Civil and Environmental Engineering Commons^™

Modeling Of A New Structure Of Precision Air Conditioning System Using Secondary Condenser For Rh Regulation, Aries Subiantoro, Nasruddin Nasruddin, Feri Yusivar, Muhammad Idrus Al-Hamid, Bagio Budiardjo

Makara Journal of Technology

A dynamic mathematical model for a new structure of precision air conditioning (PAC) has been developed. The proposed PAC uses an additional secondary condenser for relative humidity regulation compared to a basic refrigeration system. The work mechanism for this system and a vapour-compression cycle process of the system are illustrated using psychrometric chart and pressure-enthalpy diagram. A non-linear system model is derived based on the conservation of mass and energy balance principles and then linearized at steady state operating point for developing a 8th-order state space model suited for multivariable controller design. The quality of linearized model is analyzed in …

Canopy Radiation Transmission For An Energy Balance Snowmelt Model, Vinod Mahat, David G. Tarboton

Civil and Environmental Engineering Faculty Publications

To better estimate the radiation energy within and beneath the forest canopy for energy balance snowmelt models, a two stream radiation transfer model that explicitly accounts for canopy scattering, absorption and reflection was developed. Upward and downward radiation streams represented by two differential equations using a single path assumption were solved analytically to approximate the radiation transmitted through or reflected by the canopy with multiple scattering. This approximation results in an exponential decrease of radiation intensity with canopy depth, similar to Beer's law for a deep canopy. The solution for a finite canopy is obtained by applying recursive superposition of …

Finite Element Modeling Of Seismic Wave Propagation In Earthen Embankments, Binyam Tadese

Electronic Theses and Dissertations

The detection of internal seepage zones in embankments (dams and levees) by geophysical seismic techniques such as seismic refraction is limited by a number of factors. Some factors are associated with inversion and smoothing problems during processing, while others are associated with the natural characteristics of embankments and seepage anomalies. In this research, changes in the seismic response associated with: embankment soil compositions and moisture, characteristics of the seepage zone, presence of water in the reservoir, and shape of embankment was studied via 2D and 3D finite element (FE) embankment models. Artificial reflections from external boundaries and numerical dispersion were …

Development Of A Structured Concrete Thermocline Thermal Energy Storage System, Bradley M. Brown

Graduate Theses and Dissertations

The past couple of decades have shown a concern when considering the way the world obtains its power. The focus has been switching from fossil fuels that have been used for hundreds of years to renewable energy sources, such as the sun. Solar energy is readily and infinitely available for harnessing. One problem with solar energy, though, is its inability to be used during the night time and during cloud covered weather. A solution to this problem is the use of energy storage mechanisms. For solar plants that use solar thermal energy (concentrating solar power plants), thermal energy storage (TES) …

Determining Transverse Design Forces For A Next-D Bridge Using 3d Finite Element Modeling, Robert Funcik

All Theses

This thesis looks into the use of 3D Finite Element Modeling to determine the transverse design forces for short-span bridges built using the Northeast Extreme Tee with integral deck (NEXT-D) beam. Models were built using either solid elements or shell elements to represent the bridge deck, and the results were compared. The stiffness of the shear keys were taken into account during the modeling process. Results were compared to the AASHTO strip width method for design bridge decks, and the results showed that the strip width method would not be adequate for the design of NEXT-D bridges, so specific live …

Hexahedral Mesh Refinement Using An Error Sizing Function, Gaurab Paudel

Theses and Dissertations

The ability to effectively adapt a mesh is a very important feature of high fidelity finite element modeling. In a finite element analysis, a relatively high node density is desired in areas of the model where there are high error estimates from an initial analysis. Providing a higher node density in such areas improves the accuracy of the model and reduces the computational time compared to having a high node density over the entire model. Node densities can be determined for any model using the sizing functions based on the geometry of the model or the error estimates from the …

Dye Waste Treatment, Siew Teng Ong, Pei Sin Keng, Weng Nam Lee, Sie Tiong Ha, Yung Tse Hung

Civil and Environmental Engineering Faculty Publications

© 2011 by the authors. Dye wastes represent one of the most problematic groups of pollutants because they can be easily identified by the human eye and are not easily biodegradable. This literature review paper highlights and provides an overview of dye waste treatments performed over the three years period from 2008-2010. Noteworthy processes for the treatment of dye waste include biological treatment, catalytic oxidation, filtration, sorption process and combination treatments.

