Civil Engineering Commons^™

Determination Of Critical Parameters For Solar Probe Plus Shielding, Sergio Rafael Mendez

Open Access Theses & Dissertations

A methodology to determine critical design parameters such as critical "design" particle size, and critical "design" impact speed for the shielding of the Solar Probe Plus spacecraft was developed in this thesis. Several critical components and surfaces of the spacecraft such as the Solar Array North, the Thermal Protection System, and the ISIS Instruments were analyzed in this study. The methodology determines the critical "design" particle size based on the required reliability or probability of no impact. Current NASA methods do not provide means to calculate critical "design" impact speeds for missions such as Solar Probe Plus, where the distributions …

Methodology To Convert A Transportation Planning Origin-Destination Matrix Into A Microscopic Traffic Simulation Origin-Destination Matrix, Jose Osiris Vidana-Bencomo

Open Access Theses & Dissertations

Microscopic traffic simulation (MTS) is a cost-effective approach for the evaluation of traffic conditions in urban highways networks. In MTS models, traffic demand that is entered into the network is specified by one or several Origin-Destination (O-D) matrices. A major challenge in the application of MTS for large urban networks is the specification of the O-D matrices. This dissertation proposes a methodology that may be used to transform a O-D matrix from a transportation planning model (which is based on Traffic Analysis Zone, or TAZ, and is readily available) into a O-D matrix for a MTS model (which is traffic …

Evaluation Of Nondestructive Technologies To Assess Presence And Extent Of Delamination Of Hot Mix Asphalt Airfield Pavements, Manuel Celaya

Open Access Theses & Dissertations

Sufficient bonding between the hot mix asphalt layers is essential to ensure the desired structural capacity of a pavement. Delamination or debonding problems are particularly more severe on airfield pavements, due to higher traffic loads applied by aircrafts. Further progression of delamination may result in stripping of the lower layers due to the intrusion of moisture or may develop other dangerous distresses such as foreign object debris. The existing nondestructive testing procedures and equipment that have the potential to address the problem were identified and their effectiveness and potential for success were evaluated. The Ground Penetrating Radar, Falling Weight Deflectometer, …

Impact Of Truck Suspension And Road Roughness On Loads Exerted To Pavements, Shahram Misaghi Bonabi

Open Access Theses & Dissertations

A software package, called IntPave, an Integrated Pavement Damage Analyzer, was developed at the Center of Transportation Infrastructure Systems at The University of Texas at El Paso with the capacity to calculate the pavement distress for flexible pavements under any type of traffic load, and to make a comparison of the level of distress caused by a standard and a non-standard, assuming statically exerted loading. However, what has been lacking is a tool to measure the dynamic impact on the pavement due to vehicle-road interaction. In this report, the interaction of truck suspension systems with the roughness of the road …

Adaptation Of Low Impact Design To The Desert Southwest, Abubaker Ali Alamailes

Open Access Theses & Dissertations

A low Impact Development (LID) practices were used to design an Integrated Management Practices (IMP) system for a residential lot .The design was adapted to the Desert Southwest region based on twenty years of climate data including precipitation and temperature for three representative cities: El Paso, TX, Albuquerque, NM, and Phoenix, AZ. In order to capture stormwater runoff close to its source and to provide as much stored water as possible for plants, LID practices including bioretention cells and vegetated swales were applied throughout the lawn. The purpose of the design is to maintain the pre-development hydrologic characteristics of the …

Improved Joining Method For Segmental Prestressed Structures, Ralph Warren Jensen

Open Access Theses & Dissertations

This dissertation addresses the need for more robust and materially efficient structures, specifically structures that absorb higher levels of energy, can self-erect and which have variable reaction capabilities. These structures can take much higher levels of strain and loading compared to current technologies in reinforced concrete and carbon fiber composites. These structures are made using a novel method of joining segmental elements. A great advantage with this segmental structural system is it's survivability under overloaded conditions. During an impact, or concentrated pressure load, the structure will wrap around the impact zone thereby widely distributing the contact stresses. This function or …

