Civil and Environmental Engineering Commons^™

Comparing The Effect Of Carbon Sources, Lactate And Whey, On Biological Reductive Dechlorination Of Tce In Laboratory Flow Through Columns, Sarah M. Kissell

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Trichloroethylene (TCE) is a chlorinated solvent most commonly used as an industrial degreaser for cleaning mechanical equipment. Historic improper management and disposal of TCE has resulted in contaminated soil and groundwater across the United States, including Hill Air Force Base in Utah. The abundance of TCE in the environment presents a public health risk because it is categorized as a Group 1 carcinogen by the International Agency for Research on Cancer (IARC).

The purpose of this study was to improve the bioremediation techniques of biostimulation and bioaugmentation. A continuous flow-through column study was performed where columns packed with aquifer material …

Prestress Losses And Temperature Effects On A Deck Bulb Tee Girder Bridge, Phillip Powelson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Utah Transportation Center (UTC), in partnership with the Mountain Plains Consortium (MPC), sponsored a study to investigate the differences in prestress losses and temperature gradients in a concrete deck bulb tee girder bridge. The Millville Bridge was built as an access point to the Ridgeline High School in Millville, Utah. The bridge was built in 2016 and presently supports two lanes of traffic.

Changes in prestress were measured with a total of 16 vibrating wire strain gauges located at four cross-sections. Temperature gradients were measured with a total of 50 thermocouples located at five cross-section locations, four of which …

Design Of A Metadata Framework For The Environmental Models With An Example Hydrologic Application In Hydroshare, Mohamed M. Morsy, Jonathan L. Goodall, Anthony M. Castronova, Pabitra Dash, Venkatesh Merwade, Jeffrey M. Sadler, Mohammad Adnan Rajib, Jeffery S. Horsburgh, David G. Tarboton

Civil and Environmental Engineering Faculty Publications

Environmental modelers rely on a variety of computational models to make predictions, test hypotheses, and address specific problems related to environmental science and natural resource management. Scientists and engineers must devote significant effort to preparing these computational models. While significant attention has been devoted to sharing and reusing environmental data, less attention has been devoted to sharing and reusing environmental models. A first step toward increasing environmental model sharing and reuse is to define a general metadata framework for models that is flexible and, therefore, applicable across the wide variety of models used by environmental modelers. This paper proposes a …

Potential Crop Evapotranspiration And Surface Evaporation Estimates Via A Gridded Weather Forcing Dataset, Clayton S. Lewis, L. Niel Allen

Civil and Environmental Engineering Faculty Publications

Absent local weather stations, a gridded weather dataset can provide information useful for water management in irrigated areas including potential crop evapotranspiration calculations. In estimating crop irrigation requirements and surface evaporation in Utah, United States of America, methodology and software were developed using the ASCE Standardized Penman-Monteith Reference Evapotranspiration equation with input climate drivers from the North American Land Data Assimilation System (NLDAS) gridded weather forcing dataset and a digital elevation model. A simple procedure was devised to correct bias in NLDAS relative humidity and air temperature data based on comparison to weather data from ground stations. Potential evapotranspiration was …

Wildfire In Utah: The Physical And Economic Consequences Of Wildfire, Paul Mark Jakus, Man-Keun Kim, Randy S. Martin, Ian Hammond, Edd Hammill, Nancy O. Mesner, Jacob Stout

Watershed Sciences Faculty Publications

PRELUDE

On June 26, 2012 a lightning strike ignited a wildfire in the Manti-La Sal National Forest of central Utah’s Carbon and Emery counties (Figure P.1). By the time the Seeley wildfire was contained three weeks later, some 48,000 acres of federal, state, and private land had been burned and $8.7 million in suppression costs expended (Styler 2012). According to the Monitoring Trends in Burn Severity (MTBS.gov) project, nearly one-third of the acreage was severely burned, damaging vegetation and soils for years to come. Severe burns vastly increase the erosion potential of burnt landscapes, and the steep lands of Huntington …

Exercise - Calculate Reservoir Performance Metrics - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

No abstract provided.

Gams Handout 1, Ethan Yang

All ECSTATIC Materials

No abstract provided.

