Synthesis Of Activated Carbon From Coconut Shell And Recycled Styrofoam Nanofiber For Water Filtration, Rahma Dani, Ismet Ismet, Leni Marlina, Rona Alisya, Muhamad Abel Kirana Aldi, Anggi Ludiansyah, Lintang Auliya Kurdiati, Meutia Kamilatun Nuha Ap Idjan, Agung Mataram, Muhammad Rama Almafie, Ida Sriyanti

Makara Journal of Science

Water pollution affects life sustainability; hence, several efforts have been exerted to overcome this problem. For ex-ample, nanofiber membrane technology is introduced to retain solutes while allowing only water molecules to pass through the system. Therefore, this study aimed to maximize the technology for water filtration using the electrospin-ning method by combining Styrofoam waste-based polymer with activated carbon from coconut shell waste (ACCS). The nanofiber diameter produced ranged from 590 nm to 610 nm with porous characteristics and without beads. The carbon content varied from 68.04% to 69.84%, according to the energy dispersive X-ray measurement, demonstrating the composite’s effectiveness. The …

Cellulose Materials For Drug Delivery Applications, Reham Mohamed

Mechanical Engineering Theses

Non-healing wounds are a growing global public health concern due to inadequate or ineffective therapeutic products available. Cellulose-based biopolymers are attractive wound dressing materials due to their biocompatibility, biodegradability, non-toxicity, and cost-effectiveness. This study aims to design and fabricate solid dosage formulations using carboxymethyl cellulose (CMC) and ethyl cellulose (EC) to facilitate multi-stage releases of phenytoin (PHT) and tetracycline hydrochloride (TCH) from plain carriers, fibers/films composites, and layer-by-layer fiber composites. Results from in vitro drug release assays demonstrated a time-dependent release up to 8 hours from PHT-loaded EC fibers, while TCH-loaded CMC films exhibited a rapid release within 5 minutes. …

Promotion Of Human Schwann Cell Proliferation Using Heparin/Collagen Coated Nerve Conduits, John Magness

Chemical Engineering Undergraduate Honors Theses

Often in the aftermath of an injury or surgery, the sense of touch and muscle control is lost in the affected area as nerves are damaged or severed and fail to grow back completely. The regeneration of the nerve cells can be promoted by treating the nerves with nerve conduits. Nerve conduits are hollow cylinders of bio-compatible materials that can be surgically implanted to the disconnected nerve to promote and direct the growth of nerves. The objectives of this research are to investigate the ability of nerve conduits treated with layer-by-layer coatings to promote the growth of Schwann cells, to …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Developing A Portable Prototype To Utilize An Electrospun Colorimetric Sensor For The Detection Of Trihalomethanes In Water, Amanda Svensson

Williams Honors College, Honors Research Projects

Trihalomethane (THM) detection in water is important due to the potential health effects caused by their presence, including increased cancer risk. A cheap, quick, and portable method of identifying THM concentration at the Environmental Protection Agency limit of 80 parts per billion (ppb) will improve detection and water treatment. Electrospinning was used to make nanofiber membranes using a 2.6 wt% polypropylene solution. These membranes were utilized in the Fujiwara reaction, which creates a color change in the presence of THMs, to detect the THM bromoform in water. The color intensity of the reaction was quantified for 250 and 80 ppb …

Correlation Of Electrospun Polyvinylpyrrolidone Fiber Mat Thickness With Basis Weight, Fiber Diameter, Pore Size Distribution, And Air Permeability, Leah Mcpherson

Williams Honors College, Honors Research Projects

This project developed correlations between electrospun polyvinylpyrrolidone fiber mat thickness, basis weight, fiber diameter, pore size, and air permeability. The hypotheses were thinner fibers produce thicker mats, pore size decreases with fiber diameter, pore size and permeability decrease as basis weight increases. Project results could be used for modeling or quality control purposes.