Development Of A New Mix Design Method And Specification Requirements For Asphalt Treated Bases, Hector Antonio Hernandez

Open Access Theses & Dissertations

Asphalt stabilized bases in Texas are usually designed and constructed as per Item 292, "Asphalt Treatment (Plant Mixed)," of the 2004 Standard Specification book. This specification is a hybrid of base and hot mix asphalt concrete procedures and requirements, which are sometimes incompatible. In addition, this Item uses a specific Texas Gyratory compactor that is not readily available to all districts. Some districts have started using test method Tex-204-F, Part III, `Mix Design for Large Stone Mixtures Using the Superpave Gyratory Compactor." However, this procedure was originally developed to design Type A and Type B hot mix at 96% density …

A Tool To Improve And Preserve Flexible Pavement At Intersections, Carlos Jesus Solis

Open Access Theses & Dissertations

Rural intersections originally constructed with thin untreated flexible base and hot mix or a two-course surface treatment tend to experience severe pushing, shoving and rutting. These failures cause an extremely rough surface that can cause damage to small vehicles and potentially cause motorists to lose control of their vehicles. These distresses almost always result in complete failure of the existing pavement that must be repaired several times during the life of the roadway by maintenance forces. In most cases, pavements constructed with the same materials and cross-sections adjacent to the intersection perform adequately.

The sources of and solutions for failure …

Development Of A Land Use Regression Model To Predict Nitrogen Dioxide Concentrations, Teresa Sosa

Open Access Theses & Dissertations

Air pollution is a major environmental concern in the El Paso-Juárez region. According to the Ministry of Environment and Natural Resources (Secretaría de Medio Ambiente y Recursos Naturales, SEMARNAT) the city of Juárez is one of the city's in México with the highest atmospheric levels of pollution because of its accelerated and unplanned urban growth. One air pollutant of concern is nitrogen dioxide (NO2) due to its detrimental health effects that have been associated with airway inflammation in healthy people and increased respiratory symptoms in people with asthma. Land use regression modeling is a GIS based approach that seeks to …

Impact Of Moisture Content And Density On Stiffness-Based Acceptance Of Geomaterials, Lourdes Guadalupe Pacheco

Open Access Theses & Dissertations

Modulus-based quality management of compacted layers has been considered by a number of highway agencies. Even though simple in concept, the paradigm shift from density to modulus for quality acceptance has generated some technical and institutional challenges. One of these complications is that for a given density, the modulus can vastly vary depending on the moisture content at the time of compaction and at the time of acceptance. The results of a systematic study carried out to qualify and quantify the impact of compaction moisture content, moisture content at the time of field testing and density on the modulus and …

A Risk Analysis Framework For Toll Road Revenue Forecasts, Gabriel Alejandro Valdez Ceniceros

Open Access Theses & Dissertations

In the United States, the shortage for traditional public sector funding sources for a safer and more effective highway infrastructure has made it more increasingly difficult for transportation agencies to keep up with the increasing demand. As a consequence, transportation agencies are considering a number of alternatives to raise funds such as charging tolls or cooperating with the private sector. One of the most important steps when analyzing the feasibility of a toll road is the traffic forecast process. However, the uncertainty of the traffic forecast has become apparent across the U.S. as evident in the common overestimation of traffic …

Decision Support Tools For Bus Rapid Transit Corridor Planning, Luis David Galicia

Open Access Theses & Dissertations

Bus Rapid Transit (BRT) Systems have been gained popularity in the United States and worldwide as a cost-effective solution of mass transit. There are certain elements and characteristics that such a system should accomplish to be considered a BRT. However, a uniform definition, defined phases to be deployed, and a reliable methodology to estimate ridership are not well structured and clear yet. The purpose of this research was to help BRT stakeholders with an effective method to plan and assess BRT projects. The first goal of this research was to provide a comprehensive description of the essential characteristics of BRT …

