Civil Engineering Commons^™

Re-Evaluation Of Acceptance Testing Criteria For Structural Masonry Using The Prism Test Method, James Bristow

UNLV Theses, Dissertations, Professional Papers, and Capstones

The current acceptance criteria for structural masonry in accordance with International Building Code allows for the prism test method to be used. However, without a proper understanding of the effects of variable material properties such as individual masonry unit compressive strength and the various material moduli of elasticity, as well as the effect of field conditions on the unit’s performance, masonry prisms may “fail” to reach the design compressive strength (f’m).

By identifying causes of failure and evaluating the failure magnitude, it is concluded that when the masonry prism test method is utilized for acceptance testing of as-built masonry structures, …

High Early-Age Strength Concrete For Rapid Repair, Matthew O. Maler

UNLV Theses, Dissertations, Professional Papers, and Capstones

The aim of this research was to identify High Early-Age Strength (HES) concrete batch designs, and evaluate their suitability for use in the rapid repair of highways and bridge decks. To this end, two criteria needed to be met; a minimum compressive strength of 20.68 MPa (3000 psi) in no later than 12 hours, and a drying shrinkage of less than 0.06 % at 28 days after curing. The evaluations included both air-entrained, and non-air-entrained concretes.

The cement types chosen for this study included Type III and Type V Portland cement and “Rapid Set” − a Calcium Sulfoaluminate (CSA) cement. …

Encapsulation Process Of Propolis Extract By Casein Micelle Improves Sunscreen Activity, Muhamad Sahlan, Dara Dienayati, Darul Hamdi, Soraya Zahra, Heri Hermansyah, Malyn Chulasiri

Makara Journal of Technology

Propolis, a wax bee glue, have antioxidant activity and effective as broad spectrum UVB and UVA photoprotection sunscreens agent. To improve photoprotection activity in sunscreen cream, the propolis was encapsulated by casein micelle. The Indonesian propolis was extracted by ethanol and separated the wax by freeze precipitation. The extract was encapsulated by casein and reduced their size by ball mill homogenizer with the encapsulation efficiency about 80% and size of particles about 80 nm. The particles was applied in sunscreen cream, evaluate their stabillity and photoprotection activity Sun Protection Factor (SPF) spectrophotometer (Optometric 290s). The results shows that the selected …

Synthesis Of Libob Fine Powder To Increase Solubility, Etty Marti Wigayati, Titik Lestariningsih, Christin Rina Ratri, Ibrahim Purawiardi, Bambang Prihandoko

Makara Journal of Technology

Lithium bis (oxalate) borate or LiBOB compound has captured interest of researchers, because it is potentially viable to be used as electrolyte salt in lithium-ion battery system. This compound is easy to synthesize and considered to be more environmentally friendly compared to conventional electrolyte salt because LiBOB does not contain halogen element. This research focused on the synthesis of LiBOB fine powder, which main purpose is improving LiBOB salt solubility in liquid electrolyte solution. This will aid the ion transfer between electrodes which in turn will increase the electrolyte performance. Solid state reaction was employed in this experiment. Synthesis of …

A Plastic Design Method For Rc Moment Frame Buildings Against Progressive Collapse, Hadi Faghihmaleki

Makara Journal of Technology

In this study, progressive collapse potential of generic 3-, 8- and 12-storey RC moment frame buildings designed based on IBC-2006 code was investigated by performing non-linear static and dynamic analyses. It was observed that the model structures had high potential for progressive collapse when the second floor column was suddenly removed. Then, the size of beams required to satisfy the failure criteria for progressive collapse was obtained by using the virtual work method; i.e., using the equilibrium of the external work done by gravity load due to loss of a column and the internal work done by plastic rotation of …

In Vitro Toxicity Evaluation Of Caffeine Imprinted Polymer (Caf-Mip) For Decaffeination Method On Normal Chang Liver Cells, Fatimah Hashim, Faizatul Shimal Mehamod, Naizatul Akmal Nawi

