Electrospinning Aqueous Solutions Of Poly(Ethylene Oxide) Using A Corona-Type Apparatus, Nicholas Neill

Williams Honors College, Honors Research Projects

The purpose of this project was to evaluate working parameters for the corona spinneret to create electrospun fibers/ fiber mat. This project was set-up using a Box-Behnken design of experiment. The working parameters were investigated by performing the electrospinning process, altering the working conditions, collecting the electrospun fibers. The scope of this project includes three primary operational conditions: distance between the spinneret and the collection plate, the viscosity (weight percent) of PEO in the spinning solution and the weight percent of NaCl in the spinning solution. The distance between the spinneret and the collection plate were varied to 18 cm, …

Effects Of Hofmeister Ions On Gelation Of Gelatin And Pluronic Hydrogels, Eric Britton

Williams Honors College, Honors Research Projects

The purpose of the project was to observe the effects of the Hofmeister series of ions on the gelation of gelatin and Pluronic-127 hydrogels. Hydrogels are semi-solid materials that contain a network of joined molecules through intermolecular interactions which are capable of holding water. Gelatin and Pluronic-127 (PF-127) are thermoreversible, physical crosslinked gels. Gelation occurs when temperature, or other driving forces, reduce the polymer chain solubility until a distinct 2-phase system forms. When aqueous ions are present in solution, they exhibit specific ion effects that have either a stabilizing or destabilizing effect on the solubility of proteins and other polymers. …

Tandem Mass Spectrometry (Ms/Ms) For Determination Of Architecture Of Synthetic Polymers, Shoumik Saha

Williams Honors College, Honors Research Projects

Tandem Mass Spectrometry (MS/MS) was used to determine the architecture of synthetic polymers and they are difluorene-N₃, 3-difluorene-N₃ and VPOSS-3-difluorene. VPOSS materials usually exhibit electrochemical properties and the research was performed to determine their accurate structure and to provide evidence of their proper synthesis. The compounds were mixed with a matrix solution, DCTB, and a silver salt to enable proper protonation. The solvent mixture was on a MALDI plate and then put into the mass spectrometer. The mass spectrum generated was analyzed and each fragment was identified to structures with the synthetic polymers via ChemDraw. Thus, trial …

Correlation Of Electrospun Polyvinylpyrrolidone Fiber Mat Thickness With Basis Weight, Fiber Diameter, Pore Size Distribution, And Air Permeability, Leah Mcpherson

Williams Honors College, Honors Research Projects

This project developed correlations between electrospun polyvinylpyrrolidone fiber mat thickness, basis weight, fiber diameter, pore size, and air permeability. The hypotheses were thinner fibers produce thicker mats, pore size decreases with fiber diameter, pore size and permeability decrease as basis weight increases. Project results could be used for modeling or quality control purposes.

Fiber diameter distributions were analyzed using a Scanning Electron Microscope and FibraQuant 1.3 software. Four conditions were chosen for further study: 0.284 ± 0.104 µm, 0.379 ± 0.128 µm, 0.520 ± 0.138 µm, and 0.733 ± 0.177 µm. Lower PVP concentrations produced thinner fibers.

Sample thickness (nm) …

Modeling The Effect Thickener Structure Has On The Oil Release Of Grease, Dana Cressman

Williams Honors College, Honors Research Projects

Our hypothesis was that the thickener type and micelle concentration of grease affected its viscoelastic properties. Measurements were made using a TA AR G2 rheometer and calculations were made using TA rheometer analysis software to characterize the viscoelastic response of grease under oscillatory shear and frequency tests. The oscillatory frequency tests determined the critical micelle concentration. The oscillatory stress tests were taken at temperatures from 5 to 65 degrees Celsius to create a master curve based on time temperature superposition of the measurements. The crossover points of G’ and G” on the oscillatory stress tests demonstrated where the grease transitions …

Design Of Rubber Extraction Process From Tks Dandelion, Trevor A. Cody

Williams Honors College, Honors Research Projects

A design was developed for a controlled environment agriculture 3D greenhouse to grow and harvest TKS dandelions, as well as a processing plant to extract natural rubber and inulin from the roots. The design capacity was scaled for both pilot- and full-scale production: 100 and 100,000 tonnes of natural rubber per year, respectively. The byproducts of the process were dandelion greens, inulin, cellulose, and glucose; all of these except for cellulose were able to be valorized. The greenhouse was designed based on existing 3D hydroponic growing environments, and the extraction process was designed based on the original TKS dandelion extraction …

Design Of Natural Rubber Extraction From Tks Dandelion, Jehad S. Alrawajfeh, Trevor Cody, Jason Pogozelski

