Civil and Environmental Engineering Commons^™

Flexural Behavior Of Portland Cement Based Composites Subjected To High Strain Rates, Edward Roland

Theses

This investigation studied the modulus of rupture and energy of rupture of mortar, concrete, and steel fiber reinforced mortar at various rates of flexural straining. The strengths of the composites were varied by changing the water cement ratios. Single point flexural loading tests were conducted on 4" x 4" x 20" specimens using a weight dropped from a height of 30" to produce the dynamic loading. Strain rates were varied between 0.1 and 1.9 per second. The inertial effects of acceleration of the specimen were taken into account.

These tests produced data that demonstrated slightly greater ratios of dynamic to …

Sorption Characteristics And Their Effects On Geotechnical Properties Of Illite, Gnanmoorthy Selvakumar

Theses

An experimental investigation of the sorption characteristics of phenol, chlorophenol and chlorobenzene on to illite and of the effect of sorption on the geotechnical properties of illite was performed. Various adsorption isotherms have been considered for the equilibrium adsorption study data. It was found that the Freundlich adsorption isotherm closely fits the experimental results. In addition, the results of desorption study indicated that the sorption process for these systems is not completely reversible.

The index properties of illite were found to be influenced by the sorption of contaminants, i.e., the Atterberg limits of illite increased in accordance with increases in …

Novel High Resolution Columns For Gas Chromatography, Douglas Kenneth Stout

Theses

A study was conducted to determine if BN would be a reliable solid phase or support for open tubular capillary columns and to develop a technique for the deposition of BN on the column's inner walls. The theoretical plate results for constructed precoated BN columns demonstrated that BN can be employed as solid stationary phase, but evinces low separation characteristics due to the nature of the drawing process. The development of a simple BN precoating process was tested on various diameter capillary columns and found to provide an excellent support for highly polar liquid stationary phases. Capillary columns with a …

Groundwater Contamination Studies At A Sanitary Landfill In New Jersey, Yau-Chorng Chien

Theses

Edgeboro Landfill, a site used for the disposal of municipal and industrial refuse, is one of the largest landfills in New Jersey. The landfill has been in operation since 1954, serving the solid waste disposal needs of local townships and a major portion of Middlessex and the surrounding counties. The landfill was not equipped with a liner and a leachate collection system at the time of start up. The leachate collection line around the landfill, on-site leachate treatment by three stabilization ponds and subsurface cut-off wall were provided to minimize the discharge of leachate into adjacent waters in 1979. Groundwater …

Failure Surface Of A Square And Rectangular Reinforced Concrete Members [Sic] Under Combined Biaxial Bending And Tension, Ravindra M. Khanapure

Theses

This thesis describes the development and use of three dimensional strength interaction diagrams of reinforced concrete sections for different loading conditions. It also gives a comprehensive overview of modes of failure surfaces and provides design aids for members subjected to biaxial bending and axial tension. This is the phenomena which is rather overlooked analytically and graphical predictions are made. The computer program provides a special tool for the analysis and fast interation of combination of loadings and moments.

The Degradation Of Trace Pollutants In Wastewater, Christine M. Cheng

Theses

The effect of different treatments on the degradation of chlorinated organic pollutants in wastewater has been studied. The model compound investigated was para-chlorophenol. The different treatments used were ozone, UV irradiation, ultrasound, air flow and pure oxygen.

It is concluded that ozone has the greatest effect, ozone-UV irradiation follows closely behind, and UV irradiation has much less of an effect in degrading the p-chlorophenol.

P-chlorophenol was found to have an immeasureably slow degradation rate when treated with air even at an elevated temperature of 55°C.

The oxygen, at room temperature, showed a degradation of p-chlorophenol which, although small, was much …

Steady-State Operation Of Bench-Scale Activated Sludge Process Using Phenol And 2-Chlorophenol As Substrates, Jeffrey Richard Caputi

Theses

Experiments were conducted to determine whether a continuous process similar to the common activated sludge process could be operated at a relative steady state with phenol and 2-chlorophenol as the sole carbon sources. After a number of unsuccessful trials, process conditions were developed which allowed for operation at a relative steady state with respect to the concentration of microorganisms in the reactor and the concentration of phenol and 2-chlorophenol in the effluent.