Gams Handout 4, Ethan Yang

All ECSTATIC Materials

No abstract provided.

Gams Handout 2, Ethan Yang

All ECSTATIC Materials

No abstract provided.

Gams Handout 3, Ethan Yang

All ECSTATIC Materials

No abstract provided.

Exercise - Choose A Manager To Learn Multi-Criteria Decision Analysis - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

A prompt for an in-class exercise, so that students can learn basic principles of multi-criteria decision analysis. The ideal place for this exercise is to have it before the formal lecture of multi-criteria decision analysis. The students will start to gain an intuitive understanding of how to transform preferences to scores, how to weight the metrics, and how to make a final decision.

Water Resource Systems And Management (Spring 2017) - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

No abstract provided.

Introduction To Reservoir Analysis - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

Introduction to reservoirs, lecture from Water Resource Systems and Management (Spring 2017), University of Colorado Boulder. By Joseph Kasprzyk. Learning goals include (i) introducing what a reservoir is, (ii) apply control volume and conservation of mass principles to analyze storage in natural lakes and reservoirs (iii) calculate required storage size for reservoirs using basic techniques (iv) define reservoir terms including safe yield and critical period (v) discuss dam building trends in the US and globally.

Introduction To Water Resources Systems - University Of Colorado Boulder, Joseph Kasprzyk

All ECSTATIC Materials

This is the introductory lecture to a Water Resource Systems and Management class from Spring 2017 at the University of Colorado Boulder, by Joseph Kasprzyk. Learning goals include (i) defining integrated water resources management, (ii) identifying Colorado water management issues (ii) identifying how RiverWare simulation and optimization can be used to develop water plans (iii) use the HyMod model to perform rainfall-runoff modeling (iv) generating random parameter samples and understanding how parameter uncertainty affects model results.

Stochastic Hydrology, Meghna Babbar-Sebens

All ECSTATIC Materials

Syllabus for graduate class in Stochastic Hydrology

Case Study For Guided Project In Stochastic Hydrology, Meghna Babbar-Sebens

All ECSTATIC Materials

Attached are two guided project activities for hydrology and climate data of Eagle Creek Watershed, Indiana, USA. The zip files have flow and precipitation datasets at daily, monthly, and annual time scales.

Optimization In Water Resources Engineering, Meghna Babbar-Sebens

All ECSTATIC Materials

No abstract provided.

Enhancing Ductility Of Wwr Slabs, Mohamed Shwani, Taylor J. Sorensen, Ethan Pickett, Parker Syndergaard, Marc Maguire

Civil and Environmental Engineering Faculty Publications

A series of research studies have recently identified an issue called strain localization in welded wire reinforced (WWR) members. This phenomenon reportedly concentrates strains at welded cross wire locations and severely limit ductility. Those that identified the phenomenon used it to imply that WWR is unsafe because it does not warn of failure. This research program is investigating details to mitigate the strain localization effect and demonstrate the WWR can be used safely. Sixteen beams have been constructed using WWR and rebar with various cross wire spacing, using a realistic design. The strain localization phenomenon was not demonstrated, but WWR …

Nutrient Processes At The Stream-Lake Interface For A Channelized Versus Unmodified Stream Mouth, Richard G. Niswonger, Ramon C. Naranjo, David R. Smith, Jim E. Constantz, Kip K. Allander, Donald O. Rosenberry, Bethany T. Neilson, Michael R. Rosen, David A. Stonestrom

Civil and Environmental Engineering Faculty Publications

Inorganic forms of nitrogen and phosphorous impact freshwater lakes by stimulating primary production and affecting water quality and ecosystem health. Communities around the world are motivated to sustain and restore freshwater resources and are interested in processes controlling nutrient inputs. We studied the environment where streams flow into lakes, referred to as the stream-lake interface (SLI), for a channelized and unmodified stream outlet. Channelization is done to protect infrastructure or recreational beach areas. We collected hydraulic and nutrient data for surface water and shallow groundwater in two SLIs to develop conceptual models that describe characteristics that are representative of these …

