Environmental Engineering Commons^™

Direct Potable Reuse Of Wastewater, Boyce Bethel

Chemical Engineering Undergraduate Honors Theses

Water is essential to our societies and mankind. Currently, 844 million people across the globe lack access to potable water. By 2025, it is projected that half of the world population will be in a region of water stress.⁵ The water crisis is often thought of as a problem limited to places that have always struggled to have clean water, but it is now affecting new areas such as the southwest United States. With increasing population demands and drought, the feasibility of direct potable reuse (DPR) of wastewater is being considered. According to an EPA report in 2017, there …

Sustainable Waste-To-Energy Technologies: Bioelectrochemical Systems, Rami Ziara, Bruce Dvorak, Jeyamkondan Subbiah

Department of Civil and Environmental Engineering: Faculty Publications

The food industry produces a large amount of waste and wastewater, of which most of the constituents are carbohydrates, proteins, lipids, and organic fibers. Therefore food wastes are highly biodegradable and energy rich. Bioelectrochemical systems (BESs) are systems that use microorganisms to biochemically catalyze complex substrates into useful energy products, in which the catalytic reactions take place on electrodes. Microbial fuel cells (MFCs) are a type of bioelectrochemical systems that oxidize substrates and generate electric current. Microbial electrolysis cells (MECs) are another type of bioelectrochemical systems that use an external power source to catalyze the substrate into by-products such as …

Molecular Biogeochemistry Of A Poor Fen, Zhimin Song

Dissertations, Master's Theses and Master's Reports

Variations in climate may rapidly change the carbon balance of peatlands and increase greenhouse gas emissions through accelerated decomposition of peat and dissolved organic matter (DOM). In this study, porewater samples were collected monthly from May to October in 2017 to study the effects of plant functional groups (PFGs) on DOM, dissolved inorganic and organic nitrogen through the season in a poor fen with replicate plots dominated by different PFGs in Nestoria, Michigan, USA (46.34˚N 88.16˚W). The composition of the peat porewater showed strong statistical significance with plot type and season.The observed PFG and season impact on the composition of …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Atomic Layer Deposition Prepared Nanostructured Materials For Various Catalytic Reactions, Xiaofeng Wang

Doctoral Dissertations

"Atomic layer deposition (ALD) has been widely used for thin film coating and metal nanoparticles (NPs) preparation. In this report, the applications of ALD prepared nanostructured materials in catalysis were examined.

Highly dispersed Pt monometallic catalysts with different substrates and multi-walled carbon nanotubes (MWCNTs) supported Pt-Co bimetallic catalysts were synthesized by ALD for selective hydrogenation of α, β-unsaturated aldehydes to unsaturated alcohols (UA). Pt/MWCNTs showed the highest selectivity of UA in selective hydrogenation of citral, as compared to Pt/SiO₂, Pt/ALD-Al₂O₃, and Pt/γ-Al₂O₃. After adding Co, the highest selectivity was achieved …

Multi-Scale Studies To Develop A Holistic Understanding Of Solid Fuel Combustion At Residential Scale, Sameer Patel

McKelvey School of Engineering Graduate Student Theses & Dissertations

Nearly 3 billion people rely on solid fuels for their cooking and heating needs, classifying them as “energy poor”. This poverty can be attributed to several factors, including a lack of resources (fuel), inefficient infrastructure (production and distribution), limited purchasing power (poverty), and ill-devised policies. Solid fuels, such as biomass, coal, and dung cakes, are burned in inefficient cookstoves. They generate products of incomplete combustion (PIC), such as CO, particulate matter (PM), and CH4, causing household air pollution (HAP) whose adverse impacts on both health and the environment have been well established.

HAP causes diseases such as chronic obstructive pulmonary …

Pollution Prevention In The Great Lakes Basin: Working With Pulp & Paper Manufacturers, Eugene Park

Journal of Environmental Sustainability

In response to growing concerns over persistent toxic substances in the Great Lakes, new initiatives are in place to address and mitigate pollutant loadings to these large natural waterbodies. With support from the U.S. Environmental Protection Agency and New York Department of Environmental Conservation, the New York State Pollution Prevention Institute (NYSP2I) worked with pulp & paper companies in the Great Lakes Basin in an effort to find solutions to reduce environmental impacts from this industry sector. Based on currently available EPA toolkits, NYSP2I developed and utilized an assessment tool called Lean, Energy, and Environment (LE2). Five different paper manufacturers …

