Civil and Environmental Engineering Commons^™

Improved Methodologies In Modeling And Predicting Failure In Aashto M-180 Guardrail Steel Using Finite Element Analysis – Phase I, Brandt M. Humphrey, Robert W. Bielenberg, Ronald K. Faller, John D. Reid, Mehrdad Negahban

Nebraska Department of Transportation: Research Reports

No abstract provided.

Midwest Guardrail System (Mgs) Placed Adjacent To A 1v:2h Fill Slope With 6-Ft Posts, Austin J. Haase, Justine E. Kohtz, Karla A. Lechtenberg, John D. Reid, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

No abstract provided.

Design Procedures Of Retrofitted Bridge Rail, Richard L. Wood, Yijun Liao, Mohammad E. Mohammadi, Jordan Wipf

Nebraska Department of Transportation: Research Reports

The use of shallow embedment anchors in concrete is essential for retrofit applications; however, the combination of steel anchors, chemical adhesive, and concrete acting as a single tensile mechanism creates uncertainties in anchor strength and failure modes. Differences in concrete compressive strengths and in specifications of adhesives between manufacturers increases uncertainty further. In addition to these issues, prior research conducted by others examines the behavior of such anchors with respect to cracked versus uncracked concrete, partial bonding of the embedded length, and strength reductions due to anchor proximity to edges. While it is understood, anchors require a proper installation detail, …

Identifying And Addressing Soil Property Issues Affecting Roadside Vegetation Establishment, Xu Li, Martha Mamo, Walter H. Schacht, Tala Awada, Humberto Blanco-Canqui

Nebraska Department of Transportation: Research Reports

Attaining adequate vegetation cover along highways is important for NDOR to comply with EPA’s stormwater regulations. However, low plant cover is a common problem on shoulders (first 16 feet off the pavement) of many highways in Nebraska. The ultimate goal of this study is to identify cost-effective engineering solutions that assure adequate seed beds (i.e., soil conditions) for establishment of selected seeding mixtures. The objectives of this study are to (1) characterize the soil properties along roadsides where vegetation stands have not developed well, and (2) verify the effects of select soil property parameters on plant germination and establishment.

Sampling …

Use Of Recycled Crushed Concrete (Rcc) Fines For Potential Soil Stabilization, Lindeman Mark, Varilek Brandon, Lieska Halsey, Rick Gloe, Maria Olomi

Nebraska Department of Transportation: Research Reports

This study evaluated the use of Recycled Crushed Concrete (RCC) Fines for potential soil stabilization. Soil stabilization is the enhancement of subgrade stability to improve the constructability of successive pavement layers. Use of RCC fines may not only provide less costly alternatives for subgrade stabilization, but their use may also alleviate landfill disposal challenges.

Class C Fly Ash In Pavements, Kromel E. Hanna, George Morcous, Maher K. Tadros

Nebraska Department of Transportation: Research Reports

No abstract provided.

Performance Assessment Of Deteriorated And Retrofitted Steel Hp Piles, Joshua Steelman, Steven Stauffer

Nebraska Department of Transportation: Research Reports

No abstract provided.

Mash Test Nos. 3-11 And 3-10 On A Non-Proprietary Cable Median Barrier, Justine E. Kohtz, Robert W. Bielenberg, Scott K. Rosenbaugh, Ronald K. Faller, Karla A. Lechtenberg, John D. Reid

Nebraska Department of Transportation: Research Reports

The Midwest States Pooled Fund has been developing a new non-proprietary cable median barrier. This system incorporates four evenly spaced cables, Midwest Weak Posts spaced at 8 to 16 ft (2.4 to 4.9 m) intervals, and a bolted, tabbed bracket to attach the cables to each post. Full-scale crash testing was needed to evaluate the barrier’s safety performance. According to the Manual for Assessing Safety Hardware (MASH) updated/proposed testing matrix for cable barriers installed within a 6H:1V or median ditch, a series of eight full-scale tests are required to evaluate the safety performance of a system. A ninth test is …

Continued Development Of A Non-Proprietary, High-Tension, Cable End Terminal System, Jennifer D. Schmidt, Robert W. Bielenberg, John D. Reid, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

