Thermodynamics Commons^™

Effect Of Inter Electrode Distance On Electrochemical Mineralization Of Calcium Carbonate In Mildly Acidic Environments, Irene Walker, Ivy Wu, Steven Decaluwe, Robert Bell, Kerry Rippy

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The effect of inter electrode distance (IED) on electrochemical mineralization in a parallel plate cell with a stainless-steel working electrode is presented. Three IEDs were tested, 6.5 mm, 15.5 mm, and 22.0 mm, for their water reduction effectiveness to create a region of local alkalinity that stimulates calcium carbonate precipitation in mildly acidic conditions. Chronoamperometry at -1.6 V for 30 minutes with ex-situ optical microscopy and scanning electron microscopy (SEM) were used. At the smallest IEDs, crystal clusters formed in growth-favored regimes as compared to the largest IED, where nucleation dominated, leading to encasement of the SS mesh. Rapid precipitation …

Theoretical And Experimental Investigation Of Liquid-Liquid Phase Separation: Characterizing Elastin-Like-Polypeptides, Adam D. Quintana

Chemical and Biological Engineering ETDs

This dissertation develops and validates a semi-empirical Flory–Huggins-based interaction model, combined with Cahn–Hilliard simulations, for predicting multi-component liquid–liquid phase separation (LLPS) in elastin-like polypeptide (ELP) systems. Equilibrium droplet compositions, measured using a PDMS-based microfluidic device, enabled direct parameterization of interaction coefficients. The model was applied to generate phase diagrams and assess composition dependence in ternary mixtures. Cahn–Hilliard simulations were conducted to explore potential phase morphologies under different interfacial conditions. Multi-component Lattice Boltzmann simulations were implemented to model droplet morphology evolution under varying interfacial and diffusive parameters, reproducing experimentally relevant morphologies. A three-phase wetting study revealed conditions for selective wetting and …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Statistical Investigation Of Gypsum Crystallization Kinetics, Azmain A. Akash

LSU Master's Theses

Gypsum, a naturally occurring mineral salt, is frequently encountered in industrial processes such as seawater desalination and power plant cooling. Over the years, significant effort has been devoted to controlling the crystallization of gypsum through various chemical approaches, including acidification, chelating agents, and antiscalant polymers. Nevertheless, the cost associated with chemical treatments may be reduced by incorporating physical operational strategies to complement chemical methods in regulating gypsum crystallization.

This study systematically examines the comparative roles of chemical and physical entropy in the gypsum crystallization process to elucidate their respective influences on gypsum growth kinetics. Chemical entropy is manipulated by adjusting …

Numerical Modelling And Co-Optimization Of Gasoline Fuels For Gasoline Compression Ignition Using Multi Component Approach, Ashwin Karthik Purushothaman

Dissertations, Master's Theses and Master's Reports

Future mobility is expected to rely on a broad spectrum of powertrain technologies, including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), fuel cell electric vehicles (FCEVs) and traditional internal combustion engine (ICE) vehicles. Despite the shift toward electrification, internal combustion engines are projected to remain a key component of future powertrains, either as the primary power source or as range extenders to generate electricity in hybrid systems. As such, significant research efforts continue to focus on enhancing the efficiency and reducing the emissions of ICEs to meet increasingly stringent regulatory and environmental targets. Gasoline compression ignition (GCI) has been …

Membrane Reactor Modeling And Optimization For Hydrogen Production, Ayooluwa Tomiwa Akintola

Graduate Theses, Dissertations, and Problem Reports (ETD)

There has been an ongoing trend toward cleaner fuels for more environmentally benign forms of energy generation. Recently, hydrogen has been identified as a clean fuel for energy generation. However, the most established, efficient, and widely utilized technique for producing hydrogen remains the steam methane reforming (SMR) in the presence of catalyst. Unlike other fossil fuels, utilizing methane from natural gas in an SMR process to produce hydrogen emits less, but yet a notable sum of carbon dioxide. Furthermore, the endothermic nature of SMR reactions imply that there is a high energy requirement to obtain a substantial amount of hydrogen …

Fabrication And Performance Of Scalable Bio-Engineered Porous Layers For Efficient Co2 Capture, Mary Sharon Rose Bondugula

Theses and Dissertations

This dissertation addresses the critical challenge of mitigating climate change by advancing CO2 capture technologies. As global CO2 emissions continue to rise, effective methods for capturing and separating CO2 from industrial processes are essential to combat climate change. Existing CO2 capture systems, such as Pressure Swing Adsorption (PSA) and Temperature Swing Adsorption (TSA), often rely on packed bed designs that face limitations, including poor heat and mass transfer, slow gas diffusion, and low thermal conductivity, reducing their efficiency. To overcome these challenges, this dissertation explores innovative solutions by developing advanced adsorbent coatings and scalable bed configurations.