The Control Of Water Contaminants Assisted By Natural Materials, Wen Zhao

USF Tampa Graduate Theses and Dissertations

Natural materials can be used to remove water contaminants by applying proper physical, chemical, and biological water treatment processes. This study involves using natural materials, as they are considered to be more environmentally benign and cost-effective than synthetic materials. This dissertation concentrates on monitoring five major water quality parameters—ammonia, fluoride, turbidity, pH, and fecal indicator bacteria (FIB) —in two major applications where clean water is needed. The focus is on meeting the water quality requirements for each contaminant. The overall objective of this study is to control the levels of ammonia in aquaculture wastewater, and adjust fluoride, turbidity, pH, and …

Diagenesis And Formation Stress In Fracture Conductivity Of Shaly Rocks; Experimental-Modelling Approach In Co2-Rock Interactions, Abiola Olukola Olabode

LSU Doctoral Dissertations

In large scale subsurface injection of carbon dioxide (CO₂) as obtainable in carbon sequestration programs and in environmentally friendly hydraulic fracturing processes (using supercritical CO₂), long term rock-fluid interaction can affect reservoir and seal rocks properties which are essential in monitoring the progress of these operations. The mineralogical components of sedimentary rocks are geochemically active particularly under enormous earth stresses, which generate high pressure and temperature conditions in the subsurface. While geomechanical properties such as rock stiffness, Poisson’s ratio and fracture geometry largely govern fluid flow characteristics in deep fractured formations, the effect of mineralization can …

Influence Of Activated Carbon Surface Oxygen Functionality On Elemental Mercury Adsorption From Aqueous Solution, Emily K. Faulconer, David W. Mazyck

Publications

Mercury (Hg), though naturally occurring, is a toxic element. Exposure to various forms of mercury can be harmful for humans and ecosystems. Mercury-contaminated wastewater can be treated using activated carbon to adsorb the mercury, allowing for safe discharge. Wet chemical oxidation of activated carbon was performed to enhanced surface oxygen functionality, with the objective of enhancing aqueous ionic (Hg(II)) and elemental (Hg(0)) mercury adsorption. Characterization of the modified carbons included nitrogen adsorption-desorption, elemental analysis, point of zero charge, and total acidity titration. The concentration and identity of the modifying reagent influenced the characteristics of the carbons, including the surface oxygen …

Sub 2 Nm Particle Characterization In Systems With Aerosol Formation And Growth, Yang Wang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Aerosol science and technology enable continual advances in material synthesis and atmospheric pollutant control. Among these advances, one important frontier is characterizing the initial stages of particle formation by real time measurement of particles below 2 nm in size. Sub 2 nm particles play important roles by acting as seeds for particle growth, ultimately determining the final properties of the generated particles. Tailoring nanoparticle properties requires a thorough understanding and precise control of the particle formation processes, which in turn requires characterizing nanoparticle formation from the initial stages. The knowledge on particle formation in early stages can also be applied …

Passive Solar Distillation Of Acid Rock Drainage, Stephanie Shreve, Luke Galuska, Anna Stoller, Alex Raney, Agustin Caceres, Caitlyn Chambers, Chris Graham, Devin Hazlett

Chemical Engineering Undergraduate Honors Theses

Arkansas Razorback Distillers (A.R.D.) has developed a passive solar distillation system for treating acid rock drainage (ARD) from legacy (i.e., abandoned) mines. The solar still addresses the need to reduce both the metal sulfate contaminants as well as the acidity of acid rock drainage. During the design phase, A.R.D. addressed the need for the system to be low cost, simple, and effective for general use as well as a specified location. To demonstrate the applicability of the solar still, A.R.D. used the Freeport McMoRan Inc. Copper Queen legacy mine in Bisbee, Arizona, as a base case scenario. The mine was …

Evaluation Of Phosphorous Removals By Biochar Supported Nano-Scale Zero-Valent Iron, Maria S. Rossetti

Chemical Engineering Undergraduate Honors Theses

This study evaluated the effectiveness of biochar-supported nano-scale zero-valent iron (nZVI/BC) in removing phosphorus (P) from water. Samples of nZVI/BC were prepared using aqueous nanoparticles synthesis techniques, and were mixed with a stock phosphorus solution. To determine P reductions water samples were tested for P content using the ascorbic acid method. This procedure was repeated for samples of stock P solution, zero-valent iron (ZVI), biochar, and ZVI/BC. nZVI/BC reduced P content by 86% whereas ZVI, biochar, and ZVI/BC removed 6%, -23%, and 17% respectively. This suggests that nZVI/BC has the potential to be an effective method of stormwater remediation.

