Civil Engineering Commons^™

Fatigue Strength Of Steel Bridge Members With Intersecting Welds, David T. Delong, Mark D. Bowman

JTRP Technical Reports

The brittle fracture of the Hoan Bridge in December 2000 highlighted the fracture susceptibility of details containing intersecting welds in steel bridges. Though it is now known that details with intersecting welds should be avoided, many existing bridges in Indiana contain details with intersecting welds. Little experimental data on the fatigue performance of these details exists.

The purpose of this study was to evaluate the fatigue strength of several details commonly found in steel bridges in Indiana that contain intersecting welds. Large-scale experimental fatigue testing were performed using nine steel beams to study the behavior of three basic types of …

Data Analysis Of Utah's I-80 And I-215 Bridges - For The Use In The Development Of Accelerated Bridge Construction Standards, Erik S. Rosvall

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This study discusses five bridges on Utah's I-80 that were replaced in the summer of 2008 using Accelerated Bridge Construction methods. Each superstructure was built offsite and moved into place with the use of Self-Propelled Modular Transporters. The bridges were instrumented and monitored during the moving process to investigate the effects of moving an entire superstructure into place. Collected data was analyzed to find the level of stress each superstructure experienced during lifting, moving, and placement of each bridge.

The change in supporting conditions from when the superstructure was built to being transferred onto Self-Propelled Modular Transporters caused significant stress …

Ultimate Shear Capacity And Residual Prestress Force Of Full-Scale, Forty-One-Year-Old Prestressed-Concrete Girders, Parry Osborn

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The ultimate shear capacity of prestressed concrete beams is difficult to predict accurately, especially after being in service for an extended period of time. The Utah Department of Transportation asked researchers at Utah State University to experimentally determine the existing shear capacity of 41-year-old prestressed, decommissioned concrete bridge girders and then provide recommendations on how to increase that ultimate shear capacity. This thesis presents the research findings that relate to the existing shear capacity of the prestressed concrete girders.

Eight AASHTO Type II bridge girders were tested up to failure by applying external loads near the supports to determine their …

Site Specific Modelling Of Traffic Loading On Highway Bridges, Bernard Enright, Eugene J. Obrien

Conference papers

Accurate traffic loading models based on measured weigh-in-motion (WIM) data are essential for the accurate assessment of existing bridges. Much work has been published on the Monte Carlo simulation of single lanes of heavy vehicle traffic, and this can easily be extended to model the loading on bridges with two streams of traffic in opposing directions. However, a typical highway bridge will have multiple lanes in the same direction, and various types of correlation are evident in measured traffic, such as groups of very heavy vehicles travelling together and heavy vehicles being overtaken by lighter ones. These traffic patterns affect …

Characteristic Dynamic Increment For Extreme Traffic Loading Events On Short And Medium Span Highway Bridges, Eugene J. Obrien, Daniel Cantero, Bernard Enright, Arturo González

Articles

More accurate assessment of safety can prevent unnecessary repair or replacement of existing bridges which in turn can result in great cost savings at network level. The allowance for dynamics is a significant component of traffic loading in many bridges and is often unnecessarily conservative. Critical traffic loading scenarios are considered in this paper with a model that allows for vehicle-bridge interaction and takes into account the road surface condition. Characteristic dynamic allowance values are presented for the assessment of mid-span bending moment in a wide range of short to medium span bridges for bi-directional traffic.

Importance Of The Tail In Truck Weight Modeling For Bridge Assessment, Eugene J. Obrien, Bernard Enright, Abraham Getachew

Articles

To predict characteristic extreme traffic load effects, simulations are sometimes performed of bridge loading events. To generalize the truck weight data, statistical distributions are fitted to histograms of weight measurements. This paper is based on extensive WIM measurements from two European sites and shows the sensitivity of the characteristic traffic load effects to the fitting process. A semi-parametric fitting procedure is proposed: direct use of the measured histogram where there are sufficient data for this to be reliable and parametric fitting to a statistical distribution in the tail region where there are less data. Calculated characteristic load effects are shown …

A New Congested Traffic Load Model For Highway Bridges, Colin C. Caprani, Colm Carey, Bernard Enright

Conference papers

Long span highway bridges are critical components of any nation’s infrastructure. Therefore accurate assessment of highway bridge loading is essential, and it is well known that congested traffic governs load effect for such bridges. Current congestion models use conservative assumptions about traffic and inter-vehicle gaps. This research investigates congested traffic flow through the use of traffic microsimulation which has the ability to reproduce complex traffic phenomena based on driver interactions. A time series model has been developed to produce a speed time-series similar to the results of the microsimulation. The speed time-series from the new model, combined with the established …