Applicability Of Mepdg For India Based On Texas Pavement And Environmental Conditions, Vamsi Krishna Pinnamaneni

Open Access Theses & Dissertations

The Indian pavement design guide uses empirical models which were adopted and modified from US design guides. As with any empirical model, the prediction capabilities are limited to the conditions for which it was developed. In USA, Mechanistic Empirical Pavement Design Guide (MEPDG) has been recently developed to account for increase in truck traffic and minimize premature failure of pavements. Since the new design uses mechanistic approach, it is expected that the design guide can better predict performance of pavements. In addition, mechanistic approach allows use of design guide for different pavement and environmental conditions by calibrating model parameters for …

Effects Of Unbalanced Approach Volumes On Roundabout Operations, Marilyn Valdez

Open Access Theses & Dissertations

Modern roundabouts are increasingly popular in the United States due to their advantages in improving safety and reducing delay at intersections. A roundabout is an intersection in which traffic enters the intersection and travels in a circular counterclockwise motion around a center island. In a roundabout, priority is given to vehicles traveling in the circular roadway, and incoming traffic at the roundabout approach must yield to the circulating traffic. If there is an unbalance in approach volume, the approaches with higher input volumes may dominate the circulating flow preventing vehicles the other approaches to enter the roundabout. This may consequently …

Probabilistic Analysis Of Concrete Fracture, Mustafa Abushaala Aldalinsi

Open Access Theses & Dissertations

It is well known to civil engineers that fatigue leads to the bulk of structural failures. In plain and reinforced concrete structures, fatigue might account for excessive deformation, excessive of crack widths, de-bonding of reinforcement and rupture of the reinforcement, all of these can lead to structural collapse. Fatigue crack propagation can be a method to predict a remaining life of a structures. Herein will show some works that have been done in order to analyze the fatigue crack growth for plain concrete specimen. The goals of this study are to estimate the critical crack length and remaining life of …

Buckling Of Dome Structure With Opening, Under Wind Load, Anup Ramesh Marathe

Open Access Theses & Dissertations

Double layered parabolic dome structure, with opening in roof is analyzed for buckling under wind load. Domes with three different opening sizes are used and external wind load is applied from different directions without changing the position of the opening. Dead load and internal wind pressure is also applied. The dead load and internal wind pressure is kept constant. The internal wind pressure is applied as per the ASCE building requirement that is once in positive direction which is towards the surface and once in negative direction which is away from the surface. The data for this project was sent …

Verification Of Nyslab A Software For The Analysis Of Jointed Pavements, Maryam Limouee

Open Access Theses & Dissertations

A significant amount of research and development has been conducted for decades to provide a tool for the design and analysis of jointed slabs on different types of foundations. ILLI-SLAB, JSLAB, EverFE and ISLAB are the most used finite element modeling (FEM) codes that have gone through several iterations of improvement. JSLAB has been maintained by the Federal Highway Administration (FHWA) and is distributed free of charge and there is significant interest in further improving the capabilities of that software package.

Researchers at the University of Texas at El Paso have been charged to implement several modifications in the latest …

Asset Management Application Towards An Improved Right Of Way Acquisition, Dora Oralia Francis

Open Access Theses & Dissertations

The purpose of this research is to discover a most suitable approach when the right of way acquisition process begins. As soon as it is known that the right of way acquisitions begin, speculations are made to parcels in order to increase the values of these parcel. Different types of speculations can be made, at a different phase of the right of way (ROW) acquisition process. The parcel cost can vary due to speculations according to the phase of the right of way acquisition process. To help assist the Texas Department of Transportation (TxDOT) on the right of way acquisition …

Assessing Repeatability Of Four-Point Bending Method For Estimating Fatigue Cracking Of Hot Mix Asphalt, Sara -. Montazeri

Open Access Theses & Dissertations

The objective of this thesis was to assess the repeatability of four-point bending method for estimating fatigue cracking of hot mix asphalt. This experimental research examined the influence of mix proportions, specifically asphalt and air void contents, on fatigue behavior of asphalt beam specimens in the laboratory tested with four-point bending method of loading. Following the relevant specifications, the strain-controlled mode of loading was selected. Fatigue failure is expected to occur at the cycle which the flexural stiffness of asphalt specimen reduced to 50% of initial amount. Up to a 1,000,000 cycles of loading were applied to each specimen.

