Civil Engineering Commons^™

A Unified Bond Theory, Probabilistic Meso-Scale Modeling, And Experimental Validation Of Deformed Steel Rebar In Normal Strength Concrete, Chenglin Wu

Doctoral Dissertations

"Bond between deformed rebar and concrete is affected by rebar deformation pattern, concrete properties, concrete confinement, and rebar-concrete interfacial properties. Two distinct groups of bond models were traditionally developed based on the dominant effects of concrete splitting and near-interface shear-off failures. Their accuracy highly depended upon the test data sets selected in analysis and calibration. In this study, a unified bond model is proposed and developed based on an analogy to the indentation problem around the rib front of deformed rebar. This mechanics-based model can take into account the combined effect of concrete splitting and interface shear-off failures, resulting in …

Rapid Repair Of Severely Damaged Rc Columns Under Combined Loading Of Flexure, Shear, And Torsion With Externally Bonded Cfrp, Ruili He

Doctoral Dissertations

"This research aimed to develop a technique to rapidly repair reinforced concrete (RC) bridge columns for emergency service restoration after severe earthquake damage has occurred. Experimental and analytical studies were conducted to study the performance and effectiveness of the proposed repair method. The experimental study included a series of 1/2-scale RC square bridge columns originally tested to failure under constant axial and increasing cyclic lateral loadings resulting in combined flexure, shear, and torsion with different torsional-to-flexural moment ratios. Using externally bonded carbon fiber reinforced polymer (CFRP) sheets, each column was repaired over a 3-day period and then retested under the …

Plant Uptake Of Environmental Contaminants: Applications In Phytoscreening, Matthew Alan Limmer

Doctoral Dissertations

"Plants interact directly with their surroundings, extracting nutrients and water from the subsurface to support growth and development of the plant. Through the roots, plants also exude and uptake numerous chemicals. Many of the pathways can also be used by environmental contaminants to be translocated to above ground plant tissues. Such uptake of contaminants has proven useful in remediation and phytoscreening - the use of plants to delineate contaminant plumes. Sampling of trees at contaminated field sites has been used to identify areas of groundwater contaminated with a variety of chlorinated solvents. The use of plants as contaminant biosensors requires …

Seismic Repair Of Bridge Columns With Interlocking Spirals And Fractured Bars, Yang Yang

Doctoral Dissertations

"During earthquakes, reinforced concrete (RC) bridge columns may experience different levels of damage such as cracking, spalling, or crushing of concrete and yielding, buckling, or fracture of reinforcing bars. This study developed and assessed permanent and emergency methods to repair damaged bridge columns with fractured longitudinal reinforcement through experimental and modeling work. The permanent repair method involved replacement of the plastic hinge region by removal of spirals, replacement of longitudinal bar segments by mechanically splicing with new bars segments attached with mechanical couplers, replacement of concrete, and installation of an externally bonded carbon fiber reinforced polymer (CFRP) jacket. The emergency …

Longitudinal Analysis Of Crash Frequency Data, Mojtaba Ale Mohammadi

Doctoral Dissertations

"This study comprises mainly of three papers. First, a systematic evaluation of the effects of Missouri's Strategic Highway Safety Plan between 2004 and 2007 is presented. Negative binomial regression models were developed for the before-through-change conditions for the various collision types and crash severities. The models were used to predict the expected number of crashes assuming with and without the implementation of MSHSP. This procedure estimated significant reductions of 10% in crashes frequency and a 30% reduction for fatal crashes. Reductions in the number of different collision types were estimated to be 18-37%. The results suggest that the MSHSP was …

Mechanism Of Crumb Rubber Modifier Dissolution Into Asphalt Matrix And Its Effect On Final Physical Properties Of Crumb Rubber-Modified Binder, Amir Ghavibazoo, Magdy Abdelrahman, Mohyeldin Ragab

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Modification of asphalt by crumb rubber modifier (CRM) is mostly done through exchange of components between asphalt and CRM. At 160⁰ C and 10 Hz, CRM absorbs aromatics of asphalt and swells; however, at 220⁰ C and 50 Hz, CRM dissolves into the asphalt; this process leads to the release of different components of CRM including carbon black, fillers, and polymeric and oily components. Depending on interaction conditions, CRM dissolution is performed differently, and therefore the state and role of the released components can be different. In this research different mechanisms of dissolution of one size of CRM in asphalt …

