Structural Engineering Commons^™

Service Life And Life-Cycle Assessment Of Reinforced Concrete With Fly Ash And Limestone Calcined Clay Cement, Ravindra Gettu, Radhakrishna G. Pillai, Manu Santhanam, Sundar Rathnarajan, Anusha Basavaraj, Sripriya Raju, Yuvaraj Dhandapani

International Conference on Durability of Concrete Structures

Environmental impact due to the emission of carbon dioxide during concrete production can be taken care by reducing the clinker content in the cement. The clinker content can be reduced by replacing it with fly ash and limestone calcined clay. Such systems can have a potential to exhibit enhanced durability/service life when exposed to chloride and carbon dioxide. However, estimating probabilistic service life of concretes with such alternative binder systems is difficult due to the lack of quantitative estimates of the input parameters such as chloride diffusion coefficient (D_Cl), ageing coefficient (m), carbonation coefficient (K_CO2), and …

Improving The Sustainability Of The Built Environment By Training Its Workforce In More Efficient And Greener Ways Of Designing And Constructing Through The Horizon2020 Bimcert Project, Barry Mcauley, Avril Behan

Conference papers

The construction industry consumes up to 50% of mineral resources excavated from nature, generates about 33% of CO2 present in the atmosphere and is responsible for 40% of total global energy through both construction and operation of buildings. The realisation that current pervasive construction practices now face globalization, sustainability, and environmental concerns, as well as ever-changing legislation requirements and new skills needed for the information age has resulted in technologies such as Building Information Modelling (BIM) becoming a key enabler in navigating these barriers. To assist in overcoming these barriers, a number of funding initiatives have been put in place …

From Roadmap To Implementation: Lessons For Ireland’S Digital Construction Programme, Barry Mcauley, Alan Hore, Roger West

Conference papers

As part of their Future of Construction initiative in 2018 the World Economic Forum published an action plan to accelerate Building Information Modelling adoption. The WEF report highlighted actions that companies, industry organisations and governments are advised to implement to accelerate BIM adoption and better capitalise on delivering better project outcomes. According the authors of the report BIM is seen as the centrepiece of the construction industry’s digital transformation, however they acknowledged that BIM adoption globally remain slow. Anecdotal experience would suggest that BIM usage in Ireland is also very low and that a similar initiative or an adaptation of …

Centres Of Excellence And Roadmaps For Digital Transition: Lessons For Ireland’S Construction Industry, Barry Mcauley, Alan Hore, Roger West

Conference papers

Like most sectors in today’s working world, construction businesses are challenged to work in an increasingly digitised world with sophisticated demands from intelligent clients. So much has been written about the inefficiencies of the construction industry, its fragmentation, lack of collaboration, low margins, adversarial pricing, poor productivity, financial fragility, lack of research and development, poor industry image and relatively weak use of digital solutions. The Irish government recognises the importance of digital innovation to address many of the challenges the construction industry faces. With recent high profile reports of escalating spend on signature public sector projects and weak productivity performance …

Workforce Development Symposiums For Uhpc, Brad Weldon, Craig Newtson, Grace Mcmurry, Leticia Davila

Data

Corresponding data set for Tran-SET Project No. 18TTNMS02. Abstract of the final report is stated below for reference:

"Ultra-high performance concrete (UHPC) is a cementitious material with a dense microstructure that contributes to high compressive strengths as well as enhanced durability properties. UHPC also possesses significant post-cracking strength and ductility due to the addition of fibers. These characteristics produce a material that provides advantages over conventional concrete; however, high costs attributed to materials and production, lack of industry familiarity and knowledge, and the absence of standardized design procedures have impeded its widespread use. To help disseminate knowledge on UHPC, two …

Augmented Reality Enhancing The Inspections Of Transportation Infrastructure: Research, Education, And Industry Implementation, Fernando Moreu, Chris Lippitt, Dilendra Maharjan, Marlon Aguero, Xinxing Yuan

Data

Corresponding data set for Tran-SET Project No. 18STUNM03. Abstract of the final report is stated below for reference:

