Electrochemical And Mechanical Evaluation Of Cellulose Acetate Electrolyte Films As A Function Of Polyetherimide And Polyethylene Glycol Additives For Supercapacitor Applications, Chase E. Golden

Chemical Engineering Undergraduate Honors Theses

Polymer electrolytes for supercapacitor applications require a balance between mechanical robustness and electrochemical performance. In this study, cellulose acetate (CA) films were modified with additives such as polyetherimide (PEI) and polyethylene glycol (PEG) to test how compositional changes influence mechanical performance, ionic conductivity, and electrochemical charge storage. Films were cast using phase inversion, soaked in a 1 M NaCl aqueous solution, and characterized using Fourier-transform infrared spectroscopy (FTIR), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and tensile testing. Films were also evaluated based on fluid uptake for insight into electrolyte retention.

Characterizations show that the addition of PEI increased ionic …

Molecular Origins Of Non-Frozen Water In Polyelectrolyte Brushes, Ali Dhinojwala, Saveen Jayaweera, Md Golam Kibria, George Mallinos

University Research

Polyelectrolyte brushes (PEBs) are promising coatings for reducing ice adhesion and regulating water freezing at interfaces, yet direct measurements of nonfrozen water retention at subzero temperatures remain scarce. Here, we investigate the freezing behavior of water confined in poly([2-(methacryloyloxy)ethyl]trimethylammonium) (PMETA) brushes with chloride, iodide, and sulfate counterions using a custom-built low-temperature attenuated total reflectance infrared spectroscopy system. Furthermore, we quantify the fraction of water that was present within the brush that does not freeze as well as the changes in polymer volume fraction within the brush as a function of temperature. Spectroscopic analysis of water vibrational modes reveals that PMETA …

Energy Efficient Windows Using Pvme, James S. Bronstrup

Williams Honors College, Honors Research Projects

This Honors Project aims to improve window energy efficiency using the thermoplastic polymer PVME (polyvinyl methyl ether), which displays temperature-dependent transparency that can be adjusted by mixing it with water and salt to reduce heat transfer through a window. The objective is to determine the optimal PVME water-salt ratios for placement inside a windowpane, evaluate energy savings compared to a traditional argon-filled window, and compare estimated costs. A small-scale model will test different concentrations for various climates, with heat transfer measured by temperature indicators via a LabQuest. Building on research by Yang Zhou at Nanyang Technological University, who used a …

Chemical Recycling Of Pet Plastic Waste, Charlie Parker, Benjamin Puga, Jake Verschoor

Materials Engineering

The growing accumulation of plastic waste, specifically polyethylene terephthalate (PET), has driven the need for more efficient and scalable chemical recycling methods. This study investigated the methanolysis of PET using zinc oxide (ZnO) nanoparticles as a catalyst and tetrabutylammonium chloride (NBu₄Cl) as an ionic liquid, aiming to reduce methanol consumption while achieving high PET conversion efficiency. ZnO nanoparticles were synthesized via wet chemistry and characterized using Dynamic Light Scattering (DLS), which showed an average particle size of 13.5 nm with a polydispersity index of 0.1556, indicating a moderately-high monodisperse distribution of particles sufficient for reactions. The main conversion product, dimethyl …

Biobased Acrylate Composites With Enhanced Strength For Additive Manufacturing, Nicole Wagner, Joseph Mcwherter

Engineering Faculty Articles and Research

With the expanding use of polymers in additive manufacturing, sustainable resins for use in vat photopolymerization are required to reduce their environmental impact. One promising approach to achieve this is to incorporate biobased fillers that replace the acrylates in photopolymer resins as ‘green’ alternatives. In this study, photopolymer composites consisting of a methacrylate resin with varying calcium carbonate powder content between 0 and 50 wt.% were investigated. A digital light processing technique was used to fabricate tensile test specimens for mechanical testing. Good printability, dimensional accuracy, and good interlayer adhesion were observed for composite resin formulations that incorporated calcium carbonate …

A Comprehensive Review Of Piezoelectric Pvdf Polymer Fabrications And Characteristics, Nadia Ahbab, Sidra Naz, Tian-Bing Xu, Shihai Zhang

