Civil and Environmental Engineering Commons^™

A Study Of Co2 Absorption Using Jet Bubble Column, Setiadi Setiadi, Nita Tania Hadiyani, Hantizen Hantizen, Dijan Supramono

Makara Journal of Technology

A Study of CO2 Absorption Using Jet Bubble Column. The phenomenon of plunging jet gas-liquid contact occurs quite often in nature, it's momentum carries small air bubbles with it into the reactor medium. The momentum of the liquid stream can be sufficient to carry small bubbles completely to the bottom of the vessel. A stream of liquid falling toward a level surface of that liquid will pull the surrounding air along with it. It will indent the surface of the liquid to form a trumpet-like shape. If the velocity of the stream is high enough, air bubbles will be pulled …

The Development Of Inverter Fuzzy Logic Control For Induction Motor Control By Vector Control Method In Electric Vehicle, Era Purwanto, Mohammad Ashary, Subagio Subagio, Mauridhi Heri Purnomo

Makara Journal of Technology

The development of Inverter Fuzzy Logic Control for Induction Motor Control by Vector Control Method in Electric Vehicle. In response to concerns about energy cost, energy dependence, and environmental damage, a rekindling of interest in electric vehicles (EV’s) has been obvious. Thus, the development of power electronics technology for EV’s will take an accelerated pace to fulfill the market needs, regarding with the problem in this paper is presented development of fuzzy logic inverter in induction motor control for electric vehicle propulsion. The Fuzzy logic inverter is developed in this system to directed toward developing an improved propulsion system for …

Internet Congestion Control System, Pranoto Hidaya Rusmin, Carmadi Machbub, Agung Harsoyo, Hendrawan Hendrawan

Makara Journal of Technology

Internet Congestion Control System. Internet congestion occurs when resource demands exceeds the network capacity. But, it is not the only reason. Congestion can happen on some users because some others user has higher sending rate. Then some users with lower sending rate will experience congestion. This partial congestion is caused by inexactly feedback. At this moment congestion are solved by the involvement of two controlling mechanisms. These mechanisms are flow/congestion control in the TCP source and Active Queue Management (AQM) in the router. AQM will provide feedback to the source a kind of indication for the occurrence of the congestion …

Substrates Preparation From Woody Tropical Waste Biomass For Biohydrogen Production, Dwi Susilaningsih, Theresia Umi Harwati, Khairul Anam, Yopi Yopi

Makara Journal of Technology

Substrates Preparation from Woody Tropical Waste Biomass for Biohydrogen Production. Addressing to the global warming problem, energy crisis and pollution, hydrogen production by micro-organisms using biotechnological approach should be considered, since it fulfils the recent society requirement to safely produce, renewable and environmental friendly energy. Hydrogen is one of the most promising green energy sources, because it is easily converted to electricity and cleanly combustible. There are three types of micro-organisms for hydrogen production, the first is cyanobacteria through the photosynthesis process, the second is anaerobic bacteria, which use organic substances as electron donor and energy and convert them to …

Building Fire Safety Audit At Faculty X, University Of Indonesia, Year 2006, Fatma Lestari, Rm. Yodan Amaral Panindrus

Makara Journal of Technology

Building Fire Safety Audit at Faculty X, University of Indonesia, Year 2006. Fire may cause loss of life, material and valuable assets. The objective of this study is to conduct audit for fire safety and emergency response in the building at Faculty X, University of Indonesia, Depok. The audit results on the building fire safety facilities including emergency response and preparedness are then compared to the Building Code Australia (BCA) and Indonesian regulation on the building fire safety (Kep.MenPU.No 10 and 11/KPTS/2000). The building selected are Building A, B, C, D, F and G. Building classification for A, B, D, …

Ad Hoc On-Demand Distance Vector (Aodv) Routing Protocol Performance Evaluation On Hybrid Ad Hoc Network: Comparison Of Result Of Ns-2 Simulation And Implementation On Testbed Using Pda, Riri Fitri Sari, Abdusy Syarif, Bagio Budiardjo

Makara Journal of Technology

Ad Hoc on-Demand Distance Vector (AODV) Routing Protocol Performance Evaluation on Hybrid Ad Hoc Network: Comparison of Result of Ns-2 Simulation and Implementation on Testbed using PDA. In Mobile Ad hoc NETwork (MANET), node supplemented with wireless equipment has the capacity to manage and organise autonomously, without the presence of network infrastructures. Hybrid ad hoc network, enable several nodes to move freely (mobile) to create instant communication. Independent from infrastructure. They could access the Local Area Network (LAN) or the Internet. Functionalities of ad hoc network very much dependent on the routing protocol that determines the routing around node. Ad …