A non-proprietary, cable guardrail system is currently under development for the Midwest States Pooled Fund Program. A cable guardrail end terminal was necessary to accompany the cable guardrail system. The objective of this research project was to develop design recommendations for the cable end terminal. Bogie testing that was previously completed on a design concept indicated delayed cable release, which was an undesired performance that led to vehicle instabilities. Several design changes were recommended for better end terminal performance and to reflect the changes made to the cable median barrier. An LS-DYNA model of the modified cable end terminal was …

Cable-To-Post Attachments For Use In Non-Proprietary High-Tension Cable Median Barrier – Phase Ii, Scott K. Rosenbaugh, Robert W. Bielenberg, Jessica L. Lingenfelter, Ronald K. Faller, John D. Reid, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

The objective of this study was to reevaluate and improve the existing cable-to-post attachment hardware that is utilized in the non-proprietary cable barrier being developed at MwRSF. The study focused on redesigning the bolted, tabbed bracket (V10) to eliminate the bolt, reduce the number of components per bracket, eliminate the need for tools during installation, and reduce the number of small parts. Three attachment concepts were selected for evaluation through dynamic testing: (1) the key plate attachment; (2) the wire lock pin attachment; and (3) the pinned back attachment. Each attachment prototype was subjected to two vertical and two lateral …

Evaluation Of Lightweight Pieces In Aggregates, Mark Lindemann, Doug Macke, Jim Wilken, John Ebito, Mark Hassler, Lieska Halsey, Bob Seger

Nebraska Department of Transportation: Research Reports

Nebraska Department of Roads (NDOR) Material and Research (M&R) Division started an evaluation to determined injurious deleterious lightweight pieces of aggregate from a dry pit location, as a result of field observations from a project stock pile. This brief summary presents the field observation and laboratory testing evaluations to determine the percent of lightweight pieces in aggregate.

Evaluation Of Lightweight Pieces In Aggregates, Mark Lindemann, Doug Macke, Jim Wilken, John Ebito, Mark Hassler, Lieska Halsey, Bob Seger

Nebraska Department of Transportation: Research Reports

No abstract provided.

Active Traffic Management Case Study: Phase 1, Anuj Sharma, Shuo Wang, Aemal Khattak

Nebraska Department of Transportation: Research Reports

This study developed a systematic approach for using data from multiple sources to provide active traffic management solutions. The feasibility of two active traffic management solutions is analyzed in this report: ramp-metering and real-time crash risk estimation and prediction. Using a combined dataset containing traffic, weather, and crash data, this study assessed crash likelihood on urban freeways and evaluated the economic feasibility of providing a ramp metering solution. A case study of freeway segments in Omaha, Nebraska, was conducted. The impact of rain, snow, congestion, and other factors on crash risk was analyzed using a binary probit model, and one …

Midwest Guardrail System (Mgs) With An Omitted Post, Jessica L. Lingenfelter, Scott Rosenbaugh, Robert W. Bielenberg, Karla A. Lechtenberg, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

The objective of this research study was to evaluate the MGS (31” tall W-beam guardrail) with an omitted post according to the safety performance criteria provided in MASH. A single full-scale crash test was conducted with the 2270P pickup truck in accordance with MASH test no. 3-11. The small car test, test no. 3-10, was deemed unnecessary as the pickup truck test would result in higher rail loads, a greater propensity for rail rupture, and a greater risk of failure. The test installation utilized standard 6-ft (1.8-m) long steel guardrail posts with 12-in. (305-mm) deep blockouts. A single post was …

Mitigating Pavement Edge Drop Off, Wayne Jensen, Niles Uerling

Nebraska Department of Transportation: Research Reports

The objective of this research was to investigate and document practices currently being used by the Nebraska Department of Roads (NDOR) districts and other State DOTs to mitigate pavement edge drop off. The NDOR has developed (or borrowed) and is currently incorporating into its standard practices several procedures that significantly decrease the incidence and magnitude of pavement edge-drop off. As these practices become more fully integrated into highway reconstruction projects, pavement edge drop off is expected to decrease dramatically. Localized areas of pavement edge drop off along paved lanes with bare or vegetated shoulders were noted as posing particular problems …

Nebraska Data Collection, Keyvan Zare Rami, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

