Civil and Environmental Engineering Commons^™

Implementation Of A Non-Metallic Reinforced Bridge Deck, Volume 2: Thayer Road Bridge, Robert J. Frosch, Ali Cihan Pay

JTRP Technical Reports

The primary maintenance problem with bridges in Indiana has been deterioration of the concrete deck which is often related to corrosion of the reinforcing steel. While a corrosion protection system consisting of epoxy-coated reinforcement in combination with 2-1/2 in. of Class C concrete cover has been used in Indiana, research and experience have demonstrated that this system can be compromised. As an alternative solution to the corrosion problem in reinforced concrete, fiber reinforced polymer (FRP) bars which are corrosion resistant can be provided as reinforcement. This research was divided into two phases directed towards the implementation of a nonmetallic reinforced …

Characterization Of Recycled Concrete For Use As Pavement Base Material, Brandon J. Blankenagel

Theses and Dissertations

The use of recycled concrete material (RCM) as pavement base material is a promising but unproven technique for road rehabilitation and construction. A telephone survey conducted to investigate the state of the practice concerning RCM usage in Utah County revealed that RCM is infrequently used in this application due primarily to a lack of practical knowledge about the engineering properties of the material. Therefore, this research was aimed at evaluating the physical properties, strength parameters, and durability characteristics of both demolition and haul-back sources of RCM available in Utah County for use as pavement base material. The study included extensive …

Interaction Between Micro-Cracking, Cracking, And Reduced Durability Of Concrete: Developing Methods For Considering Cumulative Damage In Life-Cycle Modeling, Zhifu Yang, W. Jason Weiss, J. Olek

JTRP Technical Reports

It is becoming increasingly popular to utilize numerical simulation models to predict the long-term performance of concrete pavements and structures. The majority of these models have been developed using laboratory test data that considers concrete in an uncracked state. While uncracked concrete exists as the best case scenario, frequent cracking occurs in real structures that could have a profound impact on life cycle performance. Cracks from several sources may accumulate and interact thereby accelerating the deterioration of concrete. For example, the distributed cracking caused by freeze/thaw damage can substantially increases the rate of water absorption and reduces the load carrying …

An Investigation On Transversely Prestressed Concrete Bridge Decks, J. A. Ramirez, Jhon Paul Smith

JTRP Technical Reports

This study is concerned with the development of design specifications for the use of transverse post-tensioning in concrete bridge decks. The ultimate goal behind this proposal is to improve the durability of concrete bridge superstructures. Experimental results from previous studies are used to validate the analytical models implemented in the development of the design specifications. It is found that the required distribution of transverse post-tensioning is such that different application levels of prestressing are required in regions containing the interior and exterior (or outermost) diaphragms. It is also concluded that the magnitude of such transverse forces is a function of …

Effects Of Carbonation On Mechanical Properties And Durability Of Concrete Using Accelerated Testing Method, Jack M. Chi, Ran Huang, C. C. Yang

Journal of Marine Science and Technology–Taiwan

An experimental investigation was carried out to study the effect of carbonation on mechanical properties and durability of concrete. Ordinary portland concretes (OPC) with water/cement ratios of 0.58 and 0.48 and self-compacting concretes (SCC) with water/binder ratios of 0.40 and 0.36 were used in this study. Compressive strength test, splitting strength test, electrical resistivity test, rapid chloride penetration test (RCPT), open circuit potential method and alternative current (AC) impedance method were performed to estimate the properties of concrete. Test results showed that carbonation may compensate some concrete properties such as compressive strength, splitting strength, electrical resistivity and chloride ion penetration. …

Design Of Durable Concrete Railroad Crossings, Anthony J. Lamanna, Charles F. Scholer

