Civil and Environmental Engineering Commons^™

Interior Node Projection Techniques In Sweeping Algorithms, Michael Andrew Scott

Theses and Dissertations

The enhancement of node projection techniques in sweeping is the subject of this thesis. Sweeping is a method used to produce all-hexahedral finite element meshes on certain classes of geometry. The placement of nodes in the interior of the geometry during the sweeping process remains a difficult problem. This thesis presents advancements in this area which improve the speed of the algorithm and the resulting element quality. A comparison of existing projection methods was performed. The existing Faceted projection sweeping method was extended to be applicable to more general classes of sweepable geometry. This comparison and extension of node projection …

A Gasless Method Of Spraying Thermoplastic Resin, Dan T. Rogers

Theses and Dissertations

This spraying method for thermoplastic resins is a new manufacturing process for applying thermoplastics to a mold or surface in an efficient way that has the potential of reducing cycle time. Spraying thermoplastic resins is similar to spraying other polymers, such as paint, with the differences being higher pressure and temperature. This method uses an injection molding machine with a modified nozzle to spray the plastic material. In this study, temperature, pressure, and nozzle size were factors that influenced the success of this spraying method. The method of spraying in this study proved spraying without a gas is possible, a …

Effects Of Reclaimed Asphalt Pavement On Mechanical Properties Of Base Materials, Dane A. Cooley

Theses and Dissertations

Reuse of reclaimed asphalt pavement (RAP) in the full-depth recycling (FDR) process is a cost-effective and environmentally responsible method of asphalt pavement reconstruction. Although FDR has been used for several years in some locations, the effect of RAP on the mechanical properties of recycled base materials has not been well documented. The purpose of this research was to investigate the influence of RAP on the mechanical properties of recycled base materials typical of northern Utah. Two sources of RAP, two sources of base, and RAP contents of 0, 25, 50, 75, and 100 percent were utilized in a full-factorial experimental …

Development Of Commercial Applications For Recycled Plastics Using Finite Element Analysis, Nanjunda Narasimhamurthy

Theses and Dissertations

This thesis investigates the suitability of thermo-kinetically recycled plastics for use in commercial product applications using finite element analysis and statistics. Different recycled material blends were tested and evaluated for their use in commercial product applications. There are six different blends of thermo-kinetically recycled plastics used for testing and CATIA is used for finite element analysis. The different types of thermo-kinetically recycled plastics blends are: pop bottles made of PolyethyleneTeraphthalate (PET), milk jugs made of High-Density Polyethylene (HDPE), Vinyl seats made of Poly Vinyl Chloride (PVC) and small amount of Polypropylene (PP) and Urethane, electronic scrap made of engineering resins …

An Automated Three-Dimensional Unstructured Mesh Generation Algorithm For Groundwater Modeling, James Edward Greer

Theses and Dissertations

This thesis describes a new method to create three-dimensional finite element meshes using the horizons to mesh algorithm. The algorithm uses available geologic data and user-defined inputs to guide the mesh generation process. This new approach allows for material layer pinch outs and many different layer refinement options to create well-formed elements that better represent hydrogeologic formations. Two case studies are presented that demonstrate the application of the algorithm's options and capabilities. A graphical interface for the algorithm was developed in the Groundwater Modeling System.

Refining And Expanding The Feature Stamping Process, Russell N. Emery

Theses and Dissertations

The accuracy of numerical models analyzing hydrologic and hydraulic processes depends largely on how well the input terrain data represents the earth's surface. Modelers obtain terrain data for a study area by performing surveys or by gathering historical survey data. If a modeler desires to create a predictive model to simulate the addition of man-made features such as channels, embankments and pits, he must modify the terrain data to include these features. Doing this by hand is tedious and time consuming. In 2001 Christensen implemented a tool in the Surface-water Modeling System (SMS) software package for integrating man-made geometric features …

Characterization Of Recycled Concrete For Use As Pavement Base Material, Brandon J. Blankenagel

Theses and Dissertations

The use of recycled concrete material (RCM) as pavement base material is a promising but unproven technique for road rehabilitation and construction. A telephone survey conducted to investigate the state of the practice concerning RCM usage in Utah County revealed that RCM is infrequently used in this application due primarily to a lack of practical knowledge about the engineering properties of the material. Therefore, this research was aimed at evaluating the physical properties, strength parameters, and durability characteristics of both demolition and haul-back sources of RCM available in Utah County for use as pavement base material. The study included extensive …

Assessing Construction Management Higher Education Strategies: Increased Demand, Limited Resources, And Over-Enrollment, Kristen Lea Wynn

