Civil Engineering Commons^™

Observation Of Photovoltaic Effect And Single-Photon Detection In Nanowire Silicon Pn-Junction, Arief Udhiarto, Sri Purwiyanti, Daniel Moraru, Takeshi Mizuno, Michiharu Tabe

Makara Journal of Technology

We study nanowire silicon pin and pn-junctions at room and low temperature. Photovoltaic effects are observed for both devices at room temperature. At low temperature, nanowire pn-junction devices show their ability to detect single photon. This ability was not been observed for pin devices. Phosphorus-boron dopant cluster in the depletion region is considered to have the main role for single-photon detection capability. Fundamental mechanism of dopant-based single-photon detection in nanowire pn-junction is described in details.

Influences Of Surface Morphology Of Nanostructured Rutile Tio2 Nanorods/Nanoflowers As Photoelectrode On The Performance Of Dye-Sensitized Solar Cell, Mohd Khairul Bin Ahmad, Kenji Murakami

Makara Journal of Technology

Aligned Rutile TiO2 nanorods (r-TNRs) and TiO2 nanoflowers (r-TNFs) were successfully prepared by hydrothermal method. Using hydrochloric acid (HCl) as chelating agent and titanium butoxide (TBOT) as precursor, aligned r-TNRs with r-TNFs were successfully growth onto fluorine-doped tin oxide (FTO) with different morphologies. The influences of surface morphologies to the rutile based Dye-sensitized solar cell (DSC) efficiency are discussed. The highest lightto- electric energy conversion efficiency, 1.80% is achieved using different concentration under simulated solar light illumination of 100 mWcm-2 (1.5 AM).

Improvement In Performance Of Zno Based Dsc Prepared By Spraying Method, Rangga Winantyo, Devinda Liyanage, Kenji Murakami

Makara Journal of Technology

This paper reports the effect of TiCl4 on the performance of ZnO based DSC. ZnO was used due to its stability against photo-corrosion and photochemical properties similar to TiO2. Thin films of nanocrystalline ZnO were deposited on transparent conducting oxide glass using spray method. The ZnO films were treated using TiCl4. The cell’s efficiency was found to be 2.5% with TiCl4 post-treatment and 1.9% without TiCl4 post-treatment.

Determining The Air Gap Length Of An Axial Flux Wound Rotor Synchronous Generator, Abdul Multi, Iwa Garniwa, Uno Bintang Sudibyo

Makara Journal of Technology

The air gap length of the designed axial flux wound rotor (AFWR) synchronous generator is determined properly according to the design parameters. One of the distinct advantages of an axial flux (AF) machine is its adjustable air gap. An AF generator’s performance might be controlled by adjusting its air gap. The designed generator has a smallscale capacity that has 1 kW, 380 V, and 50 Hz. The windings are laid into slots made from laminated core. The slots are carved in the face of the stator and rotors. The generator has a single-double-sided slotted wound stator sandwiched between twin rotors. …

Production Optimization For Plan Of Gas Field Development Using Marginal Cost Analysis, Suprapto Soemardan, Widodo Wahyu Purwanto, Arsegianto Arsegianto

Makara Journal of Technology

Gas production rate is one of the most important variables affecting the feasibility plan of gas field development. It take into account reservoir characteristics, gas reserves, number of wells, production facilities, government take and market conditions. In this research, a mathematical model of gas production optimization has been developed using marginal cost analysis in determining the optimum gas production rate for economic profit, by employing the case study of Matindok Field. The results show that the optimum gas production rate is mainly affected by gas price duration and time of gas delivery. When the price of gas increases, the optimum …

Biodiesel Reactor Design With Glycerol Separation To Increase Biodiesel Production Yield, Budy Rahmat, Imas Siti Setiasih, Roni Kastaman

Makara Journal of Technology

The study consisted of reactor design used for transesterification process, effect of glycerol separation on transesterification reaction, determination of biodiesel quality, and mass balance analysis. The reactor was designed by integrating circulated pump/stirrer, static mixer, and sprayer that intensify the reaction in the outer tank reactor. The objective was to reduce the use of methanol in excess and to shorten the processing time. The results showed that the reactor that applied the glycerol separation was able to compensate for the decreased use of the reactant methanol from 6:1 to 5:1 molar ratio, and changed the mass balance in the product, …