JTRP Technical Reports

Existing precast concrete railroad crossings in the state of Indiana are experiencing too short a life expectancy. This study proposes methods that can be used to produce durable concrete railroad crossings with satisfactory rideability, durability, and longevity. Thirty-two precast concrete railroad crossings were visited in central and northern Indiana. Failures were determined to belong to three major categories: structural capacity causes, environmental causes, and material property causes. A concrete mix was evaluated at three different polyolefin fiber contents and without fibers. Beams were tested in flexure, and modulus of rupture and first crack deflection were recorded for each beam. Cylinders …

Performance-Related Specifications For Concrete Bridge Superstructures, Volume 4: Bond Of Epoxy-Coated Bars With Thicker Coatings, J. A. Ramirez, Michael K. Appelhans

JTRP Technical Reports

In Volume 4 of the final report, the results of an evaluation of the bond performance of epoxy-coated bars with a coating thickness up to 18 mils are presented. The experimental work on the bond performance of epoxy-coated bars with thickness up to 18 mils indicates that the current AASHTO requirements for development length of epoxy-coated bars up to #8 could be safely extended to coating thickness of up to 18 mils. Thus, no change to the bond specifications is recommended in order to implement the use of bars with diameters up to a #8 with epoxy-coating thickness up to …

Performance-Related Specifications For Concrete Bridge Superstructures, Volume 3: Nonmetallic Reinforcement, Robert J. Frosch, Christopher P. Mosley, Ahmet Koray Tureyen

JTRP Technical Reports

In Volume 3 of the final report, research work conducted to investigate the behavior of fiber reinforced polymer (FRP) reinforcement is summarized. This study focused on the behavior of FRP reinforced concrete structures with an emphasis on bond and shear. For the bond investigation, three series of beam splice tests were performed on specimens reinforced with steel, glass FRP, and aramid FRP to determine the effect of the different types of reinforcement on bond, cracking, and deflections. The test results indicate that the use of FRP reinforcement leads to lower bond strengths and, therefore, require longer development lengths. The specimen …

Performance-Related Specifications For Concrete Bridge Superstructures, Volume 1: Performance Parameters And Related Procedure For Concrete Bridge Superstructures, J. A. Ramirez, Jhon Paul Smith

JTRP Technical Reports

In Volume 1 of the final report, the identification of performance levels and parameters, and the development of acceptance criteria, have been addressed. Emphasis has been placed on the development of a methodology for a Performance Related Specification, PRS, for concrete bridge superstructures. The implementation of the methodology, presented in the form of a user-friendly computer program, is project specific. It requires the mean and standard deviation (or definition of a probability distribution) of the input parameters for the performance predictive models. This is done for both the as-designed condition and the as-built condition of the structure. The contractor is …

Development And Evaluation Of Cement-Based Materials For Repair Of Corrosion-Damaged Reinforced Concrete Slabs, Rongtang Liu, J. Olek

JTRP Technical Reports

In this study, the results of an extensive laboratory investigation conducted to evaluate the properties of concrete mixes used as patching materials to repair reinforced concrete slabs damaged by corrosion are reported. Seven special concrete mixes containing various combinations of chemical or mineral admixtures were developed and used as a patching material to improve the durability of the repaired slabs. Physical and mechanical properties of these mixes, such as compressive strength, static modulus of elasticity, dynamic modulus of elasticity, and shrinkage were evaluated. Durability-related parameters investigated included resistance of concrete to penetration of chloride ions and freeze-thaw resistance. The results …

Performance Of Bridge Decks And Girders With Lightweight Aggregate Concrete, V. 2 Of 2, J. A. Ramirez, J. Olek, Eric Joseph Rolle, Brian Joseph Malone

JTRP Technical Reports

Structural lightweight concrete is a very versatile material and Haydite and Minergy lightweight aggregates can be utilized in the mixture development of concrete for use in girders and decks in bridges. More widespread use of lightweight aggregates (LWA) would result in savings in construction cost due to considerable dead load reduction.