Mechanical & Aerospace Engineering Faculty Publications

Polyvinylidene fluoride (PVDF) polymer films, renowned for their exceptional piezoelectric, pyroelectric, and ferroelectric properties, offer a versatile platform for the development of cutting-edge micro-scale functional devices, enabling innovative applications ranging from energy harvesting and sensing to medical diagnostics and actuation. This paper presents an in-depth review of the material properties, fabrication methodologies, and characterization of PVDF films. Initially, a comprehensive description of the physical, mechanical, chemical, thermal, electrical, and electromechanical properties is provided. The unique combination of piezoelectric, pyroelectric, and ferroelectric properties, coupled with its excellent chemical resistance and mechanical strength, makes PVDF a highly valuable material for a wide …

Effects Of Polyolefin Types On Catalytic Hydrocracking, Kenneth Jackson Seeber

Williams Honors College, Honors Research Projects

Plastic waste recycling has become an important conversation in the last couple of decades with pollution on the rise. One of the few ways to recycle plastics is by breaking these long-chained polymers down via catalytic processes. Due to many plastic products being a blend, it is imperative that any chosen catalyst that could be used for recycling should be able to handle different types of polymers. This paper discusses how tungsten carbide over silica (W_xC/SiO₂) catalyzes the degradation of a few selected polymers and polymer blends. From this research it was determined that W_{x …}

Precision Bottlebrush Polymers: Synthesis, Characterization, And Structure-Property Relationship, Nduka D. Ogbonna

LSU Doctoral Dissertations

Bottlebrush polymers, a type of non-linear polymer characterized by densely grafted side chains on a linear backbone, offer a versatile platform for material design due to their unique thermomechanical and rheological behavior. Addressing the grand challenge of achieving structural precision for bottlebrush polymers remains crucial because traditional disperse mixtures are plagued with batch variability, limiting our ability to control their functions, and correlate theoretical predictions with experiments. To date, narrow-dispersity bottlebrush polymers remain highly heterogeneous, as they are typically synthesized from disperse linear building blocks.

To address this longstanding challenge of structural heterogeneity in brush polymers, the primary objective of …

Mechanical Property Simulations Of Ploybenzimidazole Membranes., Blake Alexander Clark

Electronic Theses and Dissertations

This work explores mechanical properties of membranes made of polybenzimidazole utilizing molecular simulations. These simulations researchers to narrow down polybenzimidazole membrane compositions to viable candidates. These simulations are quicker than current purely experimental methods. The increase in throughput would be achieved by eliminating compositions that have unfavorable mechanical properties through preliminary simulation work before moving onto experimental methods. Determining polybenzimidazole membranes’ mechanical properties experimentally would, therefore, allow for researchers to speed up research in areas such as fuel cells and electrolyzers that make use of polybenzimidazole membranes. This study uses Materials Studio and the COMPASS III forcefield to perform these …

Experimental Evaluation Of Mesh Size In Physically Crosslinked Polymer Gels Using Dynamic Light Scattering, Duncan M. Hill

Honors Theses

Block copolymer gels are under consideration as drug delivery patches. Controlling and modeling the transport inside the gel is an important contribution to the successful delivery of pharmaceuticals. The diffusive transport of a solute – such as a therapeutic compound – within the gel can be described by the mesh size of the gel, which is defined as the distance between polymer chains. Existing experimental evaluations of mesh size do not work for block copolymer gels due to differences in the fundamental gel structure. As such, an experimental method of measuring mesh size of block copolymer gels using dynamic light …

Optimized Pi Compound Mixing Strategy, Cecilia Mainzer

Williams Honors College, Honors Research Projects

The project focuses on developing an optimal mixing strategy for a polyisoprene (PI) compound at the Goodyear Tire & Rubber Company. The aim is to optimize performance objectives of the compound. The project involved research, design iterations, mixing analyses, and performance evaluations, while adhering to engineering codes and standards.

The design process includes analyzing differences between two mixing technologies, intermesh and tangential rotors; altering mixing conditions; and exploring additional polymer systems and coupling technology of the compound.