Developing A General Methodology For Evaluating Composite Action In Insulated Wall Panels, Jaiden Olsen, Salam Al-Rubaye, Taylor J. Sorensen, Marc Maguire

Civil and Environmental Engineering Faculty Publications

Precast concrete sandwich wall panels(PCSWPs) have been in use for over 60 years. They provide a very efficient building envelope for many buildings. Characteristic PCSWPs comprise an outer and inner layer (or wythe) of concrete separated by an insulating material. To use all of the material as efficiently as possible, the layers are attached by connectors which penetrate through the insulating layer and are embedded in either concrete wythe. These connectors make it possible for both layers of the wall to work together when resisting loads. The connectors are made out of plastic, or FRP, to prevent heat transfer from …

Investigating Composite Action At Ultimate For Commercial Sandwich Panel Composite Connectors, Salam Al-Rubaye, Taylor J. Sorensen, Marc Maguire

Civil and Environmental Engineering Faculty Publications

To achieve full or partial-composite action in prestressed concrete sandwich panel walls, the engineer must obtain a percent composite action from a connector manufacturer, making some engineers uncomfortable. Engineers are dependent upon the recommendations given by the connector manufacturers to establish their designs. This project tested six full-scale sandwich panel walls to evaluate the percent composite action of various connectors and compare the results to those provided by the composite connector manufacturers. This study concluded that the reported degrees of composite action from each manufacturer are considered conservative in all instances for the connectors tested in this paper. Additionally, the …

Hydroshare Gis: Visualizing Spatial Data In The Cloud, Shawn Crawley, Daniel P. Ames, Zhiyu Li, David G. Tarboton

Civil and Environmental Engineering Faculty Publications

Cloud-based data management systems are more conducive to collaborative efforts when they are integrated with cloud-computing tools that interact with their stored data. HydroShare, a web based data management system for climate and water data, has implemented an Application Programming Interface and a web application platform deployed using Tethys Platform to encourage the development of apps that interact with its data. HydroShare GIS is the result of one such development effort to provide cloud-based visualization of spatial data stored in HydroShare. It functions by accessing the spatial metadata contained within the HydroShare resource data model and overlaying datasets as layers …

Vicarious Calibration Of Suas Thermal Imagery For Scientific Remote Sensing Applications [B53h-0607], Alfonso F. Torres-Rua

AggieAir Presentations

Small Unmanned Aerial Systems (sUAS) have become an accessible technology for collection of spatially distributed temperature data at fine resolution. Nevertheless, lack of standard procedures for atmospheric temperature correction can have an adverse impact on the conclusions and replicability of studies using this technology. This work presents a vicarious calibration methodology for sUAS thermal imagery traceable back to NIST standards. For this methodology, a 3-yr. data collection campaign with a sUAS technology, called “AggieAir”, developed at the Utah Water Research Laboratory, was performed under different daytime conditions. A comparison between original and vicarious calibration for the sUAS thermal imagery is …

Investigating And Improving Bridge Management System Methodologies Under Uncertainty, Minwoo Chang

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This dissertation presents a novel procedure to select explanatory variables, without the influence of human bias, for deterioration model development using National Bridge Inventory (NBI) data. Using NBI information, including geometric data and climate information, candidate explanatory variables can be converted into normalized numeric values and analyzed prior to the development of deterministic or stochastic deterioration models. The prevailing approach for explanatory variable selection is to use expert opinion solicited from experienced engineers. This may introduce human influenced biases into the deterioration modeling process. A framework using Least Absolute Shrinkage and Selection Operator (LASSO) penalized regression and covariance analysis are …

Ncer Assistance Agreement Annual Progress Report For Grant #83582401 - Assessment Of Stormwater Harvesting Via Manage Aquifer Recharge (Mar) To Develop New Water Supplies In The Arid West: The Salt Lake Valley Example, Ryan Dupont, Joan E. Mclean, Richard C. Peralta, Sarah E. Null, Douglas B. Jackson-Smith

