Civil Engineering Commons^™

Seismic Performance Of Mid-Rise Code-Conforming X-Braced Steel Frames, Mokhtar Ansari, Hosein Gholi Pour, Amir Safiey

Publications

Prolixity and complexities inherent in the nonlinear dynamic analysis (NDA) impel engineers to lean towards nonlinear static analysis (NSA) in practice. This paper partly explores differences and similarities in responses obtained from these two simulation techniques. The scope of the study is narrowed down to ubiquitous regular code-conforming mid-rise steel X-braced frames. Different common lateral load patterns are coupled with NSA to study their interactive effects on responses. The modal nonlinear static analysis is also carried out, where deemed necessary. NDA using three different earthquake records are conducted as well, to validate NSA results. Results of nonlinear analyses are undertaken …

Fatigue Performance Of Rc Beams Strengthened With Near Surface Mounted Cfrp Composites, Tamer Ghaith Mousa Eljufout

Dissertations

Bridges have a fundamental role in improving the effectiveness of highways and providing an expedient and express traffic system. Over time, Reinforced Concrete (RC) bridges degrade due to gradually increased traffic loads and environmental deteriorations. Subsequently, service loads might cause higher stresses in concrete and steel reinforcement than stresses considered in the design stage. This affects the structural performance of RC beams and leads to sudden fatigue failure. As such, there is an essential need for rehabilitation to avoid hazards and tragedies.

Carbon Fiber Reinforced Polymer (CFRP) composites are becoming widely used to strengthen RC bridges. Near Surface Mounted (NSM) …

A Comparison Of Water Main Failure Prediction Models In San Luis Obispo, Ca, Kyle Eric Aube

Master's Theses

This study compared four different water main failure prediction models: a statistically simple model, a statistically complex model, a statistically complex model with modifications termed the 2019 model, and an age-based model. The statistically complex models compute the probability of failure based on age, size, internal pressure, length of pipe in corrosive soil, land use, and material of the. These two values are then used to prioritize a water main rehabilitation program to effectively use the municipality’s funds. The 2019 model calculates the probability of failure and consequence of failure differently than the statistically complex model by considering corrosive soil …

Investigation Of Grout - A Comparison Of Standard Grout Mix To Self-Consolidating Grout Mix, Rachel Garcia Chandler

Architectural Engineering

Masonry is a major structural material for low rise buildings, however the design of masonry buildings is rarely taught as a formal course at most universities. As part of the educational experience and to become familiar with the specifications and testing procedures for grouted masonry, a student run experiment on varying the water to cement ratio of masonry grout was conducted. The purpose is to report on the effects of changing the water-to-cement (W/C) ratios in a standard grout mix. The typical W/C ratio is approximately 0.80:1.00. In order to show the effects of increasing water in a grout mix, …

Assessing Infrastructure Elements Using Automated Object Detection Technique In Smart City Applications, Majid Mastali

Dissertations

Nowadays, road features are becoming more complex leading to more complicated complaints regarding urban environments. Point Cloud Data (PCD) processing is an essential element for detecting objects and analysing human driving behavior to identify the variables defining challenging objects and maneuvers in smart cities. PCDs include a range of processing, including indirect processing (e.g., data converting, cleaning process) and direct process (e.g., pass through elevation filter, statistical outlier removal, normal estimation as well as classification). Static and dynamic object detection and analysis are typically considered the most sophisticated options subsumed under PCDs. They involve direct evaluation of both static and …

Pedestrian Bridge In Tanzania, Maja Sagaser, Karina Rosales

Architectural Engineering

This senior project originated to address the need of the community of Same, Tanzania. There is a deep and wide ravine which floods, making the path many adults and children take to the Majevu Primary School increasingly difficult and dangerous. This report encapsulates all of the steps taken to complete an approved final design for a footbridge to be constructed over this ravine. It includes the project overview, the architectural and structural design process, as well as the important considerations. There are also structural drawings that include plans, elevations, and details.

