Open Access. Powered by Scholars. Published by Universities.®

Civil and Environmental Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2011

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 481 - 510 of 934

Full-Text Articles in Civil and Environmental Engineering

The Formation Design Of Noise Reducers From Plywood, Foam, Tray, Dan Coconut Fiber For Static Sources, Melati Ferianita Fachrul, Wisnu Eka Yulyanto, Asharani Merya Apr 2011

The Formation Design Of Noise Reducers From Plywood, Foam, Tray, Dan Coconut Fiber For Static Sources, Melati Ferianita Fachrul, Wisnu Eka Yulyanto, Asharani Merya

Makara Journal of Technology

The Formation Design of Noise Reducers from Plywood, Foam, Tray, dan Coconut Fiber for Static Sources. Research was conducted in a semi-anechoic room using a method referring to the ISO 3745. The design used is the Hemisphere in which the source of noise is analogous to engines in an industry. The value reduction in the rate of sound power is obtained by comparing the sound power level before and after control is given. The noise control test materials used consist of layers of plywood, foam, fiber and tray (egg box). The effectiveness of these materials is tested by measuring the …

Go to article

Performance Of Indiana’S Superpave Hma Mixtures, Ayesha Shah, Rebecca Mcdaniel Apr 2011

Performance Of Indiana’S Superpave Hma Mixtures, Ayesha Shah, Rebecca Mcdaniel

JTRP Technical Reports

This project followed the performance of a number of hot mix asphalt paving projects for seven to eight years in an attempt to relate laboratory test results to field performance. First, a small scale study compared sampling locations, specific gravity test procedures and compaction devices used on two samples from projects, one with volumetric acceptance and one with non-volumetric acceptance, to determine the best combination to use for Part 2 of the study. In Part 2, 12 projects constructed in 2001 and 2002 were sampled, tested and monitored. Laboratory testing involved determining maximum and bulk specific gravities, binder content, air …

Go to article

Instrumentation Of Buildings To Enhance Student Learning - A Case Study At Marquette University's Discovery Learning Compex, Meredith Claeys Apr 2011

Instrumentation Of Buildings To Enhance Student Learning - A Case Study At Marquette University's Discovery Learning Compex, Meredith Claeys

Master's Theses (2009 -)

The new engineering building at Marquette University, the Discovery Learning Complex, has been designed to change the way engineering education is delivered by using the building itself as a teaching tool for the next generation of engineers. The structural system for the building has been instrumented to allow students access to structural system data, wind speed data, and foundation pressures enabling this data from the building to be integrated into the teaching environment. The building also will display aspects of the building management system for public viewing. An array of weather stations will be installed on the roof, allowing the …

Go to article

Comparison Of Aquifer Sustainability Under Groundwater Administrations In Oklahoma And Texas, Aaron R. Mittelstet, Michael D. Smolen, Garey A. Fox, Damian C. Adams Apr 2011

Comparison Of Aquifer Sustainability Under Groundwater Administrations In Oklahoma And Texas, Aaron R. Mittelstet, Michael D. Smolen, Garey A. Fox, Damian C. Adams

Department of Agricultural and Biological Systems Engineering: Faculty Publications

We compared two approaches to administration of groundwater law on a hydrologic model of the North Canadian River, an alluvial aquifer in northwestern Oklahoma. Oklahoma limits pumping rates to retain 50% aquifer saturated thickness after 20 years of groundwater use. The Texas Panhandle Groundwater Conservation District’s (GCD) rules limit pumping to a rate that consumes no more than 50% of saturated thickness in 50 years, with reevaluation and readjustment of permits every 5 years. Using a hydrologic model (MODFLOW), we simulated river-groundwater interaction and aquifer dynamics under increasing levels of ‘‘development’’ (i.e., increasing groundwater withdrawals). Oklahoma’s approach initially would limit …

Go to article

Natural Gas As Petroleum Fuel Substitution: Analysis Of Supply-Demand Projections, Infrastructures, Investments And End-User Prices, Abdul Qoyum Tjandranegara, Arsegianto Arsegianto, Widodo Wahyu Purwanto Apr 2011

Natural Gas As Petroleum Fuel Substitution: Analysis Of Supply-Demand Projections, Infrastructures, Investments And End-User Prices, Abdul Qoyum Tjandranegara, Arsegianto Arsegianto, Widodo Wahyu Purwanto