"Transportation infrastructure needs continuous monitoring that is conducted by field inspectors regularly in the field. Currently, infrastructure inspectors climb, measure, and photograph structures annually to inform repair needs and prioritize decisions. In order to promote and accelerate early learner's expertise in decision-making capabilities during infrastructure inspections, this research project developed various software applications using augmented reality (AR) as an inspection tool for bridges and bridge management, more specifically. By objectively quantifying infrastructure field inspections, inspectors can make more accurate field assessments and …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Data

Corresponding data set for Tran-SET Project No. 18STTAM02. Abstract of the final report is stated below for reference:

"This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples …

A Comprehensive Framework For Life-Cycle Cost Assessment Of Reinforced Concrete Bridge Decks, Mohamed Soliman, Samir Ahmed, Ligang Shen

Publications

Various environmental and mechanical stressors cause deterioration of concrete bridge decks. Normal wear and tear, freeze and thaw cycles, and chloride penetration due to deicing salts can cause aggressive deterioration that usually require frequent interventions during the life-cycle of the bridge. These interventions include deck maintenance and repairs (e.g., application of sealers or overlay placement) as well as bridge deck replacement. The quantification of the life-cycle cost of bridge decks considering maintenance and repair activities represents a significant challenge facing local and state transportation agencies. The life-cycle maintenance activities not only increase the direct life-cycle cost of the bridge, but …

Turbulent Effects On Building Pressure Using A Two-Dimensional Finite Element Program, Jonese Woods

Civil Engineering Undergraduate Honors Theses

Much of the knowledge about building aerodynamics today was obtained from physical testing like wind tunnel testing. Physical testing is time-consuming and very expensive. As a result, computational methods like the finite element method are being explored for use in building aerodynamics. Despite several years of research, there is still not a clear understanding of the peak pressure on buildings due to turbulence. Many of the research thus far has focused on comparing different computational methods. However, much work is needed in understanding the capability of the individual methods. In this work, a two-dimensional finite element program is used to …

Reliability-Based Shear Rating Of Prestressed Concrete Bridge Girders Considering Capacity Adjustment Factor, Alaa I. Chehab, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

In this study, the reliability of prestressed concrete (PC) bridge girders in the shear rating process is quantified, where the use of a simple procedure to enhance the accuracy of shear capacity evaluation for rating is evaluated. It was found that the approximate methods used in code-based procedures to develop shear resistance used for reliability calibration of the AASHTO Bridge Design Specifications and the Manual for Bridge Evaluation result in larger discrepancies in reliability than previously assumed, as well as substantially conservative shear capacity evaluation in most cases. To examine the effects of using a more accurate shear rating process, …

Bridge Deck Delamination Segmentation Based On Aerial Thermography Through Regularized Grayscale Morphological Reconstruction And Gradient Statistics, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Environmental and surface texture-induced temperature variation across the bridge deck is a major source of errors in delamination detection through thermography. This type of external noise poises a significant challenge for conventional quantitative methods such as global thresholding and k-means clustering. An iterative top-down approach is proposed for delamination segmentation based on grayscale morphological reconstruction. A weight-decay function was used to regularize the reconstruction for regional maxima extraction. The mean and coefficient of variation of temperature gradient estimated from delamination boundaries were used for discrimination. The proposed approach was tested on a lab experiment and an in-service bridge deck. The …

Application Of Computational Tools To Spaghetti-Based Truss Bridge Design, Jin Xu, Jiliang Li, Nuri Zeytinoglu, Jinyuan Zhai

ASEE IL-IN Section Conference

Application of Computational Tools to Spaghetti-Based Truss Design

Statics and Strength of Materials are two foundational courses for Mechanical/Civil Engineering. In order to assist students in better understanding and applying concepts to a meaningful design task, SolidWorks and theoretical calculation were used for a spaghetti-bridge design contest with the constraints of given maximum weight and allowable support-material weight. As the first step of this iterative designing process, both extrude feature and structural member were introduced to model planar bridge trusses. Then SolidWorks’ Statics module was used to run FEA analysis of the structural performance in efforts to optimize the …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

Assessing Impact And Blast Resilience Of Polymer Coated Cementitious Materials, Murtaza Nalwala, Gabriel Nsengiyumva, Yong-Rak Kim

UCARE: Research Products

RESEARCH MOTIVATION The bridge piers are highly vulnerable to the impact and blast loads. The position in which they are constructed makes it difficult to install protective devices around them. By the current AASHTO standard, it is possible to under-design bridge piers for commercial vehicle impacts and other events such as blast.