Improved Reliability Of Stormwater Detention Basin Performance Through Water Quality Data-Informed Real-Time Control, Sazzad Sharior, Walter M. Mcdonald, Anthony J. Parolari

Civil and Environmental Engineering Faculty Research and Publications

Stormwater detentions basins are designed to capture stormwater to reduce and delay peak flows and to improve water quality. A novel technology proposed to improve basin performance is real-time, active control of the basin outflow, in so-called “smart” stormwater systems. Existing studies demonstrate the performance of active controls that respond in real-time to basin water level, detention time, and rainfall forecast for one or a small number of rainfall events. We hypothesize that the performance of these active controls can be improved by incorporating real-time water quality data into the control algorithm. In addition, we hypothesize that active control performance …

Analysis Of The Effects Of Adaptive Ramp Metering On Measures Of Efficiency With A Proposed Framework For Safety Evaluation, Jacky Loh

Master's Theses

Adaptive ramp metering (ARM) is a widely popular intelligent transportation system (ITS) tool that boasts the ability to reduce congestion and streamline traffic flow during peak hour periods while maintaining a lower implementation cost than traditional methods such as freeway widening. This thesis explores the effectiveness of ARM implementation on an 18 mile segment of the Interstate 80 (I-80) corridor in the Bay Area residing in northern California. Smaller segments of this particular segment were analyzed to determine the effective length of ARM on efficiency at various lengths originating from a known bottleneck location. Efficiency values were also compared against …

In-Plane Cyclic Behavior Of A Steel Mesh Reinforced Cob Wall, Julia Fremuth Sargent

Master's Theses

This thesis presents the results from in-plane cyclic testing of a reinforced cob wall. Cob is an earthen building material composed of sand, clay, straw and water. Cob is typically constructed with no steel reinforcement; however, the California Building Code requires reinforcement in all buildings for resisting seismic forces. The purpose of this thesis is to provide additional technical data to integrate cob into the building code.

Test results are reported for a 7’ x 8’ x 14” wall with two layers of welded wire steel reinforcement constructed on a reinforced concrete foundation. In-plane cyclic loading was performed on the …

Case Study: Using Geofoam On A School Project In Encinitas, Ca, Matthew D. Gaebe

Construction Management

This paper is a case study that identifies why Geofoam was used as in-fill material for a construction project located at a high school in Encinitas, CA. The Geofoam was installed under a stairway that connects to a structural retaining wall. The concrete formwork was connected directly to the foam and the stairs were poured in place onsite. The foam acted as the on-grade material, so the concrete stairs did not have to be self-supporting. The purpose of this study is to understand the benefits of using Geofoam, as the in-fill material, as opposed to other traditional materials. An analysis …

Affordable Learning Solutions And Interactive Content In Engineering Mechanics, Nicolas Ali Libre

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Digital Affordable Learning Solutions (ALS) provides students with quality yet affordable educational content and enables instructors to utilize multimedia and interactive technology as effective ways of delivering course material. The reduced course content expenses not only allow more students to access the educational material, but also permit the instructors to customize and adapt the material to their teaching style. Incorporation of interactive technology through visually appealing media such as animations, graphics, simulations, videos, and three-dimensional models promotes students' interest in learning theoretical and abstract subjects in science and engineering. In this study, the incorporation of an interactive eBook as an …

Effect Of Specimen Thicknesses On Water Absorption And Flexural Strength Of Cfrp Laminates Subjected To Water Or Alkaline Solution Immersion, Xue Zhang, Yanlei Wang, Baolin Wan, Gaochuang Cai, Yuan Qu

Civil and Environmental Engineering Faculty Research and Publications

In this paper, an experimental research was undertaken to investigate the effect of specimen thicknesses on water absorptions and flexural strengths of wet lay-up CFRP laminates subjected to distilled water or alkaline solution immersion up to 180 days. Test results showed that the water uptake and flexural strength retention of CFRP laminates were significantly affected by the adopted specimen thickness. For the same aging time, the water uptake of CFRP laminates decreased in the early stage of immersion and increased in the later stage of immersion with the increase of specimen thickness. Meanwhile, the flexural strength retention generally increased as …