Validation data confirms that the mixing technology and compound recipe meets all success metrics, including stiffness, hysteresis, adhesion, cure rate, and tear performance …

Removal Of Residual Stress In 3d Printed Polymers, Christian Jenkins

Williams Honors College, Honors Research Projects

This project aims to investigate the relationship between stress relaxation and the reduction of dimensional shrinkage and warping in 3D printed polymers produced through fused filament fabrication. The hypothesis suggests that residual stress in 3D printed structures results from factors such as temperature differences, molecular-level contributions, and rapid cooling, causing post-printing warpage and damage. To mitigate these issues, the project proposes annealing 3D printed polymers in a hot sandbath to allow stress relaxation without warping. The study will employ a Dynamic Mechanical Analysis (DMA) machine to assess mechanical properties of relaxed and unrelaxed samples, comparing their effectiveness. The project's timeline …

Elucidating The Mechanical And Transport Properties Of Lignin-Based Hydrogel Composites, Nicholas Gregorich

All Dissertations

The use of lignin in the fabrication of soft composites has become an emerging area of research in polymer science and polymer chemistry. These lignin-based materials present numerous benefits, notably, a reduction in the use of petroleum-based precursor, improved structural benefits to otherwise soft host polymers, as well as the inherent antimicrobial and antioxidant properties of lignin, making it suitable for biomaterials. Herein, we present two chemical reaction pathways of incorporating lignin that was fractionated and cleaned using the Aqueous Lignin Purification with Hot Agents (ALPHA) process into poly(vinyl alcohol) (PVA) hydrogel composites for aqueous-based separations. By leveraging the ALPHA …

Poly(Ether Imide)S: Synthesis And Properties, Rachel Price

Honors College Theses

The synthesis of strong polymers is crucial to the creation of heat-resistant, durable, and mechanically useful plastics that we use every day. Poly(ether imide)s are used in applications such as food service, aerospace, automotive, and many more. This thesis will discuss the synthesis and properties of these plastics to help express a larger understanding of these polymers.

Programming The Properties Of Branched Polymers Through Precision Architectures, Michael R. Dearman

LSU Master's Theses

The glass transition of branched polymers is determined by multiple structural parameters that dictate their inter- and intramolecular interactions, and ultimately, their molecular packing in the amorphous phase. Here we examined the impact of side chain length, backbone length, molecular weight composition, and topology on the glass transition behavior of bottlebrush polymers. Through examining precision bottlebrush polymer libraries (PBP, ĐSC = 1.0), we find the infinite molecular weight Tg is reached at a specific brush length after which the effect of the side-chain length dominates. Being a factor more dominant than the backbone, side-chain length affects the Tg of bottlebrush …

Application Of Sla 3d Printing For Polymers, Taylor Wilson

Williams Honors College, Honors Research Projects

Stereolithography is a type of 3D printing that allows liquid photopolymer resin to be cured into layers that make up a 3D object. Creation of such resins for these purposes can require a significant amount of time to test and develop, and commercial resins also require some amount of testing for printer settings before use. This paper reviews how stereolithography works, the materials used, and experimentation done to compare the resin properties to the determined curing times. Using several commercially available resins, varying base exposure and layer exposure times were used to determine the lowest possible curing time that gave …

Therapeutic Injectable Iron-Chelating Hydrogels, Debbie Campbell-Rance

Theses and Dissertations

ABSTRACT

Therapeutic Injectable Iron-Chelating Hydrogels for Improved Central Nervous System Regeneration

By

Debbie S. Campbell-Rance

A dissertation submitted in partial fulfillment of the requirements of the degree of Doctor of Philosophy at Virginia Commonwealth University 2021.

Director: Xuejun Wen, M.D., Ph.D., AIMBE Fellow, Alice T. and William H. Goodwin Jr. Endowed Chair Professor in Regenerative Medicine, Institute for Engineering and Medicine, Department of Chemical and Life Science Engineering

Severe traumatic brain and spinal cord injuries are major global public health and socioeconomic problems in terms of mortality and morbidity. Currently there are two main lines of treatment under development for …

Approaching Disorder-Tolerant Semiconducting Polymers, Xinwen Yan, Miao Xiong, Xin Yu Deng, Kai Kai Liu, Jia Tong Li, Xue Qing Wang, Song Zhang, Nathaniel Prine, Zhuoqiong Zhang, Wanying Huang, Yishan Wang, Jie Yu Wang, Xiaodan Gu, Shu Kong So, Jia Zhu, Ting Lei

