Civil Engineering Commons^™

Assessment Of Carbon Dioxide Emission And Its Impact On High-Rise Mixed-Use Buildings In Egypt, Ahmed Salah Hamza

Theses and Dissertations

With Egypt's vision of 2030 focusing on sustainable development with a true emphasis on Carbon Dioxide (CO₂) emission reduction in the newly built cities and high-rise buildings, efforts are exerted on various levels towards accomplishing the vision’s goals. This is achieved through multiple tools and models associated with aiding the reduction of carbon emissions, yet not a clear one was introduced for the mixed-use buildings in Egypt.

Through this work, a significant gap was identified with respect to high-rise buildings carbon emission assessment in Egypt. This was a main driving force for this work in an attempt to …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Damage Evolution And High-Rate Response Of High-Strength Concrete Under Triaxial Loading, Brett Williams

Mechanical Engineering Research Theses and Dissertations

The research presented in this study focuses on understanding fundamental mechanisms that drive material response under dynamic loading conditions. The objectives of the research were to: (1) to understand damage initiation and propagation in the bulk geomaterial under a variety of loading conditions and (2) to systematically investigate the strain rate effects on the triaxial compressive response of cementitious materials through the development of an innovative, first of its kind large-diameter (50 mm) triaxial Kolsky bar system.

The triaxial compressive response of high-strength concrete is needed to understand pressure-dependent material behavior, which is important for modeling extreme loading events. However, …

Initial Assessment Of Liquefied Scrap Tire Concrete, Abdulkareem Kuaryouti, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

A new approach to incorporate scrap tire material into concrete was investigated, where two reclaimed waste tire components, carbon black and fuel oil, were used to replace a portion of water. The effect of “liquid tire” content to water ratios from 5-40% on an otherwise typical concrete mix were assessed, where compressive and flexural strength, flexural toughness, modulus of elasticity, and several fresh concrete properties were determined. Results were compared to typically expected results of traditional shredded tire mixes with equivalent tire content. It was found that the liquid tire mixes experienced significantly less losses of compressive strength and workability …

Optimisation Of Retrofit Wall Insulation: An Irish Case Study, Rakshit D. Muddu, D M. Gowda, Anthony James Robinson, Aimee Byrne

Articles

Ireland has one of the highest rates of emissions per capita in the world and its residential sector is responsible for approximately 10% of total national CO2 emissions. Therefore, reducing the CO2 emissions in this sector will play a decisive role in achieving EU targets of reducing emissions by 40% by 2030. To better inform decisions regarding retrofit of the existing building stock, this study proposes Optimum Insulation Thicknesses (OIT) for typical walls in 25 regions in Ireland. The calculation of OIT includes annual heat energy expenditure, CO2 emissions, and material payback period. The approach taken is based on Heating …

Incorporation Of Perlite And Recycled Aggregates For Internal Concrete Curing, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Mohamed Abdel-Raouf Dr.

Civil Engineering

No abstract provided.

Potential Advantages Of Basalt Frp Bars Compared To Carbon Frp Bars & Conventional Steel, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Ezzeldeen Yazeed El Sayed Ahmed Prof

Civil Engineering

No abstract provided.

Timber Bridge Pile Splicing With Fiber Reinforced Polymer Wraps, Drew L. Damich

Graduate Theses, Dissertations, and Problem Reports (ETD)

Timber pile repair using splicing is widely used but little research has been done to determine their strength capacity after repair using this method. Current timber pile splicing mechanisms utilize various steel or wooden components. Fiber Reinforced Polymer (FRP) wraps can be utilized as replacement to conventional materials in splicing of timber piles. This study evaluated the strength capacities of traditional splicing mechanisms in relation to FRP wrap splice mechanisms. Traditional splicing mechanisms consisted of flat steel plate, C-channel steel plate, and wooden plate splices. The FRP wrap splice consisted of unidirectional glass/epoxy composite with three layers of fabric as …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

An Investigation Into The Effects Of Fly Ash On Freeze-Thaw Durability Prediction, Yancy Schrader

Graduate Theses and Dissertations

Air is purposefully entrained into concrete primarily to improve resistance to freeze-thaw deterioration while saturated with water. Air entraining admixtures (AEAs) are chemical admixtures designed to entrain air into the concrete to provide adequate resistance to the effects of freezing and thawing. One of the challenges associated with air entrainment in concrete is the interaction of an AEA with supplementary cementitious materials present in the concrete, particularly fly ash. Fly ash is a by-product of the coal fired electrical generation industry, and often contains residual unburned carbon and other components that can increase the AEA demand of a particular concrete …

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Leveraging Biomimicry And Additive Manufacturing To Improve Load Transfer In Brittle Materials, Ana Paula Bernardo

