Civil and Environmental Engineering Commons^™

Improving Operational Hydrologic Forecasting Via Conditional Bias-Penalized Multi-Sensor Precipitation Estimation And Multi-Model Streamflow Prediction, Ali Jozaghi

Civil Engineering Dissertations - Archive

Many multivariate analysis techniques involve minimizing mean square error (MSE) or error variance under unbiasedness. In the presence of observation error, variance minimization tends to introduce negative and positive biases, or conditional bias (CB), over the upper and lower tails of the predictands, respectively. This work describes and evaluates three multivariate merging techniques, 1) adaptive conditional bias-penalized cokriging (CBPCK), 2) conditional bias-penalized Multiple Linear Regression (CBP-MLR), and 3) conditional bias-penalized Bayesian Model Averaging (CBP-BMA) which implements CBP-MLR in place of MLR. CBPCK and CBP-MLR minimize a linearly weighted sum of errors squared and the sum of the Type-II error squared, …

Urban Arterial Lane Flow Distribution: A Before And After Traffic Microsimulation Analysis On The Effect Of Implementing New Route Markings And Signage., Larry Michael Summers

Electronic Theses and Dissertations

Urban arterials may not effectively utilize available lanes to move vehicles efficiently as drivers try to establish position along the corridor. This study evaluates lane flow distribution before and after implementing new route markings and overhead signs to utilize existing lanes better. A cellphone-based traffic data service called StreetLight gathered the traffic data used to establish the VISSIM model parameters for simulating current and projected conditions. This study shows that the lane assignment signage and route markers affected the lane flow distribution in the simulation. The simulation indicated the existing condition had average queue lengths of 320.6 meters, average travel …

Design Of Load Bearing Wall For Low Rise Building With Partially Grouted Reinforced Masonry, Anil Bhatt

Honors Theses

The seismic and wind load acting on the 2-storeyed building of dimension 120 ft x 98 ft located in Oxford, MS, were calculated and the seismic load was considered for the design of the 120 ft long and 24 ft high load-bearing wall because it being critical. The maximum loading was computed using different load combinations. The masonry behavior and masonry specifications were considered to select the masonry unit, grout, and mortar for the load-bearing wall. The seismic design requirement for the shear and slender wall was fulfilled for the special reinforced masonry wall. The in-plane and out-of-plane loading scenarios …

Application Of Machine Learning In Flood Depth Prediction, Armando Esquivel

Open Access Theses & Dissertations

Machine learning technologies have helped provide answers for problems with a high degree of complexity. Machine learning has been utilized by various disciplines within the Civil Engineering profession and has proven to be efficient in solving complex problems. Although machine learning is being used in the Civil Engineering profession, a formal framework on developing and integrating machine learning has not been developed for flood depth prediction. The proposed word uses machine learning to predict the depth of flood at Houston, TX, due to a 100-year 24-hour storm. The proposed work can be used to collect, store and analyze data to …

Geotechnical Aspects Of Martian Regolith Simulant Jsc Mars-1, Jesus Baca

Open Access Theses & Dissertations

The primary objective of this research was to mechanistically characterize the physical and mechanical properties of the JSC Mars-1 regolith simulant to better understand its physical, mechanical, and physio-chemical properties. JSC Mars-1 is a regolith simulant developed by the National Aeronautics and Space Administration (NASA) at the Johnson Space Center (JSC) based on the data collected by instruments on the Viking and the Pathfinder landers. A comprehensive experiment matrix was devised to simulate the extraterrestrial compaction characteristics of unbound simulants in the laboratory. The resilient properties, strength parameters, and deformation potential were of primary interest in this effort. In addition, …

Impact Of Covid-19 On City Streets, Mihir Sharma

Honors Scholar Theses

Covid-19 has had a severe impact on the urban fabric of many cities and caused disruption to the current way of living. This paper attempts to shed light on the impact that Covid-19 has had on the city streets and how city streets have adapted to the disruptions brought on by the virus. Furthermore the paper lays down recommendations that cities can use to make their streets healthier and safer

Building Services Engineering May/June 2021

Building Services Engineering

No abstract provided.