Investigating The Rapid Curing Possibility Of Geopolymer Concrete, Ashlesh Banjara

Master's Theses

Recent studies of heat-cured fly ash based green geopolymer concrete have shown its suitability for fabrication of structural members. Fabrication of these structural members requires continuous moderate heating (145°F) for 24 hrs, and an oven essential, for a large member can quickly turn into an energy guzzler, potentially eliminating the green credentials of the product. The proposed research involves the development of a frontal polymerization (FP) method that achieves rapid curing of geopolymer at ambient condition after short-term heat application. Initial work shows thermal FP in geopolymer is a possibility and might be a solution to the problem. The process …

Effects On Strength And Corrosive Characteristics Of Hardened Cement Paste Using Rice Husk And Sugarcane Bagasse, Travis D. Garrett

Master's Theses

Cement is one of the most used building materials in the world. The production of ordinary Portland cement contributes to the release of harmful greenhouse gasses. In an effort to reduce these emissions, different materials are being evaluated for their use as partial replacements for ordinary Portland cement. Rice husk and sugarcane bagasse are agricultural waste products and large amounts of these are currently landfilled, making them inexpensive and available. When combusted at high temperatures they form rice husk ash and sugarcane bagasse ash that have pozzolanic characteristics. The high silicon dioxide in these products makes them good options to …

Total Fume Emissions And Emission Factors Applicable To Gas Metal Arc Welding, Nayara De Souza

LSU New Orleans Theses and Dissertations

Welding is a common industrial practice that has the potential to emit air pollutants. Emission factors are useful indicators to help in the understanding of the extent of pollution from a process and managing them to reduce or minimize health impacts. The objective of this thesis is to determine emission factors applicable to the gas metal arc welding (GMAW), under varying current and voltage conditions. The most used base metals and an electrode for the shipbuilding industry were considered. A weld fume chamber was used to achieve the project goals along with standard sampling and analytical procedures. Three test runs …

Development Of Traffic Live Load Models For Bridge Superstructure Rating With Rbdo And Best Selection Approach, Sasan Siavashi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

Reliability-based design optimization (RBDO) is frequently used to determine optimal structural geometry and material characteristics that can best meet performance goals while considering uncertainties. In this study, the effectiveness of RBDO to develop a rating load model for a set of bridge structures is explored, as well as the use of an alternate Best Selection procedure that requires substantially less computational effort. The specific problem investigated is the development of a vehicular load model for use in bridge rating, where the objective of the optimization is to minimize the variation in reliability index across different girder types and bridge geometries. …

Numerical Modeling Of Wave Dynamics And Sediment Transport Near The Mississippi Birdfoot Delta And Barataria Estuary, Soroush Sorourian

LSU Doctoral Dissertations

The Barataria Basin is a large estuarine system in Southeastern Louisiana, connected to the Gulf of Mexico through a number of inlets, the most important of which is the Barataria Pass. This research examines, during April-June 2010 including both cold front passage and calm summer-time wind regimes, the wave dynamics in this basin and in its major inlets, morphological evolution near the Barataria Pass, and the budgeting and dispersal of the Mississippi River sediment in the birdfoot delta region. An unstructured grid, terrain following, high resolution coupled FVCOM-SWAVE-SED model is employed and validated in this study. The numerical model results …

The Critical Difference Seismic Design Can Make For A Reinforced Concrete Building Located In Oxford, Mississippi, Naim Daghmash

Honors Theses

The Senior Design course at the University of Mississippi requires the completion of a capstone project. One part of the capstone project is a complete structural design of the NOLA, an ongoing construction in the city of Oxford in Mississippi. The course requires the NOLA to be designed according to gravity loads, meaning the forces act in the downward direction towards the earth’s surface. Some loading mechanisms that could occur in a different direction than gravity are seismic loads, which are earthquake-generated loads. I was not required by my instructors to consider the effect of an earthquake on the structural …

