Civil Engineering Commons^™

Planning, Design, And Operational Analysis Of Underground Freight Transportation Systems With Individual Autonomous Vehicles, Sirwan Shahooei

Civil Engineering Dissertations - Archive

Given the increases in freight transportation demand, the current infrastructure for freight transportation appears insufficient. Moreover, the future development of capacity for freight transportation infrastructure seems to be limited. Based on a U.S. DOT report, most of the U.S. freight transportation infrastructure’s construction dates back to the 1960s. This puts a heavy burden on the national highway and railroad systems. The growing demand for freight will increase truck traffic on both urban and rural highways. The increase in truck traffic on highways will result in multiple challenges, including traffic congestion, security concerns, infrastructure deterioration, environmental pollution, energy consumption, increase in …

Evaluation Of Fiber Reinforced Polymer (Frp) Strengthening For Deteriorated Bridge Bent Caps, Yazan Almomani

Civil Engineering Dissertations - Archive

Deterioration of aging highway bridges has been a serious concern in the U. S. A. Almost 39% percent of all bridges in the country have passed their 50-year design life, and approximately 9% of these bridges are structurally deficient due to concrete deterioration and truck weight increases on highways. Compared to superstructures, the deterioration of bridge substructures and associated repair/strengthening/evaluation has received much less attention in previous studies. A reinforced concrete bridge built in 1940 and located in Dallas, Texas, exhibited moderate to severe corrosion related concrete deterioration in the bent caps. Eight such bent caps were selected herein for …

A New Approach For Performance Evaluation Of Bridge Infrastructure Using Terrestrial Lidar And Advanced Mathematical Modeling, Ali Shafikhani

Civil Engineering Dissertations - Archive

High plastic expansive clays when subjected to different climatic conditions undergo large ground movements causing distress to infrastructures including bridges, pavements, buildings, retaining structures, and others. Performance assessment of these structures built on problematic soils such as expansive clays is important to reduce maintenance and extending the design life of infrastructure. Rapid developments in remote sensing technologies with precise evaluation have influenced the monitoring techniques for assessing the health condition of civil infrastructure projects. While these technologies have considerably aided in performance evaluation, cogent procedures for evaluating the ground movements are still required that integrates technologies, climatic factors, soil behavior …

Highway Cross Slope Measurement Using Airborne And Mobile Lidar, Alireza Shams Esfandabadi

All Dissertations

Ensuring adequate pavement cross slope on highways can improve driver safety by reducing the potential for water sheeting and ponding. Collecting cross slope data is typically only based on small sample because efficient technology and means to collect accurate cross slope data has been evasive. The advent of Light Detection and Ranging (LiDAR) scanning technology has proven to be a valuable tool in the creation of 3D terrain models. Combined with other technologies such as Global Positioning Systems (GPS) and Inertial Measurement Unit devices (IMU) it is now possible to collect accurate 3D coordinate data in the form of a …

Feasibility Of Aerial Tramway At Boise State University, Majed Alsaqyani

Boise State University Theses and Dissertations

The use of aerial tramways is becoming common in cities as a way to provide reliable, safe, sustainable, and cost-effective mass transportation. The aerial tramway is especially effective in the most congested areas of major cities. The growth of Boise State University (BSU) and downtown Boise makes this location especially attractive for a tramway. Moreover, based on data collected for this analysis, it is clear that the BSU community is open to using the tramway instead of more traditional modes of transportation.

The viability of the tramway is further enhanced because the computer science department has moved to City Center …

A Comprehensive Seismic Response And Slope Stability Analysis Framework For Evaluating The Stability Of Hydraulic-Fill Dams, Sayantan Chakraborty

Civil Engineering Dissertations - Archive

The stability and serviceability of earthen embankment structures such as dams and levees are extremely crucial to avoid the catastrophic consequences of the failure of these structures. Such man-made geo-structures are usually stable under normal working conditions; however, the stability and subsequent functionality may be affected during earthquake events. Hence, the evaluation of seismic response and structural stability of earthen dams is an important facet in the field of geotechnical earthquake engineering. Dams and levees built in earthquake-prone regions are usually designed to withstand expected seismic events, and in-depth time-history-based dynamic analyses are typically performed to assess the behavior of …

