Civil and Environmental Engineering Commons^™

Abrasion Resistance Of High Early-Strength Concrete For Rapid Repair, Nader Ghafoori, Matthew O. Maler, Meysam Najimi, Ariful Hasnat

Civil and Environmental Engineering and Construction Faculty Research

This paper examines the abrasion resistance of high early-strength concrete developed for rapid repair of highways and bridge decks. The cement types chosen for this study included ASTM Type III, ASTM Type V, and Calcium Sulfoaluminate (CSA) cements. A cement content of 386 kg/m3 (650 lb/yd3 ) was maintained for all studied concretes. Test samples were tested after 24 hours and 28 days of curing in order to evaluate compressive strength and depth of wear. Test results revealed that the opening time to attain minimum required compressive strength for CSA cement concrete was one hour, whereas the values for Type …

Optimizing The Valorization Of Industrial By-Products For The Induction Healing Of Asphalt Mixtures, Amir Tabakovic, Marta Vila-Cortavitarte, Daniel Jato-Espino, Daniel Castro-Fresno

Articles

Self-healing within asphalt pavements is the process whereby road cracks can be repaired automatically when thermal and mechanical conditions are met. To accelerate and improve this healing process, metal particles are added to asphalt mixtures. However, thisapproach is costly both in economic and environmental terms due to the use of virgin metallic particles. So, even though the self-healing of asphalt mixtures has been widely addressed in experimental terms over the years, there is a lack of research aimed at modelling this phenomenon, especially with the purpose of optimizing the use of metal particles through the valorization of industrial by-products. As …

Hydcem: A New Cement Hydration Model, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models are useful to predict, understand and describe the behaviour of different cementitious-based systems. They are indispensable for undertaking long-term performance and service life predictions for existing and new products for generating quantitative data in the move towards more sustainable cements while optimising natural resources. One such application is the development of cement-based thermoelectric applications.

HYDCEM is a new model to predict the phase assemblage, degree of hydration, heat release and changes in pore solution chemistry over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, is aimed at …

Laboratory Evaluation Of Cold In-Place Recycling Asphalt Mixtures Using A Balanced Mix Design, Ahmed Saidi

Theses and Dissertations

The objective of this research study is to present a procedure for designing Cold In-Place Recycling (CIR) mixtures through balancing cracking and rutting for these mixtures. Eight CIR mixtures were prepared using two recycling agents (foamed and emulsified asphalts), then cured for three days at two temperatures (140oF and 50oF), and compacted at two gyration levels (30 and 70 gyrations). The CIR mixtures were prepared at constant dosages of water and cement, 3% and 1%, respectively. Air void of each CIR performance test specimen was determined using the CoreLok device. The rutting susceptibility of these mixtures was then evaluated using …

General Nonlinear-Material Elasticity In Classical One-Dimensional Solid Mechanics, Ronald Joseph Giardina Jr

LSU New Orleans Theses and Dissertations

We will create a class of generalized ellipses and explore their ability to define a distance on a space and generate continuous, periodic functions. Connections between these continuous, periodic functions and the generalizations of trigonometric functions known in the literature shall be established along with connections between these generalized ellipses and some spectrahedral projections onto the plane, more specifically the well-known multifocal ellipses. The superellipse, or Lam\'{e} curve, will be a special case of the generalized ellipse. Applications of these generalized ellipses shall be explored with regards to some one-dimensional systems of classical mechanics. We will adopt the Ramberg-Osgood relation …

Long-Term Performance Of Sustainable Pavements Using Ternary Blended Concrete With Recycled Aggregates, Seth M. Wagner

Theses and Dissertations

The purposes of this study were to (a) design concrete pavement mixtures with recycled concrete aggregates using ternary blends of cementitious materials and a low water-to-binder ratio, (b) measure the fresh and hardened properties of the proposed concrete mixtures and (c) assess the long-term performance of the concrete implementing the use of recycled coarse aggregates. Preliminary investigation into ternary blend combinations via the compressive testing of mortar cubes and isothermal calorimetry was used to predict an optimal blend of cementitious material. Mixes using recycled concrete aggregates at varying replacement rates were tested for fresh and hardened properties using the proposed …

A Study Of The Electron Regeneration Efficiency Of Solar Cells Fabricated Using Cmc/Pva-, Alginate-, And Xanthan-Based Electrolytes, Nur Farha Shaafi, Saifful Kamaluddin Muzakir, Bouchta Sahraoui