Different …

Integrated Finite Element Analysis Program To Evaluate Pavement Performance And Predict Non-Destructive Testing Response, Cesar Tirado

Open Access Theses & Dissertations

The response of a pavement system under wheel loading has been a subject of research for many decades. Several models have been developed to predict pavement performance based on layer deformation and fatigue cracking. Among them stand out computer programs based on linear elasto-static layered systems and viscoelastic-plastic models; however, newer or more advanced constitutive models cannot be rigorously incorporated into them. In contrast, finite element techniques allow incorporation of nonlinear and viscoelastic-plastic behavior of the pavement materials but licensing of software and the need to train personnel greatly limits its use by highway agencies. A mechanistic-empirical (M-E) approach for …

Methodology To Develop A Minimum Cost Acceptance Sampling Plan For Highway Construction, Gandhar Wazalwar

Open Access Theses & Dissertations

Quality Assurance has always been a part of manufacturing processes. Since World War II, Acceptance Sampling has been introduced and implemented for quality control and improvement. Since statistical methods are applied for quality assurance, especially in acceptance sampling, various methods are becoming popular among the highway agencies over the period of time. As a result, several specifications have been designed to date based upon different statistical theories, each with its own advantages and shortcomings. Acceptance is a form of quality assurance which is employed as an audit tool for decision making to accept or reject the product based on its …

Estimating Variation In Stiffness And Volume Change Of Clays From Geochemical And Index Properties, Cynthia Roxanna Zuniga

Open Access Theses & Dissertations

Clayey soils from six different locations in Texas were analyzed and evaluated with respect to their expansion and shrinkage and change in stiffness associated with moisture content variation. These soils consist of five high plasticity-index (PI) clays (PI greater than 25) and one low-PI clay (PI = 17). The behavior of the clays changes dramatically with moisture content fluctuation, thus causing stiffness and volume changes throughout the year. Total or differential volume movements caused by swell or shrinkage strains of expansive soils and reduction in modulus can exert enough pressure to damage the pavements and cause maintenance problems.

The intent …

Gis-Based Tool For Assessing Hydraulic Performance Of Drainage Infrastructure System In El Paso, Gema L. Camacho

Open Access Theses & Dissertations

Maintaining a city's storm-water drainage infrastructure system can be an overwhelming effort, especially when data is inaccurate, incomplete, or located in disparate sources. This was the case for the City of El Paso. This research was part of a project funded by the City of El Paso to enhance their GIS storm drainage infrastructure system. For the first task of the project, the GIS software was used to store stormwater drainage data into one convenient GIS file. A GIS framework was created during the first phase of the project. This GIS database contained drainage data (such as location, material, dimensions, …

Characterization Of A Mems Accelerometer For A Highway Health Monitoring Ultra-Low Power Sensor, Karla Cecilia Enriquez

Open Access Theses & Dissertations

With the 2009 American Recovery and Reinvestment Act, government officials recognized the need to implement automated methods that reduce the cost of assessment projects and provide a long-term solution to monitor the structural health of bridges and highways. Although important research exists in the area of non-destructive evaluation, current road health monitoring efforts continue to be costly and time consuming. This Thesis focuses on the characterization of a MEMS accelerometer intended to be the basis of a novel ultra-low power sensing system to remotely asses the condition of highways. The architecture of a sensor prototype built to validate an algorithm …