Algorithm Development For Sewer Pipe System Condition Assessment Using Multi-Sensor (Msi) Technology, Mohammed Al Asadi

Civil Engineering Dissertations - Archive

This study investigates the performance of all the current large-diameter pipeline system of The City of Arlington (COA) sewer lines of 48 miles (24-inch inner diameter and above for rigid and flexible pipes). Proper inspection and rehabilitation plan for the city sewer pipeline system are better choice for the municipality and tax payers in terms of cost than dealing with pipe damage and collapsing problems when they happen. The City of Arlington (COA), University of Texas at Arlington (UTA) and RedZone Robotics have established a Technology Partnership Program (TPP) to perform a condition assessment on the all COA large diameter …

Using Finite Element Output To Detect Damage In A Steel Frame Model, Ai D. Nguyen

Electronic Theses and Dissertations

Many structural collapses, all over the world, are related to inspection errors. The U.S. I- 35 Bridge in Minneapolis and the Canterbury Television building in New Zealand are a few examples. U.S. infrastructure conditions are poor, scoring a D+ according to ASCE report 2017. When the structures are inspected, the cost is high and service is lost. Inspectors use their trained but subjective judgment, which can lead to errors. Improved inspection techniques are required to reduce the cost, time, and subjectivity.

SHETM (Structural Health EvaluationTM) is an in-house software that has the ability to employ data to improve damage detection …

A Framework For Assessing Sustainability Impacts Of Truck Routing Strategies, Haluk Laman

Electronic Theses and Dissertations

The impact of freight on our transportation system is further accentuated by the fact that trucks consume greater roadway capacity and therefore cause more significant problems including traffic congestion, delay, crashes, air pollution, fuel consumption, and pavement damage. Assessing the actual effects of truck traffic is a growing need to support the ability to safely and efficiently move goods and people in areas where roadway expansion is not the best option. On one hand, trucks need to efficiently serve commerce and industry, while at the same time their activities need not contribute to a decline in the quality or public …

Studying The Applicability Of Biostimulated Calcite Precipitation In Stabilizing Expansive Soils, Md Touhidul Islam

Boise State University Theses and Dissertations

Of the four types of soils, clays are often associated with issues related to low bearing capacity, high compressibility, swelling and shrinking nature. For example, expansive soils swell and shrink with moisture ingress and digress and are prevalent in several parts of the world causing billions of dollars in damages annually to various civil infrastructures. Several ground improvement techniques such as chemical stabilization, deep soil mixing, moisture barriers, and others were employed to counteract these soils. However, these methods are impractical in certain situations and unsustainable in others due to their economic and environmental impacts. Microbiological treatment of soils could …

Maintaining Deck Profile In Steel I-Girder Bridges During Deck Placement, Ali Naif Inceefe

Masters Theses

Conventional steel I-girder highway bridges utilize cast-in-place concrete deck. Maintaining the deck profile as per project specifications might be a challenging task. Deformation of girders and formwork used for deck placement need to be controlled during deck placement. Differential deflection between girders, exterior girder web out-of-plane deformation, exterior girder warping, or a combination thereof could impact the deck profile. These deformations challenge maintaining deck profile and need to be considered as a part of constructability evaluation. Determining deck profile due to potential girder deformations is necessary before deck placement so that the remedial actions can be implemented when deck finish …

Evaluation And Development Of Cpt Based Pile Design In Nebraska Soils, Alex Silvey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Cone penetration testing (CPT) is a well established geotechnical subsurface investigation technique commonly used for site characterization and soil classification. The CPT gives real time end resistance, side friction, and pore pressure readings. Axially loaded piles also share these two resistance mechanisms, suggesting the cone can be considered similar to a miniature pile. This study focused on evaluating eight CPT methods prediction of pile bearing capacity. The Nebraska Department of Roads (NDOR) conducts dynamic load tests (PDA) of driven pile to verify pile capacity for bridge foundations. 91 comparisons of CPT logs and PDA data were evaluated. CPT prediction methods …