Use Of Innovative Computer Technology And Optical Texture Properties In The Analysis Of Pavement Digital Images, Saumya Priyadari Amarasiri

USF Tampa Graduate Theses and Dissertations

Digital image based automated pavement crack detection and classification technology has seen vast improvements in the recent years. In spite of these developments, although pavement crack lengths and widths can be evaluated using state-of-the-art software with a reasonable accuracy, no reported evidence is found in extending this technology to evaluate crack depths. Hence a preliminary study was carried out to model the digital image formation of cracked concrete pavements based on the Bidirectional Reflection Distribution Function. It was revealed that a definitive theoretical relationship exists among the crack widths and depths and the maximum pixel intensity contrasts in the images …

A Numerical And Experimental Study Of Differential Settling In Cohesive Sediment, Chad Heiliger

All Theses

Accurate sedimentation modeling has important applications in a number of fields. This includes modeling the accumulation of sediment in harbor channels and modeling the sedimentation and accumulation of particles in retention ponds in the still waters behind dams in order to calculate the trap efficiency. By accurately modeling sedimentation, engineering failures such as the 2008 TVA spill at the Kingston Fossil Plant could possibly be avoided. Three different numerical models comparing the settling rates of individual particles in quiescent waters were created to compare the change of settling velocity due to particle size distributions, change of local concentrations, and flocculation …

Plant Growth Modeling Using L-System Approach And Its Visualization, Atris Suyantohadi, Alfiyan Alfiyan, Mochamad Hariadi, Mauridhi Hery Purnomo

Makara Journal of Technology

The visualization of plant growth modeling using computer simulation has rarely been conducted with Lindenmayer System (L-System) approach. L-System generally has been used as framework for improving and designing realistic modeling on plant growth. It is one kind of tools for representing plant growth based on grammar sintax and mathematic formulation. This research aimed to design modeling and visualizing plant growth structure generated using L-System. The environment on modeling design used three dimension graphic on standart OpenGL format. The visualization on system design has been developed by some of L-System grammar, and the output graphic on three dimension reflected on …

Implications Of Climate-Driven Variability And Trends For The Hydrologic Assessment Of The Reynolds Creek Experimental Watershed, Idaho, V. Sridhar, Anurag Nayak

Civil Engineering Faculty Publications and Presentations

The Soil and Water Assessment Tool (SWAT) model was used to assess the implications of long-term climate trends for the hydroclimatology of the Reynolds Creek Experimental Watershed (RCEW) in the Owyhee Mountains, Idaho of the Intermountain West over a 40- year period (1967-2006). Calibration and validation of the macroscale hydrology model in this highly monitored watershed is key to address the watershed processes that are vulnerable to both natural climate variability and climate change and . The model was calibrated using the streamflow data collected between 1997 and 2006 from the three nested weirs, the Reynolds Mountain East (RME) , …

Hydrodynamic Modeling Of San Elijo Lagoon, California, Mary Elizabeth Nee Friedmann Bourgoyne

LSU Master's Theses

Decisions on where to concentrate management efforts need to be guided by an ability to accurately simulate and predict physical and ecological changes. Many restoration projects experience difficulties due to a lack of understanding of the ecological response and evolution of wetland systems (Goodwin et al., 2001). There are several approaches that can be taken in analyzing a system. The appropriate selection should be based on the available data, the spatial scale of the wetland, and the physical processes governing the system (Goodwin and Kamman, 2001). Predictive tools are essential for good long-term management (Goodwin et al., 2001). The objective …

