Civil Engineering Commons^™

Development Of A Design Based Intersection Safety Performance Evaluation Tool, Adam J. Kirk

Theses and Dissertations--Civil Engineering

The purpose of this research is to develop an intersection safety evaluation tool that is capable of assisting designers and planners in the assessment of alternative intersection designs. A conflict exposure model utilizing design hour volumes, intersection configuration and traffic control measures is proposed to achieve this goal. This approach makes use of data typically available for preliminary intersection design. The research goes beyond existing safety performance models which only examine non-directional average daily traffic (ADT) or practices which only account for the geometric and lane configuration of an intersection, such as conflict point analysis.

Conflict prediction models are developed …

Assessing The Structural, Driver And Economic Impacts Of Traffic Pole Mounted Wind Power Generator And Solar Panel Hybrid System, Anuj Sharma Ph.D., Justice Appiah Ph.D., Scott K. Rosenbaugh

Mid-America Transportation Center: Final Reports and Technical Briefs

This project evaluates the physical and economic feasibility of using existing traffic infrastructure to mount wind power generators. Some possible places to mount a light weight wind generator and solar panel hybrid system are: i) Traffic signal pole and ii) Street Light pole. Traffic signal poles can themselves have multiple designs depending on type of mount (mast arm vs. span wire) and the width of the intersection (load carried) etc. The close proximity of street light poles and traffic signal poles to the traffic cabinets, which can be used for storing the battery banks, make them good candidates to mount …

Truck Safety At Highway-Rail Grade Crossings, Aemal Khattak, Miao Gao

Mid-America Transportation Center: Final Reports and Technical Briefs

Safety at highway-rail grade crossings (HRGC) is a major concern for different agencies because increasing highway and rail traffic presents a greater risk of crashes at these locations. In 2008, there were 2,391 crashes and 523 fatalities reported at grade crossings across the U.S. Of these, 187 crashes were reported in Nebraska, including 35 involving trucks with trailers and 10 involving trucks only. At gated crossings, gate-related violations by truck drivers are a primary cause of collisions between trains and trucks. The objectives of this research were to report on the frequency and type of gate violations by truck drivers …

Head Ejection During Barrier Impacts, Scott K. Rosenbaugh, Ronald K. Faller, Dean L. Sicking

Department of Civil and Environmental Engineering: Faculty Publications

During oblique vehicular impacts with longitudinal barriers, an occupant’s head is often ejected out of a side window. When this occurs, the occupant’s head can contact the barrier or an object attached thereto. This impact event, often termed head slap, normally produces a serious injury or fatality. Roadside barriers and any attached hardware should be designed with sufficient offset at the top to preclude head slap for most impact conditions. The goal of this study was to identify the extent of head ejection that can be expected during high-speed crashes with longitudinal barriers. High-speed videos of full-scale vehicle crash tests …

Safety Evaluation Of Work Zone Practices In Utah, Tomás Ernesto Lindheimer

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Work zones present a risk to drivers and to personnel constructing the roadway. In 2005 work zones accounted for 2.5% of fatalities nationwide, 3.5% for the state of Utah. The goal of this research is to make work zones safer by quantifying the risk that they present to drivers. The approach of this research has been to review part 6 of the Manual of Uniform Traffic Control Devices (MUTCD) and compare the differences from the 2003 and 2009 editions, conduct field studies of Utah work zones, and develop a tool for measuring risk in work zones. In the 2009 MUTCD …

The Feasibility Of Using An Instrumented Vehicle Equipped With Inertial Navigation Guidence System To Collect Roadway Grade And Cross-Slope Data For Safety Analysis, Cyle Rhoades

All Theses

In 2005, the Federal Highway Administration (FHWA) requested the development for the initial version of the Model Minimum Inventory of Roadway Elements (MIRE). MIRE is a roadway inventory and traffic data collection data program that has a strong focus on improving the decision process in safety programs. MIRE is not a mandatory state program, but is strongly recommended based on its potential advantages. Some of the data required for MIRE was previously collected as a result of the requirements set from the Highway Performance Monitoring System (HPMS).
This thesis concentrates on the feasibility of determining as-built grade and cross-slope data …

Analyzing Motorists’ Responses To Temporary Signage In Highway Work Zones, Yong Bai, Kris Finger, Yue Li

Civil and Environmental Engineering Faculty Research and Publications

For decades, the importance of highway work zone safety has increased considerably with the continual increase in the number of highway work zones present on highways for repairs and expansion. Rural work zones on two-lane highways are particularly hazardous and cause a significant safety concern due to the disruption of regular traffic flow. In this study, researchers determined motorists’ responses to warning signs in rural, two-lane highway work zones. The researchers divided vehicles into three classes (passenger car, truck, and semitrailer) and compared the mean change in speed of these classes based on three different sign setups: portable changeable message …