Development Of Seebeck-Coefficient Measurement Systems Using Kelvin-Probe Force Microscopy, Kazutoshi Miwa, Faiz Salleh, Hiroya Ikeda

Makara Journal of Technology

Thermoelectric device is investigated by a number of researchers in order to enhance the thermoelectric efficiency. It is known that the efficiency can be improved by quantum effect. However, it is difficult to measure the thermoelectric characteristics of nanometer-scale structures. Thus a new measurement method is expected to be developed. We propose to apply Kelvin-probe force microscopy (KFM) to characterization of thermoelectric materials. KFM can locally observe surface potential of Fermi energy of a sample without touching the sample surface. In the present paper, we estimate the Seebeck coefficient of thin Si-on-insulator layers using KFM.

Agricultural Drought Pattern In West Java Using Thermal Vegetation Index From Modis-Terra Satellite, Dini Daruati, Rahmatulloh Rahmatulloh, Sri Hardiyanti Purwadhi

Makara Journal of Technology

This study examines agricultural drought paddy fields in West Java. The aims of this research are to know the pattern and distribution of paddy field drought in West Java and the correlation between drought and the physical characteristics. The agricultural drought is obtained from TVI (Thermal Vegetation Index) model. TVI is derived from MODIS Terra satellite image, which is the ratio between the LST (Land Surface Temperature) and EVI (Enhanced Vegetation Index). Physical factors studied are rainfall, l slope, geomorphology, soil drainage, and irrigation areas. The most severe drought occurred in September 2006 because of El Nino, covering 806,564 ha, …

Growth Of Crsi2 Nanostructures Using Crcl2 Powder On Si Substrates, Wen Li, Meng Erchao, Tomoji Matsushita, Shingo Oda, Daisuke Ishikawa, Kaito Nakane, Hirokazu Tatsuoka

Makara Journal of Technology

Chromium disilicide (CrSi2) nanostructures were grown by the exposure of Si (111) substrates to CrCl2 vapor in an argon gas flow at atmospheric pressure without using any metal catalyst. Dependence of the growth condition on the structural property was investigated. Hexagonal-shaped CrSi2 microrods were grown at 750 °C with 0.05 g of CrCl2. As the quantity of CrCl2 increased to 0.1 g, the bundle of CrSi2 nanowires with microrods and web-liked CrSi2 nanostructure with turning angles were grown at 750 °C and 700 °C, respectively. The preliminary discussion on the growth mechanism of CrSi2 micro- and nanostructures was carried out.

Biological Pretreatment Of Oil Palm Frond Fiber Using White-Rot Fungi For Enzymatic Saccharification, Euis Hermiati, Sita Heris Anita, Lucky Risanto, Dyah Styarini, Yanni Sudiyani, Achmad Hanafi, Haznan Abimanyu

Makara Journal of Technology

Oil palm frond is one type of lignocellulosic biomass abundantly and daily available in Indonesia. It contains cellulose which can be converted to glucose, and further processed to produce different kinds of value –added products. The aim of this research is to study the effects of biological pretreatment of oil palm frond (OPF) fiber using Phanerochaete chrysosporium and Trametes versicolor on the enzymatic saccharification of the biomass. The OPF fiber (40-60 mesh sizes) was inoculated with cultures of the two fungi and incubated at 27 °C for 4 weeks. The samples were taken after 1, 2, 3, and 4 weeks …

Electromagnetic Simulation For Thz Antenna-Coupled Microbolometers Operated At Room Temperature, Makoto Aoki, Masanori Takeda, Norihisa Hiromoto

Makara Journal of Technology

Room-temperature terahertz (THz) detectors with higher performance are necessary for utilizing the THz wave in various sensing, spectroscopy and imaging, but even the best ones in the present are still insufficient for the practical applications. This issue is essential especially in the region around 1 THz at which there exists a large technology gap between microwave and middle-infrared. Therefore, we study to develop an antenna-coupled microbolometer to achieve a high-performance THz detector operated at a room-temperature for sensing at around 1 THz frequency wave. In this paper, we present several important features and results obtained from electromagnetic simulations, which help …

Analysis Of Hole Lifetime In Soi Mosfet Single-Photon Detector, Dedy Septono Catur Putranto, Wei Du, Hiroaki Satoh, Atsushi Ono, Purnomo Sidi Priambodo, Djoko Hartanto, Hiroshi Inokawa

Makara Journal of Technology

Hole lifetime in the silicon-on-insulator (SOI) metal-oxide-semiconductor field-effect transistor (MOSFET) singlephoton detector was evaluated by the analysis of drain current histograms for different light intensities and substrate voltages. It was found that the peaks in the histogram corresponding to the larger number of stored holes grew as the gate bias decreased. This was attributed not to the increased light absorption efficiency or collection efficiency of the photo-generated holes, but to the prolonged hole lifetime presumably caused by the higher transverse electric field inside the body of SOI MOSFET.

