Thermodynamics Commons^™

Numerical Characterization Of The Flow Field And Heat Transfer Inside The Receiver Of A Parabolic Trough Solar Collector Carrying Supercritical Co2, Samad Gharehdaghimollahajloo

UNLV Theses, Dissertations, Professional Papers, and Capstones

The aim of this research is to provide a detailed numerical analysis of flow field and heat transfer inside the heat collecting element of a parabolic trough collector. The parabolic trough collector is used as the boiler in a direct Super Critical Carbon Dioxide (S-CO2) Brayton cycle.

A single collector is modeled and analyzed with different inlet conditions. The working fluid is supercritical since its pressure is increased to above critical pressure in the compressor while its temperature reaches 300 °C after passing through the recuperators and before entering the solar field. For the first time, this research considers both …

3d Fe Modelling Of Die Stress And Wear In Non-Isothermal Forging Of Ti–6al–4v Turbine Blade, Shiyuan Luo, Dahu Zhu, Lin Hua, Dongsheng Qian, Sijie Yan

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Thermal Transport Properties Of Dry Spun Carbon Nanotube Sheets, Heath E. Misak, James L. Rutledge, Eric D. Swenson, Shankar Mall

Faculty Publications

The thermal properties of carbon nanotube- (CNT-) sheet were explored and compared to copper in this study. The CNT-sheet was made from dry spinning CNTs into a nonwoven sheet. This nonwoven CNT-sheet has anisotropic properties in in-plane and out-of-plane directions. The in-plane direction has much higher thermal conductivity than the out-of-plane direction. The in-plane thermal conductivity was found by thermal flash analysis, and the out-of-plane thermal conductivity was found by a hot disk method. The thermal irradiative properties were examined and compared to thermal transport theory. The CNT-sheet was heated in the vacuum and the temperature was measured with an …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Modeling Of Spallation Phenomenon In An Arc-Jet Environment, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles, while entering the planetary atmosphere, experience high loads of heat. Ablative materials are commonly used for a thermal protection system, which undergo mass removal mechanisms to counter the heat rates. Spallation is one of the ablative processes, which is characterized by the ejection of solid particles from the material into the flow. Numerical codes that are used in designing the heat shields ignore this phenomenon. Hence, to evaluate the effectiveness of spallation phenomenon, a numerical model is developed to compute the dynamics and chemistry of the particles. The code is one-way coupled to a CFD code that models …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

Fuel Composition Analysis Of Endothermically Heated Jp-8 Fuel For Use In A Pulse Detonation Engine, Eric A. Nagley

Theses and Dissertations

Waste heat from a pulse detonation engine (PDE) was extracted via zeolite catalyst coated concentric tube-counter flow heat exchangers to produce supercritical pyrolytic conditions for JP-8 fuel. A sampling system and method were developed that enabled samples of reacted fuel to be extracted during steady state operation. Samples were taken over a range of heat exchanger exit temperatures from 820 K (1016° F) to 940 K (1232° F). Offline analysis of liquid and vapor fuel samples indicated fuel decomposition via typical pyrolytic reaction pathways. The liquid analysis showed conversion of parent fuel components with formation of unsaturates (aromatics and alkenes) …

Cycle Performance Of A Pulse Detonation Engine With Supercritical Fuel Injection, Timothy M. Helfrich

Theses and Dissertations

Pulse detonation engines (PDE) rely on rapid ignition and formation of detonation waves. Because hydrocarbon fuels are composed typically of long carbon chains that must be reduced in the combustion process, it would be beneficial to create such reduction prior to injection of fuel into the engine. This study focused on PDE operation enhancements using dual detonation tube, concentric-counter-flow heat exchangers to elevate the fuel temperature up to supercritical temperatures. Variation of several operating parameters included fuel type (JP-8, JP-7, JP-10, RP-1, JP-900, and S-8), ignition delay, frequency, internal spiral length, and purge fraction. To quantify the performance, four key …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

A Shock Tube Study Of Aerodynamic Heating Of Gaps In A Cylinder Subjected To Supersonic Cross Flow, Douglas D. High

Theses and Dissertations

The effects of localized aerodynamic heating in cylinder expansion gaps positioned in cross flow were investigated in a shock tube. For this study, Mach number and Reynolds number were varied from 1.04 to 1.38 and 5 x 105 to 9 x 105, respectively. The cylinder was instrumented with quick response time thermocouples positioned on the surface of the cylinder, the wall of the gap, and the gap floor. Gap aspect ratios varied from 1.23 to 3.69. Pressure gauges were used to measure wave shock speeds, pressure ratios, and transient pressure conditions. Surface temperatures were measured and converted to heat fluxes …

Thermal Compatibility Analysis Of The Passive Damping Treatment Proposed For The Space Shuttle Remote Manipulator System (Srms), Mahesh Chowdhary

Mechanical & Aerospace Engineering Theses & Dissertations

The NASA Space Shuttle Remote Manipulator System (SRMS), due to its long reach and light weight construction has significant structural flexibility. Thus any routine use of SRMS often results in large amplitude oscillations with long settling time. A passive damping technique utilizing a constrained viscoelastic layer damping treatment has been proposed to augment the active control of these oscillations in order to enhance the system stability and the end effector positional accuracy. This thesis concerns with the thermal compatibility analysis of the proposed damping treatment. The necessity for thermal compatibility analysis arises from the fact that acceptable damping performance of …

Evaluation Of Equilibrium Turbulence For A Hypersonic Boundary Layer At Nonadiabatic Wall Conditions, Cindy W. Albertson

Mechanical & Aerospace Engineering Theses & Dissertations

This paper presents an experimental study to characterize the compressible turbulent boundary layer produced along a flat plate in the NASA Langley 8-Foot High Temperature Tunnel and determine the test conditions necessary to achieve equilibrium turbulence. In addition, the present study extends the data base for equilibrium compressible turbulent boundary layers over quasi-isothermal walls which are far from the adiabatic wall temperature. The measurements consist of pilot pressure, static pressure, and total temperature distributions in the boundary layer. A flat plate measuring 9.7 feet long and 4.3, feet wide was used for the study to provide a naturally turbulent boundary …