Developing A Sustainable Freight Transportation Framework With The Consideration Of Improving Safety And Minimizing Carbon Emissions, Margaret Rita Neff, Yong Bai, Steven Schrock, Thomas E. Mulinazzi

Mid-America Transportation Center: Final Reports and Technical Briefs

Despite the difficulties of the American economy in recent years the transportation sector continues to expand. Freight transportation alone has been projected to increase enormously even if the economy as a whole only manages a very moderate growth. Not only does freight transportation use a large percentage of resources but it contributes significantly to America’s share of carbon emissions and affects the safety of the transportation system and all its users. These problems are only expected to increase as the volume of freight transportation is already reaching the limit of the American transportation infrastructure’s capacity and demand continues to increase. …

Highway Work Zone Risk Factors And Their Impact On Crash Severity, Yingfeng Li, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

Numerous factors may contribute to high-severity crashes in highway work zones. Identifying these factors and then alleviating their impact is a challenging task that traffic engineers and researchers have to confront. In this study, the work zone risk factors that could increase the probability of causing fatalities when severe crashes occur were examined using a comprehensive approach. The researchers first identified the significant risk factors based on a screening process that incorporates both statistical analyses and empirical research findings. They then systematically investigated these factors using logistic regression and frequency analysis techniques. The severe crashes including the fatal crashes between …

Worker Injury Prevention Strategies, Carlos A. Ferreira-Diaz, Alma Torres-Zapata, Christopher A. Nanovic, Dulcy M. Abraham

JTRP Technical Reports

As the trend of increased highway construction and/or rehabilitation continues to grow, the public often demands that delays in work zones be kept to a minimum. Thus, the flow of traffic through the construction zone must be maintained while performing pavement maintenance/ repair/ reconstruction activities. At the same time, the safety of personnel and property in highway construction work zones must be ensured. Three types of risks are encountered by construction and maintenance workers in construction workzones: (a) risks due to underprotection or lack of protection against potential hazards (including lack of hearing protection, eye protection, respiratory protection); (b) effect …

Effectiveness Of Temporary Traffic Control Measures In Highway Work Zones, Yingfeng Li, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

In the United States, hundreds of people lose their lives each year and many more are injured due to vehicle crashes in the work zones. Over the years, temporary traffic control (TCC) measures have been developed and deployed in work zones. To continuously improve the safety, there is a need to identify the traffic control deficiencies in work zones by evaluating the effectiveness of existing TTC measures based on the real crash cases. In this study, researchers evaluated the effectiveness of several commonly used TTC methods using logistic regression techniques and various significance test methods including likelihood ratio test, score …

Analyses Of Crash Occurence And Injury Severities On Multi Lane Highways Using Machine Learning Algorithms, Abhishek Das

Electronic Theses and Dissertations

Reduction of crash occurrence on the various roadway locations (mid-block segments; signalized intersections; un-signalized intersections) and the mitigation of injury severity in the event of a crash are the major concerns of transportation safety engineers. Multi lane arterial roadways (excluding freeways and expressways) account for forty-three percent of fatal crashes in the state of Florida. Significant contributing causes fall under the broad categories of aggressive driver behavior; adverse weather and environmental conditions; and roadway geometric and traffic factors. The objective of this research was the implementation of innovative, state-of-the-art analytical methods to identify the contributing factors for crashes and injury …

Comprehensive Analytical Investigation Of The Safety Of Unsignalized Intersections, Kirolos Haleem

Electronic Theses and Dissertations

According to documented statistics, intersections are among the most hazardous locations on roadway systems. Many studies have extensively analyzed safety of signalized intersections, but did not put their major focus on the most frequent type of intersections, unsignalized intersections. Unsignalized intersections are those intersections with stop control, yield control and no traffic control. Unsignalized intersections can be differentiated from their signalized counterparts in that their operational functions take place without the presence of a traffic signal. In this dissertation, multiple approaches of analyzing safety at unsignalized intersections were conducted. This was investigated in this study by analyzing total crashes, the …

Investigation Of The Effective Use Of Warning Lights On Indiana Department Of Transportation (Indot) Vehicles And Equipment, Bob Mccullouch, Brandon Stevens

JTRP Technical Reports

This study was requested by INDOT to determine if current lighting packages used on INDOT maintenance vehicles, specifically snow plow vehicles, can be improved with other commercially available products. Different light products were obtained from various vendors, mounted on INDOT vehicles, and visual comparisons were performed under various lighting and weather conditions by a team of observers. The comparison evaluations were performed revealing that other light packages, LED models for most options, were brighter and certain colors more visible. The preferred light models are recommended. These recommendations were forwarded to appropriate individuals that make these decisions at INDOT. Implementation is …