Automated pavement performance data collection is a method that uses advanced technology to collect detailed road surface distress information at traffic speed. Agencies are driven to use automated survey techniques to enhance or replace their current manual distress survey because of the advantages of objective measurements, safety benefits, and reduced measurement time. As agencies move toward the transition to fully automated data collection methods, there are common concerns regarding how the output of the new method will match the current manual survey ratings and how they will be adopted into the existing Pavement Management System (PMS). This study evaluates the …

Development Of A Semicircular Bend (Scb) Test Method For Performance Testing Of Nebraska Asphalt Mixtures, Gabriel Nsengiyumva, Yong-Rak Kim, Taesun You

Nebraska Department of Transportation: Research Reports

No abstract provided.

Mash Test Nos. 3-17 And 3-11 On A Non-Proprietary Cable Median Barrier, Robert W. Bielenberg, Scott K. Rosenbaugh, Ronald K. Faller, Brandt M. Humphrey, Tyler L. Schmidt, John D. Reid

Nebraska Department of Transportation: Research Reports

No abstract provided.

Integrated 3d Bridge-Condition Visualization (Bcv) To Facilitate Element-Based Bridge Condition Rating (Ebcr), Zhigang Shen, Wayne Jensen

Nebraska Department of Transportation: Research Reports

Routine inspection and maintenance records are essential for bridges to function well throughout their intended lifespan. Although existing bridge management systems are efficient at data storage, it is difficult to conduct comprehensive data analysis and management due to the lack of data integration mechanism. Engineers have to manually put many pieces of bridge drawings and inspection data together to make maintenance or repair/rehab decisions. Building information modeling (BIM) can be applied in bridge asset management area, including bridge inspection/rating to help to integrate the many data pieces. In this project we developed a 3D bridge inspection data management system, using …

Mash Tl-4 Crash Testing And Evaluation Of The Restore Barrier, Jennifer D. Schmidt, Tyler L. Schmidt, Ronald K. Faller, Robert W. Bielenberg, John D. Reid, James C. Holloway, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

Three full-scale vehicle crash tests were conducted according to the MASH Test Level 4 (TL-4) safety performance criteria on a restorable and reusable energy-absorbing roadside/median barrier, designated the RESTORE barrier. The system utilized for test nos. SFH-1 through SFH-3 was 240 ft (73.2 m) long with a nominal height of 38⅝ in. (981 mm). The barrier consisted of an upper steel tube rail attached to the top of 20-ft (6.1-m) long x 22.-in. (565-mm) wide precast concrete beams connected with wedge-shaped joints and supported by 11⅝-in. (295-mm) tall rubber posts and steel skids.

In test no. SFH-1, a 5,021-lb (2,277-kg) …

Evaluation Of Concrete Grinding Residue (Cgr) Slurry Application On Vegetation And Soil Responses Along Nebraska State Highway 31, Martha Mamo, Dennis L. Mccallister, Walter H. Schacht

Nebraska Department of Transportation: Research Reports

No abstract provided.

Development And Evaluation Of Weak-Post W-Beam Guardrail In Mow Strips, Scott K. Rosenbaugh, Ronald K. Faller, Karla A. Lechtenberg, James C. Holloway

Nebraska Department of Transportation: Research Reports

The objective of this study was to adapt and evaluate a weak-post, W-beam guardrail system for use within mow strips and other pavements. The weak-post guardrail system was originally designed as the MGS bridge rail and has also been adapted for use on culverts. It was envisioned that the weak-post design would absorb the impact forces and prevent damage to the mow strips, thereby minimizing maintenance and repair costs.

Evaluation of the weak posts in mow strips began with three rounds of dynamic bogie testing. Round 1 of bogie testing showed that 4-in. (102-mm) thick concrete would sustain only minor …

Conceptual Development Of An Impact-Attenuation System For Intersecting Roadways, Joseph G. Putjenter, Robert W. Bielenberg, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Longitudinal barriers are commonly used to shield hazards, including stiff bridge rail ends and slopes. In some locations, a secondary roadway intersects the primary roadway within the guardrail’s length-of-need (LON). Some intersections may have as little as 15 ft (4.6 m) between the intersection and beginning of the bridge railing, which require short-radius guardrail systems. One short-radius guardrail system has passed several crash tests under AASHTO Manual for Assessing Safety Hardware (MASH) standards.