Biomass Production Chlorella Vulgaris Buitenzorg Using Series Of Bubble Column Photo Bioreactor With A Periodic Illumination, Anondho Wijanarko, Dianursanti Dianursanti, Muryanto Muryanto, Josia Simanjuntak, Praswasti Pembangun Dyah Kencana Wulan, Heri Hermansyah, Misri Gozan, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

Chlorella vulgaris Buitenzorg cultivation using three bubble column photo bioreactors arranged in series with a volume of 200 mL for 130 hours shows an increase of biomass production of Chlorella vulgaris Buitenzorg up to 1.20 times and a decrease of the ability of CO2 fixation compared to single reactor at a periodic sun illumination cycle. The operation conditions on cultivation are as following: T, 29.0oC; P,1 atm.; UG, 2.40 m/h; CO2, 10%; Benneck medium; and illumination source by Phillip Halogen Lamp 20W /12V/ 50Hz. Other research parameters such as microbial carbon dioxide transferred rate (qco2), CO2 transferred rate (CTR), energy …

The Effect Of Ozone And Zeolite Concentration To The Performance Of The Treatment Of Wastewater Containing Heavy Metal Using Flotation Process, Eva Fathul Karamah, Setijo Bismo, Hotdi M. Simbolon

Makara Journal of Technology

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process. Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and …

The Role Of 1 And 9 Wt.% Zn In Precipitation Hardening Of Aa319 Aluminium, Bondan Tiara Sofyan, Sari Susanti, Ridwan R. Yusfranto

Makara Journal of Technology

The Role of 1 and 9 wt.% Zn in Precipitation Hardening of AA319 Aluminium. Aluminium alloys are widely used for automotive application due to its low density and high corrosion resistance. For economic reason, casting of automotive products always uses aluminium scrap as charging materials that may result in fluctuation of content of alloying element, such as Zn. This research studies the role of Zn in precipitation hardening of AA319 aluminium alloys. Hardness and tensile testing were conducted to study the mechanical properties of the alloys, while ageing response was followed by hardness measurements. Evolution of microstructures was observed by …

Parameters Influencing The Performance Of Reinforced Concrete-Fiber Reinforced Polymer Systems, Yosra Hesham Mohamed El Maghraby

Archived Theses and Dissertations

No abstract provided.

Abrasion Resistance Of Concrete Made With Various Types Of Aggregates, Mohamed Hamada Rashwan

Archived Theses and Dissertations

No abstract provided.

College Of Engineering Senior Design Competition Fall 2007, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Trajectory Shaping Of Surface-To-Surface Missile With Terminal Impact Angle Constraint, S. Subchan

Makara Journal of Technology

This paper presents trajectory shaping of a surface-to-surface missile attacking a fixed with terminal impact angle constraint. The missile must hit the target from above, subject to the missile dynamics and path constraints. The problem is reinterpreted using optimal control theory resulting in the formulation of minimum integrated altitude. The formulation entails nonlinear, two-dimensional missile flight dynamics, boundary conditions and path constraints. The generic shape of optimal trajectory is: level flight, climbing, diving; this combination of the three flight phases is called the bunt manoeuvre. The numerical solution of optimal control problem is solved by a direct collocation method. The …

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Reverse Link Cdma System Capacity Evaluation For Stratospheric Platform Mobile Communications, Iskandar Iskandar

Makara Journal of Technology

We propose an analysis of reverse link CDMA multispot beam stratospheric platforms (SPF) in this paper. The SPF is currently proposed as a novel wireless technology for the development of the next generation fixed and mobile communications. The geometry of this technology is different from that of the terrestrial but rather similar to the satellite based cellular system. However, evaluation on the CDMA system capacity of this technology has not been much reported. This paper addresses all possible multiple access interference analyses including the effects of channel fading and shadowing in order to evaluate the system capacity. Single SPF and …

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

Bulk Behavior Of Nanostructured Aluminum: Nanocrystalline Powders Compaction, Canning And Consolidation Via Intense Plastic Straining, Mohamed Mahmoud Hamed Shamma

Archived Theses and Dissertations

No abstract provided.

Guidelines For The Application Of Recycled Concrete Aggregate In The Egyptian Construction Industry, Ahmed Moustafa Essam Aly Kamel

Archived Theses and Dissertations

Construction industry is one of the most important fractions of economy worldwide. This industry consumes enormous amounts of raw materials and produces considerable waste. The optimization of construction material usage not only saves costs but also can significantly contribute towards sustainable development. The concept of recycling the construction and demolition rubble is being addressed in this study as a solution. The recycling of concrete, resulting from both the construction activities and the demolition activities, in order to be used as a source of aggregate is being focused upon in this study. Although the idea of using recycled concrete has been …

Optimal Utilization Of Timber Poles As Structural Members Of Formwork, Ladislaus Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

Timber poles of the type “Mirunda” are commonly used in East Africa as formwork support structures for casting of reinforced concrete slabs, beams and canopies. It is also widely known that the “Mirunda” poles as structural members of formwork are massively used without any structural consideration and guidance. This common practice has resulted into wastage of natural resources and escalated construction costs. This study has attempted to establish the load bearing capacity of randomly selected “Mirunda” poles through laboratory testing. Using an existing construction site as a case study, the results have been used to establish the actual number of …

Final Report: Second Generation Waste Package Design Study, L. S. Armijo, Mano Misra, Piyush Kar

Publications (YM)

The objectives of this project activity are: to review the current YMP baseline environment and establish corrosion test environments representative of the range of dry to intermittently wet conditions expected in the drifts as a function of time. to demonstrate the oxidation and corrosion resistance of A588 weathering steel and reference Alloy 22 samples in the representative dry to intermittently dry conditions. to evaluate backfill and design features to improve the thermal performance analyses of the proposed second-generation waste packages using existing models developed at UNR.

Properties Of Light Transmitting Concrete, Dina Abdel Mohsen Abou Alia

Archived Theses and Dissertations

No abstract provided.

Development Of Knowledge Base Of Concrete Bridge Maintenance System, Bahre Karam

Masters Theses

Bridges are the key elements of any transportation system of a country. Bridges are expensive structures and therefore, it's essential to maintain and repair them on regular basis. Almost one third of the bridges in United States are reported to be in some what deteriorated conditions. This Research presents the development of knowledge base for decision support system for concrete bridges.

During this research various concrete bridge problems are investigated including COlTosion, delamination, cracks, spalling and scour etc. The inspection tools and techniques are addressed in order to identify these problems both for above and below water surface. The various …

Biodesulphurization Within Natural Gas In Oil And Gas Field, Sri Astuti Rahayu, M. Fierdaus, Syafrizal Syafrizal, M. Udiharto

Makara Journal of Technology

The presence of sulphur compounds in natural gas can interfere to the quality of natural gas. The decline of combustion gas capacity, metal instrument corrosion in gas piping, and the environmental pollution from gas emission can affect by their presence. Bio-filter is one of the methods that selected to reduce sulphur content in natural gas. A lab scale study of hydrogen sulphide reduction in natural gas had conducted in oil and gas field using bio-filter method. The bio-filter system (±1 L volume) contains an active carbon and thiosulphide medium as a substrate, Thiobacillus thioparus as a single culture of sulphur …

Mechanical Study On Using Of Accr Thermal Conductor At 500 Kv Sutet, Suprihadi Prasetyono

Makara Journal of Technology

Mechanical Study on using of ACCR Thermal Conductor at 500 kV SUTET. At the height of electricity demand increasing recently, circumstance of environment more limited and also expense of high investment, making thermal conductor (conductor thermal resistance) considered to be one of alternative in the electricity transmission bottlenecks. These days it has been developed thermal conductor ACCR (Aluminium Conductor Composite Reinforced) which can operate with temperature up to 240oC, so that making the current carrying capacity being higher than conventional conductor. This research aimed to study load current leading to mechanical characteristic ACCR conductor included tension, length of elongation and …

Behaviour Of Reinforced Self-Consolidating Concrete Frames, Aly Said, Moncef Nehdi

Civil and Environmental Engineering and Construction Faculty Research

Multi-storey reinforced concrete (RC) structural frames represent some of the most congested structural elements. Placing and consolidating concrete in such structural frames imposes substantial challenges. This offers a unique area of application for self-consolidating concrete (SCC) because of its inherent ability to flow under its own weight and fill congested sections, complicated formwork and hard-to-reach areas. Research is, however, needed to demonstrate the ability of SCC structural frames adequately to resist vertical and lateral loads. In the present study, full-scale 3 m high beam-column joints reinforced as per the Canadian Standards CSA A23·3-94 and ACI-352R-02 were made with normal concrete …

Production Of Medium Chain Length Polyhydroxyalkanoates From Oleic Acid Using Pseudomonas Putida Pga1 By Fed Batch Culture, Sidik Marsudi, Irene K.P. Tan, Seng Neon Gan, K. B. Ramachandran

Makara Journal of Technology

Bacterial polyhydroxyalkanoates (PHAs) are a class of polymers currently receiving much attention because of their potential as renewable and biodegradable plastics. A wide variety of bacteria has been reported to produce PHAs including Pseudomonas strains. These strains are known as versatile medium chain length PHAs (PHAs-mcl) producers using fatty acids as carbon source. Oleic acid was used to produce PHAs-mcl using Pseudomonas putida PGA 1 by continuous feeding of both nitrogen and carbon source, in a fed batch culture. During cell growth, PHAs also accumulated, indicating that PHA production in this organism is growth associated. Residual cell increased until the …