OBJECTIVE To improve impact and blast resilience of bridge piers using polymeric coatings.

CONCLUSION Polymer coating of Portland cement concrete can be achieved with a good bonding. ü The polymeric coating seem to improve impact resilience of Portland cement concrete by increasing absorbed impact energy (i.e., area underneath …

Advancing Bridge Technology, Task 10: Statistical Analysis And Modeling Of Us Concrete Highway Bridge Deck Performance -- Internal Final Report, Omar Ghonima, Thomas Schumacher, Avinash Unnikrishnan, Adam Fleischhacker

Civil and Environmental Engineering Faculty Publications and Presentations

Concrete highway bridge deck repairs represent the highest expense associated with bridge maintenance cost. In order to optimize such activities and use the available monies effectively, a solid understanding of the parameters that affect the performance of concrete bridge decks is critical. The National Bridge Inventory (NBI), perhaps the single-most comprehensive source of bridge information, gathers data on more than 600,000 bridges in all fifty states, the District of Columbia, and the Commonwealth of Puerto Rico. Focusing on concrete highway bridge deck performance, this research developed a nationwide database based on NBI data and other critical parameters that were computed …

Evaluation And Development Of Cpt Based Pile Design In Nebraska Soils, Alex Silvey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Cone penetration testing (CPT) is a well established geotechnical subsurface investigation technique commonly used for site characterization and soil classification. The CPT gives real time end resistance, side friction, and pore pressure readings. Axially loaded piles also share these two resistance mechanisms, suggesting the cone can be considered similar to a miniature pile. This study focused on evaluating eight CPT methods prediction of pile bearing capacity. The Nebraska Department of Roads (NDOR) conducts dynamic load tests (PDA) of driven pile to verify pile capacity for bridge foundations. 91 comparisons of CPT logs and PDA data were evaluated. CPT prediction methods …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …

Solar And Rain Catching Canopy. Urban Oasis, Afolabi Ibitoye, Langston Clark, Elena Zimareva, Evan Banks, Alexander Aptekar

Publications and Research

The Urban Oasis is designed to work within existing “pocket parks” in New York City as a combined rainwater collector, personal electronics charging station and resting designation for New Yorkers. Intended to not only lessen the demand on the city power grid by using renewable energy to charge devices, the urban oasis is also intended to mitigate grey water overfill in New York’s combined sewer system and, in general, serve as a model for responsible environmental stewardship in urban areas.

The important technical aspects of the canopy specifically analyzed were:

a) how much rainwater could the canopy be expected to …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Multi-Point Vibration Measurement And Mode Magnification Of Civil Structures Using Video-Based Motion Processing, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Image-based vibration measurement has gained increased attentions in civil and construction communities. A recent video-based motion magnification method was developed to measure and visualize small structure motions. This new approach presents a potential for low-cost vibration measurement and mode shape identification. Pilot studies using this approach on simple rigid body structures were reported. Its validity on complex outdoor structures has not been investigated. In this study, a non-contact video-based approach for multi-point vibration measurement and mode magnification is introduced. The proposed approach can output a full-field vibration map that increases the efficiency of the current structural health monitoring (SHM) practice. …

When To Use Midwest Guardrail System (Mgs) W-Beam Guardrail, Katherine Smutzer

Purdue Road School

In this session we will discuss when MGS w-beam guardrail should be placed on state and local projects and review pertinent INDOT Design Memos released over the past year.

Beauchemin Residence, Hannah E. Rogers

Architectural Engineering

The following report details the structural engineering completed on the Beauchemin Residence, as well as the associated drawings, details, and special considerations. The Beauchemin Residence is an existing single story wood frame building on raised wood floor, located in the city of San Clemente. The scope of work includes calculations for a new roof, new walls (gravity & lateral), retrofit of the existing foundation, new foundation, and providing calculations. The process and progression of the structural design is documented, and correlated to the final product in the Appendix A & B.

