Civil and Environmental Engineering Commons^™

Shear Behavior Of Reinforced Concrete Deep Beams Strengthened With Cfrp Laminates, Jon Erik Moren

Theses

Considerable research has been performed using CFRP plates bonded to normal reinforced concrete beams, the objective being to improve shear and flexural strength. However, very few tests have been performed on reinforced concrete deep beams with CFRP as shear reinforcement. The purpose of this experiment is to investigate the behavior of the deep beam in shear with various arrangements of Sika CarboDur laminates bonded to the sides. The beams were designed to be shear deficient with stirrups omitted, except at the supports and directly under the load. In total eight beams were tested, four with one-point loading and four with …

Mechanical Properties And Stress-Strain Behavior Of High Performance Concrete Under Uniaxial Compression, Pornchai Jiratatprasot

Theses

Many recent innovations in advanced concrete materials technology have made it possible to produce concrete with exceptional performance characteristics. High performance concrete (HPQ is defined as concrete that meets special performance and uniformity requirements that cannot always be achieved routinely by using conventional materials and normal mixing, placing, and curing practices. The importance of HPC to structural engineering is unquestionable. However, HPC is a relatively new material. Some results of research on conventional concrete are not entirely applicable. In this experiment, the main mechanical properties of HPC including compressive strength, modulus of elasticity, and Poisson's ratio were investigated and compared …

Characterization Of The Dependant Pile Capacity In Glacial Deposits By Dynamic Load Tests, Upendra L. Karna

Theses

A study of the effects of time on axial pile capacity in glacial deposits is presented in this report. The dynamic and static load database test results of the Route 21, Viaduct Replacement project are studied and analyzed. In this project two sizes (18-inch and 24-inch dia.) of closed end pipe piles varying in length 100 to 150 feet driven through highly variable glacial deposits were utilized. Within a small reach the subsurface conditions and the behavior of pile capacity with time varied considerably. About 112 piles were tested dynamically by Pile Driving Analyzer. Restriking was performed on fifty-nine piles …

Development And Application Of A Computer Simulation Tool For Ecological Risk Assessments, Haiyi Lu

Theses

In an effort to improve tools in ecological risk assessment (ERA), an ERA software tool was developed and applied. Based on a preliminary evaluation of existing ecorisk models, the relative deficiencies were identified and included the need for a user-friendly interface, an interactive database management system (DBMS), and a comprehensive evaluation of exposure pathways. In this research, Visual Basic (VB) 6.0 and Microsoft SQL server were selected for developing the Windows-based interface and local DBMS, respectively. For the exposure estimate, Yuma and Aberdeen Proving Grounds were identified as baseline ecosystems. Terrestrial and aquatic plant and animal receptor selection was based …

Reactive Media For Chromium Reduction Under Alkaline Conditions For Use In Permeable Reactive Barriers, Sachin V. Apte

Theses

The purpose of this study was to select the appropriate reactive media for chromate reduction to treat groundwater (high pH) with permeable reactive barriers. The study addresses groundwater contamination for three chromium refining sites located in Hudson County, New Jersey. The use of iron (Fe⁰) as a reactive medium was studied and found to be insufficient for use in permeable reactive barriers because of the high pH conditions of groundwater at these sites. Pyrite and iron (Fe⁰)-pyrite mixtures were studied as viable reactive media by considering their passivation kinetics, reductive capacities and solubility properties.

Column experiments …

Optimization Of Nitrogen Removal In Sequencing Batch Reactor, Suppakit Poonyachat

Theses

Operating parameters for sequencing batch reactor have the influenceon each substrate concentration. Concentration profile changes as operationparameters are changed. The study was conducted to model the variationin effluent concentration from sequencing batch reactor. MLVSS and cycletime are the parameters that were varied. Concentration in Fill, React,and Settle Period were calculated by using kinetic equations.