This research begins by …

Smart Manufacturing Of Cement: From Lab-Scale Simulation And Testing To Industry-Scale Deployment., Juan David Tabares Tamayo

Electronic Theses and Dissertations

Cement kilns are controlled by experienced process operators who follow experience-based industry guidelines using data collected and fundamental knowledge. The manufacturing process, which is equipped with sensors and equipment, transfers data/information to the operators to aid standardized decision-making operations. In contrast, companies have used such data to develop and implement digital solutions for predictive control systems; in effect, FLSmidth and Rockwell Automation. However, despite the availability of automated control systems and investigation in automation for process monitoring and optimization, opportunities to radically optimize cement manufacturing are still abundant and in need of implementation. Therefore, this research developed simulation models and …

Improving Static Cold Storage Life Of The Human Heart Before Transplant, Juan Sebastian Rodriguez Paez

Theses and Dissertations

Organ storage and transportation are critical steps for the success of organ transplantation. Static cold storage (SCS) of hearts for heart transplantation (HTx) remains the standard approach. However, SCS may involve damage to the tissue resulting from extended hypothermic preservation, potentially affecting organ viability. More over, the temperature distribution on and within the heart is unknown during heart transplantation. Therefore, there is an interest to study different stages of the heart transplantation process towards determining the 3D temperature distribution on and within the heart. There could be a possibility of having a hypothermic injury in different parts of the heart …

Research Of The Influence Of Physical And Chemical Properties Of Coal On The Gasification Process Using The Example Of Angren Brown Coal, Murodjon Mamitbekovich Kavkatbekov, Rakhimzhan Pachekhanovich Babakhodzhaev

Technical science and innovation

The influence of the properties of Angren brown on the process of layered gasification was studied. The dependence of the calorific value of the resulting gas on the quality characteristics of coal when using air as a gasifying agent has been established. Methods are shown for increasing the calorific value of gas obtained during the gasification process when using coal with different moisture content and different fractional composition. The features of technological processes in the reaction zones of a laboratory gas generator have been studied. Based on generally accepted methods, the volume fractions of flammable components, as well as the …

Mathematical Modeling Of Coupled Heat And Mass Transfer In Metal-Hydride Hydrogen Storage Systems, Muhammad Hasnain

College of Graduate Studies: Theses & Dissertations

As a promising clean energy carrier hydrogen has recently gained significant interest, but its efficient and safe storage is a major challenge. Compared to the gaseous state and liquid state, metal hydrides (MH) offer a potentially more effective storage approach for hydrogen. However, the main challenge in this approach is the low thermal conductivity of the MH bed that leads to low heat transfer and ultimately to higher charging and discharging times. The purpose of this work is to develop an in-house comprehensive heat and mass transfer model for hydrogen sorption in MH reactors to simulate the dynamic behavior of …

Hydrodynamics Of Drops And Particles Driven By Marangoni And Diffusiophoretic Forces, Subramaniam Chembai Ganesh

Dissertations and Theses

This study investigates the hydrodynamics of particles and drops driven by forces generated by an asymmetrical physical and chemical surrounding environment. In the first part, a novel colloidal motor design driven by surface tension forces is proposed, utilizing an active Janus particle encapsulated in an immiscible liquid drop to form a compound drop/particle. Marangoni forces induced by asymmetric solute adsorption at the liquid-liquid interface of the drop propels the compound system. The propulsion speeds of the motor are analyzed for various relative sizes and configurations of the Janus particle and the encapsulating drop and the effects of varying the transport …

Numerical Modeling Of Thermal Runaway In Lithium-Ion Batteries Using Decomposition Kinetics And Inter-Cell Contact Resistance, Shehzad Khan

College of Graduate Studies: Theses & Dissertations

Lithium-ion batteries (LIBs) are central in numerous high-demand applications due to their high energy density and prolonged cycle life. Despite these advantages, their susceptibility to thermal runaway (TR) poses a significant safety risk, with the potential for catastrophic failures. This study focuses on the thermal behavior of prismatic lithium-ion cells, using a finite volume-based partial differential equation (PDE) solver developed in MATLAB and JULIA to model TR behavior. This solver accurately simulates transient behaviors, convection, diffusion, and source terms across various coordinate systems. By engaging in a series of increasing complex case studies, this research aims to identify the critical …

Data-Driven Modeling Of Oxygen Kinetics In La0.6sr0.4co0.2fe0.8o3−Δ (Lscf) For High-Temperature Reduction Of Co2 In An Electrolysis Cell, Ferron Campbell

