Structural Engineering Commons^™

Ccfss News August 1994, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Behavior Of Web Elements With Openings Subjected To Bending, Shear And The Combination Of Bending And Shear, Ming-Yang Shan, Roger A. Laboube, Wei-Wen Yu

CCFSS Library (1939 - present)

PREFACE The current design criteria for cold-formed steel members published by the American Iron and Steel Institute (1986,1991) do not provide sufficient information for the design of web elements with openings. The primary objective of this investigation was to study the structural behavior of cold-formed steel C-sections with web openings. This study deals with the structural behavior of beam webs subjected to bending moment, shear force and combined bending moment and shear force. This report presents a summary of experimental study and findings of analytical results. The test results indicate that the current AISI Specification does not account for the …

Tensile And Bearing Capacities Of Bolted Connections, Jeffrey L. Carril, Roger A. Laboube, Wei-Wen Yu

CCFSS Library (1939 - present)

PREFACE Experimental studies were preformed to investigate the tensile capacity, bearing capacity and the interaction of tension and bearing capacities of flat sheet cold-formed steel bolted connections. The effect of bolt hole deformation on the bearing capacity of bolted connections, was also investigated. In the experimental investigation, single shear flat sheet connections were investigated for single bolt and multiple bolt configurations. The intent of this investigation was to compare the current AISI and AISC Specifications for the nominal bearing and tensile capacities and to develop appropriate serviceability design criteria. A review and evaluation of past research on the tensile and …

Structural Behavior Of Perforated Web Elements Of Cold-Formed Steel Flexural Members Subjected To Web Crippling And A Combination Of Web Crippling And Bending, James E. Langan, Roger A. Laboube, Wei-Wen Yu

CCFSS Library (1939 - present)

PREFACE A study of structural behavior was conducted and design equations were developed that account for the degradation in web crippling capacity caused by web openings for single web cold-formed steel flexural members. The sections were subjected to a concentrated load applied to one flange. The load application satisfied the AISI definition for either End-One-Flange or Interior-One-Flange loading. The research findings enable the current design provisions for sections without web openings to be modified by a reduction factor equation to obtain the web crippling capacity for sections with web openings. The modified capacity is considered for the web crippling capacity …

Ccfss Technical Bulletin February 1994, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News February 1994, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Ccfss Technical Bulletin August 1993, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News August 1993, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

An Energy Approach To Seismic Analysis And Design Of Secondary System, Genda Chen, Tsuteh Soong

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The dynamic analysis and design of secondary systems have been extensively studied over the last two decades, resulting in a better understanding of their general dynamic characteristics. One of the current challenges for researchers is to develop simple yet accurate procedures incorporating these research results and transfer them into the development of practical design and performance evaluation procedures. This is the basic thrust of this report.

Statistical energy analysis has been proven to be a powerful tool in the dynamic analysis of complex systems involving interaction effect between acoustic field and structure. In this report, such a tool is systematically …

Design Of Automotive Structural Components Using High Strength Sheet Steels Effect Of Strain Rate On The Structural Strength And Crushing Behavior Of Cold-Formed Steel Stub Columns, Chi-Ling Pan, Wei-Wen Yu

CCFSS Library (1939 - present)

INTRODUCTION In the past, a considerable amount of theoretical and experimental research has been undertaken to study material properties and the behavior of structures under dynamic loads and impact loads. For the purpose of investigating the structural behavior and strength of cold-formed steel members under dynamic loads, a research project was conducted at the University of Missouri-Rolla from January 1988 through December 1991 to study the effect of strain rate on mechanical properties of sheet steels and the structural behavior and strength of cold-formed steel members. The test results of material properties, stub columns, and beams with evaluations were summarized …

Preliminary Design Guide For Cold-Formed Steel C- And Z-Members, Committee On Specifications For The Design Of Cold-Formed Steel Structural Members

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Assessment Of 1991 Nehrp Provisions For Nonstructural Components And Recommended Revisions, Tsuteh Soong, Genda Chen, Z. Wu, R. H. Zhang, M. Grigoriu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

As one part of the 1994 update effort of the 1991 NEHRP provisions, the seismic design force formulas for nonstructural components as they exist in the 1991 provisions are critically assessed and some of their shortcomings are identified. Various levels of improvements to these formulas are then presented which, on the one hand, preserve the equivalent lateral force format for design applicability and, on the other, correct some of the deficiencies on the basis of analyses, experimental results and observation data from past earthquakes.

