Process Control and Systems Commons^™

Fuzzy Logic-Based Decision Support System For Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

In the context of Industry 4.0, predictive maintenance enhances operational efficiency by optimizing processes, minimizing downtime, and improving cost-effectiveness. However, implementing predictive maintenance requires a systematic approach due to its complexity. This study collected expert input from 15 food and beverage manufacturing industries located in Dar es Salaam, Tanzania, using a purposive sampling technique. Six representatives were selected from each industry, and their opinions were analyzed using MATLAB 7.6 through a fuzzy logic inference system. The analysis focused on key factors influencing Industry 4.0 technology adoption for predictive maintenance, including adoption intention (strategic decision, equipment data, perceived benefit) and perceived …

Wet Gas Metering Performance Using Conventional Flow Measurement Devices, Vitali Mwinyi

Tanzania Journal of Engineering and Technology (TJET)

The demand for and production of natural wet gas from wells has significantly risen in recent years. Although natural gas liquids hold substantial value in the oil and gas market, their presence in wet gas adversely affects gas metering, leading to overreading during measurement. A comprehensive study has been undertaken to formulate and enhance correlations for rectifying overreading in wet gas metering. Nevertheless, most current correlations are designed for horizontal configurations of traditional meters. Mitigating this constraint is crucial to consider the impact of gravity on pressure loss in vertically oriented systems. This study seeks to evaluate the efficacy of …

Energy Optimal Coverage Motion Trajectory Generation Using A Fourth-Order Motion Profile, Mathias Halinga

Tanzania Journal of Engineering and Technology (TJET)

Industrial machines are widely used in manufacturing sector to manufacture several products to meet customer demands. Most of these industries runs all the time throughout a day leading to high operating cost. To cut costs and satisfy customer demand for precise products, industrial machines’ motion generation is important in improving machine motion precision while using less energy. This study presents a coverage motion energy optimization which is generated by linear interpolation of each segment described by the fourth-order motion profile. The phase changes in the profile are attained with continuity of machine kinematic limits jerk, acceleration, and velocity, which are …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Cost Estimation Proxy Models For Economic Evaluations In Petroleum Projects: A Case Study From The Onshore Gas Field In The Southern Coastal Tanzania Basin, Fulmence Kaborogo

Tanzania Journal of Engineering and Technology (TJET)

Petroleum economic evaluation involves estimating revenues from forecasted production profiles and field costs including capital expenditures (CAPEX), drilling expenses (DRILLEX), and operating expenses (OPEX). The existing cost-estimating tool requires several inputs making it time-intensive and difficult to use with few data during the early stages of projects. Majority of the previously developed time saving cost estimations proxy models rely on unrealistic assumptions that include uniform operational costs for different fields with a different number of wells, casings, and drilled depths. This work focused at developing proxy models that consider the variability of the development costs with different parameters. The developed …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Employment Of Intelligent Predictive Maintenance On Thermal Power Plant Component Parts Taking Condenser Vacuum As A Case Study, Titus Ajewole

Tanzania Journal of Engineering and Technology (TJET)

This work proposes deployment of machine learning in the maintenance of individual constituent parts of steam power plant assemblages. With the condenser vacuum of a steam turbine (in a six-turbine plant assemblage) taken as a case study, information on the past operating parameters of the selected plant component was used to forecast its future working condition. Based on Exponential Gaussian Process of Regression, a model was developed, trained using the diachronic operational data, and employed in determining the future. A quantitative evaluation was employed to provide the distribution of the test values of the data about the lines of regression, …

Factors Influencing Total Productive Maintenance Implementation For Thermal Generation Plants, Ismail W. R. Taifa Dr

Tanzania Journal of Engineering and Technology (TJET)

This study accepts that the technical and administrative factors can amplify effective total productive maintenance (TPM) implementation at thermal generation plants. It is noted that there is a limited number of studies that have attempted to understand the subject of TPM implementation in the energy sector. Noting this shortcoming, the authors thought it crucial to generate empirical evidence on the factors influencing effective TPM implementation for thermal generation plants, with evidence from gas-fired plants. A sample of 88 respondents was selected and consulted. Data were collected through questionnaires and analyzed quantitatively by inferential statistics and qualitatively through thematic analysis using …

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

Fermentability Of Concentrated Sulfuric Acid Hydrolyzates From Aspenwood And Pinewood, Kando Janga

Tanzania Journal of Engineering and Technology (TJET)

The fermentability of hydrolyzates derived from two-stage concentrated sulfuric acid hydrolysis of Trembling aspen (Populus tremula) and Scots pine (Pinus sylvestris) were investigated. Three types of hydrolyzates were produced at mild, moderate and high decrystallization severity conditions. Portions of each of the original hydrolyzates were concentrated by vacuum evaporation to increase the sugar fraction to simulate industrial applications. Both sets of hydrolyzates were fermented anaerobically using Saccharomyces cerevisiae ATCC 96581. After 23 hours of fermentation, complete glucose consumption was observed for all the original hydrolyzates, with no signs of inhibition. The ethanol yields from these hydrolyzates ranged from 68% to …

Thermodynamic Analysis And Optimization Of Organic Rankine Cycles Using 1-Butylpyridinium Tetrafluoroborate As A Geothermal Fluid, Kazemi Shabnam

Student Works (2020-2029)

Organic Rankine cycle (ORC) is a promising technology for electricity generation by utilizing heat sources at low to moderate temperature that ranges between 80-350° C. In the present work, an ionic liquid (1-butylpyridinium tetrafluoroborate, C9H14NBF4), a known green chemical and non-volatile compound with good thermal and chemical stability, significant heat capacity, low vapor pressure and a wide liquid temperature range (25 to 459 °C), is utilized as a geothermal fluid. Simulation and optimization were conducted for a basic organic Rankine cycle (basic ORC), a regenerative organic Rankine cycle (RORC) and a two-stage evaporative organic Rankine cycle (TSORC) by maximizing exergy …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Applied Control Strategies At A Cogeneration Plant, Joseph William Burns

Master's Theses

The purpose of this paper is to demonstrate the effectiveness of “classical strategies for dynamic control” on authentic cogeneration processes. These strategies are applied to several processes at the University of Connecticut’s cogeneration plant. Case studies of their applications are presented in this paper. Strategies that are applied include the following:

1) The classical SISO feedback structure

2) The First Order Plus Dead Time (FOPDT) process model

3) The Internal Model Control (IMC) correlations for PI controller tuning

4) Static feed forward with feedback trim

5) Cascade Control

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

A Mathematical Model And Simulation Of Natural Circulation Loop Thermalhydraulics, Nihad E. Daidzic

Aviation Department Publications

In this work, a simple, nonlinear, seventh-order mathematical model with lumped parameter analysis of the thermalhydraulic processes in a natural circulation steam boiler loop is presented. Digital simulation has been performed in order to predict open loop transients in severe accidental situations. Parts of the circulation loop such as the steam drum, downcomer, and riser were modelled separately on the basis of the integral balance equations. The two-phase flow in the steam drum and in the riser was modelled with the aid of a homogeneous-equilibrium, two-phase flow model. Special care was taken to ensure the stability of the numerical scheme, …