Dynamics And Dislodgment From Pore Constrictions Of A Trapped Nonwetting Droplet Stimulated By Seismic Waves, Wen Deng, M. Bayani Cardenas

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Seismic waves affect fluid flow and transport processes in porous media. Therefore, quantitative understanding of the role of seismic waves in subsurface hydrodynamics is important for the development of practical applications and prediction of natural phenomena. We present a theoretical fluid dynamics model to describe how low-frequency elastic waves mobilize isolated droplets trapped in pores by capillary resistance. The ability of the theoretical model to predict the critical mobilization amplitudes (A_c) and the displacement dynamics of the nonwetting droplet are validated against computational fluid dynamics (CFD) simulations. Our theory has the advantage of rapid calculation of A_{c …}

Real Time Bridge Scour Monitoring With Magneto-Inductive Field Coupling, Andriy V. Radchenko, David Pommerenke, Genda Chen, Pratik Maheshwari, Satyajeet R. Shinde, Viswa Pilla, Y. Rosa Zheng

Electrical and Computer Engineering Faculty Research & Creative Works

Scour was responsible for most of the U.S. bridges that collapsed during the past 40 years. The maximum scour depth is the most critical parameter in bridge design and maintenance. Due to scouring and refilling of river-bed deposits, existing technologies face a challenge in measuring the maximum scour depth during a strong flood. In this study, a new methodology is proposed for real time scour monitoring of bridges. Smart Rocks with embedded electronics are deployed around the foundation of a bridge as field agents. With wireless communications, these sensors can send their position change information to a nearby mobile station. …

Pore Geometry Effects On Intrapore Viscous To Inertial Flows And On Effective Hydraulic Parameters, Kuldeep Chaudhary, M. Bayani Cardenas, Wen Deng, Philip C. Bennett

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this article, the effects of different diverging-converging pore geometries were investigated, and the microscale fluid flow and effective hydraulic properties from these pores were compared with that of a pipe from viscous to inertial laminar flow regimes. The flow fields are obtained using computational fluid dynamics, and the comparative analysis is based on a new dimensionless hydraulic shape factor β, which is the "specific surface" scaled by the length of pores. Results from all diverging-converging pores show an inverse pattern in velocity and vorticity distributions relative to the pipe flow. The hydraulic conductivity K of all pores is …

Use Of Ultra-High Performance Concrete To Mitigate Impact And Explosive Threats, Julie Anne Willey

Masters Theses

"This study is a continuation of research conducted by Natalia Carey, Anthony Wulfers, and Dr. John Myers under the DHS ALERT Center. Carey investigated the use of polyurea coating systems to mitigate close range blast threats on wall panels. Wulfers continued this by using both polyurea coatings as well as a sacrificial wood fiber fly ash (WF-FA) layer to try to get increased performance. This research was aimed at the study of ultra-high performance concrete (UHPC) for the use in impact and blast mitigation. There is little information on the performance of UHPC under close range blast loading; therefore it …

Monitoring Micropile Foundations Of Bridge During Construction, Devin Tavis Dixon

Masters Theses

"Information regarding the load transfer of micropiles during in-service construction has virtually never been monitored or documented. The primary objective of this research project was to monitor the load transfer versus the depth of production micropiles during construction. The micropiles being studied were used to support Bridge No. 2 of the Foothills Parkway in eastern Tennessee during construction. Two of the piers (1 & 2) were instrumented for the purpose of this study. Vibrating wire strain gages (VWSG) were installed on select micropiles within pile groups of twenty (20) micropiles. Seven vibrating wire strain gages were installed on each micropile …

Field Performance Of Alternative And Cost Efficient Cast In Place And Precast Prestressed Concrete Bridge Approach Slabs, Nathan Price Muncy

Masters Theses

"In December of 2010, the Missouri Department of Transportation (MoDOT) investigated alternative cost-efficient bridge approach slabs (BASs). New BAS designs were subsequently developed and had a projected cost savings up to twenty-four percent with anticipated equal or better structural performance. A precast-prestressed (PCPS) BAS was introduced as an alternative to traditional BASs that offers advantages such as rapid construction and improved long-term durability. The three new BAS designs were implemented into in-situ bridge projects by MoDOT and the field performance was evaluated within this research study.