Civil and Environmental Engineering Faculty Publications

The aims of the original proposed project remain the same, that is, to test the hypothesis that Managed Aquifer Recharge (MAR) for stormwater harvesting is a technically feasible, socially and environmentally acceptable, economically viable, and permittable option for developing new water supplies for arid Western urban ecosystems experiencing increasing population, and climate change pressures on existing water resources. The project is being carried out via three distinct but integrated components that include: 1) Monitoring of existing distributed Managed Aquifer Recharge (MAR) harvesting schemes involving a growing number of demonstration Green Infrastructure (GI) test sites; 2) Integrated stormwater/vadose zone/groundwater/ ecosystem services …

Cee Dept. Announces Water Cluster Hire | College Of Engineering, Usu College Of Engineering

College of Engineering News

The Department of Civil and Environmental Engineering (CEE) seeks talented applicants for a cluster hire of three tenure eligible positions at the assistant or associate level whose research will yield more holistic approaches to solving water problems in natural, built, and/or agricultural environments. We seek bright, creative and interdisciplinary researchers who can increase Utah State University’s (USU) capacity to lead and develop the next generation of resilient solutions to water problems in these linked environments. We especially seek applicants with the passion and ability to work with others from a broad range of disciplines to advance fundamentally new and innovative …

Usu Awwa Tour | Civil And Environmental Engineering, Usu College Of Engineering

College of Engineering News

The newly formed student chapter of the American Water Works Association (AWWA) recently went on tours of two water facilities. In early October, ten students attend a tour of the Utah Water Research Laboratory here at USU. The students enjoyed seeing applied research that is conducted at the lab. This week, the chapter also visited the Franklin Idaho Drinking Water Treatment Plant. This exposure to the industry has been a remarkable professional and academic experience for the Chapter.

Hydroshare – A Case Study Of The Application Of Modern Software Engineering To A Large Distributed Federally-Funded Scientific Software Development Project, Ray Idaszak, David G. Tarboton, Hong Yi, Laura Christopherson, Michael J. Stealey, Brian Miles, Pabitra Dash, Alva Couch, Calvin Spealman, Jeffery S. Horsburgh, Daniel P. Ames

Civil and Environmental Engineering Faculty Publications

HydroShare is an online collaborative system under development to support the open sharing of hydrologic data, analytical tools, and computer models. With HydroShare, scientists can easily discover, access, and analyze hydrologic data and thereby enhance the production and reproducibility of hydrologic scientific results. HydroShare also takes advantage of emerging social media functionality to enable users to enhance information about and collaboration around hydrologic data and models. HydroShare is being developed by an interdisciplinary collaborative team of domain scientists, university software developers, and professional software engineers from ten institutions located across the United States. While the combination of non–co-located, diverse stakeholders …

A Career In Innovation | College Of Engineering, Usu College Of Engineering

College of Engineering News

Oct. 10, 2016 – If you want to see Bruce Brothersen’s portfolio, just look up. His life’s work is built into the structures that make up our communities, spanning the schools, office buildings and aircraft hangars that keep the economy ticking.

The Layton, Utah, native came to USU for an undergraduate degree in the 1980s and quickly decided that engineering was a good fit.

Water Resources Systems Analysis Reading Assignments, Marcio Giacomoni

All ECSTATIC Materials

Read these articles:

https://ascelibrary.org/doi/10.1061/%28ASCE%290733-9496%282000%29126%3A3%28118%29

https://ascelibrary.org/doi/10.1061/%28ASCE%290733-9372%281990%29116%3A1%28182%29

https://ascelibrary.org/doi/10.1061/%28ASCE%290733-9496%281986%29112%3A3%28339%29

https://link.springer.com/article/10.1007/s11269-015-0970-6

https://ascelibrary.org/doi/10.1061/%28ASCE%290733-9496%282005%29131%3A6%28441%29

Answer the following questions:

1) Describe in your own words what is the problem that is being addressed? Why is it important?

2) What system is being modeled? Identify the system boundaries, processes, inputs and outputs.

3) How the system is being modeled? Identify the main state variables, parameters, initial conditions and boundary conditions.

4) What is the optimization method used to solve the problem. Describe the method.

5) What are the objective functions, constraints and decision variables?

6) What are the main conclusions and insights generated by the use of optimization? …