Makara Journal of Technology

The petroleum fuels (PF) subsidy has long burdens the government spending, and discourages less expensive energy usage such as natural gas (NG). Exporting NG and importing the more expensive PF products cause financial losses to Indonesia. The lack of NG infrastructure is the main hurdle in maximizing domestic NG usage and so does the perception of its high investment costs burdening government spending and pushing the NG transportation cost up. This study calculates the required NG infrastructure and its investments for several levels of PF substitutions up to 2030. To balance the NG demands, the supply from each field and …

Go to article

The Synergy Of Recombinant Xylanolytic Enzyme On Xylan Hydrolysis, One Asmarani, Bambang Prajogo Eko Wardojo, Ni Nyoman Tri Puspaningsih Apr 2011

The Synergy Of Recombinant Xylanolytic Enzyme On Xylan Hydrolysis, One Asmarani, Bambang Prajogo Eko Wardojo, Ni Nyoman Tri Puspaningsih

Makara Journal of Technology

Microbial xylanases or xylanolytic enzyme have received considerable attention over the last years owing to a multitude of possible applications. These enzymes have potential in the biodegradation of lignocellulosic biomass to fuels, chemicals, fruit juice, animal feed and in improving rumen digestion. More recently, the use of xylanases as bleaching agent in the pulp and paper industry has been suggested to replace of some of the chemicals presently used for this purpose. Such applications could have an important positive impact on the environment. The purpose of this research was determining the synergy of 3 recombinant xylanolytic enzymes (β-xylosidase, exo-xylanase and …

Go to article

Cradle To Gate Simple Life Cycle Assessment Of Biodiesel Production In Indonesi, Akhmad Hidayatno, Teuku Yuri M. Zagloel, Widodo Wahyu Purwanto, Carissa Carissa, Lindi Anggraini Apr 2011

Cradle To Gate Simple Life Cycle Assessment Of Biodiesel Production In Indonesi, Akhmad Hidayatno, Teuku Yuri M. Zagloel, Widodo Wahyu Purwanto, Carissa Carissa, Lindi Anggraini

Makara Journal of Technology

The focus of this research is to analyze potential environmental impact in the supply chain of palm oil biodiesel industries. Simple Life Cycle Assessment (LCA) is applied to analyze impacts, produced by the three main units in the supply chain of Palm-Oil-based Biodiesel, which are Palm Plantation, CPO mill, and Biodiesel Plant. We developed LCA calculation model using spreadsheet software, used to assess a number of input scenarios to evaluate the best scenario, in variation of: land quality, land area and the rate of clearing, land clearing technique and type of the original land. The biggest potential environmental impact is …

Go to article

Characterization Of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum Inophyllum Linn), Santiyo Wibowo, Wasrin Syafi, Gustan Pari Apr 2011

Characterization Of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum Inophyllum Linn), Santiyo Wibowo, Wasrin Syafi, Gustan Pari

Makara Journal of Technology

Characterization of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum inophyllum Linn). Chemical and physical activation of nyamplung shell with 0%, 5%, and 10% H3PO4 for 60 and 120 minutes has been carried out to prepare activated charcoal. The purpose of this experiment was to look into the characteristic of nyamplung shell activated charcoal surface. Nyamplung shell was carbonized into charcoal, then activated by immersion in H3PO4 solution using 0%, 5% and 10%, for 24 hours, and heated in retort at two temperatures (700 and 800 oC) and two duration (60 and 120 minutes). The material were characterized by fourier transform …

Go to article

An Investigation Into The Resistance/Powering And Seakeeping Characteristics Of River Catamaran And Trimarana, Murdijanto Murdijanto, I Ketut Aria Pria Utama, Andi Jamaluddin Apr 2011

An Investigation Into The Resistance/Powering And Seakeeping Characteristics Of River Catamaran And Trimarana, Murdijanto Murdijanto, I Ketut Aria Pria Utama, Andi Jamaluddin

Makara Journal of Technology

The increase of fuel price has caused fleet operational and shipping business to be in danger situation. The fuel consumption of a ship is influenced by ship volume or wetted area which contributes directly to the increase of ship resistance and the size of main engine. In order to find out the appropriate answers, a series of investigation into river transportation using monohull, catamaran and trimaran types of vessel was carried out. The work focused on the estimation of total resistance and powering as well as seakeeping characteristics and carried out experimentally using tank test and numerically using a ship …

Go to article

Determining The Standard Value Of The Oily Distortion Of Acquisition The Fingerprint Images, Rahmat Syam, Mochamad Hariadi, Mauridhi Hery Purnomo Apr 2011