Field testing of each BAS was performed using two MoDOT HS20 trucks. Various instrumentation …

Analysis Of Model Uncertainty In Hydraulic Modeling: The Bstem Application To The Osage River, Annabell Leigh Ulary

Masters Theses

"Uncertainty is inevitable when creating any kind of model. A model can be used in the most accurate way possible, if the uncertainties are understood. This study determines the level of uncertainty in the Bank Stability and Toe Erosion Model (BSTEM) of the Osage River downstream of Bagnell Dam between Lake Ozark, MO and Jefferson City, MO. The statistical analysis of the BSTEM model was performed using the aid of SAS statistical computer modeling software. There were 4 different analysis values used to determine the best fit model for all dependent variables. These values include the F-test, the coefficient of …

Effect Of Mix Parameters On Longevity Of Bituminous Mixtures, Clayton Reichle

Masters Theses

"This study was performed to evaluate the effects of varying aggregate sources, aggregate gradations on the stripping and rutting potential of bituminous based plant mixes specified by the Missouri Department of Transportation. The different aggregate combinations included two different aggregate sources (Potosi Dolomite and Jefferson City Dolomite) including two variations for the Jefferson City Dolomite mix to simulate a marginally in-specification mix and an out-of-specification but in-field tolerance mix. The "field" mix simulated the marginal mix where field tolerance of high dust and low binder content were maximized. All three mixes were evaluated for stripping susceptibility using the Tensile Strength …

Direct Shear Transfer Of Lightweight Aggregate Concretes With Non-Monolithic Interface Conditions, Dane Michael Shaw

Masters Theses

"This thesis describes the results of a study initiated to examine the influence of concrete unit weight on the direct shear transfer across an interface of concretes cast at different times. This type of interface is common with structural precast concrete connections, such as corbels, for which shear friction design provisions are commonly used. Increasing use of lightweight aggregate concretes prompted this investigation to determine the appropriateness of current shear friction design provisions with respect to all-lightweight and sand-lightweight concrete. The experimental investigation included thirty-six push-off test specimens, each of which was constructed with a cold-joint at the interface shear …

Modeling Of The Resilient Modulus For Recycled Asphalt Pavement Applications In Base Course Layers, Ehab Noureldin, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The resilient modulus (M_R) is an important parameter for the base course layer in the pavement design process. Use of recycled asphalt pavement (RAP) for this layer must take into consideration the effect of various factors that may occur in the field on the M_R. Previous numerical models used for the granular base layer could be used for the RAP. The study reported here examined the suitability of RAP procedures under the effect of different factors (e.g., water content, dry density, freeze-thaw cycles). Various percentages of the RAP (50%, 75%, and 100% by weight) were employed …

Performance Enhancement Of Crumb Rubber-Modified Asphalts Through Control Of The Developed Internal Network Structure, Mohyeldin Ragab, Magdy Abdelrahman, Amir Ghavibzaoo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Control of the internal network structure of crumb rubber-modified asphalt (CRMA) was investigated for its effect on property development in the study presented in this paper. The investigation included evaluation by rheological and interrupted shear tests. Rheological testing involved the monitoring of the changes of the produced complex modulus (G*) and phase angle (δ) for CRMA. In the interrupted shear tests, the shear stress profile for the produced CRMA was investigated. It was found that triggering the critical conditions of the combined interaction of speed, temperature, and time was essential to inducing the formation of the three-dimensional network …

Cardinal Raúl Silva Henríquez Bridge During The 2010 Chile Earthquake, Zuocai Wang, Genda Chen, W. Phillip Yen, Ian G. Buckle

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents a case study of the Cardinal Raúl Silva Henríquez Bridge, which experienced significant damage during an earthquake that occurred in Chile on February 27, 2010. Supported by reinforced concrete and steel columns of varying heights, the superstructure of the bridge consisted of 22 steel-girder spans, with one intermediate expansion joint located at the middle of the bridge. At each end of the bridge, the bottom flanges of the girders were welded to their bearing steel plates, which were embedded and anchored into the bridge abutment. Two, three-dimensional, finite element models (global versus local) with beam and solid …

