinator, an OSA, easy UC and design mistakes to avoid, scope and design considerations, items commonly overlooked, when to coordinate SUE, and how to work with your UC to request a letting adjustment. We will also highlight UC submittals and allow time for questions about the UC’s role in a project’s success.

Enhancing Bridge Resilience And Overheight Vehicle Mitigation Through Innovative Sacrificial Cushion Systems, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Transportation departments have made significant strides in addressing the challenges posed by the increasing weights of trucks on bridges. While there is a growing awareness of overheight vehicle collisions with bridges, implementing effective countermeasures remains limited. The susceptibility of bridges to damage from such collisions is on the rise, further exacerbated by unpredictable lateral impact forces. This study employs nonlinear impact analysis to assess the response of an unprotected vehicle-girder model, yielding realistic deformation outcomes comparable to observed impacts on the US-61 bridge. Predictions for a truck traveling at 112.65 km/h indicate deformations of 0.229 m, 0.161 m, and 0.271 …

Improvement In Benefit-Cost Analysis Of Bridges Through Assessment Of Secondary Benefits And Defect Based Maintenance Cost, Shadman Sakib

Civil Engineering Theses - Archive

Benefit-cost Analysis (BCA) is conducted prior to federal grant allocation for bridge replacement and enhancement projects to prioritize decision-making. Benefits are measured based on total bridge closures, requiring vehicles to take alternate detour paths. Primary benefits are the direct user costs such as travel time saving or emission costs. However, there are more secondary benefits that are intangible and hard to monetize, but United States Department of Transportation (USDOT) guidelines suggest considering them wherever possible. There are lack of US based data and research also no set guideline by authority.

Apart from calculating primary benefits for a 95 sample of …

Railroad Condition Monitoring Using Distributed Acoustic Sensing And Deep Learning Techniques, Md Arifur Rahman

College of Graduate Studies: Theses & Dissertations

Proper condition monitoring has been a major issue among railroad administrations since it might cause catastrophic dilemmas that lead to fatalities or damage to the infrastructure. Although various aspects of train safety have been conducted by scholars, in-motion monitoring detection of defect occurrence, cause, and severity is still a big concern. Hence extensive studies are still required to enhance the accuracy of inspection methods for railroad condition monitoring (CM). Distributed acoustic sensing (DAS) has been recognized as a promising method because of its sensing capabilities over long distances and for massive structures. As DAS produces large datasets, algorithms for precise …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Ai-Based Bridge And Road Inspection Framework Using Drones, Hovannes Kulhandjian

Mineta Transportation Institute

There are over 590,000 bridges dispersed across the roadway network that stretches across the United States alone. Each bridge with a length of 20 feet or greater must be inspected at least once every 24 months, according to the Federal Highway Act (FHWA) of 1968. This research developed an artificial intelligence (AI)-based framework for bridge and road inspection using drones with multiple sensors collecting capabilities. It is not sufficient to conduct inspections of bridges and roads using cameras alone, so the research team utilized an infrared (IR) camera along with a high-resolution optical camera. In many instances, the IR camera …

System-Of-Systems Integration For Civil Infrastructures Resiliency Toward Multihazard Events, Vahid Balali

Mineta Transportation Institute

Civil infrastructure systems—facilities that supply principal services, such as electricity, water, transportation, etc., to a community—are the backbone of modern society. These systems are frequently subject to multi-hazard events, such as earthquakes. The poor resiliency of these infrastructures results in many human casualties and significant economic losses every year. An outline of a holistic view that considers how different civil infrastructure systems operate independently and how they interact and communicate with each other is required to have a resilient infrastructure system. More specifically a systems engineering approach is required to enable infrastructure to remain resilient in the case of extreme …

Fiber-Based Seismic Damage And Collapse Assessment Of Reinforced Concrete Single-Column Pier-Supported Bridges Using Damage Indices, Yu-Fu Ko, Jessica Gonzalez

Mineta Transportation Institute

Near-fault earthquakes can have major effects on transportation systems due to the structural damage they impose on bridges. Therefore, it is imperative to assess the seismic damage of bridges appropriately, and this research focuses on reinforced concrete (RC) bridges. This research advances the seismic performance assessment of RC single-column pier-supported bridges with flexural failure under near-fault ground motion by use of ductility coefficients and damage indices. The methodology included modeling fiber-based nonlinear beam-column elements to simulate the damage development process of RC bridge piers under earthquake loadings, considering the global buckling of longitudinal steel bars, examining the cracking and spalling …

Investigation And Modification Of Single-Post Aluminum Sign Supports For Mash Crashworthiness, Rodrigo Quintero

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Traffic signs are used to display information to drivers and are one of the most commonly encountered roadside structures. Although they are a vital traffic control device, signs can pose a significant safety risk to errant drivers due to their extensive placement and proximity to the roadway. Therefore, traffic signs and their supports must be designed with crashworthiness in mind to reduce the likelihood of injury in the event of a vehicle impact. Prior to 2009, these systems were evaluated using the crash testing criteria found in the National Cooperative Highway Research Program (NCHRP) Report No. 350 [1]. Currently, they …