Williams Honors College, Honors Research Projects

A design was developed for a controlled environment agriculture 3D greenhouse to grow and harvest TKS dandelions, as well as a processing plant to extract natural rubber and inulin from the roots. The design capacity was scaled for both pilot- and full-scale production: 100 and 100,000 tonnes of natural rubber per year, respectively. The byproducts of the process were dandelion greens, inulin, cellulose, and glucose; all of these except for cellulose were able to be valorized. The greenhouse was designed based on existing 3D hydroponic growing environments, and the extraction process was designed based on the original TKS dandelion extraction …

Characterization Of Polyurethane For Use As Substrate In Nanofiber Sensor For Biomedical Applications, Megan Theaker

Williams Honors College, Honors Research Projects

The purpose of this project is to begin to determine properties of polymer nanocomposites that make a suitable substrate for nanofiber sensors. In this work, sensitivity of a sodium ion selective sensor constructed with polyurethane was used as a benchmark for comparison with sensors constructed with nylon-6. The sensors were characterized using contact angle and chronoamperometry. Using an ANOVA analysis, the results showed that the multi-walled carbon nanotube type was a significant factor on sensor response both with and without additional functionalization of the polymer by calixarene. The weight percentage of polyurethane in the electrospinning solution was also statistically significant …

Stability And Retention Enhancement Of Low Fouling Polystyrene Sulfonic Acid (Pss) And Polyethylene Glycol (Peg) Blend Films With Silane Coupling Agents, Sean Stybel

Williams Honors College, Honors Research Projects

The goal of this research project was to apply silane coupling agents for enhanced stability and retention of a low fouling polymeric coating to an inorganic substrate. A blend of polystyrene sulfonic acid (PSS) and polyethylene glycol (PEG) was crosslinked in order to create a low fouling film. The film was prepared by spin coating a PSS-PEG solution on an inorganic substrate coated with a layer of a silane coupling agent (3-aminopropyltriethoxysilane, APTES, solution), followed by thermal curing. The research was limited to less than one year and only used lab equipment available at the University of Akron. Stability and …

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Construction Of Polyurethane Fabric Nanocomposites For Use In Resistance Temperature Detectors-Effect Of Polyurethane Concentration, Multi-Walled Carbon Nanotubes, And Oxidant, Jordan M. Shaffer

Williams Honors College, Honors Research Projects

Current resistance temperature detectors (RTDs) are rigid and create pressure points when used in contact with the human body. The current RTDs can also not be used in confined areas like the inside of a prosthetic. The research done for this paper explores the possibility of creating a soft fabric like RTD that can accurately measure temperature. This RTD could be used in medical devices, be placed in prosthetic legs, and be worn for a long period of time creating no discomfort for the user. Polyurethane scaffolds were created through an electrospinning process and multiwalled carbon nanotubes were adhered to …

Electrospinning Of S-B-S Triblock And S-I-S Triblock Copolymers For Use In Fuel Filtration, Kevin Houser

Williams Honors College, Honors Research Projects

The following research project looked into the potential of using nanofibers of syrene-isoprene-styrene triblock copolymer produced through the electrospinning process for the filtration of water out of fuel as well as a comparison of styrene-isoprene-styrene triblock to the styrene-butadiene-styrene triblock nanofibers produced at equivalent operating parameters. Based on the work completed, it is concluded that the styrene-isoprene-styrene triblock is not suitable for use in filtration with the current electrospinning conditions. On average, the styrene-isoprene-styrene triblock produced nanofibers of lower average diameter and lower standard deviation in diameter when compared to styene-butadiene-styrene triblock.

Optimization Of Polydopamine Coatings, Helen C. Terrill Ms.

Williams Honors College, Honors Research Projects

Polydopamine coatings were fabricated onto the surfaces of glass slides, silicon wafers, and Teflon pieces. A method to change surface properties was optimized, providing a new way of using substrates by means of make-over surface properties. The technology has a wide range of potential approaches including high performance coatings and biomedical surfaces. The experiments can be conducted with various types of surface modifications to make surfaces hydrophilic, hydrophobic, conductive, or magnetic. The changes of film thickness and surface energy as functions of incubation time were quantified by means of ellipsometry, profilometry, and contact angle measurements. The use of primer polydopamine …

Nylon-6 Fabric Nanocomposite Resistance Temperature Detectors - Effects Of Oxidant, Mwcnt, And Nylon-6 Concentration, Rebecca Howdyshell

Williams Honors College, Honors Research Projects

Abstract

The purpose of this honors project is to construct and test temperature detectors, which can be used for the advancement of exercise devices, prosthetic sockets, or medical applications. Resistance Temperature Detectors (RTDs) are an effective way to measure temperature due to the dependence of the RTD material’s resistance on temperature. The focus of this project was to develop an RTD for prosthetic socket or exercise applications, where the RTD is in close contact with the skin of the user. Generally, RTDs are constructed from platinum, copper, or nickel. However, metal RTDs have a tendency to be large and rigid, …