Theses and Dissertations

The purpose of this research was to see how Baccalaureate Construction Management Programs accredited by the American Council for Construction Education (ACCE) were managing increased enrollments within their programs. The review of literature identified related topics, comparable studies, and relevant issues surrounding over-enrollment. Forty-nine of the 53 accredited ACCE programs responded to the survey instrument. Over two-thirds of the respondents stated that they were either approaching, or were at the limits of enrollment capacities. Most of the respondents listed limited enrollment, the use of adjunct faculty, and funding from industry as leading strategies for managing or obtaining resources. Because CM …

Development Of A Frost Heave Test Apparatus, Russell David Lay

Theses and Dissertations

Frost heave damage to roadways costs millions of dollars every year. The need for an improved understanding of the fundamental mechanisms associated with frost heave and methods for efficiently improving frost-susceptible materials prompted the Department of Civil and Environmental Engineering at Brigham Young University (BYU) to undertake a project to design, construct, and verify the functionality of a new frost heave testing apparatus. Frost heave research has been carried out for more than 75 years. The equipment used to conduct this testing has advanced in accuracy and utility over the years. To establish a background in past and current frost …

Full-Scale Lateral Load Test Of A 3x5 Pile Group In Sand, James Matthew Walsh

Theses and Dissertations

Although it is well established that spacing of piles within a pile group influences the lateral load resistance of that group, additional research is needed to better understand trends for large pile groups (greater than three rows) and for groups in sand. A 15-pile group in a 3x5 configuration situated in sand was laterally loaded and data were collected to derive p-multipliers. A single pile separate from the 15-pile group was loaded for comparison. Results were compared to those of a similar test in clays. The load resisted by the single pile was greater than the average load resisted by …

Annual Exceedance Probability Analysis, Masako Amai Gardner

Theses and Dissertations

Annual Exceedance Probability (AEP) is the method used by U.S. Army Corps of Engineers (USACE) to determine the probability of flooding caused by the failure of a levee or other flood control structure. This method shows the probability of flooding only at one particular location at a time. In order to overcome the limitation of AEP, a new method of studying flood probability, called an AEP map, was presented. By using hydrologic and hydraulic modeling software, an AEP map can be created to determine and visualize the spatial distribution of the probability of flooding. An AEP map represents a continuous …

Establishing Public Confidence In The Viability Of Fingerprint Biometric Technology, Nathan Alan Green

Theses and Dissertations

The most common personal authentication techniques used for identity management employ a secret PIN or password that must be remembered. The challenge, for a given user, is that a multitude of such codes must be recalled over the course of the day for transactions involving distinct computer applications. Password mania prevails. Fingerprint biometric technology is an ideal alternate solution to this password recall problem. In spite of their availability for nearly thirty years, fingerprint biometric systems still remain uncommon in public sectors of industry such as education, government, and technology. Technology has improved sufficiently that false acceptance and rejection rates …

Integrating Value Stream Mapping And Simulation, Michelle E. Scullin

Theses and Dissertations

An important principle in Lean manufacturing, value stream mapping (VSM) can be helpful in understanding how process flow and information flow affect each other. A VSM is a static picture of a process that allows the user to see where value is added into the value stream. Simulation is used to evaluate the behavioral issues of processes. In a manufacturing realm this means simulation shows how each operation affects other operations so determinations can be made about where bottlenecks or other problems exist in the process. Theoretically, the integration of VSM and Simulation can aide in process improvement by showing …

Development Of A User Cost Estimation Procedure For Work Zones., Michael Roy Adams

Theses and Dissertations

Work zones associated with highway construction projects create localized bottlenecks where the average traffic speed is reduced and queues are formed, thus causing increased costs as a result of the additional time and fuel needed to traverse the work zone. These user costs can be estimated and applied as a form of incentive to the contractor to complete the work sooner, thus allowing traffic to return to the free-flow speed. Methods to determine user costs are explored through a literature search, questionnaire survey, and interviews with employees of the Utah Department of Transportation (UDOT). Based on the research and interviews, …

Condition Analysis Of Concrete Bridge Decks In Utah, Robert S. Tuttle

Theses and Dissertations

Concrete bridge decks in Utah are experiencing observable deterioration due primarily to freeze-thaw cycles and the routine application of deicing salts during winter maintenance activities. Given the need for increasingly cost-effective strategies for bridge deck maintenance, rehabilitation, and replacement (MR&R), the Utah Department of Transportation (UDOT) initiated this research to ultimately develop a protocol offering guidance as to whether deteriorated bridge decks should be rehabilitated or replaced. While threshold values for various non-destructive condition assessment methods were proposed in earlier UDOT research, this work focused on implementing the recommended test criteria. Twelve bridges were identified by UDOT engineers for inclusion …