Makara Journal of Technology

A photovoltaic (PV) mechanism consists of three important steps, i.e., (i) electron excitation upon absorption of photon with energy higher than the bandgap of fluorophore, (ii) excited-state electron injection from the fluorophore to the pho-toelectrode, and (iii) electron regeneration from the electrolyte to the fluorophore. An efficient electron regeneration could be achieved upon fulfillment of the requirements of energy alignment, i.e., lowest unoccupied molecular orbital of fluorophore (LUMOfluorophore) > redox potential of electrolyte > highest occupied molecular orbital of fluorophore (HOMOfluorophore). This study investigated the electron regeneration efficiency of excitonic solar cells fabricated using three polymer-based electrolytes, i.e., (i) 60% carboxymethyl cellulose …

Use Of The “Dnachecker” Algorithm For Improving Bioinformatics Research, Nausheen Bhat, Ezra Bernadus Wijaya, Arli Aditya Parikesit

Makara Journal of Technology

Basic Local Alignment Sequencing Tool (BLAST) is a bioinformatics tool used for analyzing nucleotide sequences with regards to their similarity. BLAST can be found online on biological databases such as the National Center for Biotechnology Information (NCBI) and other such repositories. The mechanism of BLAST allows the target sequence to be compared with other sequences to find regions of local similarity, and thus, a comparability quotient that determines the resemblance between the sequences is created. Due to the open-platform nature of the online databanks, several sequences can be accepted with little to no interjections regarding the quality of sequence submitted. …

Study Of Ecological Design Of Residential Complexes Using Spss To Elevate Resident Satisfaction, Soheil Malekpour Kolbadinejad, V. Malekpour Ravasjan, A. Darvish

Makara Journal of Technology

This article reports the general residential satisfaction, affecting ecological factors, and their importance in area in Tehran. The collected field data was analyzed using SPSS. Cronbach's alpha variable was used to determine the reliability of the questionnaire and the Friedman test was used to assess priorities that influence residential satisfaction. The results show that the quality of residential environments and general satisfaction of their residents may be enhanced by identifying these criteria and making appropriate plans for their improvement.

Adsorption Of Heavy Metal Ions By Oil Palm Decanter Cake Activated Carbon, Mohd. Ezreeza Mohamed Yusoff, Juferi Idris, Nahrul Hayawin Zainal, Mohamad Faizal Ibrahim, Suraini Abd-Aziz

Makara Journal of Technology

Adsorption processes are widely used for the removal of heavy metals from waste streams. Oil palm decanter cake (OPDC) is used as a bioadsorbent because of its compositional properties for activated carbon production; moreover, it is a readily available raw material produced in palm oil mills and is thus abundant and cheap. In this study, the OPDC was carbonized at 700 °C and activated using steam at 700 °C to produce oil palm decanter cake activated carbon (AC-OPDC). Batch adsorption experiments were carried out to compare the adsorption capacities of the raw OPDC and the AC-OPDC for heavy metals removal. …

Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks, Heru Purnomo, Srikandi Wahyu Arini

Makara Journal of Technology

Unfired brick is considered as a more environmentally friendly material than fired brick. It has lower mechanical properties than that of fired brick where humidity influences both bricks. Physical and mechanical properties of unfired bricks made of three kinds of mixtures were studied experimentally under three humidity conditions. The first kind of unfired brick was made only with soil and water while the second type was made of a mixture of soil, water and lime, and the third type was a mixture of soil, water, lime and uniform treated coir where 4% of lime mass was substituted with coir mass. …

Component Analysis And Antiangiogenic Activity Of Thailand Stingless Bee Propolis, Eriko Ishizu, Sari Honda, Tosihro Ohta, Boonyadist Vongsak, Shigenori Kumazawa

Makara Journal of Technology

Propolis is a natural resin produced by honey bees from certain plants, has gained popularity as a food and alternative medicine. However, to the best of our knowledge, few studies on native Thailand stingless bee propolis are available. Information on the chemical composition and biological activities of propolis is needed to investigate its potential utility. Recently we have reported the possible plant origin of Thailand stingless bee propolis, Garcinia mangostana. In this study, further component analysis, functional evaluation, and identification of the plant origin of Thailand stingless bee propolis are conducted. Nine xanthones, including α-mangostin, garcinone C, γ-mangostin, cochinchinone T, …