A Comparative Study Of Insertion Loss Of Traffic Noise Barriers In Georgia, Pablo Giraldo, Jidong Yang

Master of Science in Civil Engineering Theses

In this paper, three types of traffic noise barriers, interlocking steel panels, precast concrete panels, and Paragon panel 23-T, were evaluated in terms of insertion loss. Field test was conducted for the noise barriers recently installed as part of the Northwest Express Project in Georgia. The noise insertion loss was measured as noise difference in A-weighted decibels (dBA) immediately before and after the barriers. The insertion loss was then evaluated by correlating with noise barrier types and other influential variables, including the separation distance of barriers from traffic, the level of traffic, wind speed, and pavement types. The results showed …

2019 05 6 Asce Golden Spike Ces W Eicholtz.Pdf, Michael Oconnor

Department of Civil and Environmental Engineering Faculty Publications

...

How Moisture Content Levels And Packing Density In Soil Affect Crude Oil Spreads, Shaylin N. Williams

Venture: The University of Mississippi Undergraduate Research Journal

Crude oil spills are one of the most destructive disasters that can occur, and they are extremely difficult to recover from. Many studies focus on what can be done to clean these crude oil spills, but more research should be focused on means of prevention. Currently, very little is known about how the moisture content levels and the packing efficiency of soil can affect an oil spill. These two factors alone can offer a variety of information to environmental agencies, manufacturers, and refineries. Through utilization of a chemical engineering lab, a recording mechanism, and ImagePro software, data was collected and …

Development Of Daily, Monthly, Inter-Annual, And Mean Annual Hydrological Models Based On A Unified Runoff Generation Framework, Marwan Kheimi

Electronic Theses and Dissertations

The main goal of this dissertation develops a unified model structure for runoff generation based on observations from a large number of catchments. Furthermore, obtaining a comprehensive understanding of the physical controlling factors that control daily, monthly, and annual water balance models. Meanwhile, applying the developed Unified model on different climate conditions, and comparing it with different well-known models. The proposed model was compared with a similar timescale model (HyMOD, and abcd) and applied on 92 catchments from MOPEX dataset across the United States. The HyMOD and abcd are a well-known daily and monthly hydrological model used on a variety …

Enhancing Anaerobic Oxidation Of Methane In Landfill Cover Soil, Niloofar Parsaeifard

Civil Engineering Dissertations - Archive

Methane (CH4) is one of the major greenhouse gases (GHG) generated in landfills and has a global warming effect 28 times more than carbon dioxide (CO2). Therefore, decreasing methane emissions into the atmosphere from landfills is critically important. In the upper portions of a landfill cover, methane is exposed to oxygen and oxidized aerobically to carbon dioxide while passing through the cover soil; this lowers the overall contribution of the landfill to climate change. However, because of the low permeability of the landfill cover, no aerobic oxidation occurs in the bottom of the cover because oxygen cannot penetrate to those …

Performance Of Concrete Slabs With Embedded Hydronic Loops For Geothermally Based Bridge De-Icing Applications, Mark Hurley

Civil Engineering Theses - Archive

Geothermal energy has always been available as a renewable thermal reserve, however, only recently has it been unlocked as a potential source of energy to de-ice bridges and roadways. The ability to efficiently extract the geothermal reserves has been accomplished with the advent of new technology. Each progressing year, the refinement of technology has led to a reduction in the input required to achieve a desired output. For the case of bridge de-icing, the extracted input of thermal energy must exceed the required demands to permit de-icing. The conventional approach to de-icing (using chemicals, salt, and sand) works as a …

Service Life Prediction And Risk Analysis Of Reinforced Concrete Gravity Flow Pipes Using Reliability Theory, Khaled Saleh Abuhishmeh

Civil Engineering Theses - Archive

Reinforced concrete pipes are susceptible to different types of deteriorations that threaten their structural capacity and serviceability. Failure of these structures or losing parts of their operational capabilities may cause undesirable consequences that affect the surrounding environment, public health and the economy. The main objectives of this research are to estimate the service life, and to evaluate the level of risk of reinforced concrete sewer pipes (RCP) that are under persistent chemical deterioration caused by the sulfide attack that leads to excessive erosion along the pipe’s interior wall. In order to estimate the service life, reliability theory is used by …