The Influence Of Correlation On The Extreme Traffic Loading Of Bridges, Eugene J. Obrien, Bernard Enright, A. T. Dempsey

Conference papers

Accurate traffic loading models based on measured data are essential for the accurate assessment of existing bridges. There are well-established methods for the Monte Carlo simulation of single lanes of traffic, and this can easily be extended to model the loading on bridges with two independent streams of traffic in opposing directions. However, a typical highway bridge will have multiple lanes in the same direction, and various types of correlation are evident in measured traffic. This paper analyses traffic patterns using multi-lane WIM data collected at two European sites. It describes an approach to the Monte Carlo simulation of this …

Management Strategies For Special Permit Vehicles For Bridge Loading, Bernard Enright, Eugene J. Obrien

Conference papers

An examination of weigh-in-motion data collected recently at sites in five European countries has shown that vehicles with weights well in excess of the normal legal limits are found on a daily basis. These vehicles would be expected to have permits issued by the responsible authorities. It can be seen from the measurements that most of them are travelling at normal speeds. Photographic evidence indicates that, while many are accompanied by an escort vehicle, normal traffic is flowing alongside in other lanes. As European freight volume grows, the frequency of these special vehicles can be expected to increase. Hence, the …

Earthquake Resistance Of Integral Abutment Bridges, Robert J. Frosch, Michael E. Kreger, Aaron M. Talbott

JTRP Technical Reports

intermediate length bridges. Integral abutment construction eliminates joints and bearings which reduce long-term maintenance costs. However, in the absence of joints and bearings, the bridge abutments and foundations must be able to accommodate lateral movements from thermal expansion and contraction of the superstructure and from seismic events. Previous research has focused on the response to thermal expansion and contraction. The current research examines the response of integral abutment bridges to seismic loading. A field investigation was conducted to examine the response of an integral abutment to lateral loading from thermal expansion and contraction. The results were used to calibrate analytical …

Analysis Of Effectiveness Of Bridges With Partial Isolation, Wenying Hu

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A special class of seismically isolated bridges shares a common feature in that both ends of the superstructure are restrained and isolators over the columns of bridge uncouple the superstructure from the ground motions. They are defined as partial isolation bridges. From measured acceleration responses, effectiveness of full seismic isolation had been confirmed widely. However, the seismic isolation behavior in the partial isolation has not been widely observed.

The effectiveness of partial isolation is evaluated in this study. The static design procedures for linear and nonlinear partially isolated bridges are developed. Results from the static analysis of linear and nonlinear …

The Structural Reliability Of Bridges Subject To Time-Dependent Deterioration, Colin C. Caprani, C. Mcnally, E. J. O'Brien, A. Bordallo-Ruiz

Conference papers

The reliability of the structural performance of any given structure is affected by both in-service loading and material deterioration due to environmental attack. They must be evaluated at any given time in order to compute lifetime probability of failure. This paper presents an innovative methodology to derive the structure lifetime load effect due to existing traffic using a statistical tool known as Predictive Likelihood. Loss of resistance due to corrosion originated by chloride ingression is also taken into account. Finally the lifetime probability of failure is evaluated via the application of a time-discretization strategy.

Fiber Optic Sensor : Monitoring Precast Beams, Purdue Ect Team

ECT Fact Sheets Archive

A new bridge over the Rio Puerco river, west of Albuquerque will be the first of its kind in the nation with built-in fiber-optic sensors to monitor stress in the bridge's girders. Known as "smart bridge" technology, the self-monitoring system offers many advantages over methods that rely largely on visual inspections.

Bridge Lock-Up Device System, Purdue Ect Team

ECT Fact Sheets Archive

The Colebrand Lock-up Device (LUD) provides additional substructure strength to resist seismic forces as a structural shock transmission unit for highway bridges. This system can provide a temporary rigid link between bridge structural members under seismic, braking, or other fast-acting type loads, while permitting slow thermal movements.