Effect Of High Cationic Flocculant On Anaerobic Digestion Of Municipal Wastewater., Prathap D. John

Electronic Theses and Dissertations

Anaerobic digestion (AD) of municipal sludge is a widely used stabilization process at municipal wastewater treatment plants. It is highly effective in reducing sludge volume and produces methane gas which is used as fuel in the wastewater plant. Following digestion sludge is sent to a centrifuge to separate the solids from the liquids. Louisville MSD adds flocculent to material in the centrifuge to better coagulate the solids, thereby aiding in separation of the solids from the liquids. The potential for further AD, COD reduction, and methane generation of the liquid effluent from the centrifuge was unknown, particularly in regards to …

Quantifying Cyanide Inhibition Of Nitrification And Developing Cost-Effective Treatment Processes, Germano M. Salazar-Benites

Civil & Environmental Engineering Theses & Dissertations

All wastewater treatment plants that operate multiple hearth furnaces (MHF) and are required to nitrify must manage the inhibitory effects of free cyanide (HCN, CN-) in the scrubber return flows due to inhibitory impacts on nitrifying bacteria.

HRSD Boat Harbor Treatment Plant (BHTP) a 25 MGD facility consisting of primary and secondary treatment, employs an anoxic selector process for nitrification and partial denitrification and operates a MHF. There is a desire to improve TN removal performance at BHTP due to an annual mass-based bubble permit limit on a combined discharge from seven HRSD plants, and there are no discharge limitations …

Toxicological Differences Between Perfluoroalkyl Substances (Pfas) Isomers Using Developmental Biomarkers, Gabriel A. Cantu

Theses and Dissertations

Perfluoroalkyl substances (PFAS) are metabolically stable synthetic chemicals that have been manufactured for commercial and industrial purposes since the 1950s. PFAS possess surfactant properties that make them ideal to fight hydrocarbon fires and are therefore present in aqueous film forming foams (AFFF). Furthermore, AFFF may contain blends of both linear and branched PFAS isomers. Research suggests that branched PFAS isomers have greater relative placental transfer efficiencies than their linear counterpart, but few studies have evaluated their toxicity. Therefore, the sustained use of AFFF in the U.S. Air Force presents a risk of branched PFAS exposures in pregnant females. This study …

Remediating 1,4-Dioxane-Contaminated Water With Slow-Release Persulfate And Zerovalent Iron, Ann Kambhu, Megan Gren, Wei Tang, Steve D. Comfort, Clifford Harris

Nebraska Water Center: Faculty Publications

1,4-dioxane is an emerging contaminant that was used as a corrosion inhibitor with chlorinated solvents. Metal-activated persulfate can degrade dioxane but reaction kinetics have typically been characterized by a rapid decrease during the first 30 min followed by either a slower decrease or no further change (i.e., plateau). Our objective was to identify the factors responsible for this plateau and then determine if slow-release formulations of sodium persulfate and Fe⁰ could provide a more sustainable degradation treatment. We accomplished this by conducting batch experiments where Fe⁰-activated persulfate was used to treat dioxane. Treatment variables included the timing …

Tunable Nanocomposite Membranes For Water Remediation And Separations, Sebastián Hernández Sierra

Theses and Dissertations--Chemical and Materials Engineering

Nano-structured material fabrication using functionalized membranes with polyelectrolytes is a promising research field for water pollution, catalytic and mining applications. These responsive polymers react to external stimuli like temperature, pH, radiation, ionic strength or chemical composition. Such nanomaterials provide novel hybrid properties and can also be self-supported in addition to the membranes.

Polyelectrolytes (as hydrogels) have pH responsiveness. The hydrogel moieties gain or lose protons based on the pH, displaying swelling properties. These responsive materials can be exploited to synthesize metal nanoparticles in situ using their functional groups, or to immobilize other polyelectrolytes and biomolecules. Due to their properties, these …

Advanced Buffer Materials For Indoor Air Co₂ Control In Commercial Buildings, Pavithra Ethi Rajan

Masters Theses

"The following describes a novel passive approach to control the indoor CO₂ levels in enclosed spaces, primarily focusing on commercial buildings. Amine impregnated silica sorbents were identified as suitable candidates and synthesized; the amine loading ratio was varied to create a range of materials. These samples along with other commercial zeolite candidates have been tested over a range of CO₂ concentrations to determine the CO₂ adsorption capacity in laboratory systems and under simulated room conditions. The research work also focuses on the CO₂ desorption capacity of the candidate adsorbents. The desorption is allowed to occur gradually …