Fiber diameter distributions were analyzed using a Scanning Electron Microscope and FibraQuant 1.3 software. Four conditions were chosen for further study: 0.284 ± 0.104 µm, 0.379 ± 0.128 µm, 0.520 ± 0.138 µm, and 0.733 ± 0.177 µm. Lower PVP concentrations produced thinner fibers.

Sample thickness (nm) …

Construction Of Polyurethane Fabric Nanocomposites For Use In Resistance Temperature Detectors-Effect Of Polyurethane Concentration, Multi-Walled Carbon Nanotubes, And Oxidant, Jordan M. Shaffer

Williams Honors College, Honors Research Projects

Current resistance temperature detectors (RTDs) are rigid and create pressure points when used in contact with the human body. The current RTDs can also not be used in confined areas like the inside of a prosthetic. The research done for this paper explores the possibility of creating a soft fabric like RTD that can accurately measure temperature. This RTD could be used in medical devices, be placed in prosthetic legs, and be worn for a long period of time creating no discomfort for the user. Polyurethane scaffolds were created through an electrospinning process and multiwalled carbon nanotubes were adhered to …

Smart Fabrics For Colorimetric Detection, Breland Edwards

Undergraduate Research Posters

Due to the prevalence of chemical warfare, soldiers often carry chemical sensing devices, to warn of oncoming nerve agents. However, these devices are cumbersome. A lightweight, wearable chemical sensing fabric that doubles as a protectant against toxins would be beneficial. This fabric can be created by incorporating (1) organophosphate hydrolase, an enzyme capable of degrading organophosphates and releasing an acidic by product, and (2) polyaniline, a color changing polymer that changes from purple to green in the presence of acid, into nylon or polyvinyl alcohol nanofibers. The first step is to produce fabrics containing polyaniline and demonstrate that the fabrics …

Electrospinning Of S-B-S Triblock And S-I-S Triblock Copolymers For Use In Fuel Filtration, Kevin Houser

Williams Honors College, Honors Research Projects

The following research project looked into the potential of using nanofibers of syrene-isoprene-styrene triblock copolymer produced through the electrospinning process for the filtration of water out of fuel as well as a comparison of styrene-isoprene-styrene triblock to the styrene-butadiene-styrene triblock nanofibers produced at equivalent operating parameters. Based on the work completed, it is concluded that the styrene-isoprene-styrene triblock is not suitable for use in filtration with the current electrospinning conditions. On average, the styrene-isoprene-styrene triblock produced nanofibers of lower average diameter and lower standard deviation in diameter when compared to styene-butadiene-styrene triblock.

Nylon-6 Fabric Nanocomposite Resistance Temperature Detectors - Effects Of Oxidant, Mwcnt, And Nylon-6 Concentration, Rebecca Howdyshell

Williams Honors College, Honors Research Projects

Abstract

The purpose of this honors project is to construct and test temperature detectors, which can be used for the advancement of exercise devices, prosthetic sockets, or medical applications. Resistance Temperature Detectors (RTDs) are an effective way to measure temperature due to the dependence of the RTD material’s resistance on temperature. The focus of this project was to develop an RTD for prosthetic socket or exercise applications, where the RTD is in close contact with the skin of the user. Generally, RTDs are constructed from platinum, copper, or nickel. However, metal RTDs have a tendency to be large and rigid, …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Electrospinning Route For The Fabrication Of P-N Junction Using Nanofiber Yarns, A. F. Lotus, S. Bhargava, E. T. Bender, E. A. Evans, R. D. Ramsier, Darrell Hyson Reneker, G. G. Chase

College of Polymer Science and Polymer Engineering

Electrospinning is a simple, versatile, and cost effective method for generating nanoscale fibers, wires, and tubes. Nanowires and nanotubes could be important building blocks for nanoscale electronics, optoelectronics, and sensors as they can function as miniaturized devices as well as electrical interconnects. We report on a simple method to fabricate free standing ceramic nanofiber heterostructures, which exhibit rectifying behavior of a p-n junction.