Impact Of Antecedent Wetness And Rainfall Spatial Variability On Design Floods, Rachael Nicole Mcmahon

Theses and Dissertations

In the absence of long hydrologic records, water engineering design application rely primarily on the concept of design storms and subsequently design floods. However, despite the long-lasting use of these approaches there are several aspects that merit careful consideration and possibly revision. Representation of spatial variability of rainfall extremes in design storms has relied primarily on the use of area reduction factors that while useful, they do not represent realistic patterns of flood inducing storms. Furthermore, the impact of antecedent wetness on the transformation of design storms to design floods is often neglected. In this work we carry out a …

Editorial: Let's Talk About P(Ee), Brooke K. Mayer

Civil and Environmental Engineering Faculty Research and Publications

Practitioner points

• Phosphorus recycling and reuse are imperative, and the water industry has an important role to play in this effort.
• Technologies capable of removing phosphorus to ultra-low levels and subsequent recovery for phosphorus reuse are needed.
• Inorganic ion exchange resins and organic bioadsorbents are promising for phosphorus removal and recovery as part of the waste-to-resource paradigm.

Geometric Quality Assessment Of A Modular House Using Bim And Photogrammetric Point Clouds, Preetam Kapsikar

UNLV Theses, Dissertations, Professional Papers, and Capstones

As-built documentation of modular structures is an important set of records for a project, that consist of construction drawings and specifications, project design modifications, prefabrication, and component assembly. In particular, manual geometric quality assessments of a structure’s prefabricated components are generally fraught with errors, making it extremely difficult to compare the as-built construction with the specified drawings, which affects the project. Furthermore, if the prefabricated components are manufactured with errors, this can result in construction schedule delays and high additional costs due to rework. Several technologies, such as point cloud data generated using laser sensors and LiDAR, have been developed …

Analysis And Uncertainty Reduction Through Data Augmentation In Hurricane Risk Modeling In The State Of Florida, Daphne Raquel Otarola Farah

Theses and Dissertations

The Florida Public Hurricane Loss Model (FPHLM) and the Florida Public Flood Loss Model (FPFLM) project insurance losses due to hurricane events in the State of Florida from hurricane induced wind, rain, and flood. This hurricane catastrophe model estimates annual average loss costs, as well as mean loss levels for scenario events, for personal and commercial residential portfolios, including building structure, content, appurtenant, and additional living expenses. Insurance companies use these hurricane risk models in Florida, and in particular the Florida Office of Insurance Regulation (OIR) mandates that the FPHLM be used for the stress test, that verifies the actuarial …

Compound Extremes Drive The Western Oregon Wildfires Of September 2020, John T. Abatzoglou, David E. Rupp, Larry W. O'Neill, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Several very large high‐impact fires burned nearly 4,000 km² of mesic forests in western Oregon during September 7–9, 2020. While infrequent, very large high‐severity fires have occurred historically in western Oregon, the extreme nature of this event warrants analyses of climate and meteorological drivers. A strong blocking pattern led to an intrusion of dry air and strong downslope east winds in the Oregon Cascades following a warm‐dry 60‐day period that promoted widespread fuel flammability. Viewed independently, both the downslope east winds and fuel dryness were extreme, but not unprecedented. However, the concurrence of these drivers resulted in compound extremes …

A Magneto-Mechanical Piezoelectric Energy Harvester Designed To Scavenge Ac Magnetic Field From Thermal Power Plant With Power-Line Cables, Quan Wang, Kyung-Bum Kim, Sang-Bum Woo, Yooseob Song, Tae-Hyun Sang

Civil Engineering Faculty Publications

Piezoelectric energy harvesters have attracted much attention because they are crucial in portable industrial applications. Here, we report on a high-power device based on a magneto-mechanical piezoelectric energy harvester to scavenge the AC magnetic field from a power-line cable for industrial applications. The electrical output performance of the harvester (×4 layers) reached an output voltage of 60.8 V_max, an output power of 215 mW_max (98 mW_rms), and a power density of 94.5 mW_max/cm³ (43.5 mW_rms/cm³) at an impedance matching of 5 kΩ under a magnetic field of 80 …