The materials phase of this research study evaluated the fresh concrete properties (slump, unit weight, and air content), the mechanical properties of hardened concrete (compressive strength, tensile strength, flexural strength, static and dynamic modulus of elasticity, Poisson’s Ratio, and temperature development), and durability related parameters (air void distribution, freeze-that …

Performance Of Bridge Decks And Girders With Lightweight Aggregate Concrete, J. A. Ramirez, J. Olek, Eric Joseph Rolle, Brian J. Manlone

JTRP Technical Reports

Structural lightweight concrete is a very versatile material and Haydite and Minergy lightweight aggregates can be utilized in the mixture development of concrete for use in girders and decks in bridges. More widespread use of lightweight aggregates (LWA) would result in savings in construction cost due to considerable dead load reduction. The materials phase of this research study evaluated the fresh concrete properties (slump, unit weight, and air content), the mechanical properties of hardened concrete (compressive strength, tensile strength, flexural strength, static and dynamic modulus of elasticity, Poisson’s Ratio, and temperature development), and durability related parameters (air void distribution, freeze-thaw …

Concrete Cracking In Coastal Areas, S. R. Mpinzire

Tanzania Journal of Engineering and Technology (TJET)

The paper discusses cracking and corrosion of reinforced concrete (RC) structures in coastal zones where aggressive action of salt burdened air is the primary cause of concrete deterioration. Case studies are presented, along with discussion of possible remedies including local demolition, reconstruction and epoxy injection as well as concrete treatment.

Methods Of Corrosion Protection And Durability Of Concrete Bridge Decks Reinforced With Epoxy-Coated Bars - Phase I, Lisa Michele Samples, J. A. Ramirez

JTRP Technical Reports

In this study, the results of an extensive field and laboratory investigation conducted to evaluate the corrosion performance of epoxy-coated reinforcement are reported. One hundred and twenty three concrete bridge decks containing epoxy-coated reinforcement, uncoated reinforcement, and various other corrosion protection systems were included in a field investigation. An initial visual inspection of these bridge decks showed that 44% had signs of distress from corrosion of the reinforcement. Six decks, representing 5% of the total sample, were selected for a second more detailed survey. Three of the six decks had epoxy-coated reinforcement. This number represents 11% of the total sample …

The Short-Term Effects Of Mortars On Salt Movement In Stone, Simon H. Perry, Aidan Duffy

Articles

Salt-induced decay processes are one of the most important reasons for the decay of many stone buildings and monuments. This paper investigates the role played by masonry mortars in the movement of salts within Baumberger sandstone and Portland limestone. The methodology used involved the monitoring of stone units containing mortar joints which were exposed to a city-centre environment. Rain-water run-off was collected from the stone/mortar units during the exposure period; the units were subsequently destructively analysed. The methods of run-off and destructive sample analysis used included ion chromatography and atomic absorption spectrophotometry; stone and mortar samples were also analysed petrographically. …

Testing Of Multi-Span Bridges With Full Span Precast Prestressed Concrete Panels (Phase 1), Robert J. Peterman, J. A. Ramirez

JTRP Technical Reports

The purpose of this study was to assess the behavior and durability of multi-span bridges constructed with full-span prestressed concrete form panels. The use of full-span prestressed concrete form panels for bridges with spans of 40 ft. or less is an economical method of construction due to the reduction of on-site formwork and labor required by alternate cast-in-place systems. In this research, a pair of two-span bridges utilizing full-span prestressed concrete form panels were fabricated and tested in the Karl H. Kettelhut Structural Engineering Laboratory at Purdue University. Time-dependent effects were monitored during the cast-in-place (CIP) concrete cure period of …

Effects Of Accelerated Weathering On Architectural Laminated Glass In A Windstorm Environment, Richard A. Behr, Joseph E. Minor, Paul A. Kremer