Understanding Asphalt Concrete Aging Using Nanoindentation, Hasan M. Faisal

Civil Engineering ETDs

Asphalt concrete (AC) is created by mixing liquid asphalt binder with solid aggregates. When asphalt binder is mixed with aggregates, it creates a thin film (about 7-16 microns thick) around the aggregate surface. Fine aggregate (smaller than 0.075 mm size) get entrapped within the binder film or mixed with the binder, and create a phase called mastic. Both asphalt film and mastic play significant roles in aging of asphalt pavement. To this day, tests were performed mainly on the bulk liquid asphalt, but not on the film or mastic. In this study, for the first time, nanoindentation tests were done …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …

In Situ Strain And Damage Monitoring Of Gfrp Laminates Incorporating Carbon Nanofibers Under Tension, Yanlei Wang, Yongshuai Wang, Baoguo Han, Baolin Wan, Gaochuang Cai, Ruijuan Chang

Civil and Environmental Engineering Faculty Research and Publications

In this study, conductive carbon nanofibers (CNFs) were dispersed into epoxy resin and then infused into glass fiber fabric to fabricate CNF/glass fiber-reinforced polymer (GFRP) laminates. The electrical resistance and strain of CNF/GFRP laminates were measured simultaneously during tensile loadings to investigate the in situ strain and damage monitoring capability of CNF/GFRP laminates. The damage evolution and conduction mechanisms of the laminates were also presented. The results indicated that the percolation threshold of CNFs content for CNF/GFRP laminates was 0.86 wt % based on a typical power law. The resistance response during monotonic tensile loading could be classified into three …

Investigating The Pavement Vibration Response For Roadway Service Condition Evaluation, Zhoujing Ye, Yang Lu, Linbing Wang

Civil Engineering Faculty Publications and Presentations

Dynamic response of pavement provides service condition information and helps with damage prediction, while limited research is available with the simulation of pavement vibration response for evaluating roadway service condition. +is paper presents a numerical model for the analysis of the pavement vibration due to the dynamic load created by a passing vehicle. A quarter vehicle model was used for the determination of the vehicle moving load. Both random and spatial characteristics of the load were considered. The random nonuniform moving load was then introduced in a 3D finite element model for the determination of the traffic-induced pavement vibration. The …

Connected Autonomous Vehicles: Capacity Analysis, Trajectory Optimization, And Speed Harmonization, Amir Ghiasi

USF Tampa Graduate Theses and Dissertations

Emerging connected and autonomous vehicle technologies (CAV) provide an opportunity to improve highway capacity and reduce adverse impacts of stop-and-go traffic. To realize the potential benefits of CAV technologies, this study provides insightful methodological and managerial tools in microscopic and macroscopic traffic scales. In the macroscopic scale, this dissertation proposes an analytical method to formulate highway capacity for a mixed traffic environment where a portion of vehicles are CAVs and the remaining are human-driven vehicles (HVs). The proposed analytical mixed traffic highway capacity model is based on a Markov chain representation of spatial distribution of heterogeneous and stochastic headways. This …

Mathematical And Numerical Modeling Of Hybrid Adsorption And Biological Treatment Systems For Enhanced Nitrogen Removal, Karl A. Payne

USF Tampa Graduate Theses and Dissertations

High nutrient loading into groundwater and surface water systems has deleterious impacts on the environment, such as eutrophication, decimation of fish populations, and oxygen depletion. Conventional onsite wastewater treatment systems (OWTS) and various waste streams with high ammonium (NH4+) concentrations present a challenge, due the inconsistent performance of environmental biotechnologies aimed at managing nutrients from these sources.