Recognition System Of Indonesia Sign Language Based On Sensor And Artificial Neural Network, Endang Supriyati, Mohammad Iqbal

Makara Journal of Technology

Sign language as a kind of gestures is one of the most natural ways of communication for most people in deaf community. The aim of the sign language recognition is to provide a translation for sign gestures into meaningful text or speech so that communication between deaf and hearing society can easily be made. In this research, the Indonesian sign language recognition system based on flex sensors and an accelerometer is developed. This recognition system uses a sensory glove to capture data. The sensor data that are processed into feature vector are the 5-fingers bending and the palm acceleration when …

Performance Optimization Of Microbial Fuel Cell (Mfc) Using Lactobacillus Bulgaricus, Rita Arbianti, Tania Surya Utami, Heri Hermansyah, Deni Novitasari, Ester Kristin, Ira Trisnawati

Makara Journal of Technology

Electrical energy needs in Indonesia are expected to continue to rise. The use of petroleum as a source of energy still dominates, although oil reserves in Indonesia are increasingly being depleted. Therefore, there is a need to develop alternative sources of sustainable energy, such as microbial fuel cell (MFC). In this study, Lactobacillus bulgaricus was used as an electricity producer in a dual-chamber MFC reactor. We investigated the maximum electrical energy by varying the bacterial optical density (OD), the operational time of MFC, the reactor volume, the electrolyte solution, and the configuration of MFC reactor. In this study, the maximum …

Towards Rans Parameterization Of Vertical Mixing By Langmuir Turbulence In Shallow Coastal Shelves, Nityanand Sinha

USF Tampa Graduate Theses and Dissertations

Langmuir turbulence in the upper ocean is generated by the interaction between the wind-driven shear current and the Stokes drift velocity induced by surface gravity waves. In homogenous (neutrally stratified) shallow water, the largest scales of Langmuir turbulence are characterized by full-depth Langmuir circulation (LC). LC consists of parallel counter-rotating vortices aligned roughly in the direction of the wind. In shallow coastal shelves, LC has been observed engulfing the entire water column, interacting with the boundary layer and serving as an important mechanism for sediment re-suspension.

In this research, large-eddy simulations (LES) of Langmuir turbulence with full-depth LC in a …

Physico-Chemical, And Sensory Properties Of Soy Based Gouda Cheese Analog Made From Different Concentration Of Fat, Sodium Citrate And Various Cheese Starter Cultures, Abu Amar, Ingrid Suryanti Surono

Makara Journal of Technology

Gouda cheese analog (GCA) was made using soy protein isolate (SPI), skim milk powder (SMP), fat (palm fat and butter fat), and water (W) at optimal ratio of SPI : SMP : F : W = 14 : 6 : 20 : 60. The effects of butter fat, sodium citrate, and cheese starter culture on the sensory properties of ripened product were assessed by preference test, hedonic test, and the texture profile analysis (TPA) of GCA. The free fatty acids, water-soluble nitrogen, and reduction in pH value of progel were also measured. The use of 100% butter fat (BF) produced …

Effects Of Deposition Parameters And Oxygen Addition On Properties Of Sputtered Indium Tin Oxide Films, Badrul Munir, Rachmat Adhi Wibowo, Kim Kyoo Ho

Makara Journal of Technology

Indium tin oxide (ITO) films were sputtered on corning glass substrate. Oxygen admixture and sputtering deposition parameters were optimized to obtain the highest transparency as well as lowest resistivity. Structural, electrical and optical properties of the films were then examined. Increasing deposition rate and film thickness changed the crystallographic orientation from (222) to (400) and (440), as well as higher surface roughness. It was necessary to apply substrate heating during reposition to get films with better crystallinity. The lowest resistivity of 5.36 x 10-4 Ω•cm was obtained at 750 nm film thickness. The films’ resistivity was increased by addition of …