3d Fdtd Method For Modeling Of Seismo-Electromagnetics Disturbance On Crustal Earth, Nabila Husna Shabrina, Yasuhide Hobara, Achmad Munir

Makara Journal of Technology

The paper deals with the modelling of seismo-electromagnetics disturbance on the crustal earth by use of threedimensional (3D) finite-difference time-domain (FDTD) method. The model is built up by discretizing the frontier geographical region between Java Island and Sumatra Island in a cylindrical coordinate system-based 3D object. The proposed method is applied to compute and analyze electromagnetics (EM) fields of the observed very low frequency (VLF) wave used for the investigation. Boundary condition of uniaxial perfectly matched layer (UPML) are applied surrounding the area of computation for truncating the object of simulation. The investigation are focused on the propagation time of …

Migration And Electropolymerization Of Methyl Methacrylate In Hardened Cement Paste Via Electrokinetic Treatment, Xi Xie

Doctoral Dissertations

Porous concrete structures are susceptible to the intrusion of chemical species, such as sulfates, chlorides, and carbon dioxide. Many technologies have been developed to repair or rehabilitate damaged concrete. These include cathodic protection, corrosion inhibitor addition, or the use of coatings and sealers. In recent years, a developing technology, electrokinetic nanoparticle treatment, has been shown to reduce concrete porosity, increase strength, promote corrosion resistance, and extend durability. This dissertation was conducted to explore a novel treatment to reduce the porosity of concrete via the application of electrokinetic transportation and electro-initiated polymerization of methyl methacrylate (MMA).

Potassium persulfate (PSP) was used …

Use Of Rice Husk Ash (Rha) In Flowable Fill Concrete Mix Material, Zahid Hossain, Kazi Tamzidul Islam

Data

Corresponding data set for Tran-SET Project No. 18CASU03. Abstract of the final report is stated below for reference:

"In the way of finding sustainable development, the flowable fill is a relatively new construction technology. Flowable fill is a self-compacting material, which has been developed in recent years. Flowable fill has been used for different applications such as backfilling walls, sewer trenches, bridge abutments, conduit trenches, pile excavations, and retaining walls. This study examines the potential uses of Rice Husk Ash (RHA) as a sustainable cementitious material (SCM) in the preparation of flowable fill concrete. (RHA is an agricultural by-product of …

Self-Healing Concrete Using Encapsulated Bacterial Spores In A Simulated Hot Subtropical Climate, Marwa Hassan, Jose Milla, Tyson Rupnow, Ahsennur Soysal

Data

Corresponding data set for Tran-SET Project No. 18CLSU02. Abstract of the final report is stated below for reference:

"Bacterial concrete has become one of the most promising self-healing alternatives due to its capability to seal crack widths through microbial induced calcite precipitation (MICP). In this study, two bacterial strains were embedded at varying dosages (by weight of cement) in concrete. Beam specimens were used to identify the maximum crack-sealing efficiency, while cylinder samples were used to determine their effects on the intrinsic mechanical properties, as well as its stiffness recovery over time after inducing damage. The concrete specimens were cured …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez-Wing, Michele Barbato

Data

Corresponding data set for Tran-SET Project No. 18CLSU03. Abstract of the final report is stated below for reference:

"The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Data

Corresponding data set for Tran-SET Project No. 18STTAM02. Abstract of the final report is stated below for reference:

"This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples …

Elimination Of Empirical, Ineffective And Expensive Pg Plus Tests To Characterize Modified Binders, Zahid Hossain, Ashraf Elsayed, Mm Tariq Morshed, Mohammad Hassan

Data

Corresponding data set for Tran-SET Project No. 18BASU02. Abstract of the final report is stated below for reference:

"For characterizing the polymer modified binders, different state Departments of Transportation (DOTs) use different time consuming and empirical Performance Grade (PG) Plus test methods. Furthermore, the PG Plus tests are silent when asphalt binders are modified with chemicals such as polyphosphoric acid (PPA). But, the effects of the elastomeric or plastomeric polymer are not accurately identified through these conventional tests such as Elastic Recovery (ER) and tenacity. Thus, the main research goal of this study is to recommend alternative test method(s), which …

Elimination Of Empirical, Ineffective And Expensive Pg Plus Tests To Characterize Modified Binders, Zahid Hossain, Ashraf Elsayed, Mm Tariq Morshed, Mohammad Hassan