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

An experimental study was conducted to assess the serviceability and ultimate limit state behavior of a fully glazed architectural laminated glass system under accelerated weathering conditions. Glazed specimens included heat-strengthened laminated glass with a low-emissivity, metallic solar coating on one glass surface next to the polyvinyl butyral interlayer. The laminated glass units were anchored to the aluminum curtain wall frame with a perimeter anchor bead of medium-modulus structural silicone sealant. Accelerated weathering was performed in a manner similar to the provisions of ASTM E773-88 and E774-92. All specimens (weathered and unweathered) were then subjected to a severe windstorm simulation test, …

Evaluation Of Diamond Grade Reflective Sheeting, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of this project was to monitor the performance of the diamond grade sheeting when used on both typical traffic signs and construction signs. The durability, appearance, and reflectivity of the signs were monitored. Diamond grade sheetings used on typical traffic signs were evaluated over a two-year period with construction signs evaluated over an 18-month period.

Diamond grade sheeting was found to provide increased reflectivity compared to high intensity sheeting with no problems noted related to durability or appearance. However, the cost of the diamond grade sheeting would limit its use to situations where brighter, wider-angle reflective sheeting is …

Repointing Mortars For Conservation Of A Historic Stone Building In Trinity College, Dublin, Aidan Duffy, Tim P. Cooper, Simon H. Perry

Articles

With atmospheric pollution causing building stone to decay at accelerated rates, conservation of historic stone monuments is becoming an increasingly important issue. Mortar joints have a marked effect on how moisture moves in a wall and, hence, on how the wall weathers. Not only does mortar bind stones together, but also a good mortar will prevent the ingress of moisture (and pollutants), enable the buildings to dry out, accommodate movement and will not act as a source of harmful chemicals capable of attacking the surrounding stone. Thus, poor mortar can have deleterious effects on the stonework. This paper, which is …

Evaluation Of Stamark Brand Bisymmetric 1.75 Grade Pavement Marking Tape, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of this project was to evaluate the performance of Stamark Brand Bisymmetric 1.75 Grade pavement Marking Tape (Series 320) on a large-scale installation on Interstate 24 in McCracken County. The evaluation consisted of periodic inspection of the tape to determine its durability, appearance, and reflectivity.

The tape has demonstrated good performance after two years in service. No durability problems were noted. While the appearance of the tape was not as bright as a typical traffic paint, it was adequate. The tape has maintained a high level of reflectivity. The performance of the material would potentially warrant additional use …

Evaluation Of Flexible Delineator Posts, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of this study was to install a small number of lightweight metal u-channel posts with a round delineator and a small number of commonly used flexible posts and evaluate their performance. Three types of flexible posts were installed. They included two posts manufactured by Carsonite and one manufactured by Safe-Hit.

The results of the limited field tests does not support widespread use of flexible posts. Substantial durability problems were encountered with the flexible posts. Future use of flexible posts should be limited to potential high-hit areas such as gores at urban interchanges. While the durability of the metal …

Long-Term Evaluation Of Durable Lane Delineation Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of this report was to summarize the long-term performance of several types of durable lane delineation materials. Polyester paint was determined to be an effective durable lane material with most use of this material being on asphaltic concrete surfaces having an average daily traffic of under 10,000. Extruded thermoplastic was also determined to be an effective durable lane delineation material with its cost limiting its use to higher volume asphaltic concrete surfaces. Either the hydrocarbon or alkyd thermoplastic formulation could be used but the alkyd formulation was observed to maintain a higher reflectivity. While not classified as a …

Evaluation Of Construction-Zone Pavement Marking Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objectives of this study were to evaluate available foil-back and removable tapes as well as one new construction-zone raised pavement marker and to recommend materials that should be included on approved lists for use by the Kentucky Department of Highways. Tapes were placed on transverse test sections and the reflectivity, durability, and appearance were observed.