Phenol and 2-chlorophenol were removed at better than 99 percent efficiency on a continuous basis. The mixed liquor grown under the conditions of the experiment was highly filamentous …

High Temperature Reactions Of 1,2-Dichloroethane With Water Vapor In A Tubular Reactor, Charles E. Anderson

Theses

This study examines the reaction of l,2-dichloroethane with water vapor. The linear-flow method is utilized, assuming plug flow without axial diffusion. Normal operation is at atmospheric pressure and the reactor is a quartz tube in a thermal region 45 cm in length. Two reactor diameters of 0.4 cm and l.05 cm are used. Water and l,2-dichloroethane enter the system in liquid phase via syringe pumps. After vaporizing in heated tubing, they are combined with argon, the reactor carrier gas. The molar ratio of water to l,2-dichloroethane is 55:l and varied residence times are achieved by changing the argon flowrate. Reactor …

Experimental Study Of Rectangular Reinforced Concrete Members Under Combined Biaxial Bending And Tension, Naresh B. Patel

Theses

In practice it is a very common case to have a column subjected to combined effects of axial tension and biaxial bending moments and very few efforts are done to get good design approach for such special members.

So for this purpose, experiments were carried out on rectangular shapecolumns. Rectangular shaped columns were casted in homogeneous with brackets - one on each end and at connections haunches were provided to avoid the possible end failure. The overall shape of this configuration was "H" shape. Two hydraulic jacks were used; one on either side of the columns and thus column section …

Tests On Square Reinforced Concrete Members Under Combined Biaxial Bending And Tension, Bhadresh Shah

Theses

The research reported herein studies the ultimate strength behavior for square-shaped reinforced concrete short columns under combined biaxial bending and tension that is a common design problem. The present ACI building code (ACI 318-83) (1) and design hand book (2) do not offer an insight into the determination of strength and ductility behavior of biaxially loaded reinforced concrete columns. A design equation developed by Hsu (3,4,5 ) to study the ultimate strength behavior and failure surfaces for members under these combined action was used and the computed results were compared with the present analytical results and experimental results for square-shaped …

Investigation Of Water-Binding Properties Of Industrial Sludges Using Thermal Analysis As A Monitoring Tool, Ron Josephson

Theses

As part of a program to develop new and more cost-effective dewatering approaches for industrial hazardous wastes, sludges and synthetic "model" materials were analyzed by thermal methods in an attempt to comprehend their water-binding qualities and differentiate free and bound water. These thermal methods included Differential Thermal Analysis (DTA), Thermogravimetric Analysis (TG), and Differential Scanning Calorimetry (DSC). Industrial sludges and laboratory models were compared using both standard heating techniques and subambient cooling (to -60°C). This latter technique provides direct indication of the amount of free water. This information can be very useful in evaluating and improving dewatering techniques for industrial …

Systems Building Theory Application Within The Residential Housing Construction Market, Gary Alexander Newhard

Theses

The primary purpose of this report is to introduce the economical value in utilizing certain "systems building" applications. In this report I focus on integrated system methodologies that encourage residential building economy and submit such systems as a viable alternative to traditional labor intensive housing construction. The consumer market that could be particularly enhanced by these systems ranges from low income to middle income and the by-product would be classified as "affordable" housing.

This report focuses on the New Jersey real estate market and presents certain prefabricated housing systems as an economical means of meeting the large demand for residential …

Air Pollutant Emissions From Non-Vented Radiant Kerosene Heater, Anil Kumar Mishra

Theses

Gaseous emissions from non-vented kerosene heaters can generate and create significant indoor air concentrations of various gaseous pollutants. Indoor air concentrations resulting from operating a portable non-vented radiant type kerosene heater in three rooms of size 38.7, 58.1 and 137 M³ were studied. Studies in the environmental chamber having a size of 38.7 M³ under two sets of ventilation conditions showed elevated levels of CO₂, total hydrocarbons and CO. An emission rate model was used to estimate the strength of pollutant source, for total hydrocarbons, CO₂ and CO with data reported in terms of mass …

A Study Of Hazardous Wastes Generated In New Jersey With Regard To The Siting Of Waste Disposal Facilities In The State, Shreerang Narayan Dharasker

Theses

The effective treatment and disposal of hazardous wastes is one of the most urgent problems facing the State of New Jersey today. New Jersey is the most densely populated state and is a leader in industry. Nearly every major industry in the nation is represented by one or many production units all of which generate copious amounts of hazardous and toxic wastes each year. Although the state has the toughest rules and regulations on the management of hazardous waste, there are very few options exercised or facilities cited for the effective treatment and disposal of wastes within the state boundaries. …

Fracture Energy And Tensile Behavior Of Concrete, Wen-Jinn Chiou

Theses

Fracture behavior of concrete has been a subject of investigation for the past two decades. The need of understanding the complete tensile response of concrete is absolutely essential for theoretical modelling as well as design application of plain concrete structures.

