Civil and Environmental Engineering Commons^™

Salt Transport To Saturated Porous Media Under Unstable Conditions: Experimental, Analytical, And Numerical Studies, Kamal Mamoua

Theses and Dissertations

There are three main transport mechanisms that occur under unstable flow conditions: a) The transport of saltwater from the overlying salt source to the underlying porous media, b) the transport of an equivalent volume of displaced groundwater from the porous media into the source, and c) the transport of the saltwater through the porous media. In many situations; such as, estuaries, salt lakes, and landfills, it may be necessary to determine the rate of saltwater transport from an overlying unstable salt source that has heavier saline water overlying porous media fully saturated by lighter saline water. Studies of unstable density …

Use Of Geospatial Technique To Estimate Traffic Volume On South Carolina Roads, Ryan Andrew Devine

Theses and Dissertations

Data from the Federal Highway Administration (FHWA) indicates that there is an increase in the number of vehicles on already congested roadways. For a department of transportation (DOT) to keep up with this increased demand, it is necessary for them to continuously collect and monitor traffic volume on the roads they maintain. One of the most important parameters that DOTs collect and use for traffic engineering and transportation planning studies is annual average daily traffic (AADT). The DOTs are also required to collect and report AADTs to the Federal Highway Administration annually as part of the Highway Performance Monitoring System …

Evaluating The Stabilization Of Gypseous And Gypsiferous Sands Using Different Chemical Additives To Mitigate Gypsum Dissolution, Mohammed Kamil Faris

Theses and Dissertations

Gypsum, which is dihydrate calcium sulfate, (CaSO4.2H2O), is widely available in different sizes, from the size of a rock to the size of a few micrometers as a mineral, in different types of soils. It is primarily found mainly in arid and semi-arid areas around the world at different depths. Soils with gypsum and even gypsum rocks are very hard in their dry state. However, these soils and rock will experience remarkable dissolution upon wetting.

The dissolution phenomenon, which takes place in soils that contain gypsum, creates different geotechnical problems within the soil’s profile, along with foundation issues for structures …

Evaluating The Effectiveness Of The Pedestrian Safety Intervention Program: Behavioral And Observational Approach, Deep Patel

Theses and Dissertations

Pedestrians are considered as the most vulnerable road users. On a nationwide scale, according to the National Highway Traffic Safety Administration, there were 6,075 pedestrian fatalities and more than 85,000 pedestrian injuries as a result of traffic crashes in 2017. This study provides national and state pedestrian fatality statistics, a systematic literature review of pedestrian injury severity, observational (video-based) & behavioral (survey-based) evaluation of the Street-Smart NJ pedestrian safety intervention campaign. Street-Smart NJ is a public education, awareness, and behavioral change campaign program that aims to improve pedestrian safety by increasing awareness of pedestrian safety risks and improving compliance with …

Evaluation Of Impact Of Fiber Type And Dosage Rate On Volumetrics And Laboratory Performance Of Asphalt Mixtures, Ahmad G. M. Alfalah

Theses and Dissertations

The purpose of this study is to evaluate the impact of fiber types, binder content, and dosage rates on the volumetric properties and laboratory performance of asphalt mixtures. One asphalt mixture (control) and four fiber types (Fiberglass, Basalt, Carbon, and Polyolefin/Aramid) were used to evaluate the impact of fiber types and dosage rates. Two mixing procedures for introducing fibers into asphalt mixtures were also evaluated: dry and proportional dispersion methods. To evaluate the impact of fiber types, 0.16% by total mix weight was used. Rutting, cracking, and durability performance tests were evaluated. Furthermore, using 0.15% and 0.3% fiber dosage rates, …

Laboratory Evaluation Of The Impact Of Additives On Asphalt Binders Used In Cold Regions, Neirouz Bouhrira

Theses and Dissertations

The objective of this research study is to evaluate the effect of additives (polymers, nanomaterials, and softening agents) on rutting, cracking, and fatigue performance of asphalt binders commonly used in cold regions (PG 52-34 and PG 64E-40). In this study, the first phase consisted of using polymers (Styrene-Butadiene-Styrene, Ground-Tire-Rubber) and nanomaterials (TiO2 and SiO2) to modify two asphalt binders used in cold regions (PG52-34 and PG64E-40). The second phase of the study consisted of adding a combination of softening agents (Corn oil or Sylvaroad) with polymers (SBR, Epoxy, and SBS) to PG52-34 asphalt binder. The performance evaluation was conducted using …