Comparison Of Characteristics Between Fatal And Injury Accidents In The Highway Construction Zones, Yingfeng Li, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

Highway construction zone safety has been a research focus in many countries for many decades. In the United States, regardless of the research efforts devoted, highway construction zones remain a serious safety concern for government agencies, legislatures, the highway industry, and the traveling public. In this study, the fatal and injury accidents between 1992 and 2004 in Kansas highway construction zones were examined systematically and their major characteristics were compared. The results showed significant differences between fatal and injury accidents in the construction zones. The researchers found that: (1) head-on was the dominant type for fatal accidents while rear-end was …

Characteristics Of Red Light Running Crashesin Florida, Dina Elnashar

Electronic Theses and Dissertations

Red light running is one of the main contributing factors of crashes in urban areas in Florida and the United States. Nationwide, according to preliminary estimates by the Federal Highway Administration (FHWA) 2001, there were nearly 218,000 red-light running crashes at intersections. These crashes resulted in as many as 181,000 injuries and 880 fatalities, and an economic loss estimated at $14 billion per year nationwide, According to the Community Traffic Safety Team Florida Coalition (A statewide traffic safety group) there were 9,348 crashes involving red-light running in Florida and 127 fatalities in 1999. This research study focused on studying the …

Risk Assessment Of Various Median Treatments Of Rural Interstates, Natalie M. Villwock, Nicolas Paul Blond, Andrzej P. Tarko

JTRP Technical Reports

This report presents results of a comprehensive study that evaluates the safety impacts of alternative median treatments on rural freeways. Extensive data were obtained from Indiana, Colorado, Illinois, Iowa, Missouri, New York, Ohio, Oregon, Washington, and Wisconsin. The studied median treatments include AASHTO-recommended treatments: depressed medians, depressed medians with high and lowtensioned cable barriers, and flush medians with concrete barriers. Other treatments used in the freeway design were also studied: medians with berms, sloped medians, and depressed medians with berms. Negative binomial models were developed to predict the frequency of crashes in three categories: single vehicle (SV), multiple vehicles same …

Intelligent Painting Process Planner For Robotic Bridge Painting, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

Due to increased government regulations on environment, health, and safety, the cost of on-site bridge painting has quadrupled over the past several years. The construction industry faces a great challenge in how to control the increased costs of bridge painting and meet the regulations at the same time. A possible solution to address this challenge is to develop a robotic bridge painting system. The development of the robotic system can be justified by the potential improvements in safety and productivity. This paper presents the development and testing of an Intelligent Painting Process Planner. The Planner, built based on bridge feature …

The Structural Reliability Of Bridges Subject To Time-Dependent Deterioration, Colin C. Caprani, C. Mcnally, E. J. O'Brien, A. Bordallo-Ruiz

Conference papers

The reliability of the structural performance of any given structure is affected by both in-service loading and material deterioration due to environmental attack. They must be evaluated at any given time in order to compute lifetime probability of failure. This paper presents an innovative methodology to derive the structure lifetime load effect due to existing traffic using a statistical tool known as Predictive Likelihood. Loss of resistance due to corrosion originated by chloride ingression is also taken into account. Finally the lifetime probability of failure is evaluated via the application of a time-discretization strategy.

Evaluating And Enhancing The Safety Of Nighttime Construction Projects, Dulcy M. Abraham, Julia Jensen Spadaccini, Beau Braxton Burgess, Lindsay Rae Miller, Vanessa Valentin

JTRP Technical Reports

The increased demand on the current highway system has caused transportation agencies to increase scheduling for nighttime work in order to alleviate daytime work zone congestion, especially during peak traffic hours. Although traffic congestion is reduced, safety in nighttime workzones remains a concern among both transportation agencies and contractors. According to the Federal Highway Administration (FHWA), approximately one-half of the fatalities that occurred in workzones nationwide occurred at night. These work zone statistics have received increased attention among agencies to evaluate planning and safety issues concerning the workers and the general public on nighttime workzones. Four separate, but interrelated research …

3m Personal Air Monitoring Systems, Purdue Ect Team

ECT Fact Sheets Archive

3M monitors are made to allow sample desorption directly in the monitor itself. The monitor comes with a snap-on elution cap that permits the desorbing solvent to be injected into the monitor. The solution is then poured into sample vials for analysis. 3M monitors use standard analytical methods: gas chromatography for the organic vapor monitor and ethylene oxide monitor, and colorimetry for the formaldehyde monitor.