Flexural Behavior Of Preflex Sfrc-Encased Steel Joist Composite Beams, Nancy Thazhampallatu Varughese

Civil Engineering Theses - Archive

This research investigates the behavior of encased steel composite beams within steel fiber reinforced concrete (SFRC) in straight and preflex beams, using nonlinear analysis. ABAQUS FEA software has been adopted. Composite steel beams encased in fiber reinforced concrete are analyzed and a comparison is made with available experimental results. Good agreement with the experimental results is observed. Upwards camber of the steel section is introduced on the steel joist. It’s found that the preflex section can increase the ultimate load capacity by 10% and decrease midspan displacement by 13% of the same beams without the preflex steel section. Steel fiber …

Experimental Investigation Of Concrete Breakout Strength Of Anchors In Shear Within Fiber Reinforced Concrete, Mohammad Akram Khanfar

Civil Engineering Theses - Archive

This study investigates the effects of Polypropylene fibers on the concrete breakout strength of cast in place anchors in shear under different loading rates. The steel headed anchors were cast within concrete specimens of different amounts of Polypropylene fibers. Four differing mixtures were produced using, 0, 0.5, 1, and 1.5% fibers by volume of the mixture. Their physical properties were calculated through testing at the Civil Engineering Laboratory Building. In total, 16 cylindrical specimens, 4” in diameter and 8” in height, and 6 beam specimens, 6”x6”x20” were produced and tested. After 28 days of curing, the specimens were tested for …

Effect Of Termite Gut Microorganism Tav5 Ratios On Lignin Degradation And Methane Generation From Paper, Yard, And Wood Waste, Hoda Rahimi

Civil Engineering Dissertations - Archive

Methane from anaerobic processes is being increasingly utilized as an alternative energy source in developed countries, via large projects that extract methane from landfills or wastewater treatment plants. Anaerobic degradation of organic material (biomass) involves decomposition by bacteria under humid conditions without any oxygen. Organic carbon deposited in landfills is converted by microbes to carbon dioxide (CO2) and methane (CH4). If the methane is not captured, it contributes to climate change (28 times more effectively than CO2 on a per-mass basis). If the methane is captured, it can be used as a renewable energy resource. Lignocellulose comprises a significant portion …

Investigation Of Gas- And Liquid-Phase Sewer Environmental Factors Leading To Microbially-Induced Concrete Corrosion, Aiswarya Acharath Mohanakrishnan

Civil Engineering Theses - Archive

Sewer systems are a principal element of infrastructure in modern cities, accounting for massive amounts of public investments made over many decades and can be considered as an asset of the nation. Many concrete manholes in the sewer system are deteriorating due to the attack of sulfuric acid produced by microorganisms in a process termed as Microbial Induced Concrete Corrosion (MICC). The life span of concrete sewer elements significantly reduces from 100 years to 30–50 years, in extreme cases even down to 10 years. The primary aim of this study is to enhance the understanding of the correlation between gas-phase …

Analysis Of Hydrodynamic And Bathymetric Gradients In Canaveral National Seashore Following Living Shoreline And Oyster Restorations, David Spiering

Electronic Theses and Dissertations

Coastal vulnerability has been gaining recognition as a critical issue, especially with the increasing predictions of sea level rise. Susceptibility to extreme events, eutrophication, and shoreline modification has left many coastal regions in a degraded state. Shoreline protection has traditionally taken the form of seawalls and offshore breakwaters which can be detrimental to both the local ecosystems and adjoining shorelines. The objective of this thesis is to analyze the hydrodynamic and bathymetric variation that occurs within Mosquito Lagoon, Florida following living shoreline and oyster reef restorations. The shoreline sites were sampled using a Before-After-Control-Impact (BACI) design and data were analyzed …