New Models For Truck Appointment Problem And Extensions, Mohammad Torkjazi

Theses and Dissertations

The problematic issues surrounding gate congestion at marine container terminals have been well documented. Random truck arrivals at maritime container terminals are one of the primary reasons for gate congestion. Gate congestion negatively affects the terminal’s and drayage firms’ productivity and the surrounding communities in terms of air pollution and noise. To alleviate gate congestion, more and more terminals in the U.S. are utilizing a truck appointment system (TAS).

The first study proposes a novel approach for designing a Truck Appointment System (TAS) intended to serve both the marine container terminal operator and drayage operators. The aim of the proposed …

Remediation Of Desiccation Cracking In Clayey Soils Through Bio-Cementation And Bottom Ash, Mark Vail

Theses and Dissertations

Desiccation cracking considerably impairs the hydraulic and mechanical properties of clayey soils and is critical to the long-term performance of infrastructure foundations and earth structures. Classical crack remediation methods are associated with high labor and maintenance costs or the usage of environment-unfriendly chemicals. Recycling waste materials and developing bio-mediated techniques have emerged as green and sustainable soil stabilization solutions. The objective of this study is to investigate the feasibility of soil crack remediation through the usage of microbial-induced calcite precipitation (MICP) and bottom ash admixtures. We carry out monotonic drying and cyclic drying-wetting tests to characterize the effects of bottom …

Evaluation Of Temporal Damage Progression In Concrete Structures Affected By Asr Using Data-Driven Methods, Vafa Soltangharaei

Theses and Dissertations

Alkali-silica reaction (ASR) is a chemical reaction, which causes damage in concrete structures such as bridges, dams, and nuclear containments and powerplant structures. The ASR-induced damage may endanger the integrity and serviceability of structures. Several methods such as visual inspection, petrographic analysis, demountable mechanical strain gauges, and cracking index have been utilized for study the effect of ASR on structures, which are not always efficient in early damage detection and some are destructive and prohibited in nuclear structures. Nondestructive methods and structural health monitoring techniques can be alternatives for the condition assessment of structures. Among the nondestructive methods, acoustic emission …

Evaluating Cracking Performance Of Polymer Enhanced And Fiber Reinforced Microsurface Mixtures Using Asphalt Laboratory Testing, George Joseph Shackil

Theses and Dissertations

This study presents a method to improve and evaluate the cracking resistance of microsurfacing mixtures using common asphalt laboratory testing. A preliminary optimal timing study and a study to evaluate improvements to cracking performance were conducted. The control mixture was based on NJDOT standard mix design specifications. Three mixtures were tested in this study: a fiber reinforced mixture using one-quarter inch glass fibers, an emulsion with increased SBR (polymer) contents, and a mixture using the one-quarter inch glass fibers combined with the increased polymer contents. Three laboratory tests were used to evaluate three different cracking resistance parameters: crack initiation (Semi-Circular …

Enhancing Facility Management For Existing Facilities With Building Information Modeling, Ryan Loeh

Theses and Dissertations

Building information modeling (BIM) refers to the process of creating a comprehensive three-dimensional (3D) model that allows for a seamless transition from design and construction to operation & maintenance during a building's lifecycle. While a majority of past research for building information modelling was focused on design and construction, research has shifted to operation, maintenance and renovation. This study investigates the feasibility of integrating BIM (Autodesk Revit) and facility management (BUILDER SMS). BUILDER SMS is currently used at the sponsor's facilities to encourage proactive maintenance and provide updated condition assessments. While both datasets have their own benefits, this study investigates …

Estimation Of Interior And Contents Damage Due To Wind Driven Rain Ingress Into Mid/High-Rise Buildings, Zhuoxuan Wei