The Effect Of Rubber Mixing Process On The Curing Characteristics Of Natural Rubber, Abu Hasan, Rochmadi Rochmadi, Hary Sulistyo, Suharto Honggokusumo

Makara Journal of Technology

This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously …

Observation Of Center Disaster Damage On Pariaman And Wasior Using Differential Sar Interferometry (Dinsar), Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

This study focuses on disaster observations in Pariaman (West Sumatera) and Wasior (Papua) using remote sensing techniques (differential SAR interferometry). Differential interferometry (DInSAR) method was performed on two PALSAR data sets with different acquisition months, i.e. about a month after and before disaster, respectively. The center damage of Pariaman earthquake and Wasior flood can be determined by deriving Land Subsidence using DInSAR method.

Coastal Physical Vulnerability Of Surabaya And Its Surrounding Area To Sea Level Rise, Sayidah Sulma, Eko Kusratmoko, Ratna Saraswati

Makara Journal of Technology

The study for coastal vulnerability to sea level rise was carried out in Surabaya and its surrounding area, it has focused on calculations of the physical vulnerability index were used coastal vulnerability index (CVI) methods. It was standardized by the multi criteria analysis (MCA) approach according to the study area. The score of each physical variable derived from remote sensing satellite data and the results of studies that have been done, such as modeling results and thematic maps, and then integrated into geographic information systems (GIS). Result of this study shows that the coastal areas of Gresik, Surabaya, and Sidoarjo …

The Effect Of Size And Crumb Rubber Composition As A Filler With Compatibilizer Pp-G-Ma In Polypropylene Blends And Sir-20 Compound On Mechanical And Thermal Properties, Erna Frida

Makara Journal of Technology

Having been researched the development of thermoplastic elastomer material of polypropylene and natural rubber SIR- 20 compound with Crumb Rubber as the filler. Reinforced polypropylene with size 60 mesh with 1 mm, and the composition of the Crumb rubber (30, 40, and 50) wt%. Observed mechanical properties are tensile strength, fracture elongation, Young's modulus, tear strength and impact strength. Thermal properties are analyzed by DSC and DTA/TGA. It is acquired that for the size of 60 mesh crumb rubber tensile strength, fracture elongation, Young’s modulus, tear strength and impact strength are bigger than 1mm size. The addition of 60 mesh …

Development Of Local-Economic-Development Small And Medium Industries (Led-Sme) In East Java, Rachmad Hidayat, Sabarudin Akhmad

Makara Journal of Technology

This paper presents the effects of Indonesian government’s developmental efforts of assistance and training performed on the growth of LED-SME business units and business performance. Both parameters of the government’s assistance and training were used to analyze the impact to the growth and performance of business unit. To achieve a comprehensive result, samples acquired in this research were about 190 entrepreneurs and managers of LED-SME from East Java. Based on the parameters above, there are five hypotheses made to prove the relationship of the assistance and training to the growth and performance of business units. The structural equation modeling (SEM) …

Cdm Potential In Palm Solid Waste Cogeneration As An Alternative Energy In Aceh Province, Mahidin Mahidin, Izarul Machdar, Muhammad Faisal, Muhammad Nizar

Makara Journal of Technology

Empty Fruit Bunch (EFB) as a solid waste in Crude Palm Oil (CPO) industry does not utilized yet as an alternative energy source to generate electricity. It is well known that use of solid wate (biomass) as an energy source is part of the Clean Development Mechanism (CDM) scheme due to direct reduction of Green House Gases (GHGs) emission and provide a direct contribution to sustainable development. Utilization of EFB as a source of energy is very potential to be implemented in Aceh since this province has 25 CPO Mills at the moment which actively produce about 870,000 ton EFB …

Small Scale Experiment: Thermal Performance Comparison Between Fiber-Cement Roof And Photovoltaic Roof In Malang, Indonesia, Nurhamdoko Bonifacius, Sri Nastiti Nugrahani Ekasiwi

Makara Journal of Technology

Irradiation on the surface of photovoltaic module heats up the photovoltaic module itself and the room underneath the roof of integrated photovoltaic building in the tropics area. Room heating reduces thermal condition and photovoltaic module surface heating reduces its performance in generating electricity. This paper discusses an experiment of measuring the surface temperature of photovoltaic modules and fiber-cement roof surface as a comparison. This experiment also measures the impact of rising temperatures in each space underneath. It used small-scale mock-ups exposed to direct sunlight. The result of the experiment shows that photovoltaic roof surface temperature is lower than fiber-cement roof …