Medical Service Facility Site Development, Sabrina Carvajal

Honors Theses

This report provides a clear description of a site development design project for a future medical service facility. The site is approximately 46,818 square feet and is located at 203 E. Centre Avenue Portage, Michigan 49002 United States. This is in a high traffic area that is surrounded by different public and academic institutions including Portage Central High School and Portage Public Library. The commercial buildings surrounding this area are Comerica Bank, Dairy Queen and a new Senior Center currently under construction. Our team is proposing two different site-layout options for the future development of this building. This medical service …

Editorial: Forest Management Alters Forest Water Use And Drought Vulnerability, Christina Tague, Matthew D. Hurteau, Anthony J. Parolari

Civil and Environmental Engineering Faculty Research and Publications

This collection of papers provides new insights into how forest management, forest water use and droughts are interrelated. The collection considers both ecohydrologic impacts of changes in forest density (through thinning or fire) and impacts that could occur via species management.

Modeling Considerations For Built-Up Compression Members In Communication Towers, Ghada M. El-Mahdy P.Eng., Ceng, Amro A. Alawamry

Civil Engineering

It is a well-established fact that built-up compression members exhibit extra flexibility than their equivalent solid members due to the shear action which effects the overall stability. This is usually taken into consideration by using a modified slenderness ratio for buckling modes that involve relative deformation of the interconnectors. Built-up members are often used as space truss members in communication towers. When modeling communication towers in structural analysis programs like SAP2000, the built-up member is usually defined as a single member element with a double section cross section. This does not catch the increase in deflection in the member due …

A Flexible Piezoelectric Energy Harvester-Based Single-Layer Ws2 Nanometer 2d Material For Self-Powered Sensors, Quan Wang, Kyung-Bum Kim, Sang Bum Woo, Yooseob Song, Tae Hyun Sung

Civil Engineering Faculty Publications

A piezoelectric sensor is a typical self-powered sensor. With the advantages of a high sensitivity, high frequency band, high signal-to-noise ratio, simple structure, light weight, and reliable operation, it has gradually been applied to the field of smart wearable devices. Here, we first report a flexible piezoelectric sensor (FPS) based on tungsten disulfide (WS₂) monolayers that generate electricity when subjected to human movement. The generator maximum voltage was 2.26 V, and the produced energy was 55.45 μJ of the electrical charge on the capacitor (capacity: 220 μF) when applying periodic pressing by 13 kg. The generator demonstrated here …

Evaluation Of Permanent Concrete Barriers To Mash 2016, Samuel Elias Hovde

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to develop evaluation criteria for permanent concrete barriers to MASH 2016 TL-3 and TL-4 without crash testing and then to evaluate permanent concrete barrier standards provided by the sponsoring agencies of the Midwest Pooled Fund Program. A literature review was conducted to determine evaluation criteria for stability, shape, strength, and anchorage, and a database of permanent concrete barrier crash tests was compiled. A survey was conducted to collect barrier standards from the members of the Midwest Pooled Fund Program, and barriers were selected and evaluated according to the determined methodology. A total of …

Hydrodynamic Analysis Of A Wave Energy Converter (Wec), A. Kapperman, B. Rodriguez, A. Daniels, C. Harrison, P. Tubuntoeng, L. Fernandez De Valderrama, B. Labban, J. Whipple, C. Akan, N. Ozdemir

Showcase of Osprey Advancements in Research and Scholarship (SOARS)

Honorable Mention Winner

The UNF CREW competing in the U.S. Department of Energy 2021 Marine Energy Collegiate Competition developed a Wave Energy Converter (WEC) for quick deployment in disaster relief areas. When natural disasters disable coastal power grids, a WEC can be easily deployed close to shore and serve as a source of electricity. The ocean waves move magnets through a coil wired within the WEC to generate electricity. To initiate the design process, ANSYS AQWA software simulated both the oceanic environment and the device’s response in the WEC’s testing conditions. AQWA allows the user to change device dimensions easily …