In this study, attempts were made to investigate the validity of two important fracture parameters, namely, the fracture energy and the critical crack tip opening displacement. Three types of test specimen, dog- bone shaped tension specimen, notched beam and compact tension specimen, were investigated. These tests were conducted using the closed-loop MTS 810 strain-controlled testing system. For the uniaxial tension …

Biodegradation Of Mixed Phenolic Substrates, Prasad Gonnabathula

Theses

The biological degradation of phenol, with either 2-chlorophenol, 2,6-dichlorophenol, or nitrobenzene as cosubstrates was studied in aerated five - liter batch reactors using mixed liquor from the Passaic Valley Sewarage Commissioners wastewater treatment plant (Newark, NJ). The initial substrate concentrations were: 100 – 150 ppm phenol, 10 - 20 ppm 2-cp, 10 ppm 2,3 dcp, and 10 - 20 ppm nitrobenzene. The concentration vs. time data were fit to three kinetic models: zero-order, first-order, and Monod(assuming constant biomass). Most of the data were best fit by either the Monod or zero-order model. For all compounds tested, biodegradation was the primary …

Pozzolanic Admixtures In Concrete Mix, Ronghao Chen

Theses

Fly ash and condensed silica fume are two main mineral pozzolanic admixtures in portland cement concrete. The increasing use of the fly ash in concrete projects and concrete products during the past 3O years and condensed silica fume in several projects during the past 1O years indicates a greater acceptance of them as the mineral pozzolanic admixtures in concrete. Although the engineers are of some identical views in using these industrial byproducts in concrete projects, there are different views on how the behavior and utilization of fly ash con-crete and condensed silica fume concrete since the byproducts are not the …

Human Resources Planning In Construction Through Operations Research, Maria Pyla-Christodoulou

Theses

The purpose of this thesis is to examine different methods in the allocation of human resources in construction, using decision making through Operations Research. The methods described are divided into methods using mathematical models, and methods using heuristics. The mathematical models yield the optimum solution, while heuristics result in a satisfactory solution which can be improved by applying the optimization procedures described herein.

The human factor in construction is also examined, and methods of improving motivation among the construction workers are discussed.

Study Of The Effects Of Pumping Pressure On The Properties Of Fresh Concrete, Dinesh Vithal Kenkre

Theses

This thesis has a two-fold objective. One, to develop a suitable testing apparatus in the labaratory to simulate the effect of field pumping of concrete and two, to conduct some preliminary tests to investigate the feasibility of the testing apparatus.

Pumping of concrete has been practiced in the U.S.A. since 1930. The behaviour of concrete in a pipeline has not been studied in much detail while development in the pumping technology raced ahead of the research in this field. Previous studies done in this field have clearly indicated the need for a laboratory simulation of pumping process in order that …

The Effect Of Toxic Substances On The Index Properties Of Soils, Ronald Dicola

Theses

Contaminated soils were tested to determine if a relationship existed between their index properties and hydraulic conductivity. Atterberg Limit tests and Particle Size Analysis tests were performed on Woodbury, Raritan and Brunswick formation soils. The chemicals examined were Benzene, Phenol and Trichloroethylene (TCE). Tests were performed following the ASTM Standard Test Methods with only slight modification to accommodate the use of contaminated soils. Two different methods of soil contamination were used, one for chemical solutions and the other for pure chemicals.

Particle Size Analysis tests were performed both with and without dispersing agent. Hydrometer tests with dispersing agent resulted in …

Modelling Of Pile Load Tests In Weak Rock, Daniel Walter Caruso

Theses

The purpose of this thesis was to investigate the loss of load capacity of relaxed pile groups driven into weak bedrock. This was accomplished in the laboratory using a dynamic driving apparatus equipped with a static load testing system. The static load testing system applied loads hydraulically, and the load settlement behavior was monitored using an electronic load cell and a linear variable differential transducer (LVDT).

Tests were performed using 1" diameter steel pipe piles driven in a five pile group pattern at spacings of two diameters and four diameters. Piles were driven into a simulated rock mass consisting of …

Biodegradation Of Multiple Substrates In A Batch Reactor, Nilesh Naik

Theses

The biological degradation of multiple substrates was studied at room temperature in aerated 5-liter batch reactors using mixed liquor from the Passaic Valley Sewerage Commissioners wastewater treatment plant (Newark, New Jersey).

Two substrate mixtures were used (with initial concentration indicated in parenthesis): (1) phenol(100ppm) + nitrobenzene(10ppm) + 2,6-dichiorophenol(10ppm); (2) 2-chlorphenol(20ppm) + nitrobenzene(10ppm) + 2,6-dichlorphenol(10ppm). From concentration versus time data, kinetic rate constants for zero-order, first-order, and Monod models were determined. Most of the data were best fit by either the Monod or zero-order model. For all compounds tested biodegradation was the primary removal mechanism, and in many cases the rate …

Saturated Hydraulic Conductivity Of Brunswick Soil With Aqueous Benzene Solution, Thomas R. Pisciotta

Theses

Tests measuring saturated hydraulic conductivity and dispersivity were conducted on Brunswick soil using an aqueous solution of benzene. The tests were performed using a flexible wall permeameter which was modified to allow extraction of effluent samples immediately upon exit of the test specimen. Influent and effluent samples were analyzed with a gas chromatograph in order to quantify dispersion and sorption in the specimen.

The test was performed using a confining pressure of 70 psi. and a hydraulic gradient of 100.3. Using a sample statically compacted to 99.2% of the Modified Proctor maximum density and tap water as a permeant, stable …

Similitude Analysis Of Model Experiments Of Piles Driven To Rock, George Nicou Georghoudes

Theses

This thesis investigates the similitude requirements for the Dynamic Pile Driving Apparatus in the New Jersey Institute of Technology Laboratory. The apparatus is being used to perform model tests to study bearing stratum fracturing caused by driving pile groups to weak rock.

Two approaches were used to establish similitude between the model and actual field conditions. The first approach utilizes dimensional analysis to develop a relationship between the energy delivered to the rock mass by the pile and the unit length. The second approach proposes a procedure to establish an empirical relationship between the threshold energy to fracture the rock …

Use Of Clay As A Landfill Liner, Mayur B. Desai

Theses

The purpose of this thesis is to study the factors affecting efficient functioning of clay material for containment of landfill materials. The study of liner-leacheate interaction is done from the consolidation and vane shear tests on various clays having different activities, and chemicals that are typically found in a municipal solid waste leachate and a leachate collected from an active landfill.

An effort was made to study the use of Atterberg limits to predict the suitability of a clay as a landfill liner for a given waste environment. The study indicates that there is a decrease in permeability of bentonite …

Effects Of Adhesion On The Active Pressure Exerted On A Retaining Wall, Thomas G. Gallagher

Theses

This paper investigated the effect of adhesion on the active pressure behind a retaining wall. No equation existed to solve for the active pressure for a sloped backfill that also takes into consideration cohesive and adhesive forces on a failure wedge. The trial—wedge solution(Culmann method) considers these parameters, but since it is a trial and error method it takes up too much time to solve. A shorter solution is desirable. An equation for the active pressure in terms of ρ(angle between horizontal and failure plane) was derived. A closed form solution for earth pressure was developed by setting the derivative …

Computer Application Of Project Planning And Scheduling With Cpm, Mohamed Tarek Abdel-Aziz

Theses

Scheduling is one of the most important tools for project management and control, and the CPM is one of the techniques used in project scheduling.

The primary objective of this thesis is to develop a CPM computer package using a microcomputer. The package is constituted in Basic (Applesoft Basic) for use on Apple II Plus, IIe or IIc.

The package is intended to be available to users without sufficient knowledge about computer. And it consists of two computer programs. The first computer program is the CPM-I which schedules project activities with unlimited resources. The second computer program is the CPM-II …

Determination Of Trace Quantities Of Selenium And Arsenic In Canned Tuna Fish Using Electroanalytical Techniques, Ann Marie Higham

Theses

Toxic metals are present in the environment and are known to be present in food. Selenium, which is considered an essential micronutrient, is recognized as a toxic metal at slightly higher concentrations. Arsenic is also recognized as a toxic metal. Selenium and Arsenic tend to accumulate in food, specifically fish and seafood.

Fifteen brands and types of tuna fish were analyzed for selenium using differential pulse cathodic stripping voltammetry. The cans with the high and low concentrations of selenium were analyzed for arsenic using differential pulse polarography. Three samples with three percent recoveries and a blank were analyzed for each …

A Study Of Parameters Indicating Microbial Activity In Mixed Aerobic Cultures, William Smith

Theses

Mixed liquor suspended solids (MLSS), oxygen uptake rate (OUR) and general dehydrogenase activity, as expressed by the reduction of the electron-acceptor Dye 3-(4',5'-dimethylthiazol-2-yl)-2, 4-diphenyltetra-zolium bromide (MTT), were compared for their ability to measure microbial activity in mixed aerobic cultures. A fourth parameter, specific enzyme activity, was dropped from consideration because of the difficulty of developing a satisfactory experimental technique. Measurement of the parameters was applied to the biodegradation of phenol and o-chlorophenol by activated sludge from a municipal sewage treatment plant, and by two commercially available bacterial preparations.

MLSS, although the most commonly used of the three parameters tested, is …

Model Experiment Of Rock Fracturing Caused By Driving Piles, Dai-Heyng Lee

Theses

The geotechical construction problem of rock fracturing caused by pile driving is investigated using a laboratory model. One inch diameter closed bottom steel pipes were driven into a simulated rock mass consisting of masonry bricks having an average compressive strength 3,200 psi. Both single pile and five pile model groups were tested. The single pile tests indicated that a threshold of penetration behavior occurred at a theorical hammer energy of 100 ft-lb and this was used for the group tests. Penetration rates were measured using an optical level.

Piles in the five pile model group were initially driven to a …