Pipeman:Safety In Trenches, Purdue Ect Team

ECT Fact Sheets Archive

Even though heavy construction equipment such as a crane or backhoe excavator, is used to perform the task of pipe laying in the trench, workers are required to be inside the trench to guide the excavation, pipe laying, and final alignment. Work place safety has become a major concern in the construction industry over the past few decades, and trench cave-ins have caused serious and often fatal injuries to workers in the United States. The Construction Automation and Robotics Laboratory(CARL) at North Carolina State University has developed an alternative which involves advanced new technology: the prototype robotic excavation and pipe …

Behavior-Based Safety In Construction, Purdue Ect Team

ECT Fact Sheets Archive

Behavior-based safety approach that was introduced into the United States in 1930's and has been popular in manufacturing area since 1980's assumes that many of injuries and illnesses are the result of unsafe acts by workers. Behavior-based safety is a proactive approach to increasing safety in the workplace and in the community. It is based on sound, research-based, and behavioral practices, and are easy to use with minimal training.

Delmia Safework®Pro™ : Human Modeling, Purdue Ect Team

ECT Fact Sheets Archive

Manufacturers and designers strive to develop products that conform to all relevant Health and Safety standards and are "user-friendly" while still maximizing the productivity of their own workforce. Digital human modeling technology can assist a designer to determine the performance of people in the context of a workplace or a product before it exists and throughout its entire lifecycle. SAFEWORK’S accurate manikin has the highest number of Anthropometric Variables (104), Segments (99) and Degrees of Freedom (149). It also has fully articulated spine & hand models as well as joints with coupled range of motion. Moreover, it’s unique Multivariate Algorithm …

Cranium: Device For Improving Crane Productivity And Safety, Purdue Ect Team

ECT Fact Sheets Archive

Cranes are the most important pieces of equipment on many construction sites. CRANIUM is a video system designed to improve productivity and safety of crane operations by improving communications. A video camera mounted on the crane bottom transmits an image to the television monitor in the crane cab. The operator has a real-time picture of the loads and craftsmen that might otherwise be out of the direct line of sight.

Safe Excavation, Purdue Ect Team

ECT Fact Sheets Archive

Excavating with a backhoe or similar equipment has the potential risk of hitting an underground utility which could cause serious injuries and expensive damages. An electronic device that provides a real-time warning of the utility lines immediately ahead of the digging tool and provides an easily interpreted, real-time computer readout of the depth, location, and size buried metallic objects. Developed by Dr. Leonhard E. Bernold, it consists of an active metal detector search coil; a signal processing (control) unit; and a PC computer equipped with an analog-to-digital converter interface.

Driving Simulator Validation And Rear-End Crash Risk Analysis At A Signalised Intersection, Praveen Chilakapati

Electronic Theses and Dissertations

In recent years the use of advanced driving simulators has increased in the transportation engineering field especially in evaluating safety countermeasures. The driving simulator at UCF is a high fidelity simulator with six degrees of freedom. This research aims at validating the simulator in terms of speed and safety with the intention of using it as a test bed for high risk locations and to use it in developing traffic safety countermeasures. The Simulator replicates a real world signalized intersection (Alafaya trail (SR-434) and Colonial Drive (SR-50)). A total of sixty one subjects of age ranging from sixteen to sixty …

Safety Effects Of Traffic Signal Installations On State Road Intersections In Northeast Florida, Christopher Ledew

Electronic Theses and Dissertations

The purpose of this thesis is to explore how the installations of traffic signals affect crash experience at intersections, to identify those factors which help predict crashes after a signal is installed, and to develop a crash prediction model. It is the intent of this thesis to supplement the Manual on Uniform Traffic Control Devices Signal Warrant procedure and aid the traffic engineer in the signal installation decision making process. Crash data, as well as operational and geometric factors were examined for 32 state road intersections in the northeast Florida area before and after signal installation. Signal warrant studies were …

Stochastic Algorithm For Improved Operations At Isolated High Speed Intersections, Anuj Sharma, Darcy M. Bullock, Srinivas Peeta

Department of Civil and Environmental Engineering: Faculty Publications

The current practice of specifying simultaneous gap out logic at isolated high speed signalized intersections places constraints on the signal controller logic that cannot be satisfied under high congestion level. Further, it often results in degraded signal efficiency and dilemma zone protection. A stochastic approach is proposed in this paper with the objective of increasing safety and efficiency at these intersections.

Neural Network Trees And Simulation Databases: New Approaches For Signalized Intersection Crash Classification And Prediction, Piyush Nawathe

Electronic Theses and Dissertations

Intersection related crashes form a significant proportion of the crashes occurring on roadways. Many organizations such as the Federal Highway Administration (FHWA) and American Association of State Highway and Transportation Officials (AASHTO) are considering intersection safety improvement as one of their top priority areas. This study contributes to the area of safety of signalized intersections by identifying the traffic and geometric characteristics that affect the different types of crashes. The first phase of this thesis was to classify the crashes occurring at signalized intersections into rear-end, angle, turn and sideswipe crash types based on the traffic and geometric properties of …