Theses and Dissertations

Hurricanes can lead to the loss of millions of dollars and the death of hundreds of people. The increasing concentration of people in coastal cities, exacerbates this problem and results in greater hurricane damage to residential buildings. In particular, recent hurricanes in Florida have shown the vulnerability of mid/high-rise buildings (MHRB) to hurricane-induced water ingress. However, few damage models are able to produce realistic estimates of interior damage. To accurately estimate the interior and contents damage of mid/high-rise buildings due to water ingress during hurricanes, this thesis proposes a new physics-based methodology, which extends the results of previous work on …

Development Of Plane Rotating Traction System: Based On The High-Speed Rail (72+128+72) M Continuous Prestressed Concrete Beam Bridge, Weinan Wang

Theses and Dissertations

With the advent of rotate construction techniques, it is easy to build a new bridge crossing over existing structures, rivers and valleys quickly, easily and safely. Although the general concept of the rotating method is similar for different engineering characteristics, it is necessary to make some changes, which are more in line with the requirements of the particular project. Based on a 3-spans (72+128+72)m continuous concrete bridge, this paper presents a new rotation method, the down-slide-way unbalanced rotation system, which can save time and reduce cost compared to the up-slide-way rotation method. Through the improvements of the traction system and …

Polyester Polymer Concrete For Bridge Deck Overlays, Robert James Stevens

Theses and Dissertations

The objectives of this research were to 1) compile a synthesis of information about polyester polymer concrete (PPC) from the literature; 2) conduct a scanning tour to observe PPC construction, inspect in-service PPC overlays, and discuss topics related to PPC; 3) revise the existing Utah Department of Transportation (UDOT) PPC specification; 4) document a PPC field demonstration project; and 5) perform laboratory characterization of the material properties of field-mixed PPC. The scope of the research included a scanning tour, field testing, and laboratory experimentation. The objectives of the scanning tour included observation of a PPC overlay placement, inspection of existing …

Reliability Improvement On Feasibility Study For Selection Of Infrastructure Projects Using Data Mining And Machine Learning, Xi Hu

Theses and Dissertations

With the progressive development of infrastructure construction, conventional analytical methods such as correlation index, quantifying factors, and peer review are no longer satisfactory in support for decision-making of implementing an infrastructure project in the age of big data. This study proposes using a mathematical model named Fuzzy-Neural Comprehensive Evaluation Model (FNCEM) to improve the reliability of the feasibility study of infrastructure projects by using data mining and machine learning. Specifically, the data collection on time-series data, including traffic videos (278 Gigabytes) and historical weather data, uses transportation cameras and online searching, respectively. Meanwhile, the researcher sent out a questionnaire for …

Investigating The Effects Of Aggregate Size And Reinforcement On Asr Cracking In Concrete Structures Studied With Different Evaluation Methods, David Joseph Bianco

Theses and Dissertations

The objective of this thesis is to investigate different (non-destructive) evaluation methods to assess the effects of reactive aggregate size and reinforcement on ASR affected concrete. It has been shown in previous literature that reactive coarse aggregates lead to more expansion as opposed to reactive fine aggregates. However, there is a lack in the literature exhibiting this relationship using different evaluation methods, such as acoustic emission (AE) and ultrasonic pulse velocity (UPV). Also, the literature does not emphasize the role this relationship plays when the concrete is imposed with stress boundary conditions. Non-destructive test methods, including acoustic emission, are becoming …

A Life-Cycle Analysis Of The Thermal Energy Transfer In Prototypical Air Force Office Building Construction Using Best Value Insulation Standards, Michael E. Canfield

Theses and Dissertations

The United States Department of Defense (DoD) possesses over 560,000 buildings and structures around the world which require electricity to maintain and operate. The energy costs associated with the operations of these building is approximately $4 billion per year. Sustainable infrastructure management is a crucial opportunity to improve and establish a prudent, manageable, and successful DoD budget. This research identified, modeled, and simulated thermal energy-efficient standards in building construction in order to recognize the best value standards as opportunities for potential cost savings. EnergyPlus and OpenStudio Building Performance Simulation (BPS) software was used to model the energy flow into and …

An Analysis Of The Viability Of 3d-Printed Construction As An Alternative To Conventional Construction Methods In The Expeditionary Environment, Jeneé A. Jagoda