Slides: Groundwater Declines, Climate Change And Approaches To Adaptation, Katharine Jacobs

Western Water Law, Policy and Management: Ripples, Currents, and New Channels for Inquiry (Martz Summer Conference, June 3-5)

Presenter: Katharine Jacobs, Director of the Arizona Water Institute, University of Arizona

37 slides

Stochastic Spatio-Temporal Uncertainty In Gis-Based Water Quality Modeling Of The Land Water Interface, Ahmad Mohamad Salah

Theses and Dissertations

Integrated water resources management has been used for decades in various formats. The limited resources and the ever growing population keep imposing pressure on decision makers to better-, and reliably, manage the available waters. On the other hand, the continuous development in computing and modeling power has helped modelers and decision makers considerably. To use these models, assumptions have to be made to fill in the gaps of missing data and to approximate the current conditions. The type and amount of information available can also be used to help select the best model from the currently available models. Advances in …

Assessing Water Quality Modeling In Subtropical Regions Based On A Case Study Of The Aguamilpa Reservoir, Oliver Obregon

Theses and Dissertations

The shortage of water in Mexico has made public and private institutions look at reservoirs as an alternative solution for present and future water supply. However, eighty percent of the existing reservoirs in Mexico are contaminated at some level, many severely. Water quality models are water-management tools used to diagnose water quality problems and the impact of various environmental conditions. They can be effective in assessing various measures of remediation leading to improved water quality. In most of the cases such water quality models have been successfully applied in reservoirs located in temperate climates. However, the use of water quality …

Parallel Processing Of Reactive Transport Models Using Openmp, Jared D. Mclaughlin

Theses and Dissertations

Transport codes are beginning to be parallelized in order to allow more complex add-ons, such as geochemical packages, to utilize finer, more accurate grids, and to reduce solution times making stochastic and Monte Carlo simulations more feasible. Most codes parallelized via MPI (message passing interface) offer good results, but require the development of a new parallel code. OpenMP, the shared-memory standard, offers incremental parallelization, allowing sequential codes to remain relatively intact with minimal changes or additions. OpenMP allows speedup to be seen on personal computers with dual processors or greater, unlike some other parallelization approaches that require a supercomputer. An …

Physical Modeling Of Flow And Sediment Transport Using Distorted Scale Modeling, Ryan L. Waldron

LSU Master's Theses

As coastal Louisiana's land loss problem continues to grow unabated, many different solutions have been proposed. One such solution is the concept of diverting fresh water and sediment from the river into the coastal wetlands. Louisiana State University has a Small Scale Physical Model (SSPM) for the study of the potential of such diversions; it is deisgned to study the bulk movement of sediment in the river and diversions. The model is a distorted scale model with a horizontal scale of 1:12,000 and a vertical scale of 1:500; this extreme distortion has brought into question the applicability of the model. …

Fate And Transport Of Microorganisms In Coastal Subsurface-Experiment And Modeling, Haibo Cao

LSU Doctoral Dissertations

The objective of this dissertation was to investigate the fate and transport of microorganisms in coastal subsurface. Two topics were studied: (1) evaluation of the performance of the Marshland Upwelling System (MUS) in removing fecal bacteria and the background recovery after it is shut down; (2) Investigation of the effects of salinity and soluble organic matter (SOM) on sorption of MS-2 and development of a model to describe the sorption and transport process. The MUS showed effective performance in removing fecal bacteria during its 32 month operation period at Bayou Segnette Site. The removal efficiency was increased with its operation …

Shear Modulus Degradation Of Liquefying Sand: Quantification And Modeling, Peter A. Olsen