The Guayule Plant: A Renewable, Domestic Source Of Binder Materials For Flexible Pavement Mixtures, David Newton Richardson, Steven Michael Lusher

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Due to the rising price of crude oil, flexible pavement costs have increased significantly. This price pressure has resulted in the increased use of reclaimed asphalt pavement (RAP) and/or reclaimed asphalt roofing shingles (RAS) because of the binder (asphalt cement) they contain. This has increased demand for recycling (rejuvenating) agents which return the RAP/RAS binders to their original state by 1) restoring maltenes (petroleum oils and resins) that have been depleted due to age-hardening/oxidation, and 2) reducing their viscosity. The project concept was to design a flexible pavement mixture (FPM) produced with little-to-no virgin petroleumbased binder which implied the use …

Effect Of Crumb Rubber Modifier Dissolution On Storage Stability Of Crumb Rubber-Modified Asphalt, Amir Ghavibazoo, Magdy Abdelrahman, Mohyeldin Ragab

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Crumb rubber-modified asphalt (CRMA) extensively suffers from high-temperature storage instability. Because of the higher density of the crumb rubber modifier (CRM) particles, they settle down to the bottom of storage tanks and cause variation between physical properties of the top and bottom samples. The storage stability of the CRMA changes under different interaction parameters and consequently different mechanisms of interaction. In this research the mechanism of separation under different levels of CRM dissolution was investigated by using Stokes' law. The extent and mechanism of CRM dissolution in asphalt was controlled through regulating interaction temperature and interaction mixing speed. A standard …

Enamel Coated Steel Reinforcement For Improved Durability And Life-Cycle Performance Of Concrete Structures: Microstructure, Corrosion, And Deterioration, Fujian Tang

Doctoral Dissertations

"This study is aimed (a) to statistically characterize the corrosion-induced deterioration process of reinforced concrete structures (concrete cracking, steel mass loss, and rebar-concrete bond degradation), and (b) to develop and apply three types of enamel-coated steel bars for improved corrosion resistance of the structures. Commercially available pure enamel, mixed enamel with 50% calcium silicate, and double enamel with an inner layer of pure enamel and an outer layer of mixed enamel were considered as various steel coatings. Electrochemical tests were respectively conducted on steel plates, smooth bars embedded in concrete, and deformed bars with/without concrete cover in 3.5 wt.% NaCl …

Numerical Analyses Of Long Carbon Fiber Reinforced Concrete Panels Exposed To Dynamic Loading, Zahra Sadat Tabatabaei

Doctoral Dissertations

"The purpose of this research was to evaluate impact and blast performance of long carbon fiber reinforced concrete experimentally and numerically. Experimental tests were conducted on plain concrete (PC), reinforced concrete, and four different types of long carbon fiber reinforced concrete (LCFRC). The results from each test were then compared to one another. This comparison indicates that adding long carbon fibers to concrete both increases the post-cracking behavior of concrete and decreases the spalls in either an impact or blast test. Among all of the fibers tested, Fiber Type B3 outperformed the other fibers, absorbing more energy during impact. Numerical …

Shear And Fracture Behavior Of High Performance Concretes, Mahdi Arezoumandi

Doctoral Dissertations

"Concrete is the most widely used man-made material in the world. Like other materials, it has been improved over time. Nowadays, with continued development of science and technology, a new generation of concretes is produced and is termed high performance concretes. A review of previously published work indicates that very few studies (in some cases none) have addressed the structural behavior of full-scale, high performance concrete elements. This study investigated the shear and fracture behavior of two types of high performance concrete - high-volume fly ash concrete (HVFAC) and self-consolidating concrete (SCC). The HVFAC incorporates up to 70% cement replacement …

Investigation Of The Physical And Molecular Properties Of Asphalt Binders Processed With Used Motor Oils, Mohyeldin Ragab, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this work we investigated the performance aspects of addition of used motor oils (UMO) to neat and crumb rubber modified asphalts (CRMA) and related that to the change of molecular size distribution of modified asphalt’s fractions; asphaltenes, saturates, naphthene aromatics, and polar aromatics. Based on the results of temperature sweep viscoelastic tests, addition of crumb rubber modifier (CRM) alone or with UMO results in the formation of internal network within the modified asphalt. Based on the results of short and long term aged asphalts, the utilization of combination of UMO and CRM enhanced the aging behavior of asphalt. Bending …