Biological nitrogen removal (BNR) is commonly used in batch or packed-bed reactor configurations for nitrogen removal from various waste streams. In recognition of the need for resource recovery, algal photobioreactors are another type of environmental biotechnology with the potential for simultaneously treating wastewater …

Pressure Swing Adsorption Separation Of H2s/Co2/Ch4 Gas Mixtures With Molecular Sieves 4a, 5a, And 13x, Howell H. Heck, Merilyn L. Hall, Rudy Dos Santos, Manolis M. Tomadakis

Mechanical and Civil Engineering Faculty Publications

Pressure swing adsorption experiments were carried out for the separation of equimolar mixtures of carbon dioxide and methane containing small amounts of hydrogen sulfide, utilizing 4A, 5A, and 13X molecular sieves. High-purity methane of zero or nearly zero hydrogen sulfide concentration was produced in the adsorption stage with 13X and 5A sieves, at high product recovery rates; high-purity carbon dioxide was obtained with the same sieves in the desorption stage. Zeolite 4A was found capable of raising considerably the hydrogen sulfide concentration in the accumulated desorption product (vs. the adsorption feed) at high recovery rates too. Adsorption selectivity values derived …

Characteristics And Applications Of Biochars Derived From Wastewater Solids, Zhongzhe Liu, Simcha L. Singer, Yiran Tong, Lee Kimball, Erik Anderson, Matthew Hughes, Daniel Zitomer, Patrick J. Mcnamara

Civil and Environmental Engineering Faculty Research and Publications

Pyrolysis is a thermochemical decomposition process that can be used to generate pyrolysis gas (py-gas), bio-oil, and biochar as well as energy from biomass. Biomass from agricultural waste and other plant-based materials has been the predominant pyrolysis research focus. Water resource recovery facilities also produce biomass, referred to as wastewater solids, that could be a viable pyrolysis feedstock. Water resource recovery facilities are central collection and production sites for wastewater solids. While the utilization of biochar from a variety of biomass types has been extensively studied, the utilization of wastewater biochars has not been reviewed in detail. This review compares …

Measuring And Evaluating Safety Maturity Of Construction Contractors: Multicriteria Decision-Making Approach, Ali A. Karakhan, Sathyanarayanan Rajendran, John Gambatese, Chukwuma Nnaji

All Faculty Scholarship for the College of the Sciences

Evaluating the safety maturity of construction contractors before awarding the contract is an effective strategy that many owners have started to implement. Given the importance of workplace safety, awarding the contract to safer contractors can enhance project performance outcomes in terms of safety, quality, cost, and schedule. Safety maturity is one quality of a construction organization encompassing interdependent factors that can be used to evaluate expected safety performance. However, there is no formal decision-making framework available in literature that owners can use to evaluate contractor safety maturity. The present study aims to bridge this gap in safety knowledge by proposing …

Lateral Deformation Behavior Of Mass Timber Beam To Column Gravity Connection, Tyler James Williams

Civil and Environmental Engineering Master's Project Reports

A beam-to-column connection consisting of glulam beam and column and cross laminated timber floor slab was developed and experimentally evaluated for use in buildings that are expected to undergo earthquake-­­induced lateral drift. The connection utilized a passive gap closure mechanism designed to allow beam rotations during lateral drift while minimizing residual separation between the beam and the column following an earthquake. Full scale cyclic experiments were used to validate the connection’s minimal rotational stiffness and demonstrate low damage performance for lateral drifts exceeding 4.5% drift. The connection exhibited no degradation in gravity load capacity throughout the imposed lateral deformations. An …

A 3d Model For Earthquake-Induced Liquefaction Triggering And Post-Liquefaction Response, Arash Khosravifar, Ahmed Elgamal, Jinchi Lu, John Li

Civil and Environmental Engineering Faculty Publications and Presentations

A constitutive soil model that was originally developed to model liquefaction and cyclic mobility has been updated to comply with the established guidelines on the dependence of liquefaction triggering to the number of loading cycles, effective overburden stress (Kσ), and static shear stress (Kα). The model has been improved with new flow rules to better capture contraction and dilation in sands and has been implemented as PDMY03 in different computational platforms such as OpenSees finite-element, and FLAC and FLAC3D finite-difference frameworks. This paper presents the new modified framework of analysis and describes a guideline to calibrate the input parameters of …

Development Of A Small Diameter Rapid Pressuremeter Test For Unbound Pavement Layer Evaluations, Thaddeus Joseph Misilo Iii