Quantifying Surface Morphology Of Manufactured Activated Carbon And The Waste Coffee Grounds Using The Getis-Ord-Gi* Statistic And Ripley’S K Function, Sanghoon Lee, Sukjoon Na, Olivia G. Rogers, Sungmin Youn

All Engineering Faculty Research

Activated carbon can be manufactured from waste coffee grounds via physical and/or chemical activation processes. However, challenges remain to quantify the differences in surface morphology between manufactured activated carbon granules and the waste coffee grounds. This paper presents a novel quantitative method to determine the quality of the physical and chemical activation processes performed in the presence of intensity inhomogeneity and identify surface characteristics of manufactured activated carbon granules and the waste coffee grounds. The spatial density was calculated by the Getis-Ord-Gi* statistic in scanning electron microscopy images. The spatial characteristics were determined by analyzing Ripley’s K function and complete …

Effects Of Historical Land-Use Change On Surface Runoff And Flooding In The Amite River Basin, Louisiana, Usa Using Coupled 1d/2d Hec-Ras–Hec-Hms Hydrological Modeling, Alexandre G. H. Cowles

LSU Master's Theses

The Amite River Basin is a largely rural watershed spanning parts of four counties in southern Mississippi and seven parishes in southeast Louisiana, with basinwide imperviousness increasing from 0.82% in 1938 to 3.85% in 2016. The Basin has been the subject of significant research interest since catastrophic flooding in 2016 caused 13 deaths and widespread damages. Rapid development in recent decades has led to an expansion of impervious surfaces in Baton Rouge and surrounding areas, encroaching on floodplains and wetlands. At the basin scale, differences in flooding due to impervious cover changes were found to be somewhat limited, particularly along …

Pooling Data Improves Multimodel Idf Estimates Over Median-Based Idf Estimates: Analysis Over The Susquehanna And Florida, Abhishekh Kumar Srivastava, Richard Grotjahn, Paul Aaron Ullrich, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Traditional multimodel methods for estimating future changes in precipitation intensity, duration, and frequency (IDF) curves rely on mean or median of models’ IDF estimates. Such multimodel estimates are impaired by large estimation uncertainty, shadowing their efficacy in planning efforts. Here, assuming that each climate model is one representation of the underlying data generating process, i.e., the Earth system, we propose a novel extension of current methods through pooling model data: (i) evaluate performance of climate models in simulating the spatial and temporal variability of the observed annual maximum precipitation (AMP), (ii) bias-correct and pool historical and future AMP data of …

Distributionally Robust Optimization Utilizing Facility Location Problems, Elijah Kling

Civil and Environmental Engineering Undergraduate Honors Theses

Facility location problems are used in widespread application in transportation, freight, supply chain, and logistics problems. Models can be developed as deterministic, where all parameters are known, or robust, where a parameter has uncertainty. This thesis explores a new method for developing robust formulation and compares the implications of assuming values for this uncertain parameter. Two models are solved, and both are compared against their deterministic counterparts using numerical analysis. By manipulating the input parameters and considering real world implications of the solutions, either the robust or deterministic can show better performance.

The Influence Of Channel Deepening On Tides, River Discharge Effects, And Storm Surge, Stefan A. Talke, Ramin Familkhalili, David A. Jay

Civil and Environmental Engineering Faculty Publications and Presentations

We combine archival research, semi-analytical models, and numerical simulations to address the following question: how do changes to channel geometry alter tidal properties and flood dynamics in a hyposynchronous, strongly frictional estuary with a landward decay in tidal amplitudes? Records in the Saint Johns River Estuary since the 1890s show that tidal range has doubled in Jacksonville, Florida. Near the estuary inlet, tidal discharge approximately doubled but tidal amplitudes increased only ~6%. Modeling shows that increased shipping channel depths from 5-6 to ~13m drove the observed changes, with other factors like channel shortening and width reduction producing comparatively minor effects. …