Graduate Theses, Dissertations, and Problem Reports (ETD)

Electrolysis systems are critical to several societal applications, particularly energy storage and conversion. Developing these systems requires a detailed knowledge of the chemistry and thermodynamics of the materials used in the electrolysis cell. This work focuses on using embedded scientific machine learning as an efficient way to build an interpretable model for the reaction and transport kinetics in the LSCF electrode, whose performance directly influences the electrolysis system’s performance. The models developed in this study are trained using the publicly available machine learning package, FoKL-GP. This package incorporates a robust Gibbs sampler that employs a forward variable selection process to …

Heat Transfer From Plates, Leanza Trevino

Chemical Engineering Undergraduate Honors Theses

The purpose of this honors thesis is to create an experiment for the CHEG Lab I course. This is a continuation of work done by Alexa Moreno. She created an experiment to model free convection of a horizontal plate. In this report, free and forced convection of a vertical and horizontal plate, respectively are modeled. This report explains the motivation for creating this heat convection experiment, the results of performing the experiment, and provides recommendations for future work on this experiment. Lab handouts are included in the Appendix.

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Attrition Study Of Copper-Supplemented Iron-Based Oxygen Carrier For Chemical Looping Combustion, Neng Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Chemical looping combustion (CLC) is a promising technology that can mitigate the carbon emissions for power generation. The cost of oxygen carriers (OCs) impedes the scale up of CLC. Compared to synthetic iron-based OCs, red mud (RM), an abundant iron-based solid waste from industry, is a cost-effective choice due to its intrinsic inclusion of both inert and catalytic phases that are crucial for CLC. It was anticipated that the addition of copper oxide to RM using a mechanical mixing method that can be easily scaled up would enhance both reactivity and oxygen transport capacity (OTC), and the heat of reaction …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Techno-Economic Analysis And Optimization Of Hydrogen And Mechanical Energy Storage Systems, Pavitra Senthamilselvan Sengalani

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing significance of renewable energy sources is thrusting the load cycling of fossil-fueled power plants (FFPP), designed to operate under nominal-load conditions. Integration of energy storage systems (ESS) with the FFPPs such as hydrogen energy storage (HES) and mechanical energy storage facility such as compressed air energy storage (CAES) shows the potential to minimize the levelized cost of electricity during high demand scenarios and also minimize the negative impacts of off-design FFPP operation. The deployment of energy storage facilities at the FFPP level have considerable potential advantages as they can be exploited within the existing equipment items and facilities …

Molecular Understanding Of Zwitterions And Quantum Computing For Sustainability, Manh Tien Nguyen

Theses and Dissertations--Chemical and Materials Engineering

The sustainable development of society needs sustainable energy solutions and the mitigation of greenhouse gas emissions. One key subject in this area is the development of safe and efficient ion-based batteries. Moreover, CO₂ capture is a crucial pathway in mitigating emissions from the combustion of fossil fuels. Ongoing efforts are to improve both technologies' safety and efficiency. This thesis presents our efforts to conduct computational research on understanding advanced zwitterionic electrolytes and CO₂ capture. Chapters 2-4 illustrate the computational research to understand ionic solvation in zwitterionic electrolytes. Solid-state electrolytes are essential for safer batteries. While solid polymer electrolytes …

Free Convection Heat Transfer From Plates, Alexa Moreno

Chemical Engineering Undergraduate Honors Theses

The purpose of this honors thesis is to create an experiment for the CHEG Lab I course. This report explains the motivation for creating this heat convection experiment, the results of performing the experiment, and provides recommendations for future work on this experiment. Multiple experiments were performed to assess materials and parameters to be investigated. It was determined that a 0.5” plate has smaller percent error and accommodates for the desired timeframe for a Lab I experiment compared to the first plate used (1.5” thickness). Recommendations for expanding on this project include adding experiments using vertical geometry for heat convection …

Development Of Advanced Models For Pre-Ignition Prediction In Gas Engines And Analytical Model For Wallfilm Evaporation, Ankith Ullal

Dissertations, Master's Theses and Master's Reports

Ever-changing regulations aimed at improving efficiency and reducing harmful emissions have resulted in many power-generation device (engine) manufacturers to adopt new strategies. Computer simulation of these new strategies of power generation requires more accurate and higher fidelity modelling tools. In the present study, two such models are developed. The first model deals with pre-ignition phenomena driven by lubricant (lube) oil in natural gas engines and the second model is relevant to prediction of wallfilm evaporation by employing analytical solutions to transport governing equations for boundary layers.