Chlorpyrifos Removal For Wastewater Reuse, Indran Kamalanathan

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply.¹ Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Study Of Poisoning Mechanism Of Hg And As On V2o5–Wo3/Tio2 Scr De-Nox Catalysts, Qingcai Liu, Ming Kong, Lu Yao, Shan Ren, Jian Yang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Nanoparticle Formation In The Flame Synthesis Of Multicomponent Nanostructured Materials For Clean Energy Applications, Jiaxi Fang

McKelvey School of Engineering Graduate Student Theses & Dissertations

This dissertation studies the initial stages of particle formation during the combustion synthesis of multicomponent nanomaterials. Combustion is commonly used for the production of nanomaterials at industrial scales and has advantages of high production rates, low waste generation, and scalability. However, there are limitations in being able to apply this synthesis approach to more advanced multicomponent systems. Gas to particle conversion in flames occurs through precursor decomposition, collisional growth, coagulation, condensation, and sintering. There is a fundamental gap in knowledge on the initial stages of particle formation in flames below 2nm due to measurement difficulties and instrumentation limitations. Using a …

Crumpled Graphene Oxide: Aerosol Synthesis And Environmental Applications, Yi Jiang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Environmental technologies, such as for water treatment, have advanced significantly due to the rapid expansion and application of nanoscale material science and engineering. In particular, two-dimensional graphene oxide (GO), has demonstrated considerable potential for advancing and even revolutionizing some of these technologies, such as engineered photocatalysts and membranes. To realize such potential, an industrially scalable process is needed to produce monomeric and aggregation-resistant GO nanostructures/composites, in addition to new knowledge of material properties, behavior, and performance within an environmental context.

Research presented in this thesis addresses both scientific and engineering gaps through the development of a simple, yet robust aerosol-based …

Nanostructured Thin Film Synthesis By Aerosol Chemical Vapor Deposition For Energy Storage Applications, Tandeep Singh Chadha

McKelvey School of Engineering Graduate Student Theses & Dissertations

Renewable energy sources offer a viable solution to the growing energy demand while mitigating concerns for greenhouse gas emissions and climate change. This has led to a tremendous momentum towards solar and wind-based energy harvesting technologies driving efficiencies higher and costs lower. However, the intermittent nature of these energy sources necessitates energy storage technologies, which remain the Achilles heel in meeting the renewable energy goals. This dissertation focusses on two approaches for addressing the needs of energy storage: first, targeting direct solar to fuel conversion via photoelectrochemical water-splitting and second, improving the performance of current rechargeable batteries by developing new …

Modeling, Simulation, And Analysis Of Lithium-Ion Batteries For Grid-Scale Applications, Matthew Thomas Lawder

McKelvey School of Engineering Graduate Student Theses & Dissertations

Lithium-ion batteries have become universally present in daily life, being used across a wide range of portable consumer electronics. These batteries are advantageous compared to other forms of energy storage due to their high energy density and long cycle life. These characteristics make lithium-ion batteries advantageous for many new and developing applications that require large scale energy storage such as electric vehicles and the utility grid. Typical uses for lithium-ion batteries require consistent cycling patterns that are predictable and easy to approximate across all uses, but new large scale applications will have much more dynamic demands. The cycling patterns for …

Nanofiltration Rejection Of Contaminants Of Emerging Concern From Municipal Water Resource Recovery Facility Secondary Effluents For Potable Reuse Applications, Steven Michael Jones

Graduate Theses and Dissertations

As reuse of municipal water resource recovery facility (WRRF) effluent becomes vital to augment diminishing fresh drinking water resources, concern exists that conventional barriers may prove deficient and the upcycling of contaminants of emerging concern (CECs) could prove harmful to human health and aquatic species if more effective and robust treatment barriers are not in place.

There are no federal Safe Drinking Water Act (SDWA) regulations in place specifically for direct potable reuse (DPR) of WRRF effluent. Out of necessity, some states are developing their own DPR reuse regulations. Currently, reverse osmosis (RO) is the default full advanced treatment (FAT) …

Removal Of Endocrine Disrupting Compounds From Secondary Municipal Wastewater, Dustin R. Resz

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply.1 Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). Many …

Werc Task #1 - Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Jonathan A. Shumaker

Chemical Engineering Undergraduate Honors Theses

A design of a method for calculating the efficiency and particulate matter emission rates was developed for use on wood stoves. The project was completed for the WERC competition which is an international design contest. The prevalence of wood burning as a form of heating, current EPA regulations, and current market conditions were major factors in forming the necessity of this testing method. Design was not limited to outlining the design specifications, the apparatus was built and run. Optimization of the method continued until completion of the project. If the method would continue to be improved then it would be …