Improved Optical Probe For Measuring Phytoplankton Suspension Concentrations Based On Optical Fluoresensce And Absorption, Retno Wigajatri Purnamaningsih, Nining Betawati Prihantini

Makara Journal of Technology

This paper discusses the results of improved optical probe that works according to optical fluorescence and absorption phenomena for measuring the phytoplankton suspension concentrations. Measurements are made on the Scenedesmus sp. culture. The laboratory test has shown that range of concentration from 104 up to around 1 x 106 cells/mL; fluorescence intensity at λ = 685 nm; and logarithmic of transmission intensity at λ = 405 nm are proportional to the cell concentration linear with proportional constant γ = 4 × 10-5 and β = –2 × 10-7 mL/cell respectively.

Mechanical And Thermal Properties Of Polypropylene Reinforced By Calcined And Uncalcined Zeolite, Nurdin Bukit

Makara Journal of Technology

This study was carried out to compare mechanical and thermal properties of polypropylene (PP) reinforced with uncalcined and calcined zeolites. The PP samples were reinforced with zeolites at various quantities of 2, 4, and 6 (wt %). The comparison of the two types of zeolite was based on mechanical properties, including tensile strength, elongation at break, and Young’s modulus, and thermal characteristics analyzed using DSC, and DTA/TGA technique. The results obtained clearly revealed that both zeolites were able to significantly increase tensile strength and Young’s modulus of the samples, with calcined zeolite was found to work better. Addition of calcined …

Benchmark For Country-Level Earthquake Strong-Motion Instrumentation Program, Widjojo Adi Prakoso, I Nyoman Sukanta

Makara Journal of Technology

An empirical study to develop benchmark models at country-level to assess the suggested number of earthquake strongmotion stations based on a framework encompassing geographic, demographic, and socio-economic parameters is reported. The models are to provide a working estimate of the required number of stations for improving the strongmotion instrumentation program of Indonesia. National earthquake strong-motion networks of New Zealand, Japan, Taiwan, Iran, Turkey, and Italy were used as the references. The parameter proposed is the number of stations in land area of 1,000 km2, and three models based on the exponential regression analysis are presented as functions of population density, …

Worst Case Of Relative Disturbance Gain Array For Uncertain Distillation System, Rudy Agustriyanto, Jie Zhang

Makara Journal of Technology

This article discusses the constrained nonlinear optimization formulation for calculating the worst case of lower and upper bounds of relative disturbance gain array (RDGA) for uncertain process models. The proposed approach seeks the minimum and maximum values of the relative disturbance gains subject to the constraints in which the process and disturbance gains are within their uncertainty ranges. RDGA ranges are useful for control structure determination and the related robustness, as they provide information regarding the sensitivity to gain uncertainties. The proposed method is demonstrated by ternary distillation column case study. Closed loop simulation results support the analysis based on …

Biodiesel Production From Waste Cooking Oil Using Hydrodinamic Cavitation, Muhammad Dani Supardan, Satriana Satriana, Mahlinda Mahlinda

Makara Journal of Technology

The aim of this research was to study biodiesel production from low cost feedstock of waste cooking oil (WCO) using hydrodynamic cavitation apparatus. A two-step processes esterification process and transesterification process using hydrodynamic cavitation for the production of biodiesel from WCO is presented. The first step is acid-catalyzed esterification process for reducing free fatty acid (FFA) content of WCO and followed by base-catalyzed transesterification process for converting WCO to biodiesel as the second step. The result of esterification process with methanol to oil molar ratio of 5 and temperature of 60 oC showed that the initial acid value of WCO …

Knowledge Dictionary For Information Extraction On The Arabic Text Data, Wahyu Syaifullah Jauharis Saputra, Agus Zainal Arifin, Anny Yuniarti

Makara Journal of Technology

Information extraction is an early stage of a process of textual data analysis. Information extraction is required to get information from textual data that can be used for process analysis, such as classification and categorization. A textual data is strongly influenced by the language. Arabic is gaining a significant attention in many studies because Arabic language is very different from others, and in contrast to other languages, tools and research on the Arabic language is still lacking. The information extracted using the knowledge dictionary is a concept of expression. A knowledge dictionary is usually constructed manually by an expert and …