Theses and Dissertations

Six inch and 12 inch long small diameter pressuremeter (SDPMT) probes were developed and tested extensively to determine in situ stress-strain properties of unbound pavement layers. They were deployed in the same hole as the one made during nuclear density testing. The stress strain response of conventional or incremental and continuous or rapid strain controlled tests in unbound pavement layers were evaluated at four sites in Brevard County, Florida. One test site was A-1-b base material, one was A-3 subgrade and two were compacted A-3 fill of subgrade quality. The SDPMT results were compared with nuclear density dry and wet …

Determining The Location Of Runway Exits Using Airport Surface Detection Equipment, Christopher Bryan Clemmer

Doctoral Dissertations and Master's Theses

Airport surface detection equipment, such as ASDE-X, is used by thirty-five commercially operated airports throughout the United States. ASDE-X is responsible for the safe monitoring of aircraft movements as well as ground support vehicle operating on the airfield. Like most radar-based technologies, ASDE-X can report the position of any aircraft within a one second time interval. This data not only contains the geographic position, but also reports speed, heading, altitude, and aircraft specific characteristics. Using a quantitative approach, this research will use the data reported by ASDE-X to analyze current runway exit locations and develop an improved method of determining …

Bs News July/August

Building Services Engineering

No abstract provided.

Tornado And Hurricane Hazards: Reconnaissance, Structural Analysis And Vulnerability Modeling, Fernando Simon Plaz

Theses and Dissertations

This thesis is composed of three main projects which are directly linked to wind engineering. Hazards such as tornadoes and hurricanes are natural disasters which causes human and economic losses. First, the study consists on a forensic analysis made to a Tornado that hit Funing and Sheyang counties, in the Jiangsu Province of China. 21 villages, mostly rural, experienced important damages to different type of structures. The work will describe field observations and structural analyses made to communication towers. Preliminary estimates of wind speeds will be given based on the observations and the analysis as well as recommendations to reduce …

Modelling Transport Of Nitrogen Compounds In Geita Wetland Along Mtakuja River, Ezrael Masawe

Tanzania Journal of Engineering and Technology (TJET)

The impacts of excessive nitrogen loading to streams in a watershed occur in the receiving waters such as rivers at the outlet of the watershed. To quantify the impacts of land use and management practices on the nitrogen loading at the watershed outlet, simulation models are needed that can both predict the nitrogen loading at the edge of individual fields and predict the fate of nitrogen as it moves through the river network to the watershed outlet. This paper presents the results of a model analysis for describing the processes governing transformations and transport of nitrogen compounds (NO3-N and NH4-N) …

Analysis Of Drought Using Meteorological And Microwave Remote Sensed Data: A Case Of Wami Watershed, Tanzania, Deogratias Mulungu

Tanzania Journal of Engineering and Technology (TJET)

Agricultural sector is important for the economy of Tanzania, but in recent years there is decline in its growth and performance because of persistent droughts. An in-depth study of droughts was conducted on Wami watershed through rainfall and satellite microwave remote sensing data leading for estimates of meteorological droughts and soil moisture based droughts, respectively. Rainfall data during 1973-2008 was used to obtain Drought Severity Index (DSI) and active imaging microwave radar data during 1997-2009 from ESA’s SAR missions of ENVISAT and ERS was used to obtain soil moisture anomalies (SMA). Soil map was used to explain discrepancies in droughts …

The Fate Of Nitrogen And Faecal Coliform In The Lubigi Wetland In Uganda, Aloyce Mayo

Tanzania Journal of Engineering and Technology (TJET)

The capacity of the Lubigi wetland to reduce nitrogen and faecal coliform pollution entering Lake Kyoga in Uganda was investigated. Three transects with 5 sampling points in each, were established in the wetland. Wetland plants samples were collected from the specific locations along the transects, and laboratory tests and analyses were carried out for plants biomass and nitrogen contents determination. Samples of wetland sediments were also collected, and laboratory tests and analyses were done for determination of nitrogen content in the sediments. Wetland water samples were taken from the main wetland inlet and the main outlet from the wetland main …