Columbus, Nebraska: Southern Housing Development Design Proposal, Ryan Weyers, Caiden Dynek, Alex Papa, Brexton Robertson, Kaden Perala

Honors Program: Senior Projects (Public)

The following paper proposes the design and creation of a new housing development in the city of Columbus, Nebraska in a lot to the south of the city and directly north of the Columbus wastewater treatment plant. The goal of this proposal is to provide readers with confidence that our company is the most qualified to complete the project and will create the safest, most comfortable, most efficient, and most cost-effective final design. This proposal seeks to offer a solution to the lack of affordable housing for the growing workforce in Columbus. In order to arrive at this solution, each …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

Feasibility Study For A Continuous Mansfield Hollow State Park Multi-Use Path, Owen P. Spangler

Honors Scholar Theses

This report aims to design a pedestrian river crossing that connects the north and south ends of Mansfield Hollow State Park, utilizing both a new paved pathway and bridge construction. This report first uses GIS data to complete a feasibility study on pathway routing and cost. A preliminary route was selected based on grading and cost analysis. The requirements for constructing a multi-use pathway in the State of Connecticut were then explored, attempting to find a best-fit pathway alignment to accomplish that goal. Through a lengthy literature review, it was found that the pathway design would have to deviate from …

Using Thermal Remote Sensing To Quantify Impact Of Traffic On Urban Heat Islands During Covid, My-Thu Tran, Bo Yang

Mineta Transportation Institute

A three-month lockdown in the U.S. at the beginning of the COVID-19 outbreak in 2020 greatly reduced the traffic volume in many cities, especially large metropolitan areas such as the San Francisco Bay Area. This research explores the impact of transportation on climate change by using remote sensing technology and statistical analysis during the COVID-19 lockdown. Using thermal satellite data, this research measures the intensity of the urban heat island, the main driver for climate change during the urbanization process. The research team acquired morning and afternoon MODIS data in the same periods in 2019 before the pandemic and 2020 …

Environmental Assessments On A Local Project, Robert Winebrinner, Trevor Wieseke, Summer R. Elmore, Alison Krupski, Mike Maurovich

Purdue Road School

This presentation will go through the environmental process of a recent $125M local project within Noblesville. What are the major differences between the National Environmental Policy Act (NEPA) and State Environmental Policy Act (SEPA) process as it relates to an environmental assessment (EA)? What is required, what is not required, and what is optional? How long does the process take? Join us as we walk through this exciting process and experience.

Additive Manufacturing Of Engineered Cementitious Composites With Ultra-High Tensile Ductility, Amir Bakhshi

Civil Engineering ETDs

One of the critical factors in the development of additive manufacturing in the construction industry is designing suitable materials for 3D printing applications. 3D concrete printing (3DCP) has gained significant attention due to the abundance and availability of concrete. However, concrete is a brittle material and, without proper reinforcement, cannot meet the requirements for structural purposes. Engineered Cementitious Composites (ECC), known for high ductility, and strain-hardening with low fiber contents, can potentially eliminate the need for steel reinforcement in 3D printing without any need for manual placement of reinforcement. A set of systematic tests on ECC mix designs' fresh and …

Nondestructive Evaluation Of Structural Defects In Concrete Slabs, Ehsanul Kabir

College of Graduate Studies: Theses & Dissertations

Nondestructive testing (NDT) is a reliable method for determining the structural integrity of new and old construction and understanding the condition of structural defects. It is widely acknowledged that the interpretation of nondestructive evaluation (NDE) has a significant impact on the reliability and consistency of this technology. However, NDT data acquisition remains subjective and heavily dependent on the operator’s knowledge and expertise. As a result, there are still issues to be resolved regarding the imaging and diagnostic procedures for NDT-based concrete inspection. NDT methods such as ground penetrating radar (GPR), and impact-echo (IE), have been extensively used to inspect concrete …

Implementation Of Ground Penetrating Radar (Gpr) And Complementary Non-Destructive Testing On Concrete Structures, Macy Spears

College of Graduate Studies: Theses & Dissertations

This study analyzes the application and practicality of different non-destructive testing (NDT) methods for the inspection of reinforced concrete. There are two studies discussed in this paper. The first one is a laboratory investigation, utilizing ground penetrating radar (GPR) on concrete slabs that consisted of simulated defects to mimic those found in real concrete structures. This served as a preliminary experiment to verify the GPR data with the design of the slabs. The following study describes a field investigation on an old bridge deck, which involved multiple testing methods. The techniques used were GPR, impact echo (IE), ultrasonic pulse echo …

Evaluations Of Frp Composite Coupons Under Impact And Puncture, Lekhnath Bhandari

Graduate Theses, Dissertations, and Problem Reports (ETD)

Evaluations of FRP Composite Coupons Under Impact and Puncture

Lekhnath Bhandari

Railroad tank cars are the main mode of transportation for carrying flammable liquids and other hazardous materials, in any mode of ground transportation system. These tank cars, if punctured during derailments may explode releasing large amounts of hazardous materials and posing serious threats to human life and leading to economic losses. To minimize such catastrophes, in 2015, United States Department of Transportation (USDOT) proposed to improve the thermal and puncture performances of these tank cars and introduced two new design specifications: DOT-117 and DOT-117R. Tank cars with 9/16 inches …

