Polymer Science Commons^™

Nanostructured Morphologies In Glassy Polymer Networks, Brian Greenhoe

Dissertations

The body of this work describes a novel approach for the dispersion of multi-walled carbon nanotubes in a high T_g epoxy prepolymer matrix using a twin screw high-shear continuous reactor. The method demonstrated improves on previous dispersion methods in several ways. It offers increased efficiency through excellent heat transfer, while being solvent-less, scale-able, and tailorable to drive dispersion states to judiciously chosen dispersion states. Furthermore, it was shown that dispersion state and agglomerate morphology can be directed, in several ways, through processing conditions and also by controlling the matrix viscosity profile through cure. Broadband dielectric spectroscopy, optical hot-stage microscopy, …

Design And Synthesis Of Dynamic Covalent Polymer Scaffolds With Controlled Architectures, Emily Annette Hoff

Dissertations

The design and synthesis of functional, controlled polymer architectures is essential to the development of new materials with precise and tailorable properties or applications. The work described in this dissertation focuses on the development of controlled polymer architectures with dynamic linkages for the design of multifunctional materials and surfaces via robust, efficient, and stimuli-responsive strategies.

In Chapter III, a post-polymerization modification strategy based on ambient temperature nucleophilic chemical deblocking of polymer scaffolds bearing N-heterocycle blocked isocyanate moieties is reported. Room temperature RAFT polymerization of three azole-N-carboxamide methacrylates, including 3,5-dimethyl pyrazole, imidazole, and 1,2,4-triazole derivatives, afforded reactive polymer scaffolds …

Plasma Processes And Polymers Third Special Issue On Plasma And Cancer, Mounir Laroussi, Annemie Bogaerts, Nazir Barekzi

Electrical & Computer Engineering Faculty Publications

(First paragraph) This issue of Plasma Processes and Polymers is the third in a series on the applications of low temperature plasma (LTP) against cancer, or “plasma oncology.” The papers in this issue are inspired from the talks given at the third International Workshop on Plasma for Cancer Treatment (IWPCT) which took place on April 11–12, 2016 in Washington, DC, USA. IWPCT is an international workshop that was created in 2014 as a venue to share cutting edge plasma oncology research. The first IWPCT was held in Washington DC, under the co-chairmanship of Prof. Mounir Laroussi (Old Dominion University) and …

Recent Approaches In Designing Bioadhesive Materials Inspired By Mussel Adhesive Protein, Pegah Kord Forooshani, Bruce P. Lee

Department of Biomedical Engineering Publications

Marine mussels secret protein-based adhesives, which enable them to anchor to various surfaces in a saline, intertidal zone. Mussel foot proteins (Mfps) contain a large abundance of a unique, catecholic amino acid, Dopa, in their protein sequences. Catechol offers robust and durable adhe-sion to various substrate surfaces and contributes to the curing of the adhesive plaques. In this article, we review the unique features and the key functionalities of Mfps, catechol chemistry, and strategies for preparing catechol-functionalized poly- mers. Specifically, we reviewed recent findings on the contributions of various features of Mfps on interfacial binding, which include coacervate formation, surface …

Effect Of Surface Treatment On Liquid Adhesion Inside 3-D Structures, Madani A. Khan, Jeffrey Alston, Andrew Guenthner, Jacob Zavala

STAR Program Research Presentations

This study explores the relationship between chemical surface treatments on the interior of glass tubes and their resistance to fluid flow. By treating the interior of the tubes with functional silanes we can decrease or increase the interaction of the tube walls with the fluid column, which translates to changes in fluid column height for a given pressure differential. Resistance to fluid flow is quantified by using the tubes as integral parts of a barometric pressure column and measuring the changes in column height as the fluid is pulled into the tube by a set pressure differential. The barometric pressure …

Film Performance Of Poly(Lactic Acid) Blends For Packaging Applications, Carlos A. Diaz, Hsunpao Y. Pao, Sungyoung Kim

Journal of Applied Packaging Research

Poly(lactic acid) (PLA), a biodegradable thermoplastic derived from renewable resources, stands out as a substitute to petroleum-based plastics. PLA based films for food packaging has been an area of both commercial and research interest within the context of sustainability. In spite of its high strength, packaging applications have been limited because PLA is more brittle than traditional oil-based plastics. Because of this, films display low tear and impact resistance and produce a loud crackling sound when manipulated. Although many studies address the toughening of PLA in the bulk, little attention has been placed on the film performance. The present study …

Occurrence Of Reverse Side Effects In Corona Treatment Of Dispersion-Coated Paperboard And Its Influence On Grease Barrier Properties, Sami-Seppo Ovaska, Ringaudas Rinkunas, Tadeusz Lozovksi, Robertas Maldzius, Jonas Sidaravicius, Leena-Sisko Johansson, Monika Österberg, Kaj Backfolk