Makara Journal of Technology

Over consuming of caffeine is one of the factors to a few health problems such as insomnia, hypertension and cardiovascular disease. This preliminary study was conducted to evaluate the Caffeine-Imprinted Polymer (CAF-MIP) toxicity that was synthesized for a new alternative method for decaffeination. It is crucial to evaluate the toxicity of CAF-MIPas this product is potential to be used as complimentary with any drinks containing caffeine. In this study, the CAF-MIP toxicity potential was confirmed on Normal Chang Liver cell (NCLC) based on its IC50 value andacridine orange and propidium iodide (AO/PI) staining for mode of cell death observation.Proliferation assay …

Nano-Channels Early Formation Investigation On Stainless Steel 316ti After Immersion In Molten Pb-Bi, Abu Khalid Rivai, Mardiyanto Mardiyanto, Annette Heinzel

Makara Journal of Technology

Development of fuel cladding and structural materials in Pb-Bi environment, especially at high temperature, is a critical issue for the deployment of LFR (Lead alloy-cooled Fast Reactor) and ADS (Accelerator Driven Transmutation System). This is because of the corrosive characteristic of Pb-Bi to metals as constituent materials of fuel cladding and structural of the reactors. Corrosion test of a high-chromium austenitic stainless steel i.e. SS316Ti in molten Pb-Bi at 550 ºC has been carried out for about 300 hours continuously. The characterization using SEM-EDS (Scanning Electron Microscopy - Energy Dispersive X-ray Spectroscopy) showed that an iron oxide as the outer …

Sorption And Ion Exchange Behaviour Of Natural Zeolite Packing, Chandra Wahyu Purnomo, Bernice Lenora, Wiratni Budhijanto, Hirofumi Hinode

Makara Journal of Technology

It is well known that zeolite is an efficient metal ions adsorbent. The excess charge of the zeolite building blocks i.e. (AlO4)-5 and (SiO4)-4 creating a negative surface charge that attract metal cations. Beside the surface charge, zeolite also has three dimensional pore structure and reasonably large surface area which also can be used as adsorption sites. Ease of cation uptake make it suitable for many process with adsorption and desorption application. This study was conducted to observe the sorption and ion exchange behaviour of zeolite-betonite rings toward iron and cobalt cations. The results shows that the adsorption patterns follow …

Influence Of Polyethylene Glycol (Peg) In Cmc-Nh4br Based Polymer Electrolytes: Conductivity And Electrical Study, Nur Khalidah Zainuddin, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried with new type and promising polymer electrolytes system by development of carboxyl methylcellulose (CMC) doped NH4Br and plasticized with polyethylene glycol (PEG). The sample was successfully prepared via solution casting with no separation phase and good mechanical properties. The electrical conductivity and thermal conductivity of CMC-NH4Br-PEG based PEs system have been measured by the electrical impedance spectroscopy method in the temperature range of 303–373 K. The highest ionic conductivity gained is 2.48 x 10-3 Scm-1 at ambient temperature for sample contain with 8 wt. % PEG. It can be concluded that the plasticized is accountable …

Purification Simulation With Vapor Permeation And Distillation-Adsorption In Bioethanol Plant, Misri Gozan, Mia Sari Setiawan, Kenny Lischer

Makara Journal of Technology

High purity of Bioethanol is required in biofuel mixing with gasoline (EXX). In bioethanol production line, the azeotropic property of ethanol-water becomes the barrier for purification process. This study examined two bioethanol separation processes by support of simulation tools, Superpro Designer 9.0 software. Ethanol purity and a low costeconomical process were the major considerations. Purification method of vapor permeation membrane technology was compared with distillation-adsorption method. Data from previous lab experiments and some literatures were used. The results showed that distillation-adsorption method is more economical compared to vapor permeation technology. Payback period of the simulation is 3.9 years and 4.3 …