Tapes to be included on the approved lists for foil-back and removable tapes were recommended. Tapes manufactured by 3M, Flex-0-Lite, and Swarolite were included on the list of acceptable foil-back tapes. Recommended removable tapes were the 3M and Cataphote removable tapes. The Astra Optics …

Evaluation Of Extruded Thermoplastics As Lane Delineation, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

This study involved an evaluation of large-scale installations of both hydrocarbon and alkyd extruded thermoplastics as lane delineation on sections of interstate highways having open-graded surfaces. The objective of the study was to evaluate the performance of thermoplastics as lane delineation and to compare the performance of hydrocarbon versus alkyd formulations.

Data were collected on a periodic basis over an 18-month period. Data collection consisted of daytime observations of the appearance and durability of the thermoplastic material along with reflectivity measurements using a portable retroreflectometer.

The evaluation revealed that both the hydrocarbon and alkyd extruded thermoplastic material maintained their appearance, …

Evaluation Of Procedures For Testing Aggregates, David Q. Hunsucker

Kentucky Transportation Center Research Report

This report summarizes findings of a research study conducted to evaluate aggregate testing procedures as related to aggregate soundness and durability. The objectives of the study were to determine a suitable replacement or modification of Kentucky's existing Sodium Sulfate Soundness Test for aggregates which would more accurately reflect in-service performance of concrete pavements and bridges, to correlate freezing and thawing durability data and other test data with sodium sulfate soundness data, and to develop a rational implementation criterion for use of new or modified testing procedures.

There were no observable correlations between the various test methods evaluated and the Sodium …

A Survey Of States' Aggregate Soundness Specifications And Test Methods, David Q. Hunsucker

Kentucky Transportation Center Research Report

This report summarizes findings of a national survey to determine aggregate durability test methods and specification requirements of the various states. Also included are specifications and test methods concerning allowable shale contents in aggregates and requirements for percentages of crushed particles in aggregates.

Evaluation Of Epoxy Thermoplastic Pavement Marking Material, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of this study was to evaluate the field performance of epoxy thermoplastic (ETP) as a pavement marking material and to compare it to a control marking material, which was alkyd traffic paint. A test installation of ETP along with the regular traffic paint was placed on KY 841 in Jefferson County and evaluated over an 18-month period. Data collection consisted of daytime observations and rating of the material's appearance and durability and nighttime observations and rating of its nighttime visibility. Reflectivity measurements were also collected using a portable retroreflectometer.

The appearance (color) of the ETP remained good over …

Evaluation Of Snowplowable Marker Installations, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The first large-scale contracts for the installation of snowplowable markers were awarded in 1984 and 1985. Stimsonite 96 and recessed markers were installed. The objective of this study was to evaluate the performance of the installations. Durability and reflectivity results show that both the recessed markers and Stimsonite 96 markers have performed effectively as snowplowable markers. The recessed markers should continue to be used only on four-lane highways constructed to high geometric standards with the Stimsonite 96 markers installed on the majority of highways.

Evaluation Of Durable Lane Delineation Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of the study was to evaluate the cost-effectiveness of available marking materials by means of field tests and to make recommendations concerning the optimum lane delineation materials based on these tests. Materials tested include 100-percent solid epoxy paint, polyester paint, extruded thermoplastic, 3M Stamark tape, 3M Bisymmetric tape, EPOFLEX, solvent epoxy paint, chlorinated rubber traffic paint, and alkyd traffic paint. The test installations have been in place up to four years. The evaluation concerned the durability, reflectivity, and appearance of the materials. Based on current data, expanded use is warranted for 1) polyester paint on lower-volume asphaltic concrete …

Evaluation Of Durable Crosswalk And Stopbar Marking Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of this study was to find the most cost-effective durable marking material to provide long-lasting stop bars and crossbars. Three materials were tested: 1) 3M Stamark tape, 2) Prismo preformed tape, and 3) extruded thermoplastic (hydrocarbon and alkyd). The various test installations were in place for between 6 and 30 months.

The alkyd-resin thermoplastic material was found to be the most cost-effective I material. The preformed tapes cost two to three times as much as the thermoplastic material while not providing as durable a material when used in this application.The alkyd-resin material maintained its appearance better than the …