Determining The Standard Value Of The Oily Distortion Of Acquisition The Fingerprint Images, Rahmat Syam, Mochamad Hariadi, Mauridhi Hery Purnomo

Makara Journal of Technology

Determining the Standard Value of the Oily Distortion of Acquisition the Fingerprint Images. This research describes a novel procedure for determining the standard value of the oily distortion of acquisition the fingerprint images based on the score of clarity and ridge-valley thickness ratio. The fingerprint image is quantized into blocks size 32 x 32 pixels. Inside each block, an orientation line, which perpendicular to the ridge direction, is computed. The center of the block along the ridge direction, a two-dimension (2-D) vector V1 (slanted square) with the pixel size 32 x 13 pixels can be extracted and transformed to a …

Go to article

Are Ieee 754 32-Bit And 64-Bit Binary Floating-Point Accurate Enough?, Bernaridho Hutabarat, I Ketut Eddy Purnama, Mochamad Hariadi, Mauridhi Hery Purnomo Apr 2011

Are Ieee 754 32-Bit And 64-Bit Binary Floating-Point Accurate Enough?, Bernaridho Hutabarat, I Ketut Eddy Purnama, Mochamad Hariadi, Mauridhi Hery Purnomo

Makara Journal of Technology

This paper describes a research toward the accuracy of floating-point values, and effort to reveal the real accuracy. The methods used in this research paper are assignment of values, assignment of value of arithmetic expressions, and output the values using floating-point value format that helps reveal the accuracy. The programming-tool used are Visual C# 9, Visual C++ 9, Java 5, and Visual BASIC 9. These tools run on top of Intel 80 x 86 hardware. The results show that 1*10-x cannot be accurately represented, and the approximate accuracy ranges only from 7 to 16 decimal digits.

Go to article

Ergonomic Analysis Of Garment Industry Using Posture Evaluation Index (Pei) In Virtual Environment, Erlinda Muslim, Boy Nurtjahyo, Romadhani Ardi Apr 2011

Ergonomic Analysis Of Garment Industry Using Posture Evaluation Index (Pei) In Virtual Environment, Erlinda Muslim, Boy Nurtjahyo, Romadhani Ardi

Makara Journal of Technology

Ergonomic Analysis of Garment Industry using Posture Evaluation Index (PEI) in Virtual Environment. This research tried to study, in a virtual environment, the ergonomics of four divisions in garment industry: cutting division, sewing division, button division, and finishing division. Variables that influence the working conditions in each division are different; depend on the real situations that happened. The purpose is to assess the real working conditions based on ergonomics study using Posture Evaluation Index (PEI). PEI integrates the scores of low back analysis (LBA), ovako working posture (OWAS), and rapid upper limb assessment (RULA). Analysis phase was done using digital …

Go to article

Formation Of Caco3 Particle And Conductivity Of Na2co3 And Cacl2 Solution Under Magnetic Field On Dynamic Fluid System, Nelson Saksono, Setijo Bismo, Roekmijati Widaningroem, Azwar Manaf Apr 2011

Formation Of Caco3 Particle And Conductivity Of Na2co3 And Cacl2 Solution Under Magnetic Field On Dynamic Fluid System, Nelson Saksono, Setijo Bismo, Roekmijati Widaningroem, Azwar Manaf

Makara Journal of Technology

Hard water causes the CaCO3 scale formation on the pipe walls and heat exchanger equipments in industrial or domestic water processes. A great number of experimental researches on the prevention of the CaCO3 precipitation process by magnetic field have been carried out. In this research, Na2CO3 and CaCl2 solutions was magnetized in the circulated flow condition (dynamic fluid system). The velocity of fluid and the circulation time was modified to examine its influences to the magnetization process. CaCO3 content was measured by titration method of EDTA complexometry. Conductivity test was conducted to find out hydrate ion bonding. The results showed …

Go to article

Two-Class Classification With Various Characteristics Based On Kernel Principal Component Analysis And Support Vector Machines, Ivanna Kristianti Timotius, Iwan Setyawan, Andreas Ardian Febrianto Apr 2011

Two-Class Classification With Various Characteristics Based On Kernel Principal Component Analysis And Support Vector Machines, Ivanna Kristianti Timotius, Iwan Setyawan, Andreas Ardian Febrianto

Makara Journal of Technology

Two class pattern classification problems appeared in many applications. In some applications, the characteristic of the members in a class is dissimilar. This paper proposed a classification system for this problem. The proposed system was developed based on the combination of kernel principal component analysis (KPCA) and support vector machines (SVMs). This system has been implemented in a two class face recognition problem. The average of the classification rate in this face image classification is 82.5%.