Behavior And Strength Of Rc Spandrel Members Under Unsymmetrical Bending And Torsion Including Cfrp Retrofitting, Muhammad Fahim

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of an experimental and theoretical investigation of the behavior and strength of reinforced concrete spandrel members both with and without carbon fiber reinforced polymer (CFRP) retrofitting. Both isolated spandrel members with L-shaped cross section as well as those integrated with reinforced concrete slabs are studied. A series of isolated spandrel members were tested under separate and combined actions of unsymmetrical bending and torsion. Six of these specimens were retrofitted externally with high-strength CFRP strips. Materially nonlinear analysis procedures are also formulated and programmed for the spandrel members with and without CFRP retrofitting. Furthermore, ultimate bending-torsion …

Assessment Of Individual Photovoltaic Module Performance After 26 Years Of Field Exposure At The Telonicher Marine Lab In Trinidad, California, Jake Rada

Projects

In 1990, 192 ARCO M75 photovoltaic (PV) modules were installed as a part of the Schatz Solar Hydrogen Project at the Humboldt State University (HSU) Telonicher Marine Lab in Trinidad, California, within 150 m of the Pacific Ocean. This 9.2 kW-rated PV array was used to power the marine laboratory air compressor and an electrolyzer. Individual current-voltage (IV) curve tests were performed on each of the PV modules prior to the array’s construction in 1990 and again in 2001, 2010, and, most recently, in 2016, following decommissioning of the array. After 25.5 years of use, 188 of the original 192 …

Self-Sensing Cementitious Materials, Alexander Nicholas Houk

Theses and Dissertations--Civil Engineering

The study of self-sensing cementitious materials is a constantly expanding topic of study in the materials and civil engineering fields and refers to the creation and utilization of cement-based materials (including cement paste, cement mortar, and concrete) that are capable of sensing (i.e. measuring) stress and strain states without the use of embedded or attached sensors. With the inclusion of electrically conductive fillers, cementitious materials can become truly self-sensing. Previous researchers have provided only qualitative studies of self-sensing material stress-electrical response. The overall goal of this research was to modify and apply previously developed predictive models on cylinder compression test …

Restrained Shrinkage Of Fly Ash Based Geopolymer Concrete And Analysis Of Long Term Shrinkage Prediction Models, Md R. Islam, Mahbub K. Ahmed, Hosney Ara Begum, Erez N. Allouche

Journal of the Arkansas Academy of Science

The research presented in this manuscript describes the procedure to quantify the restrained shrinkage of geopolymer concrete (GPC) using ring specimen. Massive concrete structures are susceptible to shrinkage and thermal cracking. This cracking can increase the concrete permeability and decrease the strength and design life. This test is comprised of evaluating geopolymer concrete of six different mix designs including different activator solution to fly ash ratio and subjected to both restrained and free shrinkage. Test results obtained from this experimental setup was plotted along with the available empirical equation to observe the shrinkage strain of GPC and a model was …

Compact Facility For Testing Steady And Transient Thermal Performance Of Building Walls, Aimee Byrne, Gerard Byrne, Anthony Robinson

Articles

Energy efficiency retrofit of buildings represents a key effort in reducing EU energy demand by 20% by 2020. However, predictions tend to overestimate savings by large percentages. The shortfall in savings can be attributed to incorrect predictive techniques, comfort takeback along with other behavioural and workmanship variables. Common predictive techniques related to heat loss tend to be based on the U-value of the building envelope. This paper presents the design of a more straightforward and compact version of the traditional Hot-Box apparatus (measures U-value) which instead determines the thermal resistance of samples of building envelope. U-value includes the need to …

Polyvinyl Alcohol (Pva) Fiber-Reinforced Rubber Concrete And Rubberized Self-Compacting Concrete, Jiaqing Wang