Improving Building Cfd Peak Pressure Computation Using Les With A Focus On Inflow Turbulence Methods And Grid Spacing Size., Zahra Mansouri

Graduate Theses and Dissertations

Structural failures by extreme winds often leads to economic losses and even deaths. Proper design of buildings requires accurate estimation of wind loads to prevent structural damage. Using routine guidelines generally leads to the underestimation of buildings’ peak pressures, in which most failures occur. To estimate wind loads more accurately three different methods (i.e., field measurement, wind tunnel (WT), and computational fluid dynamics (CFD)) are in use. A well-validated CFD provides more flow field details at lower costs compared to field measurements and WT. As strong winds are extremely turbulent, the effects of turbulence in wind should be incorporated into …

Effect Of Varying Amounts Of Sandstone On The Performance Of Asphalt Mixtures In Arkansas, David Murphy

Graduate Theses and Dissertations

There are many different species and subspecies of aggregate used across the state of Arkansas, and the rest the country. However, it cannot be presumed that the amount and type of these aggregates will be compatible with the commonly used asphalt binder of an area; this can lead to performance issues and premature pavement damage. It has been suspected in Arkansas that an excessive amount of sandstone in asphalt mixtures may be a culprit of some of these premature pavement damage issues, especially regarding the moisture susceptibility of a pavement. This study aimed to analyze the performance effects of using …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Contracting Strategies: A Different Approach To Address Long-Term Performance, Maria Calahorra-Jimenez

Mineta Transportation Institute

For cost-efficiency, public safety, and sustainability, improving long-term performance in highway projects is imperative for public administrations. Project delivery and procurement methods provide an opportunity to align design and construction processes with this goal. While previous studies have explored whether project delivery methods impact the long-term performance of highway projects, these studies did not focus on how core elements within project procurement relate to long-term performance. Thus, to fill this gap, this research explores how and to what extent long-term evaluation criteria are considered in design-build best-value procurement of highway projects. To this end, the team conducted content analysis on …

Modelling Monthly Rainfall Of Calabar, Nigeria Using Box-Jenkins (Arima) Method, Francis Ogbozige

Tanzania Journal of Engineering and Technology (TJET)

Rainfall has both positive and negative effects on human activities hence, correct prediction of the period of occurrence is very essential. However, the traditional method of predicting months of heavy rainfall is gradually fading out as irregular rainfall pattern is been experienced in most regions of the world. The rainfall pattern in Calabar city in Southern Nigeria has been reported in past literatures of being irregular. Hence, this research applied the Auto-Regressive Integrated Moving Average (ARIMA) also known as Box-Jenkins method to model the rainfall pattern of Calabar. This was achieved by subjecting 50years monthly rainfall (1971 – 2020) to …

Refining Particle Size Specification For Asphalt Emulsion, Pedro Luis Diaz Romero

Graduate Theses and Dissertations

Pavements begin to deteriorate as soon as they are constructed, and traffic is released. The rate at which a pavement deteriorates depends on the material quality, the environment, and the loads carried. To properly preserve pavements and extend their life, various pavement preservation treatments are used. For flexible pavements, a considerable number of these treatments use asphalt emulsion (which are refer to simply emulsions from here on). Emulsions are classified based on their particle charge and reactivity. Emulsions used in chip seals are usually of rapid set reactivity and are classified based on tests over fifty years old.

It has …

Analyzing Vulnerabilities In The Northwest Arkansas Highway Network Using Mathematical Optimization, Brandon Jerome

Industrial Engineering Undergraduate Honors Theses

The highway and bridge network is a critical infrastructure that allows for the free transportation of citizens and enables truck-borne freight transportation. Disruption of this system could be caused by a terrorist attack, natural disaster, growth of population, required repairs and upgrades, or collapse caused by old age or malfunction. In the event of a disruption cities and regions can experience increased traffic and supply chain shortages, thus causing cascading effects throughout surrounding areas. With this motivation, we develop a network interdiction optimization model to identify a limited subset of roads that, if disrupted, causes the greatest increase in the …

Comparing The Stiffness Of Cold In-Place Recycled Asphalt Pavement To Hot Mix Asphalt: Determining The Reproducibility Of The Stiffness Rebound Test, Tanner Turben

Civil Engineering Undergraduate Honors Theses

The Stiffness Raveling Mechanism Test (SRMT) was originally developed as an indirect measure of pavement stiffness to determine a pavement’s tendency to ravel, a type of damage. Regarding rehabilitation of existing roadways by Full Depth Reclamation (FDR) Cold In-Place Recycling (CIR), concern of field repeatability was expressed (Hill & Braham, 2016).

An analysis of lab-compacted samples of CIR and Hot Mix Asphalt (HMA) was performed to determine if the results could be reproduced between CIR and HMA. Additionally, the experiment observed the effects of percent air voids, temperature, and moisture conditioning on CIR and HMA. Three samples were prepared for …