Site conditions provided by the Nebraska Department of Roads were used to determine the constraints for a new safety treatment for intersecting roadways and include intersection radii, …

Mgs Dynamic Deflections And Working Widths At Lower Speeds, Nicholas A. Weiland, Cody S. Stolle, John D. Reid, Ronald K. Faller, Robert W. Bielenberg, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

The Midwest Guardrail System (MGS) has been full-scale crash tested in many configurations, including installations adjacent to slopes, with different types of wood posts, with and without blockouts, for culvert and bridge applications, and at high flare rates. Although the performance of the MGS and the dynamic deflection and working width of the barrier have been examined, little is known about the dynamic deflection and working width of the MGS when impacted at lower speeds. The MGS is a relatively low-cost barrier, and the Test Level 3 (TL-3) version could be installed for TL-2 and TL-1 applications. The barrier is …

Performance Characteristics Of Posts Embedded In Soil, Brandt M. Humphrey, Karla A. Lechtenberg, John D. Reid, Ronald K. Faller, James C. Holloway

Nebraska Department of Transportation: Research Reports

The primary objective of this research study was to determine the post-soil impact reaction of W6x8.5 (W150x12.6) steel posts and 6-in. x 8-in. (152-mm x 203-mm) Southern Yellow Pine (SYP) posts, specifically along the weak axis. Five bogie tests were conducted on W6x8.5 (W150x12.6) A992 steel posts with a length of 72 in. with embedment depths ranging between of 24 and 40 in. (610 and 1,016 mm). Four bogies tests were conducted on 6-in. x 8-in. (152 mm x 203 mm) SYP posts embedded at depths ranging between 30 and 40 in. (735 and 1,016 mm). The target impact conditions …

Design And Evaluation Of An Energy-Absorbing, Reusable Roadside/Median Barrier, Scott Rosenbaugh, Ronald K. Faller, Robert W. Bielenberg, James C. Holloway, Karla A. Lechtenberg, Jennifer D. Schmidt, John D. Reid, Justice E. Kohtz

Nebraska Department of Transportation: Research Reports

No abstract provided.

Evaluation Of Thin Asphalt Overlay Practice Preserving Nebraska's Asphalt Pavement, Soohyok Im, Yong-Rak Kim, Hamzeh Haghshenas Fatmehsari, Gabriel Nsengiyumva, Taesun You

Nebraska Department of Transportation: Research Reports

No abstract provided.

Cable-To-Post Attachments For Use In Non-Proprietary High-Tension Cable Median Barrier – Phase Ii, Scott K. Rosenbaugh, Robert W. Bielenberg, Brandt M. Humphrey, Ronald K. Faller, John D. Reid, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

The research objectives reported herein were based on further development of cable-to-post attachment hardware for use in the non-proprietary high-tension cable barrier system. Specifically, this project aimed to develop and evaluate alternative attachment designs for the bolted, tabbed bracket and evaluate the use of a larger diameter, keeper rod for use in the top cable attachment. From a group of over 25 alternative attachment concepts, two tabbed bracket designs were selected for evaluation through dynamic component testing: 1) the lateral shear plate attachment and 2) the drop-in shear plate attachment. The drop-in shear plate concept did not perform as intended, …

Swift Fox Abundance Along The Heartland Expressway Corridor In Nebraska, Marc Albrecht

Nebraska Department of Transportation: Research Reports

No abstract provided.

Design Of An Improved Post For Use In A Non-Proprietary High-Tension Cable Median Barrier, Robert W. Bielenberg, Ronald K. Faller, Karla A. Lechtenberg, Tyler L. Schmidt, Scott K. Rosenbaugh, John D. Reid, Dean L. Sicking

Nebraska Department of Transportation: Research Reports

The objective of this research study was to develop a revised post section for the non-proprietary high-tension cable median barrier that improved the safety and function of the post by lowering strong-axis forces. A total of twenty dynamic component tests were performed, along with one cable pull test – ten tests with the 7-gauge C-section post, eight with the 10-gauge C-Section posts, and three with the Midwest Weak Post (MWP). The tests were conducted with the posts installed in either a compacted, crushed limestone soil or a rigid sleeve in order to determine the force vs. deflection and energy vs. …