Dissertations, Master's Theses and Master's Reports

This study experimentally investigates the mechanical performance and durability of Polyvinyl Alcohol (PVA) fiber-reinforced rubber concrete and the rubberized self-compacting concrete. The waste rubber particles were introduced as a partial replacement of fine aggregate in the plain concrete. In addition, the waste tire rubbers were pre-treated with alkali surface treatment method to enhance the performance. The PVA fibers were added to the concrete mixes to enhance the post-failure resistance and thus fracture energy. Rubberized fiber concrete samples were prepared with different fine aggregate replacement ratios and the optimum fiber content. At the same time, the rubber particles had been used …

Rubber Additives To Concrete Specimens, Kendall J. Sweitzer, Mary Mccannon

Williams Honors College, Honors Research Projects

Rubber, as an additive to concrete, would hypothetically cause a concrete specimen to take on some mechanical characteristics of the rubber to a certain degree. In particular, the concrete’s durability should increase when exposed to fluctuating temperature conditions due to the rubber additive. This experiment sets out to test crumb rubber as a concrete additive, cured under various atmospheric conditions. The effects shall be measured via a simple concrete compression test.

Unfortunately, several errors took place during experimental process that led to inconclusive results. However, it can be reasonably considered from testing Matrix One that the addition of crumb rubber …

Optimising The Performance Of Cement-Based Batteries, Aimee Byrne, Shane Barry, Niall Holmes Dr., Brian Norton

Articles

The development of a battery using different cement-based electrolytes to provide a low but potentially sustainable source of electricity is described. The current, voltage, and lifespan of batteries produced using different electrolyte additives, copper plate cathodes, and (usually) aluminium plate anodes were compared to identify the optimum design, components, and proportions to increase power output and longevity. Parameters examined include water/cement ratio, anode to cathode surface area ratio, electrode material, electrode spacing, and the effect of sand, aggregate, salts, carbon black, silica fume, and sodium silicate on the electrolyte. The results indicate that the greatest and longest lasting power can …

Optimizing Supply Chain Collaboration Based On Agreement Buyer-Supplier Relationship With Network Design Problem, Wahyudi Sutopo, Ayu Erliza, Arien Heryansyah

Makara Journal of Technology

In recent years, the rising competitive environment with shorter product life cycles and high customization forces industries to increase their flexibility, speed up their response, and enhance concurrent engineering designs. To integrate these prospects, supply chain collaboration becomes a pertinent strategy for industries to strengthen their competitiveness. The network design problem is used to implement supply chain collaboration. In the buying and selling process, sharing information between buyer and supplier are important to obtain a transaction decision. The optimimum supply chain profit can be identified by mathematical model of network design problem. The Mathematical Model takes into consideration the uncertainity …

Effect Of Milling On The Densification Of Sic-Basedcomposites From Polysilazane, Alfian Noviyanto, Toshiyuki Nishimura

Makara Journal of Technology

High density SiC-based composites from polysilazane were fabricated by high energy milling and hot pressing. After cross-linking at 200 °C, the polysilazane was pyrolysed at 1000 °C in N2 for 2 h to form amorphous Si-C-N-O followed by high energy milling for 1 h. Milled amorphous Si-C-N-O was sintered in hot pressing at 1600 and 1700 °C for 1 h in vacuum under the applied pressure of 50 MPa. Although no sintering additives were used, dense SiC-based composites were obtained with this method. Sintered density was 3.04 g/cm3, while only 2.57 g/cm3 for amorphous Si-C-N-O without milling. It is suggested …

Characterization And Utilization Of Calcium Oxide (Cao) Thermally Decomposed From Fish Bones As A Catalyst In The Production Of Biodiesel From Waste Cooking Oil, Aldes Lesbani, Sabat Okta Ceria Sitompul, Risfidian Mohadi, Nurlisa Hidayati