Performance Of Concrete Bridge Deck Surface Treatments, Tyler S. Nelsen

Theses and Dissertations

The purpose of this research was to identify the types of surface treatments available for use on concrete bridge decks and to determine which materials are most capable of providing long-term protection from contamination by chloride ions. The products addressed in this report primarily include urethanes, silicon-based sealers, and epoxies. An extensive literature review was conducted to document common overlay distresses, performance histories, and properties of specific surface treatment products currently available in the industry. In addition, three reports summarizing in-house experiments performed by the Utah Department of Transportation between 1995 and 2003 regarding various types of surface treatments were …

Developing A Gis And Hydrological Modeling Approach For Sustainable Water Resources Management In The West Bank -- Palestine, Walid Wajeeh Sabbah

Theses and Dissertations

This research deals with setting up a GIS and hydrological modeling based approach for sustainable water resources management in the West Bank of Palestine. This water sustainability approach took into consideration the water balance, the social, the economic, the demographic, the environmental, and the institutional components in order to enhance and promote the sustainable development in Palestine, both on the short and long runs. To evaluate the water balance component, a methodology was introduced to create the Water Sustainability Map (WSM). Since the groundwater is currently the only accessible water source by the Palestinians, the WSM is represented by the …

Analytical Modeling Of Wood-Frame Shear Walls And Diaphragms, Johnn Paul Judd

Theses and Dissertations

Analytical models of wood-frame shear walls and diaphragms for use in monotonic, quasi-static (cyclic), and dynamic analyses are developed in this thesis. A new analytical model is developed to accurately represent connections between sheathing panels and wood framing members (sheathing-to-framing connections) in structural analysis computer programs. This new model represents sheathing–to–framing connections using an oriented pair of nonlinear springs. Unlike previous models, the new analytical model for sheathing-to-framing connections is suitable for both monotonic, cyclic, or dynamic analyses. Moreover, the new model does not need to be scaled or adjusted. The new analytical model may be implemented in a general …

Size Function Based Mesh Relaxation, John David Howlett

Theses and Dissertations

This thesis addresses the problem of relaxing a finite element mesh to more closely match a size function. The main contributions include new methods for performing size function based mesh relaxation, as well as an algorithm for measuring the performance of size function based mesh relaxation methods.

Determination Of Wall Thickness And Height When Cutting Various Materials With Wire Electric Discharge Machining Processes, Sangseop Kim

Theses and Dissertations

This thesis looks at the capabilities of cutting thin webs on Wire EDM machines that are difficult or impossible to machine using conventional methods. Covered is an investigation of how different material and web thickness affect the capability of machining thin-walled parts.

Five different metals are used for the test; Aluminum 6061 T6, Yellow Brass SS360, 420 Stainless Steel, D2 unheat-treated tool steel 25-30 RC, and D2 heat-treated tool steel 60-65 RC. The small parts were cut to a 6mm (0.2362 inch) height with six different wall thicknesses: 0.30mm (0.0118 inch), 0.25mm (0.0098 inch), 0.20mm (0.0078 inch), 0.15mm (0.0059 inch), …

A Tool Wear Comparative Study In Turning Versus Computer Simulation In 1018 Steel, Woodrow D. Miner

Theses and Dissertations

The material removal process uses cutting tools in order to produce the desired shape of the workpiece. Tool wear has been a problem for cutting tools, since cutting tools wear and break. Research has been accomplished in the tool wear field for tool life and more recently tool wear. The computer generation has created a method to simulate the material removal process. These computer simulations model the cutting tool reaction with the workpiece. Many of the simulation models use finite element analysis to calculate the reaction of the cutting tool. Different finite element models are being used throughout the world …

Manufacturing Quality Of Carbon/Epoxy Isotruss (R) Reinforced Concrete Structures, David Thomas Mccune

Theses and Dissertations

This thesis explores the quality of hand-manufactured carbon-epoxy IsoTruss® grid structures for use as reinforcement in concrete piles. Large IsoTruss® grid structures were manufactured and embedded in 14.0" (35.6 cm) diameter concrete to create IsoPiles™. The IsoPiles™ were designed to have flexural characteristics similar to steel reinforced concrete piles of equal diameter. Bending stiffness was matched based on the longitudinal members. A method for comparing transverse steel reinforcement to helical IsoTruss® members was developed, along with equations to facilitate the design of IsoTruss® structures with rounded nodes.