Journal of Applied Packaging Research

The uncoated side of dispersion-barrier-coated paperboards was exposed to positive and negative direct current corona treatments in order to confirm the occurrence of backside treatment and clarify its effects on the usability of the paperboard. The main component of the coating dispersions was hydroxypropylated potato starch and the effects of talc and styrene-butadiene latex additions on backside treatment were evaluated. Coatings with a high talc proportion showed excellent initial grease resistance, but corona-induced strikethroughs caused a drastic decrease in grease penetration time. The root-mean-square roughness measurements revealed moderate surface roughening at the backside, indicating thus backside treatment. The alterations in …

Biodegradable Magnesium Alloys For Orthopaedic Applications: A Review On Corrosion, Biocompatibility And Surface Modifications., Sankalp Agarwal, James Curtin, Brendan Duffy, Swarna Jaiswal

Articles

Magnesium (Mg) and its alloys have been extensively explored as potential biodegradable implant materials for orthopaedic applications (e.g. Fracture fixation). However, the rapid corrosion of Mg based alloys in physiological conditions has delayed their introduction for therapeutic applications to date. The present review focuses on corrosion, biocompatibility and surface modifications of biodegradable Mg alloys for orthopaedic applications. Initially, the corrosion behaviour of Mg alloys and the effect of alloying elements on corrosion and biocompatibility is discussed. Furthermore, the influence of polymeric deposit coatings, namely sol-gel, synthetic aliphatic polyesters and natural polymers on corrosion and biological performance of Mg and its …

Microstructure And Rheology Of Carbon Nanotubes At Air-Water Interfaces, Charles D. Young

Honors Scholar Theses

This work characterizes the material properties of carbon nanotubes at air-water interfaces for potential use in creating stable emulsions. Properties such as length, aspect ratio, contact angle, microstructural ordering, surface pressure, compression and shear elastic moduli, stresses, surface viscosities and non-linearity are explored. Challenges such as deviation from a classical analysis of monolayers are encountered in the form of aggregation, mechanical contributions, and interface relaxation. These factors are taken into account to explain experimental measurements and trends. Ultimately, existing models for more homogeneous systems are resolved with observations to offer insight and areas of promise moving forward.

The Effect Of Assembly Technique On Weak Polyelectrolyte Multilayer Film Morphology And Humidity Swelling/Deswelling Behavior, Ziyang Yin

Graduate Theses - Chemical Engineering

The goal of this research is to investigate the film morphology and humidity swelling/deswelling behavior of polyelectrolyte multilayers (PEMs) that are constructed from poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) by two assembly techniques: automated dipping layer-by-layer (LbL) and spin-assisted (SA) LbL. Two sets of pH polyelectrolyte solution conditions were tested: (PAH7.5/PAA3.5) and (PAH7.0/PAA7.0). It was found that when the films were constructed with the same number of bilayers (=20 bilayers), SA-LbL (PAH7.5/PAA3.5) has a greater thickness than (PAH7.0/PAA7.0). (PAH7.5/PAA3.5) thin films constructed by automated dipping LbL did not result in a uniform film morphology, making thickness comparisons between techniques …

Development Of Pvdf Membrane Nanocomposites Via Various Functionalization Approaches For Environmental Applications, Douglas M. Davenport, Minghui Gui, Lindell E. Ormsbee, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

Membranes are finding wide applications in various fields spanning biological, water, and energy areas. Synthesis of membranes to provide tunable flux, metal sorption, and catalysis has been done through pore functionalization of microfiltration (MF) type membranes with responsive behavior. This methodology provides an opportunity to improve synthetic membrane performance via polymer fabrication and surface modification. By optimizing the polymer coagulation conditions in phase inversion fabrication, spongy polyvinylidene fluoride (PVDF) membranes with high porosity and large internal pore volume were created in lab and full scale. This robust membrane shows a promising mechanical strength as well as high capacity for loading …

Synthesis And Characterization Of Curcumin Polymer For Application In Radiation Induced Lung Damage, Mark C. Bailey

Theses and Dissertations--Chemical and Materials Engineering

Radiotherapy is used as a primary treatment for many cancers, including lung cancer. Although radiotherapy has proven to be an effective cancer treatment, its use is heavily limited due to the peripheral toxicity to healthy tissue. In this work, the antioxidant, curcumin, was tested as a radioprotectant to reduce radiation damage to healthy cells. Curcumin has been limited in use due to its poor bioavailability. In order to avoid problems associated with free curcumin delivery, curcumin poly(beta-amino ester) (CPBAE) was synthesized.