Long-Term Effects Of Super Heavy-Weight Vehicles On Bridges, Scott M. Wood, Necip Onder Akinci, Judy Liu, Mark D. Bowman

JTRP Technical Reports

A permit truck which exceeds the predefined limit of 108 kips is defined as a superload in Indiana. This study was conducted to examine the long-term effects of superload trucks on the performance of typical slab-on-girder bridges and to assess the likelihood of causing immediate damage. Typical steel and prestressed concrete slab-on-girder type bridges were analyzed using both beam line analysis and detailed finite element models. Furthermore, one prestressed concrete bridge and one steel bridge were instrumented using more than 50 sensors each. Strains and deflections were measured during a live load test, and each bridge was monitored for more …

Finding The Distribution Of Bridge Lifetime Load Effect By Predictive Likelihood, Colin C. Caprani, E. J. O'Brien

Conference papers

To assess the safety of an existing bridge, the loads to which it may be subject in its lifetime are required. Statistical analysis is used to extrapolate a sample of load effect values from the simulation period to the required design period. Complex statistical methods are often used and the end result is usually a single value of characteristic load effect. Such a deterministic result is at odds with the underlying stochastic nature of the problem. In this paper, predictive likelihood is shown to be a method by which the distribution of the lifetime extreme load effect may be determined. …

Study Of Same-Lane And Inter-Lane Gvw Correlation, Bernard Enright, Eugene J. O'Brien, Colin C. Caprani

Conference papers

The methodology used is to generate a number of years of simulated traffic and to use extreme value statistics to predict more accurately the characteristic loading for a given bridge. The parameters and probability distributions used in the Monte Carlo simulation must be based on observed sample traffic data. Some previous studies have made unsubstantiated assumptions regarding correlation between the Gross Vehicle Weights (GVW) of trucks in the same lane, or between trucks in adjacent, same-direction lanes. For this paper, an extensive database of Dutch Weigh-in-Motion data is analysed. Data are collected from two same-direction lanes and are time-stamped to …

Statistical Computation For Extreme Bridge Traffic Load Effects, Colin C. Caprani, E. J. O'Brien

Conference papers

The maintenance of highway infrastructure constitutes a major expenditure in many countries. This cost can be reduced significantly by minimizing the repair or replacement of highway bridges. In the assessment of existing bridges, the strength estimate tends to be more accurate than that of traffic loading, due to the more variable nature of loading. Recent advances in the statistical analysis of highway bridge traffic loading have resulted in more accurate forecasts of the actual loading to which a bridge is subject. While these advances require extensive numerical computation, they can significantly improve the accuracy of the calculation. This paper outlines …

Jointless And Smoother Bridges: Behavior And Design Of Piles, Robert J. Frosch, Voraniti Chovichien, Katrinna Durbin, David Fedroff

JTRP Technical Reports

Integral abutment bridges have been used in the United States for decades. By eliminating expensive expansion joints, the piles supporting the end bent accommodate the total thermal movement of the bridge. Currently, integral bridges are designed based upon experience, and a rational design specification has not been developed. Furthermore, the interaction of the abutment, pile, and soil remains uncertain. A better understanding regarding the behavior of this system is needed. The objective of this research is to evaluate the behavior of the integral abutment-pile system and evaluate any limitations of its use. To achieve this objective, two phases of research …

Fatigue Of Older Bridges In Northern Indiana Due To Overweight And Oversized Loads, Volume 1: Bridge And Weigh-In-Motion Measurements, James A. Reisert, Mark D. Bowman

JTRP Technical Reports

This report is the first of a two-volume final report presenting the findings of the research work that was undertaken to evaluate the fatigue behavior of steel highway bridges on the extra heavy weight truck corridor in Northwest Indiana. The purpose of the study was to evaluate the type and magnitude of the loads that travel along the corridor and then assess the effect of those loads on the fatigue strength of the steel bridge structures on the corridor. This volume presents the results of the experimental field study conducted to evaluate the load and load effects on one steel …

Structural Condition Assessment Of Prestressed Concrete Transit Guideways, Robert Zachary Shmerling

Electronic Theses and Dissertations

Objective condition assessment is essential to make better decisions for safety and serviceability of existing civil infrastructure systems. This study explores the condition of an existing transit guideway system that has been in service for thirty-five years. The structural system is composed of six-span continuous prestressed concrete bridge segments. The overall transit system incorporates a number of continuous bridges which share common design details, geometries, and loading conditions. The original analysis is based on certain simplifying assumptions such as rigid behavior over supports and simplified tendon/concrete/steel plate interaction. The current objective is to conduct a representative study for a more …

Deformation Analysis Of Missouri Bridge Approach Embankments, Jonathan L. Robison, Ronaldo Luna

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Missouri has recently experienced below expectation performance or "the bump-at-the-end of the bridge" phenomena at bridge approach slab transitions. Information on approach slab performance was collected state wide to assess if the problem was limited to regional or geological distribution. Finite element analysis was then used to explore the soil embankment-bridge structure differential settlement in two Missouri bridges; MoDOT Bridge A6031 in Livingston County, and MoDOT Bridge A5834 in Pulaski County. These two cases are indicative of the types of soil conditions encountered in the Northern Glaciated Plains region (deeper compressible foundation soils) and the Southern Ozarks region (shallow rocky …