Compression tests were performed on 3.0 ft (0.91 m) long sections taken from …

Floodplain And Flood Probability Mapping Using Geodatabases, Douglas J. Gallup

Theses and Dissertations

This research presents methods of creating digital maps for floodplain delineation and flood probability studies and storing them in a geodatabase. Methods for creating a geodatabase for water resources outside of a GIS are presented. The geodatabase follows the ArcHydro data model. Methods are also shown for creating digital flood maps and storing them in the geodatabase. These flood maps, defining the floodplain boundary and flood probability, are stored in a digital format ready for use in a FEMA flood hazard project, allowing for better archival methods and reproducibility.

Algal Succession And Nutrient Dynamics In Elephant Butte Reservoir, Eric J. Nielsen

Theses and Dissertations

A water quality model was created for Elephant Butte Reservoir, New Mexico to understand nutrient dynamics and algal response during a three year period. The model chosen for this study was CE-QUAL-W2 because of its proven ability to represent hydrodynamics and the ability to represent multiple algal groups. Elephant Butte has been subject to large algal blooms. This study examined the phosphorus loading into the reservoir to see if it could sustain the observed algal growth. Data showed that the amount of bioavailable phosphorus was more than enough to support large blooms. This study also was an initial attempt to …

The Purposes And Evaluation Methods For State Residential General Contractor Licensing, James Ellis Fenn

Theses and Dissertations

The main topic in the licensing debate is whether licensing affects construction quality. Available literature and previous studies indicate that it does not. The real question is not whether licensing improves quality, but whether the improving quality is the actual purpose of licensing. There is little information available on the purpose of licensing as defined by state licensing departments as well as a general lack of information on how states evaluate whether licensing is fulfilling the intended purpose. In order to effectively resolve some of the issues surrounding the construction licensing debate, the true purpose of licensing and the methods …

Flexural Behavior Of Carbon/Epoxy Isotruss Reinforced-Concrete Beam-Columns, Monica Joy Ferrell

Theses and Dissertations

This thesis quantifies the flexural behavior (strength, stiffness and failure) of IsoTruss®-reinforced concrete beam-columns for use in deep foundation pile applications. Four-point bending tests were performed in the laboratory on two instrumented carbon/epoxy IsoTruss® reinforced concrete piles (IRC piles) and two instrumented steel reinforced concrete piles (SRC piles). The piles were approximately 14 ft (4.3 m) in length and 14 in (36 cm) in diameter and were loaded to failure while monitoring load, deflection, and strain data. The steel and IsoTruss®® reinforcement cages were designed to have equal flexural stiffness to permit a relative strength comparison. Moment curvature diagrams reveal …

Optimization Of Shape, Size, And Topology Design Variables In Trusses With A Genetic Algorithm, Kevin M. Gillman

Theses and Dissertations

Briggs' genetic algorithm was extended in the Gillman algorithm to include shape optimization of trusses. Other contributions include value representation, different member linking, alternate genes, automatic k-factor evaluation for buckling, and the option to prevent overlapping members. The purpose of these contributions was to make optimization using a genetic algorithm more accessible to design engineers. The Gillman algorithm was demonstrated in two original examples as well as an example from a published work. The Gillman algorithm was effective in finding lighter designs.

Computer-Simulation-Assisted Lean Manufacturing Training, Luoding Wang

Theses and Dissertations

This thesis assesses the potential of using computer simulation to aid existing lean manufacturing training methods such as lecture and live simulation. An investigation of this possibility was carried out in conjunction with UMEP's Lean 101 class. In the study, two experimental computer simulation models demonstrating the push and pull production scenarios were constructed using ProModel software. Simulation models were equipped with a Visual Basic interface to aid trainees to manipulate the model via ActiveX. Constructed computer simulation was compared with live simulation to answer these research questions: 1. Was computer simulation able to teach additional lean concepts not covered …

Performance Of Concrete Bridge Deck Joints, Lik Hang Yuen

Theses and Dissertations

The purpose of this research was to identify the types of joints available for use on concrete bridge decks and to investigate the performance characteristics of each type, including primary functions and movement ranges. Eleven reports on joint performance published by state departments of transportation and universities nationwide were analyzed in order to obtain information on joint performance problems typically encountered by state transportation agencies. In addition, test methods and specifications provided by the American Society for Testing and Materials (ASTM) were reviewed for application by bridge engineers to ensure the adequacy of deck joints.

The research indicates that compression …

New Product Launch Decisions Under Competition And Uncertainty: A Real Options And Game-Theoretic Approach To New Product Development, James O. Ostler

Theses and Dissertations

New product development is central to many firms' future success. Not only as a means to continue to maintain their piece of the market, but product development can also be a strategic means for a company to diversify, and/or alter focus to adapt to changing market conditions.

Most of the research in new product development has been on how to do it cheaper and faster than the next guy. However, early commercialization does not guarantee a position of strength in the market. Failures of EMI in CT scanners and Xerox in personal computers illustrate that being first to market does …