Go to article

Addressing Water Quality Issues In Rural Cameroon With Household Biosand Filters, Laine Klopfensten, Laura Petrasky, Valerie Winton, Jeff Brown Apr 2011

Addressing Water Quality Issues In Rural Cameroon With Household Biosand Filters, Laine Klopfensten, Laura Petrasky, Valerie Winton, Jeff Brown

Publications

This paper describes an ongoing collaboration between the Hope College student chapter of Engineers Without Borders – USA and the rural community of Nkuv in the Northwest Province of Cameroon related to improving drinking water quality using Manz biosand filters. The collaboration began in 2006 and focused on developing a community-based construction and distribution model for household water treatment units. Results from microbiology testing of the constructed filters indicate that this water treatment method is effective for improving water quality in rural areas. The results also highlight the need for ongoing assessment and adapting community education programs to provide necessary …

Go to article

Solving The Vehicle Re-Identification Problem By Using Neural Networks, Tanweer Rashid Apr 2011

Solving The Vehicle Re-Identification Problem By Using Neural Networks, Tanweer Rashid

Computational Modeling & Simulation Engineering Theses & Dissertations

Vehicle re-identification is the process by which vehicle attributes measured at one point on a road network are compared to vehicle attributes measured at another point in an effort to match vehicles without using any unique identifiers such as license plate numbers. A match is made if the two measurements are estimated to belong to the same vehicle. Vehicle attributes can be sensor readings such as loop induction signatures, or they can also be actual vehicle characteristics such as length, weight, number of axles, etc. This research makes use of vehicle length, travel time, axle spacing and axle weights for …

Go to article

A Study Of The Correlation Of Sub-Aqueous Beach Profile Change And The Coastal Storm Impulse (Cosi) Parameter, Kevin Bryan Conner Apr 2011

A Study Of The Correlation Of Sub-Aqueous Beach Profile Change And The Coastal Storm Impulse (Cosi) Parameter, Kevin Bryan Conner

Civil & Environmental Engineering Theses & Dissertations

The Coastal Storm Impulse (COSI) parameter is a recently developed storm-strength parameter that was first introduced at the San Diego, California International Conference of Coastal Engineering in 2006 (ICCE) and further examined in 2008 at the ICCE in Hamburg, Germany. This new parameter used the principles of conservation of horizontal momentum to combine storm characteristics such as surge, wave dynamics, currents, and duration into a relative scale used to classify and measure storm response and impacts. The resultant classification system was intended to evaluate potential coastal erosion and the associated loss of coastal infrastructure, as well as provide a storm …

Go to article

Assessment Of State Composting Regulations In The United States, Nazli Yesiller, Samuel A. Vigil, James L. Hanson Mar 2011

Assessment Of State Composting Regulations In The United States, Nazli Yesiller, Samuel A. Vigil, James L. Hanson

Civil and Environmental Engineering

This investigation was conducted to identify the current "status of state composting regulations in the U.S. using an extensive survey administered to regulators from all 50 states. Questions were included regarding: background information on composting: status of regulations: regulatory details including feedstock specific provisions and regulatory framework with respect to MSW regulations: details regarding type, properties, and amount of materials handled by composting activities; outgoing materials and storage of materials; type of composting facilities: initial development of the regulations; level of rigor of regulations: enforcement and reporting requirements; efficiency and level of satisfaction with regulations: permitting fees; and modifications to …

Go to article

Green Building Policy And School Performance, S. Kelting, M. Montoya Mar 2011

Green Building Policy And School Performance, S. Kelting, M. Montoya

Construction Management

The movement to construct high performance “green” buildings has had unprecedented market growth and continues to become a mainstream practice for constructing schools in the United States. This paper will consider how the results of government requirements for higher performance school buildings may affect the health and performance of students. The research focuses on educational leaders’ perceptions of how they would prioritize green building strategies based on recent governmental policy that requires building green schools. There is clear and compelling evidence that schools currently built to specific green standards of indoor environmental quality, specifically lighting, result in healthier and more …

Go to article

Evaluation Of Portable Devices For Monitoring Microcracking Of Cement-Treated Base Layers, Charles A. Hope Mar 2011

Evaluation Of Portable Devices For Monitoring Microcracking Of Cement-Treated Base Layers, Charles A. Hope