The results can show that these parameters have effects on the concentrationprofile. The increase of MLVSS can lower the concentration of BOD andammonium concentration in React period. Increasing MLVSS can show thatmore substrate utilization and nitrification process occur more rapidly.Concentration of nitrate at the end of …

Measurement Of Microcarrier Weighted Floc Using The Environmental Electron Microscope, Viriya Vithayaveroj

Theses

Utilizing the concept of coagulation in conjunction with the sediment enhancement by microcarrier, the microcarrier process has been demonstrated in a laboratory investigation as an effective and economic operation in removing colloidal particles in an aquatic system. The microcarrier, an inert aluminum silicate particulate (Ottawa Sand) of 53 to 75 micrometers in diameter was used in this study. The interaction between the flocs and the microcarriers plays an important role in the mixing process. The principal objective of this study is to examine the structural interaction between the flocs and the microcarrier.

The study was designed into two stages, the …

Intelligent Process For Uasb Reactors, Sita Mohan

Theses

The Upflow Anaerobic Sludge Blanket (UASB) reactor is widely used for the anaerobic treatment of concentrated municipal / industrial wastewaters and sludges. Ability to handle high organic loading rates and cost effectiveness are often the most cited merits of the UASB process. Numerous mathematical models have been developed to describe the process and mechanistic phenomena in these systems. However, evidence in the literature of these models having been applied, either as control or diagnostic tools is limited. The use of intelligent process control mechanisms can greatly ease problems associated with operating these reactor systems.

The objective of this study is …

Post-Cracking Tensile Properties Of Advanced Cementitious Materials And Ductility Of High Performance Concrete Beams, Wonsiri Punurai

Theses

In present direct tension tests, the complete stress-deformation curves, the resulting energy dissipated by damage, and the fracture energy of different types of cementitious composites, namely plain concrete, high strength concrete, normal fibrous concrete, high strength fibrous concrete, are studied and a ductility factor is calculated. It has been found that with the increasing strength of concrete due to the addition of the pozzoians such as silica fume and fly ash and when changing from normal strength to high strength, concrete ductility decreases. However, when fibers are combined with these matrices, concrete ductility increases. It is because of ductile steel …

Characterization Of Steel Corrosion In An Aggressive Environment, Sung Min Maeng

Theses

As part of the Sustainable Green Manufacturing Program, the corrosion resistance of sputtered tantalum is being studied in order to evaluate it as a replacement coating for electroplated chrome. To accomplish this, studies were conducted to evaluate corrosion properties of the gun barrel steel by employing corrosion rate and bulk measurements including x-ray diffraction (XRD), scanning electron microscopy (SEM)/energy dispersive x-ray spectroscopy (EDX), and x-ray fluorescence (XRF), as well as synchrotron-based x-ray absorption spectroscopy (XAS).

Corrosion behavior of steel immersed in an aggressive environment of 37.8 % hydrochloric acid at room temperature was investigated as a function of time from …

Modeling Of A Permeable Reactive Barrier, Guatam C. Ijoor

Theses

The focus of the presentstudy was centered on the modeling analysis to support the Permeable Reactive Barrier (PRB) design. The flow model formulated to simulate the Permeable Reactive Barrier System integrated the available geologic, hydro geologic and geo-chemical data from numerous recent installations to simulate a subsurface ground water scenario.

Different generic cases that a PRB system would fall into were identified based on its utility and aquifer conditions and then employed to produce different model adaptations. The different simulation codes and interfaces were evaluated, and the most expedient of them was used to simulate the Model.

