Thermodynamics Commons^™

3d Fe Modelling Of Die Stress And Wear In Non-Isothermal Forging Of Ti–6al–4v Turbine Blade, Shiyuan Luo, Dahu Zhu, Lin Hua, Dongsheng Qian, Sijie Yan

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Methanol And Dimethyl Ether From Renewable Hydrogen And Carbon Dioxide: Alternative Fuels Production And Life-Cycle Assessment, Michael J. Matzen, Yaşar Demirel

Yaşar Demirel Publications

In this work we investigate two renewably based alternative fuels; methanol and dimethyl ether. The ultimate feedstocks for production are wind-based electrolytic hydrogen and carbon dioxide captured from an ethanol fermentation process. Dimethyl ether production was modeled in ASPEN Plus using a previously simulated methanol production facility. The facilities use 18.6 metric tons (mt) of H₂ and 138.4 mt CO₂ per day. Methanol is produced at a rate 96.7 mt/day (99.5 wt%) and dimethyl ether is produced at a rate of 68.5 mt/day (99.6 wt%). A full comparative life-cycle assessment (cradle-to-grave) of both fuels was conducted to investigate …

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Maximizing Orc Performance With Optimal Match Of Working Fluid With System Design, Kirtipal Barse, Michael Mann

Chemical Engineering Faculty Publications

This article compares constrained system design to non-constrained system design for the basic Organic Rankine Cycle (ORC). The 12 working fluids studied include eight dry-type, three isentropic, and one wet-type fluids. The ORC model was developed using Aspen HYSYS® and validated with data obtained from the literature. The constrained design compared the performance of working fluids for a fixed heat exchanger and turbine configuration. A non-constrained design was studied by altering the design specifications for the heat exchangers and turbine to match the working fluid. An energy and exergy analysis was performed using first and second law efficiency. The exergy …

Thermal Microfluidic Devices; Design, Fabrication And Applications, Benyamin Davaji

Dissertations (1934 -)

This thesis investigates the thermal actuation and temperature measurement methods in microfluidic devices. We designed and fabricated microfluidic devices with various functionalities such as: bio sensing, particle counting, microscale calorimetry, and cellular temperature measurement. All of these functionalities use thermal measurement methods. When quantitative measurements are required, the label-free nature of thermal measurement methods, along with its simple readout, make it a powerful candidate for lab on a chip and bio sensing/detection applications. In this work, thermal measurement methods are used to characterize bio-samples, measure concentrations, study thermal responses, and even perform particle cytometry. However, thermal measurement methods are known …

Thermal Transport Properties Of Dry Spun Carbon Nanotube Sheets, Heath E. Misak, James L. Rutledge, Eric D. Swenson, Shankar Mall

Faculty Publications

The thermal properties of carbon nanotube- (CNT-) sheet were explored and compared to copper in this study. The CNT-sheet was made from dry spinning CNTs into a nonwoven sheet. This nonwoven CNT-sheet has anisotropic properties in in-plane and out-of-plane directions. The in-plane direction has much higher thermal conductivity than the out-of-plane direction. The in-plane thermal conductivity was found by thermal flash analysis, and the out-of-plane thermal conductivity was found by a hot disk method. The thermal irradiative properties were examined and compared to thermal transport theory. The CNT-sheet was heated in the vacuum and the temperature was measured with an …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Hybrid Metal Oxide Cycle Water Splitting, Richard B. Diver Jr, Robert D. Palumbo, Nathan P. Siegel, James E. Miller

Other Faculty Research and Publications

Hybrid thermochemical water splitting cycles are provided in which thermally reduced metal oxides particles are used to displace some but not all of the electrical requirements in a water splitting electrolytic cell. In these hybrid cycles, the thermal reduction temperature is significantly reduced compared to two-step metal-oxide thermochemical cycles in which only thermal energy is required to produce hydrogen from water. Also, unlike the conventional higher temperature cycles where the reduction step must be carried out under reduced oxygen pressure, the reduction step in the proposed hybrid cycles can be carried out in air, allowing for thermal input by a …

High-Temperature, High-Pressure Viscosities And Densities Of Toluene, Aaron J. Rowane

Theses and Dissertations

High-temperature, high-pressure (HTHP) conditions are exemplified in ultra-deep petroleum reservoirs and can be exhibited within diesel engines. Accurate pure component hydrocarbon data is essential in understanding the overall behavior of petroleum and diesel fuel at these conditions. The present study focuses on the HTHP properties of toluene since this hydrocarbon is frequently used to increase the octane rating of gasoline and toluene occurs naturally in crude oil. In this thesis experimental densities and viscosity are presented to 535 K and 300 MPa extending the database of toluene viscosity data to higher temperature than previous studies. The data is correlated to …

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Unique Characterization Of Materials With Memory, John Murrough Golden

Articles

In general, materials with linear memory constitutive relations are characterized by a relaxation function. This leads to a situation where the free energy for most materials with memory is not unique. There is a convex set of free energy functionals with a minimum and a maximum element. An alternative procedure is proposed which characterizes a material by the kernel of the rate of dissipation functional. Using some recent results, we find that a unique free energy and relaxation function may then be deduced. An example is given for discrete spectrum materials. Also, the new results are used to show that …

Prediction Of Vapor/Liquid Equilibrium Behavior From Quantum Mechanical Data, Marshall J. Gnap

Williams Honors College, Honors Research Projects

MOSCED (Modified Separation of Cohesive Energy Density) is a particularly attractive model for activity coefficients because it offers intuitive insights into how to tune solvent-solute interactions to achieve optimized formulations. Unfortunately, only 133 compounds have been characterized with the MOSCED method. Furthermore, there is no convenient method for extending MOSCED predictions to new compounds. The hypothesis of the present research is that the surface charge density of a molecule, once normalized over the molecule surface area, provided graphically by a σ-profile from density functional theory (DFT) computations, can be used to estimate the parameters used in the MOSCED model. DFT …