Theses and Dissertations

A major concern for geotechnical engineers is the ability to predict how a soil will react to large ground motions produced by earthquakes. Of all the different types of soil, liquefiable soils present some of the greatest challenges. The ability to quantify the degradation of a soil's shear modulus as it undergoes liquefaction would help engineers design more reliably and economically. This thesis uses ground motions recorded by an array of downhole accelerometers on Port Island, Japan, during the 1995 Kobe Earthquake, to quantify the shear modulus of sand as it liquefies. It has been shown that the shear modulus …

Integrated Modeling Of Nitrate Contamination Of Groundwater In Agriculture-Dominated Watersheds, M. Almasri, Jagath J. Kaluarachchi

Civil and Environmental Engineering Faculty Publications

This paper presents and implements a framework for modeling the impact of land use practices and protection alternatives on nitrate pollution of groundwater in agricultural watersheds. The framework utilizes the national land cover database (NLCD) of the United State Geological Survey (USGS) grid and a geographic information system (GIS) to account for the spatial distribution of on-ground nitrogen sources and corresponding loadings. The framework employs a soil nitrogen dynamic model to estimate nitrate leaching to groundwater. These estimates were used in developing a groundwater nitrate fate and transport model. The framework considers both point and non-point sources of nitrogen across …

An Investigation Of Size Exclusion And Diffusion Controlled Membrane Fouling, Colin Michael Hobbs

Electronic Theses and Dissertations

The reduction of membrane productivity (i.e. membrane fouling) during operation occurs in virtually all membrane applications. Membrane fouling originates from the method by which membranes operate: contaminants are rejected by the membrane and retained on the feed side of the membrane while treated water passes through the membrane. The accumulation of these contaminants on the feed side of the membrane results in increased operating pressures, increased backwashing frequencies, increased chemical cleaning frequencies, and increased membrane replacement frequencies. The most significant practical implication of membrane fouling is increased operating and maintenance costs. As such, membrane fouling must be properly managed to …

3d Laser Scanning & Modeling System, Purdue Ect Team

ECT Fact Sheets Archive

Traditional methods of measuring and modeling the surface geometry of large, complex structures or sites that require engineering or survey-grade accuracy are often inaccurate, incomplete or expensive. Inaccurate or incomplete drawings and models often lead to costly construction errors or delays. A portable, auto-scanning laser and PC system that lets users economically obtain accurate, complete, and timely as-built geometry information for large structures and sites. The system can remotely measure natural surfaces up to 100m away at the speed of 800 points per second. With spacing between adjacent points as fine as 1mm, users can capture an extremely high level …

Modeling The Effective Elastic Modulus Of Rc Beams Exposed To Fire, Jui-Hsiang Hsu, Cherng-Shing Lin, Chang-Bin Huang

Journal of Marine Science and Technology–Taiwan

This work combines thermal and structural analyses to study the effect of fire on the elastic modulus of reinforced concrete beams. The thermal analysis uses the finite difference method to model the temperature distribution of a reinforced concrete beam maintained at high temperature. The structural analysis, using the lumped method, is utilized to calculate the effective elastic modulus of reinforced concrete beams. The results of the thermal analysis are compared to the experimental results in the literature, and the analytically derived structural results are also compared with experimental data on the flexural behaviors of RC beams exposed to fire. The …

A Three-Dimensional Bay/Estuary Model To Simulate Water Quality Transport, Jing Yu

Electronic Theses and Dissertations

This thesis presents the development of a numerical water quality model using a general paradigm of reaction-based approaches. In a reaction-based approach, all conceptualized biogeochemical processes are transformed into a reaction network. Through the decomposition of species governing equations via Gauss-Jordan column reduction of the reaction network, (1) redundant fast reactions and irrelevant kinetic reactions are removed from the system, which alleviates the problem of unnecessary and erroneous formulation and parameterization of these reactions, and (2) fast reactions and slow reactions are decoupled, which enables robust numerical integrations. The system of species transport equations is transformed to reaction-extent transport equations, …

Developing A Gis And Hydrological Modeling Approach For Sustainable Water Resources Management In The West Bank -- Palestine, Walid Wajeeh Sabbah