The simulations were …

Coagulation And Disinfection By-Products Formation Potential Of Dissolved Organic Matter Fractions, Neeraj S. Pipada

Theses

Both the proposed United States Environmental Protection Agency (USEPA) Disinfectants- Disinfection By-Products and Enhanced Surface Water Treatment rules have provisions for minimizing the formation of undesirable precursors of disinfection by-products (DBPs) in drinking water Natural Organic Matter (NOM) contains many of the precursors to the DBPs formed following disinfection of drinking water. DAX-8 resin procedures were used to isolate and fractionate NOM into six dissolved organic matter (DOM) fractions; Hydrophobic acid (FA), base (FB), neutral (FN), and hydrophilic acid (PA), base (PB) and neutral (PN). Aluminum sulfate (alum) jar coagulation tests were performed to determine the optimum coagulation ranges of …

In Situ Enhancement Of Well Recovery By Pneumatic Media Injection, Michael Thomas Galbraith

Theses

The objective of this thesis was to develop a new process for enhancing recovery wells at hazardous waste sites. The process, known as an extended radius well (ERW), involves injection of ceramic beads directly into groundwater plumes to create drainage paths for liquid contaminants. This is a variant of Pneumatic Fracturing, which is a patented in situ remediation process developed to increase permeability of soil and rock formations by injection of high pressure gas.

The research study comprised laboratory investigations, engineering scale tests, and a field pilot demonstration. The laboratory investigations examined the properties of several candidate media to determine …

Design And Engineering Of A Tensile Fabric Structure, Jairo Rios

Theses

Fabric structures are designed in an iterative process between architect and engineer, analysis input and output, and detail and patterning. There are three main steps in designing a fabric structure: shape finding, loading, and patterning/ detailing.

Shapefinding consists of finding the shape of the fabric where the fabric forces are in equilibrium. This type of structure is geometrically nonlinear which require iterative analysis to converge on a unique solution.

The loading of the structure is similar to that of any conventional structures. The departure is in the major effects that suction and ponding have on fabric surfaces.

Usually the details …

Analysis And Modeling Of Ultrasound To Decontaminate Heavy Metals In Dredged Sediments, Ruvini Perera

Theses

Sediments contaminated with heavy metals due to past disposal practices threatens the environment and requires remediation. This research is an attempt to develop a technology to decontaminate heavy metals in the dredged sediments with an integrated set of processes using ultrasound. Acoustic cavitation caused by ultrasound energy can be used to remove chromium from the sediments. Two coupled processes were used to treat both coarse (Process#1) and fine (Process#2) fractions of the sediments. Full factorial experimental designs were carried out to evaluate the treatment technique and to statistically model and optimize the processes. The model for Process#1 had four contributing …

Ultrasound To Decontaminate Organics In Dredged Sediments, Kanya Veerawat

Theses

In this research, it was attempted to decontaminate and separate dredged sediments contaminated with organic compounds by the application of ultrasound energy coupled with sub-atmospheric pressures. The decontamination and separation of contaminated sediments was achieved by integrated two processes. For Process 1, ultrasound energy was used to decontaminate the sandy fraction in dredged sediments, and sub-atmospheric pressure was used to separate and remove fines. For Process 2, ultrasound was again used to decontaminate fines with bulk fluid, and sub-atmospheric pressure was used to remove the contaminants with water. Process 1 was evaluated and found to have four variables contributing to …

Production Of Submicron Aerosols By Powder Depressurization, Amit Haryani

Theses

Disaggregation of dry powders in shear flow has limitations in producing submicron particles. This study explores a new method for the production of submicron particles by the depressurization of powder aerosols. The depressurization mechanism is based on the rapid depressurization of the aggregated powder through a specially designed nozzle. As the pressure suddenly decreases from very high values inside the aggregates (800 psi) to ambient at the surface of such aggregates, disaggregation takes place due to the force exerted by the gas escaping through their pore structure.

he effect of various process parameters, namely: nozzle diameter, pressure and pretreatment with …

Fluorescence Spectroscopy For The Characterization Of Humic And Fulvic Acids And Their Disinfection By-Products Formation Potential, Ishvinder H. Kochar

