Civil Engineering Commons^™

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Influence Of Glass Fiber Reinforced Polymer Wraps On Corrosion Progression Of Bridge Piles In Marine Environments, Shayan Yazdani

USF Tampa Graduate Theses and Dissertations

The Friendship Trail Bridge connecting Tampa to St. Petersburg was demolished in 2016. Thirteen 20 inches. by 20 inches. reinforced concrete piles supporting its superstructure were part of research studies conducted between 2004 and 2008 to explore the role of glass fiber reinforced polymers (GFRP) in corrosion repair. During demolition, piles were typically cut at the pile cap and in the splash zone. The resulting segments varied in length between 3 to 4 ft. These remnants were transported to the University of South Florida (USF) campus for postmortem analysis. The overarching goal was to establish the role of GFRP in …

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, aimed to produce a sustainable asphalt pavement using green technology, has been studied in the past two decades. Technologies including encapsulated rejuvenator and induction heating have been proposed, demonstrated in the laboratory, and gradually evaluated in field application. This paper looks into the synergy effect of the above two technologies, where induction heating serves as the asphalt damage repair mechanism, requiring just 2 min heating time and encapsulated rejuvenator will replenish (rejuvenate) aged asphalt binder and reinstate bitumen’s healing ability. Moreover, the increased temperature from induction heating could in turn accelerate the diffusion process of rejuvenator into aged …

Low-Grade Kaolin Clay Natural Resource For Use As A Supplementary Cementitious Material In Structural Concrete Elements, Brandon X. Lorentz

USF Tampa Graduate Theses and Dissertations

At the turn of the century, low-grade kaolin clay (LGK) was presented as a widely available and potential natural resource of supplementary cementitious materials (SCM) for producing high performance concretes. In using LGK as an SCM, clinker production is reduced, aiding environmental concerns with associated CO2 emissions. These types of clays have very heterogeneous mineralogy and microstructural characteristics, causing unique influences on concrete structural and flow performance, although these influences are not well understood. This research studies LGK natural to the state of Florida and assesses their potential use as high performance SCM.

Ten kaolin clays were obtained through a …

Performance Evaluation Of Lightweight Normal And Geopolymer Foamed Concrete Using Palm Oil Fuel Ash As Partial Replacement Of Binder, M .E. Alnahhal Ahmed

Student Works (2020-2029)

Carbon dioxide (CO2) emissions from Ordinary Portland Cement (OPC) have a detrimental effect on the environment and this had led many researchers to search for other alternatives in the form of sustainable cementitious materials. The depletion of natural resources and dumping the industrial by-products and waste materials are serious concern to our environment. This research focusses on the performance of using a palm oil industrial by-product, namely, palm oil fuel ash (POFA), as a partial replacement for OPC and fly ash (FA) in lightweight normal foamed concrete and lightweight geopolymer foamed concrete, respectively. Thus, using 10, 20, and 30% POFA …

Studying The Effects Of Various Process Parameters On Early Age Hydration Of Single- And Multi-Phase Cementitious Systems, Rachel Cook

Doctoral Dissertations

”The hydration of multi-phase ordinary Portland cement (OPC) and its pure phase derivatives, such as tricalcium silicate (C₃S) and belite (ß-C₂S), are studied in the context varying process parameters -- for instance, variable water content, water activity, superplasticizer structure and dose, and mineral additive type and particle size. These parameters are studied by means of physical experiments and numerical/computational techniques, such as: thermodynamic estimations; numerical kinetic-based modelling; and artificial intelligence techniques like machine learning (ML) models. In the past decade, numerical kinetic modeling has greatly improved in terms of fitting experimental, isothermal calorimetry to kinetic-based modelling …

Strengthening Of Corroded Steel Structures Using Cfrp – An Experimental Review, Ghada El-Mahdy Ph.D., P.Eng, Abdallah H. Yassin, Abdel El Rahman Khaled

Civil Engineering

Fibre reinforced polymers (FRP) have been widely used to strengthen reinforced concrete structures, however, nowadays their use to strengthen steel structures is under investigation. In particular, the need to strengthen corroded steel structures found in aggressive environments, such as marine environments, which have undergone a reduction in cross-sectional area and hence a reduction in their load-carrying capacity is in need of studying. The main problems that arise when using carbon fibre reinforced polymer (CFRP) sheets to strengthen steel structures is the weakness in the interfacial bond between the CFRP and the steel surface, the thinness of CFRP sheet, and the …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …

Influence Of Nh4f In Dextran Based Biopolymer Electrolytes: Conductivity And Electrical Analysis, Muhamad Hafiz Hamsan, Mohd Fakhrul Zamani Kadir, Shujahadeen Bakar Aziz, Muhammad Amirul Solihin Azha, Saifful Kamaluddin Muzakir

Makara Journal of Technology

Dextran polymer host was doped with different concentrations of ammonium fluoride (NH4F) via casting technique. In this present work, dextran-NH4F film has been employed to investigate the ionic conductivity using electrochemical impedance spectroscopy from 50 to 5 MHz. The highest room temperature conductivity is achieved at (2.33 ± 0.76) × 10-3 S cm-1 with 40 wt.% NH4F. The electrolyte is found to obey Arrhenius rule at high temperature with activation energy of 0.21 eV. Dielectric analysis has been performed to obtain better understanding on the conductivity pattern. The dielectric parameters e.g. ɛreal, ɛimag, Mreal, and Mimag have been tested as …

Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman

Makara Journal of Technology

Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …

Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani

Makara Journal of Technology

Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …

Multiscale Modeling Of Fracture In Quasi-Brittle Materials Using Bifurcation Analysis And Element Elimination Method, Keyvan Zare Rami

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Analyzing the fracture of heterogeneous materials is a complex problem, due to the fact that the mechanical behavior of a heterogeneous material is strongly dependent on a variety of factors, such as its microstructure, the properties of each constituent, and interactions between them. Therefore, these factors must be effectively taken into account for accurate analysis, for which the multiscale method has been widely used. In this scheme, the computational homogenization method is used to obtain the effective macroscopic properties of a heterogeneous material based on the response of a Representative Volume Element (RVE). The growth of damage in an RVE …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Micro-Mechanical Analysis Of Corrosion Products Formed During Long-Term Carbonation Induced Corrosion Of Steel, Marijana Serdar, Dubravka Bjegovic, Valérie L’Hostis, Stéphane Poyet, Damien Féron

International Conference on Durability of Concrete Structures

During corrosion distinct types of corrosion products form, composed of different ratios of ferrous ions and oxide, hydroxides. Corrosion products have different physical and mechanical properties, mainly density, resistivity, volume and modulus of elasticity compared to iron. Knowing properties of corrosion products is indispensable for service life modelling of structures and can give valuable insight into the long-term corrosion propagation process. In this study micro-indentation method was used to evaluate mechanical properties of different layers formed during long-term carbonation induced corrosion of steel in concrete. Investigation was performed on three sets of reinforced concrete samples, that underwent corrosion during 50, …

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Experimental And Numerical Investigation On The Irregularity Of Carbonation Depth Of Concrete Under Supercritical Condition, Hao Bao Masc, Min Yu Dr., Jianqiao Ye Dr., Lihua Xu Dr., Yin Chi Dr., J Ye

International Conference on Durability of Concrete Structures

The heterogeneity of a cement-based material results in a random spatial distribution of carbonation depth, which may significantly affect the mechanical properties and durability of the material. Currently, there is a lack of both experimental and numerical investigations aiming at a statistical understanding of this important phenomenon. This paper presents both experimental and numerical supercritical carbonation test results of concrete blocks. The random fields of porosity and two-dimension random aggregate model of concrete were proposed for the simulation. The carbonation depths are measured and distributed along the carbonation boundary by the proposed rapid image processing technique, which are then statistically …

Guiding Principles In Developing The South African Approach To Durability Index Testing Of Concrete, Yunus Ballim, Mark Alexander

International Conference on Durability of Concrete Structures

Focused thinking on the possibility of early-age testing of concrete for long-term durability started in earnest during the late 1980’s in South Africa. Through sustained research, development and trial implementation on construction projects, three durability index (DI) tests have emerged, two of which have been adopted as national standard test methods for concrete construction, the remaining one being prepared a national standard. In this paper we review the guiding or foundational principles that directed the development of these DI tests, with a view to assessing the appropriateness and relevance of these guiding principles to modern concretes. The last 30 years …

The Influence Of Waste Glass Powder On The Chloride Binding Capacity Of Fly Ash/Cement Hardened Paste, Jh Yan, Tingyu Hao

International Conference on Durability of Concrete Structures

The potential of using waste glass powder to increase the chloride binding capacity of fly ash/cement hardened paste was investigated. When only fly ash replacing cement, the chloride binding capacity was raised within 28d when the fly ash replacement level was in the range from 30-50% by mass. But at a longer age of 60 to 90d, the binding performance was increased at the replacement level of 10-30wt%. The chloride binding capacity of glass powder-fly ash-cement system was increased by adding glass powder of 2% and 4% by mass at 7d while those at larger addition and longer age reduced. …

Alkali Reactive Carbonate Rocks: Is It Alkali Silica Reaction (Asr) Or Alkali Carbonate Reaction (Acr)?, Mengesha Beyene, Rc Meininger

International Conference on Durability of Concrete Structures

The root cause of distress in two different concrete structures made from carbonate coarse aggregates that fit the textural and compositional criteria cited for ACR was found to be caused by ASR, not ACR. Stereo-optical examination and transmitted polarized light microscopy (PLM) analysis showed that the concretes contain some dark gray, fine-grained argillaceous dolomitic coarse aggregates in which secondary white deposit filling the cracks extending from these aggregates into the paste (as well as lining air voids) is ASR gel. Back scattered electron (BSE) imaging with EDS spectra and x-ray elemental mappings, clearly confirm that the white secondary deposits consist …

Thermo-Oxidative Degradation Of Hdpe Geomembranes: Effect Of Phenolic Antioxidant And Hindered Amine Light Stabilizer Concentrations, Yasin Kocak

USF Tampa Graduate Theses and Dissertations

High density polyethylene (HDPE) geomembrane is most common geomembrane which is mainly used for civil engineering applications. However, HDPE geomembrane loses its properties under oxidative degradation progress. This study aims to assess geomembranes which have different percentage of phenolic antioxidant and hindered amine light stabilizer (HALS) with under the six months of the thermal-oxidative degradation. The interactions between phenolic antioxidant, HALS and carbon black can affect the mechanical, physical and chemical properties. To monitor these properties, Differential Scanning Calorimetry (DSC), Fourier-transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Scanning Electron Microscopy coupled with Energy Dispersive X-ray spectroscopy (SEM/EDX), Melt Index tests, …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Data

Corresponding data set for Tran-SET Project No. 18STTAM01. Abstract of the final report is stated below for reference:

"This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …