Civil and Environmental Engineering Commons^™

Critical Buckling And Post-Buckling Behavior Of Thin-Walled Liners Encased By Underground Pipelines In Saturated Soils, Zhaochao Li

Doctoral Dissertations

"This study aims to investigate the structural stability of thin-walled liners encased in functionally-obsolete underground pipelines in saturated soil under external hydrostatic pressure, a concentrated load, temperature change or their combination, and develop a simplified circular arch model of thin-walled liners when not constrained by the pipelines. The friction and adhesion on the interface between a liner and its constraining surface (pipeline or grouting), and the pressure gradient on deeply-buried pipelines are neglected. The critical buckling load of elastic liners is analytically derived under a plane strain condition using the principle of minimum potential energy. The analytical solution is either …

Atomic Layer Deposition Prepared Nanostructured Materials For Various Catalytic Reactions, Xiaofeng Wang

Doctoral Dissertations

"Atomic layer deposition (ALD) has been widely used for thin film coating and metal nanoparticles (NPs) preparation. In this report, the applications of ALD prepared nanostructured materials in catalysis were examined.

Highly dispersed Pt monometallic catalysts with different substrates and multi-walled carbon nanotubes (MWCNTs) supported Pt-Co bimetallic catalysts were synthesized by ALD for selective hydrogenation of α, β-unsaturated aldehydes to unsaturated alcohols (UA). Pt/MWCNTs showed the highest selectivity of UA in selective hydrogenation of citral, as compared to Pt/SiO₂, Pt/ALD-Al₂O₃, and Pt/γ-Al₂O₃. After adding Co, the highest selectivity was achieved …

Long-Term Behavior Of Fiber Reinforced Polymer (Frp) Confined Concrete Cylinders Subjected To Severe Weather And Seawater Solution Conditions, Song Wang

Doctoral Dissertations

"This study presents an experimental investigation on durability of fiber-reinforced polymer (FRP) confined concrete cylinders subjected to various environmental conditions. Two types of cylinders were tested in this experiment: concrete-filled FRP tube (CFFT) and hollow-core FRP-concrete-steel (HC-FCS), with FRP tubes having two different constitutive resin components: polyester and epoxy. The specimens were subjected to three different environmental conditions: combined freeze/thaw, wet/dry and heating/cooling cycles with options of continuous water immersion and sustained axial load in an environmental chamber, UV exposure in an UV chamber, and seawater immersion in water tanks with sustained axial load. Mechanical and material characterization tests were …

Agenda For The Fifth Meeting Of The Forum On Soil Dynamics, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Membership Of Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Minutes Of The Fifth Meeting Of The Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Drone-Enabled Remote Sensing For Transportation Infrastructure Assessment, Colin Brooks

INSPIRE Archived Webinars

Unmanned aerial systems (UAS or “drones”) are a rapidly developing technology that can help meet the needs of transportation agencies for reliable, repeatable data that can save money and increase safety for the data collection process. By taking advantage of flexible platforms that can deploy a variety of sensors, transportation agencies and their information suppliers can help meet these data needs for operations, asset management, and other areas. Location-specific data on infrastructure condition and distresses can help with improved management of assets.

In this presentation, recent applied research led by a Michigan Technological University team is reviewed, with a focus …

Metabolism And Photolysis Of 2,4-Dinitroanisole In Arabidopsis, Hunter W. Schroer, Xueshu Li, Hans Joachim Lehmler, Craig L. Just

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

New insensitive munitions explosives, including 2,4-dinitroanisole (DNAN), are replacing traditional explosive compounds to protect soldiers and simplify transport logistics. Despite the occupational safety benefits of these new explosives, feasible strategies for cleaning up DNAN from soil and water have not been developed. Here, we evaluate the metabolism of DNAN by the model plant Arabidopsis to determine whether phytoremediation can be used to clean up contaminated sites. Furthermore, we evaluate the role of photodegradation of DNAN and its plant metabolites within Arabidopsis leaves to determine the potential impact of photolysis on the phytoremediation of contaminants. When exposed to DNAN for three …

Amplification Of Earthquake Ground Motions In Washington, Dc, And Implications For Hazard Assessments In Central And Eastern North America, Thomas L. Pratt, J. Wright Horton Jr., Jessica Munoz, Susan E. Hough, Martin C. Chapman, C. Guney Olgun

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The extent of damage in Washington, DC, from the 2011 M_W 5.8 Mineral, VA, earthquake was surprising for an epicenter 130 km away; U.S. Geological Survey “Did-You-Feel-It” reports suggest that Atlantic Coastal Plain and other unconsolidated sediments amplified ground motions in the city. We measure this amplification relative to bedrock sites using earthquake signals recorded on a temporary seismometer array. The spectral ratios show strong amplification in the 0.7 to 4 Hz frequency range for sites on sediments. This range overlaps with resonant frequencies of buildings in the city as inferred from their heights, suggesting amplification at frequencies to …

A Humidity-Controlled Fast Integrated Mobility Spectrometer (Hfims) For Rapid Measurements Of Particle Hygroscopic Growth, Tamara Pinterich, Steven R. Spielman, Yang Wang, Susanne V. Hering, Jian Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

We present a humidity-controlled fast integrated mobility spectrometer (HFIMS) for rapid particle hygroscopicity measurements. The HFIMS consists of a differential mobility analyzer (DMA), a relative humidity (RH) control unit and a water-based FIMS (WFIMS) coupled in series. The WFIMS (Pinterich et al., 2017) combines the fast integrated mobility spectrometer (Kulkarni and Wang, 2006a, b) with laminar flow water condensation methodologies (Hering and Stolzenburg, 2005; Spielman et al., 2017). Inside the WFIMS, particles of different electrical mobilities are spatially separated in an electric field, condensationally enlarged and imaged to provide 1 Hz measurements of size distribution spanning a factor of ∼3 …

Dynamic Mechanical Properties And Microstructure Of Graphene Oxide Nanosheets Reinforced Cement Composites, Wujian Long, Jingjie Wei, Hongyan Ma, Feng Xing

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents an experimental investigation on the effect of uniformly dispersed graphene oxide (GO) nanosheets on dynamic mechanical properties of cement based composites prepared with recycled fine aggregate (RFA). Three different amounts of GO, 0.05%, 0.10%, and 0.20% in mass of cement, were used in the experiments. The visual inspections of GO nanosheets were also carried out after ultrasonication by transmission electron microscope (TEM) atomic force microscope (AFM), and Raman to characterize the dispersion effect of graphite oxide. Dynamic mechanical analyzer test showed that the maximum increased amount of loss factor and storage modulus, energy absorption was 125%, 53%, …

Rheological Properties Considering The Effect Of Aggregates On Concrete Slump Flow, Tae Yong Shin, Jae Hong Kim, Seong Ho Han

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Rheology of concrete allows us to understand the flow behavior of concrete and further extend the quantitative evaluation of its construction performance. The use of a concrete rheometer is promising for the purpose but sometimes limited high associated cost and procedure complexity. This study proposes a simulation-based model that correlates the slump flow test results to a concrete's rheological properties, allowing quantitative evaluation through this simple method. The proposed model is based on single-fluid simulation using the volume-of-fluid method, with an extension to accommodate the partial segregation of coarse aggregates. Either the channel flow or the L-shaped panel filling of …

How We Compute N Matters To Estimates Of Mixing In Stratified Flows, Robert S. Arthur, Subhas K. Venayagamoorthy, Jeffrey R. Koseff, Oliver B. Fringer

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Most commonly used models for turbulent mixing in the ocean rely on a background stratification against which turbulence must work to stir the fluid. While this background stratification is typically well defined in idealized numerical models, it is more difficult to capture in observations. Here, a potential discrepancy in ocean mixing estimates due to the chosen calculation of the background stratification is explored using direct numerical simulation data of breaking internal waves on slopes. Two different methods for computing the buoyancy frequency, one based on a three-dimensionally sorted density field (often used in numerical models) and the other based on …

On The Propagation Of Gravity Currents Over And Through A Submerged Array Of Circular Cylinders, Jian Zhou, Claudia Cenedese, Tim Williams, Megan Ball, Subhas K. Venayagamoorthy, Roger I. Nokes

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The propagation of full-depth lock-exchange bottom gravity currents past a submerged array of circular cylinders is investigated using laboratory experiments and large eddy simulations. Firstly, to investigate the front velocity of gravity currents across the whole range of array density (i.e. the volume fraction of solids), the array is densified from a flatbed towards a solid slab under a particular submergence ratio, where is the flow depth and is the array height. The time-averaged front velocity in the slumping phase of the gravity current is found to first decrease and then increase with increasing. Next, a new geometrical framework consisting …

A Modeling Enterprise For Chemistry Of Indoor Environments (Cie), G. C. Morrison, N. Carslaw, M. S. Waring

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Time-Dependent Prestress Loss Behavior Of Girders In Missouri Bridge A7957 Compared With A U.S. Data Set Of High-Performance Concrete Bridge Girders, Hayder H. Alghazali, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, six precast, prestressed concrete girders were constructed and instrumented to measure prestress losses of bridge A7957 in Missouri. The concrete mixture for the bridge was designed with varying mechanical and rheological properties. High-strength concrete, high-strength self-consolidating concrete, and normal-strength self-consolidating concrete were used to construct the bridge girders. Vibrating wire strain gauges with integrated thermistors were embedded through the girders' cross sections to measure strains and temperatures. The measured short- and long-term prestress losses were compared with those obtained using different empirical models, specified in the AASHTO LRFD Bridge Design Specifications and in the PCI Design Handbook: …

Hollow-Core Frp-Concrete-Steel Bridge Columns Under Torsional Loading, Sujith Anumolu, Omar I. Abdelkarim, Mohanad M. Abdulazeez, Ahmed Gheni, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the behavior of hollow-core fiber-reinforced polymer-concrete-steel (HC-FCS) columns under cyclic torsional loading combined with constant axial load. The HC-FCS consists of an outer fiber-reinforced polymer (FRP) tube and an inner steel tube, with a concrete shell sandwiched between the two tubes. The FRP tube was stopped at the surface of the footing, and provided confinement to the concrete shell from the outer direction. The steel tube was embedded into the footing to a length of 1.8 times the diameter of the steel tube. The longitudinal and transversal reinforcements of the column were provided by the steel tube …

Seismic Performance Of Hollow-Core Composite Columns Under Cyclic Loading, Mohanad M. Abdulazeez, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper experimentally investigates the seismic behavior of a large-scale, hollow-core, fiber-reinforced, polymerconcrete- steel HC-FCS column under cyclic loading. The typical precast HC-FCS member consists of a concrete wall sandwiched between an outer fiber-reinforced polymer (FRP) tube and an inner steel tube. The FRP tube provides continuous confinement for the concrete wall, along the height of the column. The column is inserted into the footing and temporarily supported; then, the footing is cast in place around the column. The seismic performance of the precast HC-FCS columns was assessed and compared with previous experimental work. The compared column had the same …

Dermal Uptake Of Benzophenone-3 From Clothing, Glenn C. Morrison, Gabriel Bekö, Charles J. Weschler, Tobias Schripp, Tunga Salthammer, Jonathan Hill, Anna Maria Andersson, Jørn Toftum, Geo Clausen, Hanne Frederiksen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Benzophenone-3 (also known as BP-3 or oxybenzone) is added to sunscreens, plastics, and some coatings to filter UV radiation. The suspected endocrine disruptor BP-3 has been detected in the air and settled dust of homes and is expected to redistribute from its original sources to other indoor compartments, including clothing. Given its physical and chemical properties, we hypothesized that dermal uptake from clothing could contribute to the body burden of this compound. First, cotton shirts were exposed to air at an elevated concentration of BP-3 for 32 days; the final air concentration was 4.4 μg/m3. Next, three participants wore the …

The Bridge Newsletter Winter 2017, Missouri University Of Science And Technology

The Bridge Newsletter

-Hands-on experience in concrete materials research and construction practices
-Making ACML progress
-Taos bridge project

Lab-On-Sensor For Structural Behavior Monitoring: Theory And Applications, Genda Chen

INSPIRE Archived Webinars

There are over 600,000 bridges in the U.S. National Bridge Inventory (NBI). Nearly 50% of them rapidly approach their design life and deteriorate at an alarming rate, particularly under an increasing volume of overweight trucks. Visual inspection as the current practice in bridge management is labor intensive and subjective, resulting in inconsistent and less reliable element ratings. Lab-on-sensor technologies can provide supplemental mission-critical data to the visual inspection for both qualitative and quantitative evaluations of structural conditions, and thus critical decision-making of cost-effective strategies in bridge preservation.

In this presentation, the design and operation characteristics of highway bridges are first …

Measuring Rheological Properties Of Cement Pastes: Most Common Techniques, Procedures And Challenges, Dimitri Feys, Rolands Cepuritis, Stefan Jacobsen, Karel Lesage, Egor Secrieru, Ammar Yahia

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Science of Rheology is Increasingly Used to Describe the Properties of Fresh Cement Paste. Compared to Standard Workability Tests, Rheological Properties Allow for More Fundamental Investigation, More Precise Phenomenological Description of Flow Properties and Serve as Input for Numerical Simulations. Standard Commercially Available Rheometers Are Typically Used to Perform Those Measurements. However, the Results of the Measurement Depend on the Geometry, Testing Procedure and a Number of Potential Artefacts. This Technical Letter Describes the Most Common Techniques and Procedures Used to Assess the Rheological Properties of Cement Paste, as Well as Challenges during Measurements and Actions to Counter These …

Cyclic Compression Behavior Of Concrete-Filled Hybrid Large Rupture Strain Frp Tube, Monika Nain, Mohanad M. Abdulazeez, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper experimentally investigates the behavior of concrete-filled-fiber-reinforced polymer (FRP) cylinders under cyclic axial compression. The FRP used in this study were either large rupture strain FRP (LRS-FRP) or hybrid LRS-FRP and conventional glass FRP (GFRP). LRS-FRP are manufactured out of polyethylene naphthalate (PEN) and polyethylene terephthalate (PET) obtained from recycled plastics. Hence, they are much cheaper and environment-friendly than conventional GFRP or carbon FRP (CFRP). LRS-FRPs has high tensile rupture strain (usually greater than 5%) compared to 1-2% for GFRP and CFRP. This study presents the results of 4 specimens with different confinement ratios to investigate the behavior of …