Based on different interpretations of the component seismic coefficients as well as different degrees of simplicity …

Ccfss Special Edition Technical Bulletin February 1993, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News February 1993, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Flexural Behavior Of Web Elements With Openings, Roger A. Laboube, Wei-Wen Yu, Ming-Yang Shan

CCFSS Library (1939 - present)

No abstract provided.

Simulation De L'Interaction Entre Le Voilement Local Et Les Modes Globaux D'Instabilite Des Profils A Froid Par Une Combinaison De La Methode Des Largeurs Effectives Et De L'Element Fini Non-Lineaire De Poutre Spatiale, Luiz Felippe Estrella Jr.

CCFSS Library (1939 - present)

The objective of this thesis is the study of the stability of cold-formed thin-walled steel members. The interaction between global instability and local buckling of the profile walls has a reducing effect on the collapse load. The aim is to develop a numerical tool able to predict not only the collapse load, but also the equilibrium path. With this aim in view, the non-linear spatial beam tinite element recently developed by Vincent de Ville in Liege University was chosen for this purpose. The steel member is considered as an association of flat plates and corners. Local buckling is modeled by …

Design Of Automotive Structural Components Using High Strength Sheet Steels Influence Of Strain Rate On The Mechanical Properties Of Sheet Steels And Structural Performance Of Cold-Formed Steel Members, Chi-Ling Pan, Wei-Wen Yu

CCFSS Library (1939 - present)

The current design criteria for effective design width being used in the AISI Automotive Steel Design Manual 1 for the design of cold-formed steel members are based on tests under static loading condition. The primary objective of this investigation was to study the validity of these effective design width formulas for members subjected to dynamic loads. This report presents a detailed description of an experimental study. Selected steels with nominal yield strengths ranging from 25 ksi to 100 ksi were uniaxially tested under different strain rates. In order to study the structural behavior and strength of cold-formed steel members having …

Tests Of Profiled Steel Decks With V-Stiffeners, E. S. Bernard, Russell Q. Bridge, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The size and position of intermediate stiffeners in the compression flanges of thin-walled profiled steel decks exerts a strong influence on the dominant buckling mode of the flange. The ability of the deck to provide both high load carrying capacity before the onset of elastic buckling and a high ultimate load capacity may therefore be affected. A programme of tests to determine the effectiveness of intermediate stiffeners in controlling buckling modes has been undertaken. A series of specimens were loaded in pure bending resulting in various buckling waveforms prior to ultimate failure through a plastic collapse mechanism. All specimens were …

Flexural Capacity Of Discretely Braced C'S And Z'S, Thomas Sputo, Jack Haynes, Duane S. Ellifritt

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The American Iron and Steel Institute's Specification for the Design of Cold-Formed Steel Structural Members (1) presently requires that channel and zee flexural members, when not attached to sheathing, be braced against twist and lateral translation at the quarter-points of the span (Section D3.2.2). This provision first appeared in the Second Edition of the Specification in 1956, and has been there through all succeeding editions up through the 1989 Addendum. The newest formula for lateral buckling (part (a) of C3.1.2) is a more exact procedure for calculating lateral torsional buckling of a doubly, singly, or point symmetrical section than was …

Tests Of Continuous Purlins Under Downwards Loading, Michael Celeban, Chris Healy, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper describes a test program on purlin-sheeting systems for which the sheeting was screw fastened to the purlins. The test program simulates downwards loading. Z-section purlins were tested in three span continuous lapped configurations. The test purlins were supported by a range of bridging (bracing) members ranging from no bracing to one brace per span. The test results are compared with the design values computed using the Australian Cold-Formed Steel Structures Standard (AS1538-1988). The Australian Standard design is based on a flexural-torsional buckling analysis which may include the restraint from attached sheeting.

The Buckling Behaviour Of Hollow Flange Beams, Mahen Mahendran, T. J. Heidt

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A new cold formed structural section known as the hollow flange beam is currently under development in Australia. This section will have many applications, particularly in portal frame buildings. This paper discusses the lateral distortional buckling behaviour of the hollow flange beam.