Characterization Of Uranium, Lead, And Rare Earth Element Pollution In Natural Soils And Sediments, Hope Rasmussen

Civil and Environmental Engineering Theses and Dissertations

Heavy metals in the environment add to the global burden of pollution, negatively impacting public health and ecosystem resilience. This study included projects regarding uranium (U), lead (Pb), and rare earth elements (REE) in natural samples, due to their known toxicity, ubiquity, and relevance in context to recent pollution trends. The first project focused on testing the potential of using a hydroxyapatite product as a remediation solution for U-contaminated groundwater and soil at an EPA Superfund site. The results showed that the U was sequestered in a highly crystalline mineral form within the solids, guiding the EPA to specify the …

Damage Evolution And High-Rate Response Of High-Strength Concrete Under Triaxial Loading, Brett Williams

Mechanical Engineering Research Theses and Dissertations

The research presented in this study focuses on understanding fundamental mechanisms that drive material response under dynamic loading conditions. The objectives of the research were to: (1) to understand damage initiation and propagation in the bulk geomaterial under a variety of loading conditions and (2) to systematically investigate the strain rate effects on the triaxial compressive response of cementitious materials through the development of an innovative, first of its kind large-diameter (50 mm) triaxial Kolsky bar system.

The triaxial compressive response of high-strength concrete is needed to understand pressure-dependent material behavior, which is important for modeling extreme loading events. However, …

Study Of Fragility Functions For Assessing Damage To Water Pipe Networks Caused By Earthquake Loading, Dylan Joseph Merlo

Master's Theses

The performance of water lifelines during seismic events is an area of ongoing research. In this study we evaluate eight (8) different seismic events and the impact that ground shaking and ground deformations had on water pipeline systems. The overall goal of this work is to provide municipalities and utility providers with tools for mitigating the consequences of seismic hazards on water lifeline systems by analyzing the accuracy of damage estimation models. Three (3) different repair rate models are evaluated using data collected from the seismic events and compared to observed repair rate data. Results are analyzed to examine the …

The Effect Of Lanthanides On Corn Growth, Savanna Vacek

Undergraduate Research Symposium Podium Presentations

Wastewater treatment plants (WWTPs) offer a reliable source of reclaimed water for irrigation. Metal-based chemicals (i.e. coagulants) are frequently employed in wastewater treatment, and residual metal ions remain in the treated wastewater, which could result in application of these metal ions to agricultural fields and crops. This study focuses on an emerging coagulant containing lanthanum. The behavior of lanthanum reclaimed water (LaRW) towards corn growth is barely known. Thus, if we are to recycle LaRW to support corn growth, the effects of LaRW on corn growth need to be studied. Corn kernels were grown in varying lanthanum concentrations (0-5000 mg …

Stability Of Low Crested And Submerged Breakwaters: A Reanalysis And Model Development, Christopher P. Burgess

Civil & Environmental Engineering Theses & Dissertations

Low-crested and submerged structures (LCS) play an integral part in the stabilization of shorelines for recreational purposes, yet there are a plethora of empirical models and gaps in the understanding of their stability and damage progression. The objectives were: i) to evaluate the present formulae, ii) explore variable importance, iii) formulate a stability model, iv) extend the current datasets and v) explore a new model for LCS. The literature points to an increasing understanding of the initiation of damage of LCS and recent exploration of the shear stress-induced erosion (van Rijn, 2019). Assessment of two existing models (Kramer, 2006 and …

Maximum Coverage Facility Location Drone Routing Problem With Multiple Trip Stops, Marie Roza

Civil and Environmental Engineering Undergraduate Honors Theses

Integer linear optimization can be used to formulate routing problems as models to find optimal solutions given a set of inputs and constraints. In this research, Chauhan et al.'s publication, "Maximum coverage capacitated facility location problem with range constrained drones," is expanded upon by modeling a facility location problem with two-to-one drone deliveries. The model analyzes a set of potential facilities that are available to meet the demands of a set of demand points. The drone delivery routes are modeled with the assumption that each opened facility is assigned one drone that can fulfill up to two demand points’ demands …