Torsional Behavior Of Hollow-Core Frp-Concrete-Steel Bridge Columns, Sujith Anumolu, Omar I. Abdelkarim, Mohanad M. Abdulazeez, Ahmed Gheni, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the behavior of hollow-core fiber reinforced polymer-concrete-steel (HC-FCS) column under pure torsion loading with constant axial load. The HCFCS consists of outer FRP tube and inner steel tube with concrete shell sandwiched between the two tubes. The FRP tube was stopped at the surface of the footing and provided confinement to the concrete shell from outer direction. The steel tube was embedded into the footing to a length of 1.8 times to the diameter of the steel tube. The longitudinal and transversal reinforcements of the column were provided by the steel tube only. A large-scale HC-FCS column …

Nonlinear Analysis Of Hollow-Core Composite Building Columns, Mohanad M. Abdulazeez, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper numerically investigates the behavior of hollow-core fiber-reinforced polymer-concrete-steel (HC-FCS) building columns under combined axial compression and flexural loadings. The HC-FCS column for buildings consists of an outer circular fiber-reinforced polymer (FRP) tube, an inner square steel tube, and a concrete wall between them. A three-dimensional numerical model has been developed using LS_DYNA software for modeling of large scale HC-FCS columns. The nonlinear FE models were designed and validated against experimental results gathered from HC-FCS columns tested under cyclic lateral loading. The FE results were in decent agreement with the experimental backbone curves. These models subsequently were used to …

Impact Of Surface Ozone Interactions On Indoor Air Chemistry: A Modeling Study, M. Kruza, A. C. Lewis, G. C. Morrison, N. Carslaw

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

An INdoor air Detailed Chemical Model was developed to investigate the impact of ozone reactions with indoor surfaces (including occupants), on indoor air chemistry in simulated apartments subject to ambient air pollution. The results are consistent with experimental studies showing that approximately 80% of ozone indoors is lost through deposition to surfaces. The human body removes ozone most effectively from indoor air per square meter of surface, but the most significant surfaces for C6-C10 aldehyde formation are soft furniture and painted walls owing to their large internal surfaces. Mixing ratios of between 8 and 11 ppb of C6-C10 aldehydes are …

Identifying Corrosion Zones In Coastal Regions For Metal Pipes -- A Gis Approach, Sanjay Tewari, Francis Manning

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Transportation agencies often allow metal pipes as an option for cross drains under/along roads and highways. Metal culverts can corrode over time at various rates based on their environmental conditions (e.g., corrosive nature of coastal soils, high water table and saltwater intrusion). This paper focuses on applying readily available soil data such as spatial distribution of soil types and soil characteristics (e.g., pH and conductivity) towards creating a geospatial information system (GIS) based approach to identifying corrosion zones in the coastal regions. A combination of data, obtained from field surveys provided by the Louisiana Transportation Research Center and Web Soil …

Program Progress Performance Report #1, Missouri University Of Science And Technology. Inspire - University Transportation Center

Semi-Annual Progress Reports

No abstract provided.

Reducing Costs While Maintaining Learning Outcomes Using Blended, Flipped, And Mastery Pedagogy To Teach Introduction To Environmental Engineering, Daniel B. Oerther

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

As part of a cost-savings initiative, an existing course of 'introduction to environmental engineering' offered using a 'traditional' format of didactic class meetings supplemented with hands-on laboratory sessions, was changed significantly. The 'modified' format uses 'blended', 'flipped', and 'mastery' approaches to teach "2601: Fundamentals of Environmental Engineering" to approximately 60 sophomores pursuing baccalaureate degrees in environmental, civil, or architectural engineering, each semester. This paper presents a summary of the results from eight course offerings over a period of four years to more than 450 total students. Assessments included student grades; open-ended invitations for anonymous feedback at the end of each …

Corrosion Map For Metal Pipes In Coastal Louisiana, Sanjay Tewari

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Transportation agencies often allow metal pipes as an option for cross drains under/along roads and highways. Metal culverts can corrode over time at various rates based on their environmental conditions (e.g., corrosive nature of coastal soils, high water table, and saltwater intrusion).

This project was focused on applying available soil data, such as spatial distribution of soil types and soil characteristics (e.g., pH and conductivity), towards creating a Geographic Information System (GIS) based map to identify corrosion zones in coastal Louisiana. The effect of the soil characteristics (pH and conductivity) was incorporated in to the published corrosion models for calculating …