Construction Engineering and Management Commons^™

Preliminary Investigation Into The Rate Of Carbonation Of Concrete Blocks Under Normal Production Yard Conditions, Aimee Byrne, Eanna Nolan

Conference papers

The release of CO2 from calcination during the manufacture of cement can be partially or fully offset by the CO2 it naturally absorbs during its lifetime. This paper reports results from a preliminary investigation into the rate of carbonation in concrete blocks stacked in a production yard over a period of 6 months. The blocks were stacked in a normal manner under natural exposure conditions. Carbonation progress was determined by splitting the blocks and spraying the freshly exposed surface with a phenolphthalein solution at intervals over the test period. It was found that the rate of the carbonation front progression …

Bridge End Settlement Evaluation And Prediction, Jiwen Zhang

Theses and Dissertations--Civil Engineering

A bridge approach is usually built to provide a smooth and safe transition for vehicles from the roadway pavement to the bridge structure. However, differential settlement between the roadway pavement resting on embankment fill and the bridge abutment built on more rigid foundation often creates a bump in the roadway. Previous work examined this issue at a microscopic level and presented new methods for eliminating or minimizing the effects at specific locations.

This research studies the problem at a macroscopic level by determining methods to predict settlement severity to assist designers in developing remediation plans during project development to minimize …

Thermal Envelope Analysis Of Local Authority Low Rise Housing Based On Stock Aggregation Theory Using A Remote Feature Extraction Technique., James Pittam

Theses

Understanding the buildings thermal envelope is paramount to analysing existing problems which facilitate cold bridging and low surface temperatures. As no detailed housing stock database is in existence in Ireland which describes the geometrical configuration of the existing housing stock, and to create one would be a major challenge, this research set out to develop a high speed remote cataloguing and geometrical data extraction methodology to build such a database. Replacing traditional measurement methods with a remote method allows for the rapid extraction of fagade information. A remote surveying process is proposed named, the Virtual Survey Method, for the classification …

Object Detection For Agricultural And Construction Environments Using An Ultrasonic Sensor, Joseph S. Dvorak, Marvin L. Stone, Kelvin P. Self

Biosystems and Agricultural Engineering Faculty Publications

This study tested an ultrasonic sensor‘s ability to detect several objects commonly encountered in outdoor agricultural or construction environments: a water jug, a sheet of oriented strand board (OSB), a metal fence post, a human model, a wooden fence post, a Dracaena plant, a juniper plant, and a dog model. Tests were performed with each target object at distances from 0.01 to 3 m. Five tests were performed with each object at each location, and the sensor‘s ability to detect the object during each test was categorized as "undetected," "intermittent," "incorrect distance," "good." Rigid objects that presented a larger surface …

Forecasting Long Term Highway Staffing Requirements For State Transportation Agencies, Ying Li

Theses and Dissertations--Civil Engineering

The transportation system is vital to the nation’s economic growth and stability, as it provides mobility for commuters while supporting the United States’ ability to compete in an increasingly competitive global economy. State Transportation Agencies across the country continue to face many challenges to repair and enhance highway infrastructure to meet the rapid increasing transportation needs. One of these challenges is maintaining an adequate and efficient agency staff. In order to effectively plan for future staffing levels, State Transportation Agencies need a method for forecasting long term staffing requirements. However, current methods in use cannot function without well-defined projects and …

Flood Damage And Shutdown Times For Industrial Process Facilities, Matthew Lane Flynn

LSU Master's Theses

The vulnerability of the Gulf Coast to inundation poses a real threat to both national security and the regional economy due to the concentration of the nation’s energy infrastructure throughout the waterways of the southeastern United States’ waterways. Mitigation efforts thus far have been qualitative and fail to provide raw, quantitative data to aid in the successful management of flooding liabilities. This paper proposes a novel approach to analyzing infrastructure susceptibility by means of a component-based approach to consequences posed by water-borne incursions. Systems are simplified to collections of components, each with a lowest-member elevation, thereby identifying the benchmark for …

Identification Of Key Performance Tasks To Demonstrate The Benefit Of Introducing The Facilities Manager At An Early Stage In The Building Information Modelling Process On Public Sector Projects In Ireland., Barry Mcauley

Doctoral

Modelling (BIM) governed process was investigated in this thesis. Governments are now seeking a more rewarding methodology in the management and procurement of public sector building assets. This has seen an integrated focus by International Governments on BIM as a partial solution in both managing and procuring public sector building assets. Despite BIM bringing the Facility Manager closer to project conceptualisation, there was still a reluctance and a lack of perceived benefits of having them involved earlier in the design phase. There remains a lack of clear evidence on what improved contribution the Facilities Manager can provide. This thesis provides …

Single-Family Housing Construction Cost In The Greater Baton Rouge Area, Justin Pierce Estes

LSU Master's Theses

Most research focused on housing costs has noted a paucity of empirical cost data for residential construction, and researchers have suggested that collecting these data for individual metropolitan areas is ideal. The goal of this study is to obtain these data and compare them to national average sources to determine how well national data represent local costs. Data collection included obtaining prices from big box stores and through a survey of local Baton Rouge residential contractors for material, square foot and assembly costs for the major components of a house (i.e. foundation, wall, roof). From the material cost data evaluated, …

A Sustainability-Based Project Selection Algorithm: Socio-Technical-Economic Project Selection (Steps) Algorithm, Bharathi Bhattu

Dissertations, Master's Theses and Master's Reports

Multi-dimensional aspects play a vital role in the task of project-decision making. Environmental effects are to be considered in addition to other technical and non-technical aspects in order to avoid undue environmental damage. This current work introduces a new decision-making algorithm (Socio-Technical-Economic Project Selection or STEPS) that is demonstrated with the use of RCA (recycled concrete aggregate) as riprap for slope stabilization and erosion control which leaches chemical arsenic when in contact with water. Arsenic has long been recognized for its lethal properties. The main intention of introducing this new algorithm is to use sustainability concepts of social, technical, and …

Elasto-Plastic Transient Dynamic Response Of Tubular Section Steel Cantilever Beam Under Impact Loading, Alial Aloosi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of an experimental and theoretical investigation into the loadcarrying capacity of Fiber Reinforced Polymer (FRP) I-section beams subjected to four-point loading. The overall lateral-torsional buckling, web and flange local buckling as well as material rupture load estimates are also made using the American Society of Civil Engineers#x2019; Load and Resistance Factor Design (ASCELRFD) Pre-Standard for FRP Structures. Lateral-torsional buckling failure mode is found to govern for each of the beams studied. The study also revealed that the height of applied loads relative to the shear center has a very significant influence on lateral-torsional buckling load …

Ae 2250: Construction Graphics And Design—A Peer Review Of Teaching Project Benchmark Portfolio, Asregedew Woldesenbet

UNL Faculty Course Portfolios

This course portfolio designs and documents AE 2250 (Construction Design and Graphics) course that is taught in Spring 2016 at UNL's College of Engineering under the Durham School of Architectural Engineering and Construction program. The course is intended to introduce BIM (Building Information Modeling) to architectural engineering, construction engineering, construction management and civil engineering students ranging from freshman to juniors. This course portfolio documents the challenges associated with delivering this course, tailors the course objectives, activities and tracking measures to meet the course objectives throughout the semester. This portfolio uses quantitative and qualitative measures to track student performances and learning …

Lateral-Torsional Buckling Of Frp I-Section Beams, Mojtaba B. Sirjani, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of an experimental and theoretical investigation into the load-carrying capacity of Fiber Reinforced Polymer (FRP) I-section beams subjected to four-point loading. The overall lateral-torsional buckling, web and flange local buckling as well as material rupture load estimates are also made using the American Society of Civil Engineers Load and Resistance Factor Design (ASCE-LRFD) Pre-Standard for FRP Structures. Lateral-torsional buckling failure mode is found to govern for each of the beams studied. The study also revealed that the height of applied loads relative to the shear center has a very significant influence on lateral-torsional buckling load …

Enhancing Project Management With Lean World Class Manufacturing In Construction, Jacob Randles

College of Graduate Studies: Theses & Dissertations

In construction, the goal of commercial projects is to turn a profit. This is achieved by minimizing inputs and maximizing outputs while building a product that meets the customer’s perception of value. Value is determined through pre-negotiated specifications, plans, and material quality. Even in U.S. military construction, the unit executing the construction wants to complete the task on time and on budget, which can be difficult to do. Studies on project completion showcase a surprisingly high rate of failure in reaching the aforementioned “on time, on budget” goal. It is important to understand the nuances and details of U.S. Army …

Expedient Airfield Runway Repair Using Folded Fiberglass Mat, Christopher Y. Tuan, Willaim C. Dass

Department of Civil and Environmental Engineering: Faculty Publications

For expedient airfield runway repair, the US Air Force has developed a folded fiberglass mat to cover craters repaired with a well-compacted granular base material. The objective of this study was to evaluate the adequacy of using polymer plugs to anchor the mat to a repaired asphalt pavement for heavy aircraft operations. The effort consisted of materials testing, field experiments and analytical modeling. An 89,800-kg (198,000-pound) load cart having the footprint of a single C-5 main gear was pulled on a mat with wheels locked to simulate full braking forces. Anchor bushings were instrumented to measure anchor loads. A simplified …

Bs News January/February

Building Services Engineering

No abstract provided.