Theses and Dissertations

A relatively new method used to reduce the amount of cement-treated base (CTB) shrinkage cracking is microcracking of the CTB shortly after construction. Three portable instruments used in this study for monitoring the microcracking process include the heavy Clegg impact soil tester (CIST), portable falling-weight deflectometer (PFWD), and soil stiffness gauge (SSG). The specific objectives of this research were 1) to evaluate the sensitivity of each of the three portable instruments to microcracking, and 2) to compare measurements of CTB stiffness reduction obtained using the three devices. The test locations included in this study were Redwood Drive and Dale Avenue …

Go to article

Calibration Of The Highway Safety Manual Safety Performance Function And Development Of Jurisdiction-Specific Models For Rural Two-Lane Two-Way Roads In Utah, Bradford Keith Brimley Mar 2011

Calibration Of The Highway Safety Manual Safety Performance Function And Development Of Jurisdiction-Specific Models For Rural Two-Lane Two-Way Roads In Utah, Bradford Keith Brimley

Theses and Dissertations

This thesis documents the results of the calibration of the Highway Safety Manual (HSM) safety performance function (SPF) for rural two-lane two-way roadway segments in Utah and the development of new SPFs using negative binomial and hierarchical Bayesian modeling techniques. SPFs estimate the safety of a roadway entity, such as a segment or intersection, in terms of number of crashes. The new SPFs were developed for comparison to the calibrated HSM SPF. This research was performed for the Utah Department of Transportation (UDOT).The study area was the state of Utah. Crash data from 2005-2007 on 157 selected study segments provided …

Go to article

Strength And Deformation Characteristics Of A Cement-Treated Reclaimed Pavement With A Chip Seal, Bryan T. Wilson Mar 2011

Strength And Deformation Characteristics Of A Cement-Treated Reclaimed Pavement With A Chip Seal, Bryan T. Wilson

Theses and Dissertations

The objective of this research was to analyze the strength and deformation characteristics of a cement-treated base (CTB) constructed using full-depth reclamation, microcracked, and then surfaced with a single chip seal. In this field study, strength characteristics of the CTB layer were determined at the time of construction, and then both strength and deformation characteristics were evaluated after 9 months of low-volume, heavy truck traffic. After 9 months, observed distresses included transverse cracking, rutting, and chip seal joint failure. The loss of the chip seal was caused by poor chip seal construction practices and not a deficiency in the CTB …

Go to article

Automatic All-Hex Topology Operations Using Edge Valence Prediction With Application To Localized Coarsening, Timothy Ira Miller Mar 2011

Automatic All-Hex Topology Operations Using Edge Valence Prediction With Application To Localized Coarsening, Timothy Ira Miller

Theses and Dissertations

In this work, we propose using edge valence as a quality predictor when used as a driver for adapting all hexahedral meshes. Edge valence, for hexahedra, is defined as the number of faces attached to an edge. It has shown to be a more reliable quality predictor than node valence for hexahedral meshes. An edge valence of 3, 4, or 5 within the volume of a hexahedral mesh has provided at least a positive scaled Jacobian for all observed meshes, without the presence of over constraining geometry. It is often desirable to adapt an existing mesh through sheet operations such …

Go to article

Analysis Of Selected Factors Affecting Concrete Cover Measurements On Bridge Decks, Jeffrey Ryan Hoki Mar 2011

Analysis Of Selected Factors Affecting Concrete Cover Measurements On Bridge Decks, Jeffrey Ryan Hoki

Theses and Dissertations

The objective of this research was to quantify the effects of selected parameters on the accuracy of concrete cover measurements on bridge decks. This research involved three full-factorial laboratory experiments each designed to investigate one of three primary variables. These primary variables included distance to a parallel adjacent bar, distance to a reinforcement intersection, and incorrect bar size input for the cover meter. Each experiment also involved four secondary variables known to affect cover readings. These secondary variables included actual cover depth, meter brand, antenna type, and bar size. Statistical analyses were performed to determine the significance of each factor. …

Go to article

Temporal And Spatial Variability In Base Materials Treated With Asphalt Emulsion, Tyler James Quick Mar 2011

Temporal And Spatial Variability In Base Materials Treated With Asphalt Emulsion, Tyler James Quick

Theses and Dissertations

The first objective of this research was to investigate temporal trends in the mechanical properties of base materials stabilized with asphalt emulsion and to assess the rate at which emulsion-treated base (ETB) design properties are achieved. The second objective of this research was to identify construction and environmental factors most correlated to specific mechanical properties of ETB layers and to determine which construction factors exhibit the greatest variability. Additional statistical analysis was performed to determine if significant differences existed between different test sections on a given project. In this research, three experimental sections were established along a pavement reconstruction project …