Publications

For characterizing the polymer modified binders, different state Departments of Transportation (DOTs) use different time consuming and empirical Performance Grade (PG) Plus test methods. Furthermore, the PG Plus tests are silent when asphalt binders are modified with chemicals such as polyphosphoric acid (PPA). But, the effects of the elastomeric or plastomeric polymer are not accurately identified through these conventional tests such as Elastic Recovery (ER) and tenacity. Thus, the main research goal of this study is to recommend alternative test method(s), which can possibly be pursued by using a commonly available device, a Dynamic Shear Rheometer (DSR). Three PG binders …

Use Of Rice Husk Ash (Rha) In Flowable Fill Concrete Mix Material, Zahid Hossain, Kazi Tamzidul Islam

Publications

In the way of finding sustainable development, the flowable fill is a relatively new construction technology. Flowable fill is a self-compacting material, which has been developed in recent years. Flowable fill has been used for different applications such as backfilling walls, sewer trenches, bridge abutments, conduit trenches, pile excavations, and retaining walls. This study examines the potential uses of Rice Husk Ash (RHA) as a sustainable cementitious material (SCM) in the preparation of flowable fill concrete. (RHA is an agricultural by-product of the rice milling process. This study has evaluated the usage of RHA in producing low strength and self-consolidating …

Self-Healing Concrete Using Encapsulated Bacterial Spores In A Simulated Hot Subtropical Climate, Marwa Hassan, Jose Milla, Tyson Rupnow, Ahsennur Soysal

Publications

Bacterial concrete has become one of the most promising self-healing alternatives due to its capability to seal crack widths through microbial induced calcite precipitation (MICP). In this study, two bacterial strains were embedded at varying dosages (by weight of cement) in concrete. Beam specimens were used to identify the maximum crack-sealing efficiency, while cylinder samples were used to determine their effects on the intrinsic mechanical properties, as well as its stiffness recovery over time after inducing damage. The concrete specimens were cured in wet-dry cycles to determine their feasibility in Region 6. The results showed that the specimen groups with …

Workforce Development Symposiums For Uhpc, Brad Weldon, Craig Newtson, Grace Mcmurry, Leticia Davila

Publications

Ultra-high performance concrete (UHPC) is a cementitious material with a dense microstructure that contributes to high compressive strengths as well as enhanced durability properties. UHPC also possesses significant post-cracking strength and ductility due to the addition of fibers. These characteristics produce a material that provides advantages over conventional concrete; however, high costs attributed to materials and production, lack of industry familiarity and knowledge, and the absence of standardized design procedures have impeded its widespread use. To help disseminate knowledge on UHPC, two workforce development symposiums on UHPC were held in Las Cruces, New Mexico. The symposiums consisted of presentations and …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez, Michele Barbato

Publications

The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed challenging for large-scale industrial application due to low SCBA yield (i.e., 3 to 6%). On the other hand, …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Publications

This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples were subjected to abnormal grain growth heat treatments and found out that part size be increased up to …

Microstructural Effects On Photocatalytic Performance In Ag3po4/Bi2moo6 Z-Scheme Photocatalyst Systems, Kaleab Mengesha Ayalew

UNLV Theses, Dissertations, Professional Papers, and Capstones

As the world population continues to grow and access to modern industry become increasingly common, humanity finds itself amid an environmental and energy crisis. Natural resources, such as clean water are getting scarce. Currently, the development of high efficiency, green energy sources, and eco-friendly methods for water treatment have become a nonelective task. As a result, photocatalysis, as one of the most promising technologies in utilizing solar energy and pollutant removal, has attracted considerable attention.

However, the practical application of photocatalysis is still elusive because of the difficulty of finding an individual material that can satisfy all the requirements for …

Effect Of External Expanded Polystyrene (Eps) Panels On Slabs Subjected To Impact Load, Yosra El Maghraby

Civil Engineering

No abstract provided.

Investigating The Rapid Curing Possibility Of Geopolymer Concrete, Ashlesh Banjara

Master's Theses

Recent studies of heat-cured fly ash based green geopolymer concrete have shown its suitability for fabrication of structural members. Fabrication of these structural members requires continuous moderate heating (145°F) for 24 hrs, and an oven essential, for a large member can quickly turn into an energy guzzler, potentially eliminating the green credentials of the product. The proposed research involves the development of a frontal polymerization (FP) method that achieves rapid curing of geopolymer at ambient condition after short-term heat application. Initial work shows thermal FP in geopolymer is a possibility and might be a solution to the problem. The process …