Theses and Dissertations

Conventional construction is believed by some to have reached its technological limit of performance, making it increasingly difficult for conventional construction methods to meet the U.S. military’s core standards of quality, cost, and timeliness in the expeditionary environment. While still in its infancy, 3D-printed construction has the potential to revolutionize the way the military performs construction in deployed environments. This research conducts a systematic review of the viability of 3D-printed construction to investigate whether or not it is now or could be a viable replacement for conventional construction methods, specifically in remote environments where conventional construction capability may be limited. …

An Analysis Of Tinker Air Force Base Thermal Spray Hazardous Waste Stream From 2003-2019 And Its Potential Reclamation, Amy E. Silverbush

Theses and Dissertations

The disposal of hazardous waste threatens the environment and human health. However, certain hazardous wastes can be recycled or reclaimed to alleviate environmental and financial impacts associated with its disposal and resource demand reduction. A hazardous powder produced by the United States Air Force stems from aircraft maintenance and is composed of metals and ceramics, called thermal spray. This waste can be purchased by an industrial recycler if the waste is composed of valuable metals. Historic data from the depot-level maintenance base Tinker Air Force Base initiated an analysis of annual thermal spray hazardous waste disposal fees, which combined with …

Comparison Of The Pfas Adsorption Capabilities Of A Coconut Shell Based Granular Activated Carbon And A Bituminous Coal Based Granular Activated Carbon, Matthew D. Holliday

Theses and Dissertations

This research compares the ability of two granular activated carbons (GAC) from different material sources to adsorb perfluoroalkyl substances (PFAS) in deionized water. A bottle study design was used to conduct the research, which measured the reduction in perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS). The carbons used were the bituminous coal based Calgon Filtrasorb 600 (F600) and the coconut shell based Evoqua AquaCarb 1230CX (AC1230CX). Additionally, the research focused on the rates at which the two contaminants were removed and compared them to previous research conducted with different forms of GAC. Results showed that both GACs were capable …

Civil Engineer Company Grade Officer Competency-Based Education Modeling, Scott R. Guerin

Theses and Dissertations

The importance of continuing education for professionals cannot be understated. This importance is doubly true for Air Force Civil Engineer Company Grade Officers who are members of not only the profession of engineering, but also the profession of arms. Air Force senior leaders understand this importance and required an update to the existing developmental education model, with a paradigm shift toward competency-based education and credentialing. Unfortunately, the Air Force Civil Engineer career field does not currently possess the required information to create a model in compliance with the senior leader directives. This research aims at establishing the required characteristics of …

The Effect Of Aeration Rate And Free-Floating Carrier Media On The Emission Of Bacillus Globigii In Bioaerosols, Andrew J. Owens

Theses and Dissertations

Aerosols produced by turbulent mechanical mixing and bubble aeration at Waste Water Treatment Plants (WWTPs) become bioaerosols with the entrainment of biological materials. Bioaerosols become a public health risk when human pathogens are present. This study evaluated bioaerosols containing Bacillus globigii (BG) spores, and the effects that aeration rate and the addition of Free-Floating Carrier Media (FFCM) had on the amount of BG spores collected following aerosolization. A series of laboratory-scale experiments investigated two different sizes of floating polystyrene spheres as FFCM and four different aeration rates. When the differences in compared aeration rates were sufficiently large, a positive correlation …

Analyzing Cost Effectiveness Of Photovoltaic Pavements, Ian N. Parks

Theses and Dissertations

The United States Air Force (USAF) is the largest consumer of energy within the Department of Defense (DoD). As such, the USAF is continually looking for ways to reduce consumption, as well improving network resiliency and assuring supply. One potential method for addressing these items is focusing on applications of renewable energy. A specific application of renewable energy that could greatly benefit the USAF if viable would be photovoltaic (PV) pavements. PV pavements would be able to capitalize upon the large swathes of pavements on Air Force (AF) installations, while not being hampered by other concerns such as clear zones …

Analysis Of Construction Management At Risk Projects For Unites States Air Force Applicability, Danielle K. Tabb