The first study investigated the in vitro radioprotection effect of curcumin in HUVEC dosed with gamma radiation. Cells treated …

Surface-Initiated Polymerizations For The Rapid Sorting Of Rare Cancer Cells, Jacob L. Lilly

Theses and Dissertations--Chemical and Materials Engineering

Cancer metastasis directly accounts for an estimated 90% of all cancer related deaths and is correlated with the presence of malignant cells in systemic circulation. This observed relationship has prompted efforts to develop a fluid biopsy, with the goal of detecting these rare cells in patient peripheral blood as surrogate markers for metastatic disease as a partial replacement or supplement to tissue biopsies. Numerous platforms have been designed, yet these have generally failed to support a reliable fluid biopsy due to poor performance parameters such as low throughput, low purity of enriched antigen positive cells, and insufficiently low detection thresholds …

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Construction Of Polyurethane Fabric Nanocomposites For Use In Resistance Temperature Detectors-Effect Of Polyurethane Concentration, Multi-Walled Carbon Nanotubes, And Oxidant, Jordan M. Shaffer

Williams Honors College, Honors Research Projects

Current resistance temperature detectors (RTDs) are rigid and create pressure points when used in contact with the human body. The current RTDs can also not be used in confined areas like the inside of a prosthetic. The research done for this paper explores the possibility of creating a soft fabric like RTD that can accurately measure temperature. This RTD could be used in medical devices, be placed in prosthetic legs, and be worn for a long period of time creating no discomfort for the user. Polyurethane scaffolds were created through an electrospinning process and multiwalled carbon nanotubes were adhered to …

Smart Fabrics For Colorimetric Detection, Breland Edwards

Undergraduate Research Posters

Due to the prevalence of chemical warfare, soldiers often carry chemical sensing devices, to warn of oncoming nerve agents. However, these devices are cumbersome. A lightweight, wearable chemical sensing fabric that doubles as a protectant against toxins would be beneficial. This fabric can be created by incorporating (1) organophosphate hydrolase, an enzyme capable of degrading organophosphates and releasing an acidic by product, and (2) polyaniline, a color changing polymer that changes from purple to green in the presence of acid, into nylon or polyvinyl alcohol nanofibers. The first step is to produce fabrics containing polyaniline and demonstrate that the fabrics …

Bioactive Poly(Beta-Amino Ester) Biomaterials For Treatment Of Infection And Oxidative Stress, Andrew L. Lakes

Theses and Dissertations--Chemical and Materials Engineering

Polymers have deep roots as drug delivery tools, and are widely used in clinical to private settings. Currently, however, numerous traditional therapies exist which may be improved through use of polymeric biomaterials. Through our work with infectious and oxidative stress disease prevention and treatment, we aimed to develop application driven, enhanced therapies utilizing new classes of polymers synthesized in-house. Applying biodegradable poly(β-amino ester) (PBAE) polymers, covalent-addition of bioactive substrates to these PBAEs avoided certain pitfalls of free-loaded and non-degradable drug delivery systems. Further, through variation of polymer ingredients and conditions, we were able to tune degradation rates, release profiles, cellular …

Synthesis And Characterization Of Antioxidant Conjugated Poly(Βeta-Amino Ester) Micro/Nanogels For The Suppression Of Oxidative Stress, Prachi Gupta

Theses and Dissertations--Chemical and Materials Engineering

Oxidative stress is a pathophysiological condition defined by an increased production of reactive oxygen species (ROS), which can result in the growth arrest of cells followed by cell disintegration or necrosis. A number of small molecule antioxidants (e.g. curcumin, quercetin and resveratrol) are capable of directly scavenging ROS, thereby short-circuiting the self-propagating oxidative stress state. However, poor solubility and rapid 1^st pass metabolism results in overall low bioavailability and acts as a barrier for its use as a drug to suppress oxidative stress efficiently.

To overcome this limitation, these small molecule antioxidants were covalently conjugated into poly(β-amino ester) (PβAE) …

Design And Development Of A High-Temperature High-Pressure Rolling Ball Viscometer/Densimeter And Evaluation Of Star Polymer-Solvent Mixtures, Matthew Stanton Newkirk

Theses and Dissertations

Modern automotive applications such as transmission clutch plates, combustion chambers, diesel fuel injector tips, and axle gears and friction plates operate at temperatures that can exceed 250°C and pressures of 40,000 psia. Industrial practice is to add homopolymers and copolymers to base oils to modify bulk fluid viscosity and frictional properties for these demanding applications. However, designing polymeric additives for lubricants and predicting their performance is limited by the lack of available high-temperature high-pressure (HTHP) viscosity and density data needed to test contemporary lubricity models. Thus, a major objective of this thesis is the design, development, and commissioning of a …