Graduate Theses and Dissertations

With the emergence of Additive Manufacturing (i.e., 3D printing) in construction, new strategically designed shapes can be created to improve load transfer through structural members and foundations. Cross-sections can be optimized to carry load using less material, or even using weaker constituent materials, like soils, which are cheap and abundant. The goal of this research is to investigate the benefits of using cellular patterns which leverage biomimicry in civil engineering applications, since nature has perfectly engineered materials and patterns which carry loads with the least amount of material possible. Most of the periodic cellular work to date has focused on …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

Performance Evaluation Of Lightweight Normal And Geopolymer Foamed Concrete Using Palm Oil Fuel Ash As Partial Replacement Of Binder, M .E. Alnahhal Ahmed

Student Works (2020-2029)

Carbon dioxide (CO2) emissions from Ordinary Portland Cement (OPC) have a detrimental effect on the environment and this had led many researchers to search for other alternatives in the form of sustainable cementitious materials. The depletion of natural resources and dumping the industrial by-products and waste materials are serious concern to our environment. This research focusses on the performance of using a palm oil industrial by-product, namely, palm oil fuel ash (POFA), as a partial replacement for OPC and fly ash (FA) in lightweight normal foamed concrete and lightweight geopolymer foamed concrete, respectively. Thus, using 10, 20, and 30% POFA …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Micro-Mechanical Analysis Of Corrosion Products Formed During Long-Term Carbonation Induced Corrosion Of Steel, Marijana Serdar, Dubravka Bjegovic, Valérie L’Hostis, Stéphane Poyet, Damien Féron

International Conference on Durability of Concrete Structures

During corrosion distinct types of corrosion products form, composed of different ratios of ferrous ions and oxide, hydroxides. Corrosion products have different physical and mechanical properties, mainly density, resistivity, volume and modulus of elasticity compared to iron. Knowing properties of corrosion products is indispensable for service life modelling of structures and can give valuable insight into the long-term corrosion propagation process. In this study micro-indentation method was used to evaluate mechanical properties of different layers formed during long-term carbonation induced corrosion of steel in concrete. Investigation was performed on three sets of reinforced concrete samples, that underwent corrosion during 50, …

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Experimental And Numerical Investigation On The Irregularity Of Carbonation Depth Of Concrete Under Supercritical Condition, Hao Bao Masc, Min Yu Dr., Jianqiao Ye Dr., Lihua Xu Dr., Yin Chi Dr., J Ye

International Conference on Durability of Concrete Structures

The heterogeneity of a cement-based material results in a random spatial distribution of carbonation depth, which may significantly affect the mechanical properties and durability of the material. Currently, there is a lack of both experimental and numerical investigations aiming at a statistical understanding of this important phenomenon. This paper presents both experimental and numerical supercritical carbonation test results of concrete blocks. The random fields of porosity and two-dimension random aggregate model of concrete were proposed for the simulation. The carbonation depths are measured and distributed along the carbonation boundary by the proposed rapid image processing technique, which are then statistically …

Guiding Principles In Developing The South African Approach To Durability Index Testing Of Concrete, Yunus Ballim, Mark Alexander

International Conference on Durability of Concrete Structures

Focused thinking on the possibility of early-age testing of concrete for long-term durability started in earnest during the late 1980’s in South Africa. Through sustained research, development and trial implementation on construction projects, three durability index (DI) tests have emerged, two of which have been adopted as national standard test methods for concrete construction, the remaining one being prepared a national standard. In this paper we review the guiding or foundational principles that directed the development of these DI tests, with a view to assessing the appropriateness and relevance of these guiding principles to modern concretes. The last 30 years …

The Influence Of Waste Glass Powder On The Chloride Binding Capacity Of Fly Ash/Cement Hardened Paste, Jh Yan, Tingyu Hao

International Conference on Durability of Concrete Structures

The potential of using waste glass powder to increase the chloride binding capacity of fly ash/cement hardened paste was investigated. When only fly ash replacing cement, the chloride binding capacity was raised within 28d when the fly ash replacement level was in the range from 30-50% by mass. But at a longer age of 60 to 90d, the binding performance was increased at the replacement level of 10-30wt%. The chloride binding capacity of glass powder-fly ash-cement system was increased by adding glass powder of 2% and 4% by mass at 7d while those at larger addition and longer age reduced. …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Data

Corresponding data set for Tran-SET Project No. 18STTAM01. Abstract of the final report is stated below for reference:

"This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Investigation Of Physical And Dynamic Properties Of High Porous Concrete, Ildar Akhmadullin

Publications

This project pursued two main objectives: (1) providing opportunities to Baton Rouge Community College (BRCC) students to develop hands-on laboratory skills and exposure to the transportation field, and (2) investigating porous concrete properties. Several BRCC student groups performed the work presented within this report; students prepared samples with different porosity and permeability according to standard specifications. The testing of the samples was performed at the Louisiana Transportation Research Center (LTRC) facility under the supervision of LTRC specialists. Findings indicate that the porosity of samples is backward proportional to the compression strength. This function is not linear but can be estimated …