An Inverted Teaching Model For A Mechanics Of Materials Course, Jeffery S. Thomas, Timothy A. Philpot

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Instructors at Missouri University of Science and Technology have been offering certain sections of a mechanics of materials course in an inverted format for the past two years. In this format, students learn the concepts outside of class, using a textbook, animations and videos developed by the authors, and work on homework either individually or in groups during the optional class time. Students take eight multiple-choice exams and a final exam that is common to both the inverted sections and the more traditional lecture-based sections. Homework in the inverted sections is assigned but not graded. The in-class exams are given …

Theory For Dynamic Longitudinal Dispersion In Fractures And Rivers With Poiseuille Flow, Lichun Wang, M. Bayani Cardenas, Wen Deng, Philip C. Bennett

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

We present a theory for dynamic longitudinal dispersion coefficient (D) for transport by Poiseuille flow, the foundation for models of many natural systems, such as in fractures or rivers. Our theory describes the mixing and spreading process from molecular diffusion, through anomalous transport, and until Taylor dispersion. D is a sixth order function of fracture aperture (b) or river width (W). The time (T) and length (L) scales that separate preasymptotic and asymptotic dispersive transport behavior are T = b²/(4D _m), where D_m is the molecular diffusion …

Behavior Of Advanced Innovative Materials For Improved Long-Term Bridge Performance, Wei Zheng

Doctoral Dissertations

"The dissertation is to present the investigation results and comprehensive understanding of the long-term performance and behavior of innovative construction materials. The materials are applied in bridge engineering in order to either enhance the conventional materials or replace them. The dissertation consists of two major parts: structural steel coatings for corrosion mitigation and thermal behavior of concrete bridge.

In First Part, evaluation of advanced structural steel coatings was carried out through laboratory weathering tests (salt-fog resistance test and QUV weathering test), adhesion test, and electrochemical techniques. Fifteen coating systems were evaluated in this part, which covered both coating and recoating …

Investigation Of The Effects Of Shrinkage, Creep, And Abrasion On Self-Consolidating Concrete And High Volume Fly Ash Concrete For Use In Transportation Related Infrastructure, Brian Timothy Tucker

Masters Theses

"Concrete specimens were fabricated for shrinkage, creep, and abrasion resistance testing. Variations of self-consolidating concrete (SCC), high volume fly ash concrete (HVFA), and conventional concrete were studied. The results were compared to previous similar testing programs and used to determine the adequacy of the materials for use in practice. These two concrete variations offer significant benefits when used as replacements to conventional concrete. Because of the respective properties of both types of concrete, both economic and environmental benefits are achieved with the use of both. The lower labor costs of SCC and the lower material cost of HVFA lead to …

Driver Mandatory Lane Change Behavior: Use Of Governing Gap In Critical Gap Estimation, Srinadh Kandada

Masters Theses

"This study analyzed the driver gap acceptance and rejection behavior during mandatory lane changes on a multilane freeway in congested and uncongested traffic conditions. During a lane change, drivers were more receptive to either the leading or the trailing gaps with vehicles in the target lane which governed the drivers' lane change and is termed as the governing gap. Drivers maneuvered till the governing gap was greater than the critical gap, accepted the gap and made a lane change. In this process, drivers reduced the non-governing gap to increase the length of the governing gap. The drivers as a result …

Bond Behavior Of High-Volume Fly Ash And Self-Consolidating Concrete, Trevor Jay Looney

Masters Theses

"The main objective of this study was to determine the effect on bond performance of high-volume fly ash (HVFA) concrete and self-consolidating concrete (SCC). The HVFA concrete test program consisted of comparing the bond performance of two concrete mix designs with 70% cement replacement with Class C fly ash relative to a Missouri Department of Transportation (MoDOT) standard mix design. The SCC test program consisted of comparing the bond performance of normal and high strength SCC with their respective MoDOT standard mix designs.

Two test methods were used for bond strength comparisons. The first was a direct pull-out test based …