Theses and Dissertations

Construction management at risk is a project delivery method that sees widespread use in the private and public non-federal construction sectors. There is interest in the federal government of using a project delivery method such as construction management at risk. However, guiding regulations prohibit the federal government from using it as it is utilized in the private sector. This research analyzes private sector use of construction management at risk through a literature review and Delphi Panel, in order to determine its effects on project performance. The Delphi Panel consisted of two rounds of questions; the experts were selected through a …

Examining Healthy Community Design Characteristics And Its Influence On Physical Health, Alvin T. Yip

Theses and Dissertations

Current trends in obesity rates associated with the community layout constitutes research towards understanding the interaction between the two in order to improve the public's physical health. Successes in healthy community planning studies for the public can be harnessed and implemented within the microcosm of military bases to yield similar results. Four factors were recognized through an in-depth academic literature review that showed positive influence on physical health and physical activity. They are access to green space, highly connected pedestrian and bicycle networks, access to public transportation, and integrated mixed land use. The four healthy planning strategies formed the necessary …

Using Nano- And Micro- Structural Materials For Concrete Environmental Applications, Hala Nabeel Elia

Theses and Dissertations

Utilized globally in the construction industry, concrete is an integral component of homes, roads, airports, skyscrapers, and tunnels. Traditional concrete components are cement, fine aggregate (sand), coarse aggregate (gravel or crushed stone), and water. When cement and water compound together they will make a paste which binds all the aggregates together to make the concrete. Unfortunately, every one ton of cement manufactured emits 0.9 ton of CO2into the air. The goal of this two-part work was to obtain an environmentally friendly concrete. The first part used supplementary cementitious materials (SCM), fly ash and silica fume, to create concrete with high …

Splice Performance Of #6 Reinforcing Bars In Masonry With Self-Consolidating Grout, Annie Ruth Nielson

Theses and Dissertations

Reinforced masonry grouted using self-consolidating grout (SCG) is a relatively new and economically competitive option for construction, providing advantages such as reduced construction time, decreased noise and vibration, and reliable consolidation. However, SCG has different properties than conventional grout and its performance should be verified using current governing code requirements. The purpose of this research program was to determine the development length of spliced reinforcing bars in masonry grouted with SCG.Twelve masonry panels, four courses high and two and a half blocks wide, were constructed using 8-inch concrete masonry units, each with two pairs of vertically spliced #6 reinforcing bars. …

An Advanced Approach For Contract Time Determination In Highway Projects, Cuauhtemoc Torres Cantu

Theses and Dissertations

In project management, finishing a project on schedule is one of the most important aspects. The Texas Department of Transportation (TxDOT) has been experiencing delays in some projects that can be accounted to an inaccurate project time estimation process. This research presents the development of a user-friendly and comprehensive computer-based contract time determination system. The enhanced system implements probabilistic scheduling techniques such as Program Evaluation and Review Technique, and Monte Carlo Simulation. Additionally, the application of a lognormal two-point PERT method is explored in this study. The new system proposes the use of a database of production rates based on …

Multi-Facet Retrofit Approach To Improve Energy Efficiency Of Existing Class Of Single-Family Residential Buildings In Florida, Kwame Baffour Ohene Amoah

Theses and Dissertations

There are many approaches to incorporate energy efficiency measures (EEMs) into building through retrofit projects. Single-family buildings are an essential target for energy improvements because of their energy-saving potential and considerable market share. This study evaluates energy savings and cost-effectiveness of individual retrofit options. It proposes energy efficiency measures for an existing class of single-family homes constructed between the years of 1950 and 1970. The study uses a baseline building located in Melbourne, FL, as a case study. A survey via clustering data mining was conducted on Florida Single-Family Residential (SFR) buildings (1950 – 1970) to establish patterns of construction, …

Experimental Investigation Of Hydraulic Effects On Unsaturated Soils Behaviors, Muwafaq Awad

Theses and Dissertations

Geo-structures are frequently constructed in or on soils with unsaturated conditions and are subjected to variations of moisture contents due to seasonal changes. Even though unsaturated soil mechanics have been established for several decades, it has not been fully implemented in practice today because of a lack of understanding of the interaction between the soil, water, and air phases. Many experimental research studies have been conducted to improve the understanding of unsaturated behavior but these studies are typically limited to small soil elements tested under fully drained conditions. The goal of this research is to evaluate the effect of hydraulics …