Pre-ignition in engines has been the subject of current research with the advent of …

Advanced Process Modeling And Optimization Of Amine-Based Carbon Capture Process, Paul Jide Terhemba Akula

Graduate Theses, Dissertations, and Problem Reports (ETD)

With the rise of carbondioxide (CO2) concentration in the atmosphere to more than 400 parts per million (ppm), research efforts have been focused on achieving net-zero carbon emission technologies. Post-combustion CO2 capture (PCC) is a key strategy in reducing CO2 emissions. Amine-based CO2 capture is the baseline technology for retrofitting existing power stations. However, the integration of amine-based PCC technology with power plants to reduce greenhouse gas emissions incurs a high energy penalty, decreasing a powerplant’s efficiency by about 23 percentage points. Understanding the capture plant dynamics plays an important role in its technical and economic performance. Rigorous models are …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Experimental Heat Transfer Investigations Of A Double Pipe U-Tube Heat Exchanger Equipped With Twisted Tape And Cut Twisted Tape Internals, Raj Kumar Nayak Maloth, Glen Cletus Dsouza, Swarna Mayee Patra

Mechanical and Materials Engineering Publications

For several decades, the use of heat exchangers for both heating and cooling applications has been established in industries ranging from process to space heating. Out of the various types of heat exchangers, U-tube heat exchangers are preferred owing to their abilities to handle larger flowrates and their simplicity in construction. U-tube exchangers are often equipped with innards of various forms which facilitate higher heat transfer rates and thermal efficiencies. Although higher heat transfer rates have been established with the addition of internals, there is a lack of coherence on the underlying complex physical phenomena such as heat transfer boundary …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Graphical Design And Analysis Of Mass Exchange Networks Using Composition Driving Forces, Nessren Mohamed Farrag, Dina Ahmed Kamel, Ayat Ossama Ghallab, Mamdouh Ayad Gadalla, Mai Kamal Fouad

Chemical Engineering

Pinch analysis is a methodology for minimizing energy and mass consumption in different industries. It has been widely applied for more efficient processes. This study presents a new graphical-approach to analyze and design Mass Integration (MI) and exchange networks that follows Pinch principles to guarantee maximum mass recovery with minimum losses. This technique uses the composition driving forces in network representation as it rules the mass transfer between streams. The proposed approach can be applied on both existing mass networks as well as new ones. This graphical representation a visual descriptive design tool to describe and explain the details of …

Understanding Absorption, Supersaturation, And Drug Activity In Solution: Working Towards Developing A More Biorelevant Media, Freddy Arce

Theses and Dissertations--Pharmacy

With the looming dominance of poorly water-soluble chemical entities within the pharmaceutical pipeline, the pharmaceutical industry has leaned on the use of supersaturating drug delivery systems (SDDSs) to achieve efficacious concentrations within the gastrointestinal fluids. SDDSs aim to achieve concentrations in solutions greater than the solubility of the lowest energy crystalline form. However, the generation of supersaturated solutions of active pharmaceutical ingredients (APIs) creates a strong crystallization potential, which is undesirable.

In product development, supersaturating products often fail in Phase I and Phase II clinical trials due to poor oral bioavailability and a lack of in vivo efficacy. Pre-clinical testing …

Testing The Effectiveness Of Various Fabrics For Use In Protective Face Coverings, Isaac Daley

Williams Honors College, Honors Research Projects

Facemask requirements have been heavily implemented as a result of the COVID-19 pandemic. The purpose of this study was to test various fabrics that could be used in face coverings and determine which materials are best for reducing virus transmission rates. Of the seven fabrics tested, five were conventional home-use fabrics and the other two were surfaces modified with hydrophobic organosilanes. Wettability and droplet adherence tests were performed on each material. The materials that performed the best were decyltrichlorosilane (DTS) modified cotton, perfluorotrichlorosilane (FTS) modified cotton, and polyester. Contact angles for water droplets on these fabrics were 106°, 93°, and …

Dynamic Modelling And Control Of Grid-Level Energy Storage Systems, Sai Pushpitha Vudata

Graduate Theses, Dissertations, and Problem Reports (ETD)

The focus of this work is on two energy storage technologies, namely pumped storage hydroelectricity (PHS) and secondary batteries. Under secondary battery technologies, two potential technologies for grid-scale storage, namely high-temperature sodium-sulfur (NaS) battery and vanadium redox flow battery (VRFB), are investigated. PHS is a largescale (>100 MW) technology that stores and generates energy by transporting water between two reservoirs at different elevations. The goal is to develop a detailed dynamic model of PHS and then design the controllers to follow the desired load trajectory accurately with high efficiency. The NaS battery and VRFB are advanced secondary batteries which …