Theses and Dissertations

This research deals with setting up a GIS and hydrological modeling based approach for sustainable water resources management in the West Bank of Palestine. This water sustainability approach took into consideration the water balance, the social, the economic, the demographic, the environmental, and the institutional components in order to enhance and promote the sustainable development in Palestine, both on the short and long runs. To evaluate the water balance component, a methodology was introduced to create the Water Sustainability Map (WSM). Since the groundwater is currently the only accessible water source by the Palestinians, the WSM is represented by the …

A New Paradigm Of Modeling Watershed Water Quality, Fan Zhang

Electronic Theses and Dissertations

Accurate models to reliably predict sediment and chemical transport in watershed water systems enhance the ability of environmental scientists, engineers and decision makers to analyze the impact of contamination problems and to evaluate the efficacy of alternative remediation techniques and management strategies prior to incurring expense in the field. This dissertation presents the conceptual and mathematical development of a general numerical model simulating (1) sediment and reactive chemical transport in river/stream networks of watershed systems; (2) sediment and reactive chemical transport in overland shallow water of watershed systems; and (3) reactive chemical transport in three-dimensional subsurface systems. Through the decomposition …

Modeling The Fate And Transport Of Chlorinated Benzenes In Baton Rouge Bayou, Sudheer Nimmagadda

LSU Master's Theses

Knowledge of the fate and transport of chlorinated benzenes is necessary at certain sites for effective remediation of contaminated soils using plants. Current research is examining the capability of wetland plants to catalyze degradation or attenuate migration, but again requires knowledge of the uptake of contaminants from an aqueous environment. A two stage model was used to estimate the rate of uptake of contaminants from sediments. The first stage of the model predicts pollutant leaching rates from sediments to the overlying water, which would then be fed into the plant or bioreactor model systems. In this study the flux from …

Implications Of On-Ground Nitrogen Loading And Soil Transformations On Ground Water Quality Management, M. Almasri, Jagath J. Kaluarachchi

Civil and Environmental Engineering Faculty Publications

This paper presents a modeling approach based on a geographic information system (GIS) to estimate the variability of on-ground nitrogen loading and the corresponding nitrate leaching to ground water. The methodology integrates all point and nonpoint sources of nitrogen, the national land cover database, soil nitrogen transformations, and the uncertainty of key soil and land use-related parameters to predict the nitrate mass leaching to ground water. The analysis considered 21 different land use classes with information derived from nitrogen sources such as fertilizer and dairy manure applications, dairy lagoons, septic systems, and dry and wet depositions. Simulations were performed at …

The Use Of A Water Quality Model To Evaluate The Impacts Of Combined Sewer Overflows On The Lower Hudson River, Wen-Pin Shu

Dissertations

CSO discharges have long been recognized as a significant source of water pollution. While many sources of water pollution have been controlled over the past 20 years, CSOs continue to be a main environmental concern in several areas, especially in old cities. In the past, most CSO research focused on the CSO control processes, including floatables and suspended solids removal. Few studies have been conducted in the area of the impacts of CSO discharge on the receiving water quality. To achieve this purpose, a powerful water-modeling tool, WASP 6.1, is utilized in this study. The Lower Hudson River is selected …

Nitrification Investigation And Modeling In The Chloraminated Drinking Water Distribution System, Suibing Liu

Electronic Theses and Dissertations

This dissertation consists of five papers concerning nitrification in chloraminated drinking water distribution systems in a one and a half year field study. Seven finished waters were produced from different treatment processes and distributed to eighteen pilot distribution systems (PDSs) that were made pipes taken from actual distribution systems. Unlined cast iron (UCI), galvanized steel (G), lined cast iron (LCI), and PVC pipes were used to build the PDSs. All finished waters were stabilized and chloraminated before entering the PDSs. This dissertation consists of five major parts. (1) System variations of nitrates, nitrites, DO, pH, alkalinity, temperature, chloramine residuals and …