Methodology For Load Rating Double-Tee Girder Bridges, Sandip Rimal

Electronic Theses and Dissertations

The most common type of bridge on South Dakota (SD) local roads is precast prestressed double-tee (DT) girders. More than 700 DT bridges are currently in-service in SD. Structural detailing, aging, traffic volume, and environmental conditions affect the structural performance, integrity, and capacity of DT bridges. When a bridge is affected by one or more of the aforementioned parameters, the estimation of the bridge safe live loads is necessary to ensure the safety of the traveling public and to prevent excessive bridge damage and collapse. Load rating of damaged bridges is challenging mainly because of a lack of information regarding …

Tire-Derived Geo-Cylinders And Polymer Products For Enhancing The Properties Of Base/Sub Base Materials In Pavement Systems, Justin Scott Smith

Graduate Theses, Dissertations, and Problem Reports (ETD)

As a critical part of the transportation network, pavements offer a safe means for vehicular traffic. Pavements are subjected to many forms of stress during their service life, and they are susceptible to environment related cracking and failures. Failures can be attributed to poor subgrade, freeze-thaw variations, and fatigue under repetitive axle loadings. Reinforcement products such as tire-derived geo-cylinders (TDGC) which make-up mechanical concrete and geo-polymers have been utilized in civil engineering practice, and this research aims to understand the potential life of tested pavement system components set at displacement limitations when reinforced with TDGCs and geo-polymers from exposure to …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

What Lessons Can Be Learned From The Delivery Of The First Building On The Grangegorman Campus Using Building Information Management (Bim)?, Pat O'Sullivan, Avril Behan

Conference papers

There is an acceptance that BIM, via data management, can be integrated with FM to reduce costs during the Operations and Maintenance stage of a project. However, what has not been documented is the ‘on the ground’ reality which can be reviewed as a lessons learnt exercise to improve the implementation of BIM FM for future projects. This case study sets out to explore the realities of a client’s adoption of BIM based upon the actual experience of the Greenway Hub. Rather than relying on anecdotal evidence the research was based upon the real practices and experiences of the Dublin …

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Libraries' Newsletters

No abstract provided.

On The Ramberg-Osgood Stress-Strain Model And Large Deformations Of Cantilever Beams, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this thesis the Ramberg-Osgood nonlinear model for describing the behavior of many different materials is investigated. A brief overview of the model as it is currently used in the literature is undertaken and several misunderstandings and possible pitfalls in its application is pointed out, especially as it pertains to more recent approaches to finding solutions involving the model. There is an investigation of the displacement of a cantilever beam under a combined loading consisting of a distributed load across the entire length of the beam and a point load at its end and new solutions to this problem are …

Building Information Modelling In Ireland 2017, Barry Mcauley, Alan Hore, Roger West

Reports

BIM is perhaps the most topical issue in construction throughout the world at present, as it is associated with solving so many of the present concerns in our industry.

Our lack of housing, shortage of skilled workers, poor document management, overrunning project budgets and sustainability challenges are just a few of the challenges that BIM promises to assist in solving.

The increasing importance of “digitisation” to modern construction and engineering businesses is becoming more apparent as more and more clients are explicitly asking for BIM in the design and delivery of new facilities and infrastructure.

This report provides a snapshot …

Shrinkage Cracking In Concrete Tilt-Up Construction, Stewart Hooks, Jack Robinson

Architectural Engineering

The purpose of this project is to investigate a particular, undesirable cracking pattern in concrete tilt-up panels that, until now, did not have a known definite cause. The cause of this cracking pattern is hypothesized to be due to shrinkage restraint of the concrete panels. The cracking under investigation occurs at the bottom corners of the Tilt-Up panels, suggesting that the base of the panel is restrained from shrinkage. This project models various components of Tilt-Up Construction that have potential for restraining the panels from shrinking. This project consists of the following main components.

The first aspect of this project …