Recent Research And Developments In Cold-Formed Steel Design And Construction, Wei-Wen Yu, Roger A. Laboube

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Unstiffened Elements - Some Interesting Features - Tests of Profiled Steel Decks with V-Stiffeners - Bending Strength of Beams with Non-Linear Analysis - Local and Distortional Buckling of Thin-Walled Beams - Design of C-Sections Against Deformational Lip Buckling - Lateral Buckling of Singly Symmetric Beams - Flexural Capacity of Discretely Braced C's and Z's - The Buckling Behaviour of Hollow Flange Beams - Experimental Investigations of I-Beams - Tests of Continuous Purlins Under Downwards Loading - Tests of Full-Scale Roofing Systems - Profiled Sheet Behaviour Under Concentrated Load - On Design of Profiled Sheets with Varying Cross Sections - Properties …

Stainless Steel Tubular Beams - Tests And Design, Gregory J. Hancock, Kim J. R. Rasmussen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper presents tests on square and circular stainless steel tubular beams. An important part of the test programme was to quantify the increase in bending strength resulting from cold-work during the fabrication process. Tension and compression tests on coupons cut from finished tubes were also included in the test programme. Stress-strain curves for shear were obtained using the coupon test results and the concept of affinity factors. A design method is proposed for stainless steel tubular beams. The method incorporates the increase in strength produced by the cold-rolling process and is validated by comparing it to the test strengths. …

Bending Strength Of Beams With Non-Linear Analysis, Pekka Salmi, Asko Talja

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Bending strengths of open cross-section beams cold-formed from high-strength steel (HSS) are determined with non-linear analysis. Two kinds of beams are studied. The short beams are for examining the bending resistance of cross-sections and the long beams for studing the lateral buckling of open sections. The beams are modelled with shell elements and non-linear FEM analyses are carried out to predict the strengths of the models. Both material and geometrical non-linearities are included in the analyses. The results are compared with experimental results.

Local And Distortional Buckling Of Thin-Walled Beams, Reynaud Serrette, Teoman Pekoz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Recent research has characterized the behavior of panel beams with laterally unsupported compression flanges as either a complex local buckling mode or an overall buckling mode. Tests have shown that the behavior of the unsupported flange and web is similar to that of lateral buckling, except, rotation is enforced along the axis of the web and the tension flange--a behavior which may be described as distortional buckling. In the work described here, an analytical expression is presented for computing the elastic distortional buckling stress based on a model which treats the web and compression flange as an elastically restrained beam. …

Lateral Buckling Of Singly Symmetric Beams, Teoman Pekoz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

General solutions for the elastic lateral buckling moment of singly symmetric sections are studied. The studies include the effect of the location of the load on the section as well as the effect of moment gradients on the lateral buckling moment. Design provisions are outlined for the case of moment gradients.

On Design Of Profiled Sheets With Varying Cross Sections, Laszlo Horvath, Miklos Nemeti, Bela Veroci

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A short review is given on the effective width concept and about its use for determining of the moment capacity of sheets. A modified method, taking into account the varying flexural rigidity along the spans, is described and illustrated on examples carried out on first -generation panels.

Influence Of Deformed Metal Decking Composite Floors To Beam-Column Connections, Y. Xiao, D. A. Nethercot, B. S. Choo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A series of tests designed to investigate the interaction of a variety of different steel beam to column connection details with a composite metal deck floor is described. The main emphasis is on assessing the connections' moment capacity, rotational stiffness and rotation capacity. The full details of the experimental behaviour of the flush end plate and partial depth end plate connections will be described in this paper. A simple method for moment capacity calculation based on the test results is proposed herein.

The Bi-Axial Behaviour Of Shear Connectors In Composite Slabs And Beams, Chris T. Duffy, David O'Leary, Michel Montourcy

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The use of composite beams which utilise steel beams together with a composite steel sheet/concrete floor slab is well developed. Many forms of steel profile are used and the form of attachment to the steel beam is generally by welded shear studs or shot-fired shear connectors. The design procedures for these beams require a knowledge of the shear capacity of the connectors which may be influenced by the type of profile being used for the beam. This shear capacity is often deduced from information obtained from standard push-off tests which mayor may not include in the test set-up the actual …

Activities Of The Center For Cold-Formed Steel Structures, Wei-Wen Yu, Roger A. Laboube

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Center for Cold-Formed Steel Structures was established at the University of Missouri-Rolla in May 1990 under the sponsorship of the American Iron and Steel Institute and the University of Missouri-Rolla. This paper summarizes the activities performed at the Center during the past two years.