Civil and Environmental Engineering Commons^™

Component Stiffness Method To Predict Lateral Restraint Forces In End Restraint Single Span Z-Section Supported Roof Systems With One Flange Attached To Sheathing, Michael W. Seek, Thomas M. Murphy Oct 2006

Web Crippling Of Sigma-Shaped Metal Studs In A Wall Assembly, E. A. Sumner Oct 2006

Single Bolted Tension Member Design - A New Approach, D. M. Fox, R. M. Schuster Oct 2006

Investigation Of The Shear Stiffness Of Profiled Steel Sheeting Diaphragms With Only Two Edges Fastened, M. Duerr, H. Saal Oct 2006

An Update On Cold-Formed Steel Framing Standards Development In The United States, Jay W. Larson Oct 2006

Mechanical Properties Of Cold-Formed Steel At Elevated Temperatures, Ju Chen, Ben Young Oct 2006

Report On The Development Of A Cold-Formed Steel Design Course At Kansas State University, V. J. Kircher, Sutton F. Stephens Oct 2006

Software Development For Cold-Formed Steel Elements, Francisco Javier Granados Nino, William Gustavo Reyes Ortiz Oct 2006

Cold-Formed Steel Slip-Track Connection, James R. Gerloff, Peter Huttelmaier, Patrick W. Ford Oct 2006

Design Of Distance Profiles In Walls, N. Albrecht, H. Saal, R. Podleschny Oct 2006

Experimental Capacity Assessment Of Cold-Formed Boxed Stud Wall Systems Used In Australian Residential Construction, Maria Pham, Julie Mills, Yan Zhuge Oct 2006

Performance Of Deep Leg L-Headers, Reynaud Serrette, Khanh Chau, Dean Peyton, Bud Waters Oct 2006

Design Of Cold-Formed Web Members With Non-Uniform Cross Sections, Serge Parent, Joseph J. Pote, Kenneth W. Neale Oct 2006

Aisi Standards For Cold-Formed Steel Framing, Jay W. Larson Oct 2006

The Strength Of Cfs Floor Assemblies With Clip Angle Bearing Stiffeners, S. R. Fox Oct 2006

Post-Buckling In The Distortional Mode And Buckling Mode Interaction Of Cold-Formed Thin-Walled Sections With Edge Stiffeners, Derrick C. Y. Yap, Gregory J. Hancock Oct 2006

Buckling Analysis Of Cold-Formed Steel Members Using Cufsm: Conventional And Constrained Finite Strip Methods, S. Adany Oct 2006

Vibration Characteristics And Acceptability Of Cold-Formed Steel Joists, Y. Frank Chen Oct 2006

Designing Cold-Formed Steel Using The Direct Strength Method, Benjamin W. Schafer Oct 2006

Design Criteria For Seam And Sheeting-To-Framing Connections Of Cold-Formed Steel Shear Panels, Lodovic A. Fulop, Daniel Dubina Oct 2006

Cold-Formed Steel Angles Under Axial Compression, Y. Shifferaw, Maximiliano Malite, Benjamin W. Schafer, Gustavo M. B. Chodraui Oct 2006

Local Connection Failures In Composite Sandwich Panel Systems, Andrew Smith, Bret Kershaw, Mahen Mahendran, Somadasa Wanniarachchci Oct 2006

Computer Modeling Of Sloped Z-Purlin Supported Roof Systems To Predict Lateral Restraint Force Requirements, Michael W. Seek, Thomas M. Murray Oct 2006

The Structural Behavior Of Connections Of Cold-Formed Steel Portal Frames, Young Bong Kwon, Hyun Suk Chung, Gap Deuk Kim Oct 2006

Influence Of Profile Distortion On The Shear Flexibility Of Profiled Steel Sheeting Diaphragms, M. Duerr, H. Saal Oct 2006

Effective Width Method Based Design For Distortional Buckling Of Cold-Formed Steel Beams, Cheng Yu, Trevor Lokie Oct 2006

Seismic Performance Of Sheathed Cold-Formed Shear Walls, Raffaele Landolfo, Luigi Fiorino, Gaetano Della Corte Oct 2006

Compression Behavior Of Thin Gusset Plates, Roger A. Laboube, Daniel George Lutz Oct 2006

Finite Element Analysis Of Web Crippling Behaviour Of Cold-Formed Steel Flexural Members, M. Macdonald, J. Rhodes, Manoj A. Heiyantuduwa Oct 2006

A New Ultra Long-Spanning, Combined Steel Formwork And Reinforcement Hybrid Decking System Using Cold-Formed Components, Mathias Glasle, Mark Patrick, Ross Grey Oct 2006