Faculty Publications

Doping has been widely used to control the charge carrier concentration in organic semiconductors. However, in conjugated polymers, n-doping is often limited by the tradeoff between doping efficiency and charge carrier mobilities, since dopants often randomly distribute within polymers, leading to significant structural and energetic disorder. Here, we screen a large number of polymer building block combinations and explore the possibility of designing n-type conjugated polymers with good tolerance to dopant-induced disorder. We show that a carefully designed conjugated polymer with a single dominant planar backbone conformation, high torsional barrier at each dihedral angle, and zigzag backbone curvature is highly …

Establishing Independent Tunability Of The Mechanical And Transport Properties Of Polymer Gels, Lucas Rankin

Master’s Theses

Polymer gels can be used in the fabrication of materials for filtering liquid and gaseous media, solid-state electrolytes, and transdermal medical patches. This diverse range of applications primarily relies on the transport and mechanical properties of polymer gels. Both sets of properties have shown excellent tunability, but typically in a coupled fashion. Establishing the independent tunability of the transport and mechanical properties of polymer gels (using simple, cost-effective methods) is paramount if polymer gels are to be used to their full potential. Specifically, block copolymer gels self-assemble into organized nanoscale networks within the gel solvent, which allows for facile control …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Aging Of A Polymer Core Composite Conductor Under Combined Ozone And Temperature Conditions, James M. Middleton

Electronic Theses and Dissertations

The next generation High Temperature Low Sag Polymer Core Composite Conductors (HTLS PCCC) can experience harsh in-service environments including high temperature and highly concentrated ozone. In some extreme cases, it is possible that the conductors will experience temperatures of up to 180°C and ozone concentrations as high as 1% (10,000 ppm). Therefore, the primary goal of this research was to determine the most damaging aging conditions which could negatively affect the in-service life of the conductors. This included characterizing the aging in ozone and at high temperature of the HTLS PCCC hybrid composite rods and neat resin. It was found …

Plasma Processes And Polymers Special Issue On: Plasma And Cancer, Mounir Laroussi, Michael Keidar

Electrical & Computer Engineering Faculty Publications

During the last two decades, research efforts on the application of low temperature plasmas in biology and medicine have positioned nonequilibrium lowtemperature plasmas as a technology that has the potential of revolutionizing healthcare.[1,2] Low temperature plasmas can be applied in direct contact with living tissues to inactivate bacteria,[3] to disinfect wounds and accelerate wound healing,[4] and to induce damage in some cancer cells.[5–11]

Improving The Efficiency Of P3ht:Icba Organic Solar Cells By Modifying The Photoactive Solution Preparation Step, Matthew Blaine Samson

Electrical & Computer Engineering Theses & Dissertations

Organic solar cells (OSCs) are a promising alternative to conventional silicon solar cells. These organic devices offer the promise of facile low cost large scale solution based processing on lightweight, flexible, plastic substrates. At the present state of the technology, however, OSCs exhibit relatively low power conversion efficiencies. To improve these efficiencies, new materials are constantly being developed.

One such material is the fullerene indene-C₆₀ bisadduct (ICBA). When implemented in a poly(3-hexylthiophene-2, 5-diyl) (P3HT) : ICBA bulk heterojunction solar cell, these devices exhibit open circuit voltages exceeding 0.8 V, a value much higher than the devices made implementing phenyl-C …

Measuring Acoustic Attenuation Of Polymer Materials Using Drop Ball Test, Yi Zhang

Doctoral Dissertations and Master's Theses

Polymers are often used for vibration damping and energy absorption. The effect of a material in reducing the strength of sound waves traveling through it is called acoustic attenuation. In the past, attenuation has mostly been evaluated in the MHz frequency range, using a pulse generator and transmitting transducer as the wave source. However, most real acoustic activities occur at frequencies up to a few hundred kHz. Here, a simple drop ball mechanism is used to generate acoustic source waves in the kHz range, and the attenuation capacities of several solid materials are measured. The recorded waveforms substantially differ between …

Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa

Student Works (2010-2019)

In the present study, polymer electrolyte films composed of polyacrylonitrile (PAN) as a host polymer, ethylene carbonate (EC) as the plasticizer and lithium triflate (LiCF3SO3) and sodium triflate (NaCF3SO3) as dopant salts were prepared by the solution cast technique. Five systems of polymer electrolytes films have been prepared; these systems are the plasticized-PAN system i.e. PAN-EC system, two salted-PAN systems i.e. PAN-LiCF3SO3 and PAN-NaCF3SO3, and two plasticized-salted PAN systems i.e. PAN-EC-LiCF3SO3 and PAN-EC-NaCF3SO3. The pure PAN film was prepared as a reference. The ionic conductivity for each system is characterized using impedance spectroscopy. The room temperature conductivity of the pure …

Application Of The Thermal Flash Technique For Low Thermal Diffusivity Micro/Nanofibers, Michael T. Demko, Zhenting Dai, Han Yan, William P. King, Miko Cakmak, Alexis R. Abramson

College of Polymer Science and Polymer Engineering

The thermal flash method was developed to characterize the thermal diffusivity of micro/nanofibers without concern for thermal contact resistance, which is commonly a barrier to accurate thermal measurement of these materials. Within a scanning electron microscope, a micromanipulator supplies instantaneous heating to the micro/nanofiber, and the resulting transient thermal response is detected at a microfabricated silicon sensor. These data are used to determine thermal diffusivity. Glass fibers of diameter 15 mu m had a measured diffusivity of 1.21x10(-7) m(2)/s; polyimide fibers of diameters 570 and 271 nm exhibited diffusivities of 5.97x10(-8) and 6.28x10(-8) m(2)/s, respectively, which compare favorably with bulk …

Structure Property Relationships In Electron Donating Systems For Potential Photovoltaic Applications., Jonathan Moghal

Doctoral

Conjugated polymers are considered to be one-dimensional semiconductors. In conjugated polymers single and double bonds alternatively bond the carbon atoms along the polymer chain. The loosely bound electrons determine the electronic properties of conjugated polymers. In order to utilise the properties of conjugated polymers in terms of a photovoltaic (PV) device application an acceptor material must be added. The acceptor material used in this study is used in buckminsterfullerence (C60). C60 was selected for this purpose due to its size and the fact that it can accept up to six additional electrons. Ultrafast charge transfers from a conducting polymer onto …

The Effects Of Low Doses (1 To 500 Kilograys) Of 100-Kev Electrons On Four Polymers, Cynthia Anne Bradbury

Physics Theses & Dissertations

Commercial films of polyetherimide (PEI), polyetheretherimide (PEEI), polyethylene terephthalate (PET), and polycarbonate (PC) were exposed in vacuum to l 00-keV electron radiation to total absorbed doses of l, l 0, l 00, 300, and 500 kilograys. The concentration of radiation-generated radicals, as measured by electron paramagnetic resonance (EPR), increased by over an order of magnitude in all four polymers. Correspondingly, the intensity of the infrared absorption peaks increased uniformly for all doses. Solubility tests resulted in decreased solubility in all polymers. IR, EPR, and solubility suggest dehydrogenation of the aliphatic C-H and phenyl C-H sites. The data indicated that cross …

The Synthesis Of New Maleimide Addition Polymer Precursors, Richard B. Brown

Chemistry & Biochemistry Theses & Dissertations

1H-2,3-dimethylpyrrolo(1,2-a) benzimidazol-l-one (27) and 1H,9H- 2,3,7,8-tetramethyl-bispyrrolo(1,2-a:6,7-a')benzodiimidazo1-1,9-dione (32) have been synthesized from dimethylmaleic anhydride and o-phenylenediamine and 1,2,4,5-tetraaminobenzene, respectively. The presence of reactive olefinic double bonds in the synthesized compounds was of interest as a site for possible addition polymerization.

The synthetic route involved, in both cases, a simple nucleophilic substitution reaction between the diamine(or tetraamine) and the anhydride to form an intermediate amide-acid-amine which rapidly cyclized to the imide amine. The final ring closure required more rigorous conditions and occurred at melt reaction temperatures.