Quantifying Anisotropy In Asphalt Concrete Pavements Using An Ultrasonic Method, Monica C. Jurado

Open Access Theses & Dissertations

Asphalt concrete is a bonded granular material whose internal structure is anisotropic. Such anisotropy is due to anisotropic particles and void's structure, particle distribution and orientation, and restrain and force pattern used during compaction. Even with this knowledge asphalt concrete design is made considering asphalt concrete as an isotropic material. The biggest difference between an isotropic and anisotropic material is that, an isotropic material is characterized by two independent constants and an anisotropic material could be characterized by up to 81 constants. An extensive research to characterize and quantify anisotropy is only available for some composite materials. Based on the …

Expert System Design Guide For Lower Classification Roads Over High Pi Clays, Yaqi Wanyan

Open Access Theses & Dissertations

This research was focused on low-volume roads over expansive clayey soils in Texas. In spite of the redundant pavement designs recommended and widely used in Texas for roads in high PI clay areas, these pavements often fail prematurely. This failure occurs primarily because of the highly variable properties of the clayey subgrade throughout the year due to moisture fluctuations. The problematic nature of high PI clays, despite the fact that volumetric changes such as heaving are sometime considered in the design, is of concern since they contribute to roughness and longitudinal shrinkage cracking of the road, and as such the …

Guidelines For Using Local Material For Roadway Base And Subbase, Biraj Gautam

Open Access Theses & Dissertations

Flexible base materials that meet TxDOT specifications are getting more difficult to purchase in many TxDOT Districts. As a result, higher quality materials have to be hauled long distances, sometimes from other States. This act would significantly increase the costs associated with the construction of roads and subsequent maintenance and rehabilitation of them. Lower quality (i.e., out-of-specification) materials are normally available. If through appropriate modifications of the materials (adjusting the gradation or/and stabilization) or structural design (specifying thicker layers of base and/or hot mix) the use of the local materials can be permitted, the construction can be accelerated and significant …

Allocating Emergency Response Vehicles To Cover Critical Infrastructures, Hao Lei

Open Access Theses & Dissertations

Optimal deployment of limited emergency response service units in a metropolitan area is of interests to public agencies. The limited emergency units not only have to respond to the demand for service by residents and businesses, but also cover Critical Infrastructures (CIs). This Thesis formulates an improved optimization model to allocate different types of Emergency Response Service (ERS) units among their candidate base stations. The allocation of units must ensure maximum coverage to CIs, subject to the capacities of the base stations, service standard in terms of time to reach the CIs, and the availability of the ERS units (when …

Quality Evaluation Of Portland Cement Concrete At Early Age With Free-Free Resonant Column, Gilberto Wenglas

Open Access Theses & Dissertations

At early age, the behavior and mechanical properties of portland cement concrete changes rapidly with time due to hydration. The hydration process consists of a series of chemical reactions that accelerate nonlinearly with the rise in temperature. The hydration process consists of three stages: the dormant period, the setting time, and the hardening time. Timely opening of roads and resumption of constructions depend of the knowledge of these stages. The initial and final setting times are arbitrarily determined by a standard test (ASTM C 403). Although the setting time has been studied for many decades, the new technologies allow making …

Uplift Capacity Of Rigid Pile In Clay Under Inclined Load, Godwin Ikechukwu Ubanyionwu

Open Access Theses & Dissertations

This thesis investigates the uplift capacity of rigid vertical piles embedded in saturated or near-saturated clayey soils subjected to inclined uplifting loads. Pile foundations are widely used in civil engineering applications requiring resistance to both axial and lateral forces, including transmission tower foundations, foundations on expansive soils, and mat foundations in areas subject to rising groundwater tables. While considerable research had addressed compressive load bearing capacity and lateral resistance of piles, experimental data on pile behavior under inclined uplift loading remained scarce at the time of this study. The present study was undertaken to conduct a systematic series of laboratory …