Makara Journal of Technology

Thermal decomposition of fish bones to obtain calcium oxide (CaO) was conducted at various temperatures of 400, 500, 800, 900, 1000, and 1100 °C. The calcium oxide was then characterized using X-ray diffractometer, FTIR spectrophotometer, and SEM analysis. The calcium oxide obtained from the decomposition at 1000 °C was then used as a catalyst in the production of biodiesel from waste cooking oil. Diffraction pattern of the calcium oxide produced from decomposition at 1000 °C showed a pattern similar to that of the calcium oxide produced by the Joint Committee on Powder Diffraction Standard (JCDPS). The diffractions of 2q values …

Thermoeconomic Optimization Of Cascade Refrigeration System Using Mixed Carbon Dioxide And Hydrocarbons At Low Temperature Circuit, Nasruddin Nasruddin, Arnas Arnas, Ahmad Faqih, Niccolo Giannetti

Makara Journal of Technology

Many applications and industrial processes require very low cooling temperature, such as cold storage in the biomedical field, requiring temperature below -80 °C. However, single-cycle refrigeration systems can only achieve the effective cooling temperature of -40 °C and, also, the performance of the cycle will decrease drastically for cooling temperatures lower than -35°C. Currently, most of cascade refrigeration systems use refrigerants that have ozone depletion potential (ODP) and global warming potential (GWP), therefore, in this study, a cascade system is simulated using a mixture of environmentally friendly refrigerants, namely, carbon dioxide and a hydrocarbon (propane, ethane or ethylene) as the …

Developing Road Infrastructure Route Planning: Increasing Feasibility Of Toll Road Project, Mohammed Ali Berawi, Teuku Yuri Zagloel, Perdana Miraj, Abdur Rohim Boy Berawi, Wellsi Titaheluw, Saipol Bari Bin Abd Karim

Makara Journal of Technology

Indonesian government attempts to improve connectivity and to increase regional activities in Sumatera Island through the development of Trans Sumatera Toll Road (TSTR). However, despite its benefits to local economic development in Sumatera, the project shows low feasibility due to a low amount of investment. It can be attributed from the lack of planning in the initial phase to produce a comprehensive route that considers the various potentials of the regions. Thus, this research aims to investigate alternative route planning of Trans Sumatera Toll Road particularly in this paper for Central Sumatera by studying Gross Regional Domestic Product (GRDP), population …

Thermal And -Γ –Ray Irradiation Effects On The Ionic Conductivity Of (Licl)X(Montmorillonite)1-X, Safei Purnama, Aziz Khan Jahja, Takeshi Sakuma

Makara Journal of Technology

Compositesof montmorillonite (MMT) - lithium salts have been prepared using a simple process of powders mixing followed by heating. The powders resulting from this method are expected to beionic conductors with a high ionic conductivity characteristics. This characteristics is also further improved by employing gamma-ray irradiation technique at specified irradiation doses. The best results were obtained for the (LiCl)0.5(MMT)0.5 composite with a room temperature ionic conductivity of 2.192 mS/cm, which then increases to ~5 mS/cm after gamma irradiation at a dose of 400 kGy. This value is equivalent to the value of the ionic conductivity of current commercial rechargeable lithium …

Design Of The Human Assembly Strategy In A Self-Optimizing Assembly Cell: A Case Study Of Indonesians, Novie Susanto, Ratna Purwaningsih, Kharisma Panca Kurniawati

Makara Journal of Technology

This paper presents a continuing study of the human cognitive aspect application in the technical systems. The last studies design a human-centered design based on the German culture. The result shows a significant difference of human performance between Germans and Indonesians. Therefore, this study examines the human cognitive model based on Indonesian culture to investigate whether the different cognitive model based on the culture aspect can improve the human performance. The study was conducted on 60 people classified by age, young (16-34 years old) and old (older than 34 years old). Participants render predictions on an assembly activity for two …