Theses

Natural Organic Matter (NOM) plays a major role in the formation of undesirable organic by-products following disinfection/oxidation of drinking water. It is suspected that most precursors to disinfection by-products (DBPs) are humic although non-humic substances have not been studied and are suspected of also contributing to DBPs. NOM reacts with many of the disinfectants used to treat drinking water, such as chlorine, chioramine, and ozone, to form a variety of DBPs. Many of these DBPs have adverse health effects in humans (i.e. carcinogenic or mutagenic effects). The primary DBPs of concern include the trihalomethanes (THMs), haloacetic acids (HAAs), and haloacetonitrile …

Container Arrivals Forecasting Practice And Experience At Marine Terminals, Alexios C. Sideris

Theses

The advent of the container traffic in maritime transportation has led during its 40-year long history to novel perceptions and operation planning requirements for the port container terminal. A major requirement in this respect refers to the efficiency of the operations in the container transfer between the different modes. The current study presents a methodology on the development of a forecasting tool to access the service demand patterns at a marine terminal on per day basis. A set of forecasting models was introduced and their implementation difficulties were explored. The main effort in this approach was to replicate the distribution …

Reuse Of Cold Top Ex-Situ Vitrified Chromium Contaminated Soils In Hot Mix Asphalt Concrete, Gerald Charleston

Theses

This research investigated the pilot scale feasibility of the remediation of chromium contaminated soil through cold top ex-situ vitrification and the reuse of the vitrified products as highway construction aggregates. There are more than two million tons of chromite ore residues from the chromate extraction manufacturing leftover in Hudson County, New Jersey. They contained both un-leached hexavalent and unoxidized trivalent chromium. Hexavalent chromium is well known as a group A human carcinogen. It is also considered an environmental and health hazard. Of the many ex- situ and in-situ physical, chemical, and biological treatment technologies for chromate production waste, the ability …

The Determination Of 2-Methylisoborneol And Geosmin In Water Using Fluorescence Spectroscopy, Ramesh Chandra Sharma

Theses

Geosmin and 2-Methylisoborneol are responsible for imparting earthy, musty taste and odor qualities to water. The human threshold odor concentrations (TOCs) for 2-MIB and Geosmin vary over a wide range. TOCs of 10ng/1 for Geosmin and 30ng/1 for 2-MIB have been reported.

Currently available methods are time consuming and require use of sophisticated technique and expensive equipment.

Fluorescence spectroscopy has been successfully used in the identification of many organic compounds. Geosmin and 2-MIB have organic origin. This research explores the possibility of using the technique of fluorescence spectroscopy in the determination of Geosmin and 2-MIB. The excitation and emission wavelengths …

Composite Columns, Magnar Berge

Theses

The purpose of this thesis is to provide an introduction in the design of composite columns. The design methods according to AISC and Eurocode 4 are summarized and provide a procedure to design a composite column. In addition, equation are derived to determine the nominal flexural strength of typical composite cross-sections.

Stabilization Of Water Treatment Plant (Wtp) Residuals Using Sorbond, Rituraj Sinha

Theses

Disposal of water treatment plant (WTP) residuals has always been an important consideration for the water industry. Stringent water quality standards, environmental regulations, and unavailability of land for ultimate disposal affect disposal of large amounts of this residual. The search for alternate economical disposal options and beneficial use are probably the next most logical and economical step to take.

This study was performed to explore the possibility of stabilization of water treatment plant (WTP) residuals using additives. Three water treatment plant (WTP) residuals from treatment plants in New Jersey were used for the analysis. The objective of this research is …

Fluorescence Spectroscopy For The Characterization Of Total Organic Carbon And Disinfection By-Product Formation, Matthew Brendan Washington

Theses

One of the concerns facing the drinking water industry is the formation of disinfection by-products (DBPs) during the disinfection stage of treatment. Organic DBPs form during the oxidation of the natural organic matter (NOM) found in natural waters by the application of a disinfectant, such as chlorine.

NOM is composed of two aggregate materials, humic and non-humic substances. It is unknown which portions of NOM react with the oxidant to form DBPs. Methods used to predict the formation of DBPs include total organic carbon (TOC) analysis and Trihalomethane Formation Potential (THMFP), which are time consuming and do not give specific …

Impact Of Access Points On Multilane Highway Accidents, Tao Qu

Theses

This thesis presents an analysis of reported accidents on multilane highways and regression models that identify the primary explanatory variables that have a significant effect on accident rates midblock to signalized intersections. The analysis was based on traffic and reported accident data provided by New Jersey DOT. The access points per mile and the accident rates per million-vehicle-miles-traveled were analyzed based on a large number of roadway sections which were selected from five NJ State routes. Comparative accident analysis related with traffic and roadway geometric characteristics were performed. The analysis showed that approximately 30% of accidents occurred between intersections, which …

Characteristics Of Recycled Plastics And Applications For Highway Appurtenances, Keith Macbain

Theses

Recycling is gaining widespread support in many communities as an environmentally acceptable solution to the management of solid waste. The success of these recycling programs depends largely on the development of high-value end use for the recycled products. This research involves an experimental and analytical study on the development of high-value, high-volume end uses for recycled plastic shapes. The experimental part includes material tests to determine mechanical properties of various recycled plastics. A constitutive model is proposed and verified that can be used in characterization of recycled plastics. Bending tests of recycled plastic beams were performed to assess strength, stiffness …

The Study Of Permeability In Concrete, Jie Yuan

Theses

In this study, samples of regular, high performance, expansive and the polymer concrete and mortar were prepared for test of permeability and mechanical property. In the permeability measurement, water and an aqueous chemical solution were employed as the permeant.

The test results of the samples, ranging from 5.7 x 10-9 cm/sec to 1.0 x cm/sec for the permeability and 3800 psi to 10600 psi for compression strength, indicated that the polymer coated concrete has the lowest permeability among the concretes and high performance concrete has the highest compression strength . The finding leads to the possibility that a high strength …

An Analytical Approach To Toxic Substance Replacement In Support Of Pollution Prevention, Ithan B. Zimmer

Theses

In support of pollution prevention and in accordance with Executive Order 12356 concerning pollution prevention, all federal agencies must comply with the Toxic Release Inventory (TRI) chemical release reduction and pollution prevention planning. The inventory lists hundreds of chemicals and choosing those to replace and finding actual replacement chemicals or procedures is not always clear. This study focuses on an analytical approach to this problem by understanding the application of two substances. The representative chemicals are two volatile organic compounds (VOC), ethyl ether and ethanol, used as solvents in ammunition manufacturing.

Thirteen military specifications provide the cases involving ether. Ethanol's …

Analysis And Modeling Of Ultrasound Enhanced Soil Washing Process, Kamalavathany Rajaratnam

Theses

In this research, statistical analysis of data from ultrasound enhanced soil washing process was performed. The process was optimized using a statistical model. The model had four factors namely power, solvent:soil, surfactant, and dwell time as process variables. The percentage of removal efficiency was considered as the dependent variable. The results from two full and one partial factorial designs were analysed. Interactions up to third order were considered in the analysis, but the results from full factorial design showed that those of order higher than second had insignificant contributions to the removal of contaminants. Since the higher order interactions of …

Enhancing The Bioavailability Of Sorbed Pollutants From Sediments Using Ultrasound, Rachel Mathew

Theses

Many organic compounds, that enter aquatic systems have a strong tendency to sorb onto particulate matter which may be present in suspension or as sediment. Numerous studies have shown that the sediment in aquatic systems concentrate contaminants several orders of magnitude greater than the concentration in the aqueous phase. Particulate associated contaminants in sediments are not easily bioavailable. Hence the efficacy of any treatment technology would be strongly undermined if the contaminants are not made available for microbial utilization. Sediment associated contaminants can be made biologically available to various microorganisms under certain conditions.

In this study, desorption studies were conducted …