Site-Specific Probabilistic Load Modelling For Bridge Reliability Analysis, Colin C. Caprani, A. Belay, A. J. O'Connor

Conference papers

Reliability assessment of a short span beam-slab reinforced concrete bridge in Vienna is proposed using site-specific traffic data recorded using the Slovenian Weigh in Motion (SiWIM) system. An initial evaluation of the bridge using a determinintic approach shows that the critical limit state is bending. This paper describes the statistical analysis of the SiWIM data and the traffic flow simulations performed to predict the characteristic extreme load effects to which the bridge may be subjected during its remaining lifetime. These values are compared to the magnitude obtained from a deterministic approach. The influence lines used in the simulations are the …

Fatigue Behavior Of Beam Diaphragm Connections With Intermittent Fillet Welds, Part I, Volume 1, Field Evaluation, Tammy L. Canna, Mark D. Bowman

JTRP Technical Reports

This report is the first of a two-part, three volume final report presenting the findings of the research work that was undertaken to evaluate the behavior of Indiana highway bridges with diaphragm members welded directly to the web of the primary beams and girders. Fatigue cracks have been observed at several bridges that utilize the welded diaphragm connection. The seriousness of the cracking and the corresponding potential risk on the integrity of the bridge superstructure were assessed. Inspection and repair guidelines for bridges with the welded diaphragm connections were also developed as part of the research effort. This volume presents …

Fatigue Behavior Of Beam Diaphragm Connections With Intermittent Fillet Welds, Part I, Volume 2, Laboratory Fatigue Evaluation, Amy S. Barth, Mark D. Bowman

JTRP Technical Reports

This report is the second of a two-part, three volume final report presenting the findings of the research work that was undertaken to evaluate the behavior of Indiana highway bridges with diaphragm members welded directly to the web of the primary beams and girders. Fatigue cracks have been observed at several bridges that utilize the welded diaphragm connection. The seriousness of the cracking and the corresponding potential risk on the integrity of the bridge superstructure were assessed. Inspection and repair guidelines for bridges with the welded diaphragm connections were also developed as part of the research effort. This volume presents …

Fatigue Behavior Of Beam Diaphragm Connections With Intermittent Fillet Welds: Part Ii, Brittle Fracture Examination Of The I-64 Blue River Bridge, Mark D. Bowman

JTRP Technical Reports

This report is the second of a two-part, three volume final report presenting the findings of the research work that was undertaken to evaluate the behavior of Indiana highway bridges with diaphragm members welded directly to the web of the primary beams and girders. Fatigue cracks have been observed at several bridges that utilize the welded diaphragm connection. The seriousness of the cracking and the corresponding potential risk on the integrity of the bridge superstructure were assessed. Inspection and repair guidelines for bridges with the welded diaphragm connections were also developed as part of the research effort. This volume presents …

The Examination Of Infra-Red Techniques For Inspection Of Steel Structures I & Ii, Vachirapun Trakulyingyong, Mark D. Bowman

JTRP Technical Reports

Infra-red thermography systems that have been developed over the last few years offer great potential to locate and discover flaws in steel highway bridge structures at a relatively early stage in their development. Under ideal conditions, the use of infra-red instrumentation should allow bridge inspection personnel to rapidly scan the structure and determine if a potential structural problem has developed. If a problem spot is located by the infra-red camera, then the trouble spot can be examined carefully to determine the need for corrective maintenance. The primary purpose of this research study is to evaluate the accuracy and reliability of …

Analysis And Load Testing Of Two Steel Through Truss Bridges In Indiana, Brian Joseph Malone, Mark A. Heffron, J. A. Ramirez, Donald W. White

JTRP Technical Reports

Results of the load tests of two steel through truss bridges were used to evaluate the assumptions used by BARS for the rating of this type of bridge. Based on the results from this study it is recommended that the Indiana Department of Transportation use the load distribution factors in the 1994 LRFD Specifications in the rating of these bridges. This will imply replacing the load distribution factors currently in BARS. The implementation of the new distribution factors will result in a less conservative rating of the longitudinal beams in this type of bridge. The increase in the allowed moments …

Under Pinning And Erosion Protection At The University Road Bridge Dar Es Salaam, F Bucher

Tanzania Journal of Engineering and Technology (TJET)

During the assessment of the manuscript, it was observed that the paper does not include an abstract. The document proceeds directry to the main content without providing a separate abstract that summarize the study's objectives, methodology, key findings and conclusions