Go to article

A Gis-Based Data Model And Tools For Analysis And Visualization Of Levee Breaching Using The Gssha Model, Hoang Luu Tran Mar 2011

A Gis-Based Data Model And Tools For Analysis And Visualization Of Levee Breaching Using The Gssha Model, Hoang Luu Tran

Theses and Dissertations

Levee breaching is the most frequent and dangerous form of levee failure. A levee breach occurs when floodwater breaks through part of the levee creating an opening for water to flood the protected area. According to National Committee on Levee Safety (NCLS), a reasonable upper limit for damage resulting from levee breaching is around $10 billion per year during 1998 and 2007. This number excludes hurricanes Katrina and Rita in 2005 which resulted in economic damages estimated to be more than $200 billion dollar and a loss of more than 1800 lives. In response to these catastrophic failures, the U.S. …

Go to article

A Study Of The Cause Of Failure Of Rotationally Molded, High-Density Polyethylene, Sodium Hypochlorite Storage Tanks, Dixon Harold Abell Mar 2011

A Study Of The Cause Of Failure Of Rotationally Molded, High-Density Polyethylene, Sodium Hypochlorite Storage Tanks, Dixon Harold Abell

Theses and Dissertations

The topic of chemical oxidative degradation in rotational molded polyethylene (high-density cross-linked) chemical (sodium hypochlorite) storage tanks is an industry problem that ranks at the top of current business issues for manufacturers of chemical storage tanks. The degradation of these tanks not only compromises the physical and mechanical properties of the tank material, but reduces the life expectancy of the tank, eventually resulting in catastrophic tank failure. Premature tank failure comes at a hefty cost. The reputation of the manufacturer is questioned often resulting in immediate loss of customer satisfaction and future business. The leaking of the chemical from the …

Go to article

Developing Methods To Assess The Potential Effects Of Global Climate Change On Deer Creek Reservoir Using Water Quality Modeling, Reed Earl Chilton Mar 2011

Developing Methods To Assess The Potential Effects Of Global Climate Change On Deer Creek Reservoir Using Water Quality Modeling, Reed Earl Chilton

Theses and Dissertations

To evaluate the potential impacts of future climate change on a temperate reservoir, I used a calibrated water quality and hydrodynamic model validated using three years of data (2007-2009) from Deer Creek Reservoir (Utah). I evaluated the changes due to altered air temperatures, inflow rates, and nutrient loads that might occur under Global Climate Change (GCC). I developed methods to study GCC on reservoirs. I produced Average Water Temperature Plots, Stratification Plots, and Total Concentration Plots. Average Water Temperature Plots show the sensitivity of the water temperature to various parameters. Stratification Plots quantify stratification length and strength as well as …

Go to article

Automated Delay Estimation At Signalized Intersections: Phase I Concept And Algorithm Development, Taylor R. Forbush Mar 2011

Automated Delay Estimation At Signalized Intersections: Phase I Concept And Algorithm Development, Taylor R. Forbush

Theses and Dissertations

Currently there are several methods to measure the performance of surface streets, but their capabilities in dynamically estimating vehicle delay are limited. The objective of this research is to develop a method to automate traffic delay estimation in real-time using existing field traffic data collection technologies. This research has focused on method and algorithm development that can be applied to existing technologies. Two algorithms were developed to run automatically using Microsoft Excel and Visual Basic to calculate traffic delay from data collected from existing vehicle detection. The algorithms were developed using computer modeling software to simulate different lane configurations. The …

Go to article

Culvert Roughness Elements For Native Utah Fish Passage: Phase I, Lindsay D. Esplin Mar 2011

Culvert Roughness Elements For Native Utah Fish Passage: Phase I, Lindsay D. Esplin

Theses and Dissertations

Culverts can increase stream velocities as a result of reduced waterway areas and prevent upstream passage of small non-salmonid fish such as the Native Utah Leatherside chub (Gila copei) and Longnose dace (Rhinichthyscataractae). To mitigate this problem, current culvert design standards for fish passage match sustained fish swim speeds with average cross sectional velocity through the culvert. Such policies dictate relatively large barrels and do not recognize the role of reduced velocity zones near culvert boundaries. Obstacles and streambed substrate create turbulent regions with lower velocity zones that can increase upstream fish passage. A comparison of …

Go to article

First Prev Next Last