Expression And The Functional Study Of Fusion Proteins Α-Amylase And Hemolysin- Αas An Application In Biofilm Polysaccharide Degradation, Gede Yuda Sugiarta, Anggoro Wiseso, Siska Yuliana Sari, Etri Dian Kamila, Vanessa Geraldine, Diana Christina, Muhammad Hanifi, Dwiantari Satyapertiwi, Robby Hertanto, Budiman Bela, Masafumi Yohda, Muhamad Sahlan

Makara Journal of Technology

Biofilm is an aggregate of consortium bacteria that adhere to each other on a surface. It is usually protected by the exopolysaccharide layer. Various invasive medical procedures, such as catheterization, endotracheal tube installation, and contact lens utilization, are vulnerable to biofilm infection. The National Institute of Health (NIH) estimates 65% of all microbial infections are caused by biofilm. Periplasmic α-amylase (MalS) is an enzyme that hydrolyzes α-1, 4- glicosidic bond in glycogen, starch, and others related polysaccharides in periplasmic space. Another protein called hemolysin-α (HlyA) is a secretion signal protein on C terminal of particular peptide in gram negative bacteria. …

Influence Of Concrete Compressive Strength On Transfer And Development Lengths Of Prestressed Concrete, Alberto Teodoro Ramirez-Garcia

Graduate Theses and Dissertations

This research examines the relationship between concrete compressive strength and strand bond. The goal of this research was to develop an equation that relates strand bond to concrete compressive strength at strand release (approximately 1 day of age) and at 28 days of age, and those equations are presented in this investigation. Strand bond is assessed by measuring the transfer length and development length for prestressed beams cast in the laboratory. In the U.S., strand bond is predicted using transfer length and development length equations provided by the American Concrete Institute (ACI-318) Building Code and American Association of State and …

The Influence Of Alkalinity Of Portland Cement On The Absorption Characteristics Of Superabsorbent Polymers (Sap) For Use In Internally Cured Concrete, Juan D. Tabares Tamayo

Open Access Theses

The concrete industry increasingly emphasizes advances in novel materials that promote construction of more resilient infrastructure. Due to its potential to improve concrete durability, internal curing (IC) of concrete by means of superabsorbent polymers (SAP) has been identified as one of the most promising technologies of the 21st century. The addition of superabsorbent polymers into a cementitious system promotes further hydration of cement by providing internal moisture during the hardening and strength development periods, and thus limits self-desiccation, shrinkage, and cracking.

This thesis presents the work performed on the series of cement pastes with varying alkalinity of their pore solutions …

Bridge Maintenance To Enhance Corrosion Resistance And Performance Of Steel Girder Bridges, Luis M. Moran Yanez

Open Access Dissertations

The integrity and efficiency of any national highway system relies on the condition of the various components. Bridges are fundamental elements of a highway system, representing an important investment and a strategic link that facilitates the transport of persons and goods. The cost to rehabilitate or replace a highway bridge represents an important expenditure to the owner, who needs to evaluate the correct time to assume that cost. Among the several factors that affect the condition of steel highway bridges, corrosion is identified as the main problem. In the USA corrosion is the primary cause of structurally deficient steel bridges. …

Sulfate Resistance Of Nanosilica Contained Portland Cement Mortars, Iani Batilov Batilov

UNLV Theses, Dissertations, Professional Papers, and Capstones

Soils, sea water and ground water high in sulfates are commonly encountered hostile environments that can attack the structure of concrete via chemical and physical mechanisms which can lead to costly repairs or replacement. Sulfate attack is a slow acting deteriorative phenomenon that can result in cracking, spalling, expansion, increased permeability, paste-to-aggregate bond loss, paste softening, strength loss, and ultimately, progressive failure of concrete. In the presented research study, Portland cement (PC) mortars containing 1.5% to 6.0% nanosilica (nS) cement replacement by weight were tested for sulfate resistance through full submersion in sodium sulfate to simulate external sulfate attack. Mortars …