Open Access. Powered by Scholars. Published by Universities.®

Polymer Science Commons™

Open Access. Powered by Scholars. Published by Universities.®

Other Chemical Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 31 - 40 of 40

Full-Text Articles in Polymer Science

The Effect Of Assembly Technique On Weak Polyelectrolyte Multilayer Film Morphology And Humidity Swelling/Deswelling Behavior, Ziyang Yin Feb 2016

The Effect Of Assembly Technique On Weak Polyelectrolyte Multilayer Film Morphology And Humidity Swelling/Deswelling Behavior, Ziyang Yin

Graduate Theses - Chemical Engineering

The goal of this research is to investigate the film morphology and humidity swelling/deswelling behavior of polyelectrolyte multilayers (PEMs) that are constructed from poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) by two assembly techniques: automated dipping layer-by-layer (LbL) and spin-assisted (SA) LbL. Two sets of pH polyelectrolyte solution conditions were tested: (PAH7.5/PAA3.5) and (PAH7.0/PAA7.0). It was found that when the films were constructed with the same number of bilayers (=20 bilayers), SA-LbL (PAH7.5/PAA3.5) has a greater thickness than (PAH7.0/PAA7.0). (PAH7.5/PAA3.5) thin films constructed by automated dipping LbL did not result in a uniform film morphology, making thickness comparisons between techniques …

Go to article

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel Jan 2016

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Go to article

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook Jun 2015

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Go to article

Inhalable Nanocomposites And Anticancer Agents For Cancer Therapy, Nathanael A. Stocke Jan 2015

Inhalable Nanocomposites And Anticancer Agents For Cancer Therapy, Nathanael A. Stocke

Theses and Dissertations--Chemical and Materials Engineering

Cancer is designated as the leading cause of mortality worldwide and lung cancer is responsible for nearly 30% of all cancer related deaths. Over the last few decades mortality rates have only marginally increased and rates of recurrence remain high. These factors, among others, suggest the need for more innovative treatment modalities in lung cancer therapy. Targeted pulmonary delivery is well established for treating pulmonary diseases such as asthma and provides a promising platform for lung cancer therapy. Increasing local deposition of anticancer agents (ACAs) and reducing systemic exposure of these toxic moieties could lead to better therapeutic outcomes and …

Go to article

Development Of Cementitious Materials For Adhesion Type Applications Comprising Calcium Sulfoaluminate (Csa) Cement And Latex Polymer, Joshua V. Brien Jan 2014

Development Of Cementitious Materials For Adhesion Type Applications Comprising Calcium Sulfoaluminate (Csa) Cement And Latex Polymer, Joshua V. Brien

Theses and Dissertations--Civil Engineering

The objective of this research was to develop high performing polymer modified calcium sulfoaluminate (CSA) cement materials for use in applications requiring superior adhesion characteristics. Little information is available describing interactions of CSA cement containing minor phase tri-calcium aluminate (C3A) with commonly used admixtures. Given the scarcity of information, a basic approach for developing cementitious materials was followed. The basic approach consisted of four tasks: cement design, admixture design, polymer design and testing developed materials. The iterative, time consuming process is necessary for understanding the influence of specific constituent components on overall system behavior. Results from the cement …

Go to article

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo Jan 2014

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Go to article

Generation Of Multicomponent Polymer Blend Microparticles Using Droplet Evaporation Technique And Modeling Evaporation Of Binary Droplet Containing Non-Volatile Solute, Venkat N. Rajagopalan Jan 2014

Generation Of Multicomponent Polymer Blend Microparticles Using Droplet Evaporation Technique And Modeling Evaporation Of Binary Droplet Containing Non-Volatile Solute, Venkat N. Rajagopalan

Theses and Dissertations--Chemical and Materials Engineering

Recently, considerable attention has been focused on the generation of nano- and micrometer scale multicomponent polymer particles with specifically tailored mechanical, electrical and optical properties. As only a few polymer-polymer pairs are miscible, the set of multicomponent polymer systems achievable by conventional methods, such as melt blending, is severely limited in property ranges. Therefore, researchers have been evaluating synthesis methods that can arbitrarily blend immiscible solvent pairs, thus expanding the range of properties that are practical. The generation of blended microparticles by evaporating a co-solvent from aerosol droplets containing two dissolved immiscible polymers in solution seems likely to exhibit a …

Go to article

Tobacco Mosaic Virus Implemented As An Interfacial Layer In Organic Photovoltaic Cells, Monica D. Del Real, Bryan Boudouris Oct 2013

Tobacco Mosaic Virus Implemented As An Interfacial Layer In Organic Photovoltaic Cells, Monica D. Del Real, Bryan Boudouris

The Summer Undergraduate Research Fellowship (SURF) Symposium

Organic photovoltaics (OPVs) are flexible, light weight, and economical to produce due to low processing temperatures, solution processing, and print fabrication. This makes them optimal for a wide range of applications. However, the efficiencies of OPVs are currently not high enough for them to be viable in the market or to be able to compete with inorganic photovoltaics. Therefore the integration of new materials and methods into OPVs in order to increase their efficiency is a vital field. One way to increase the efficiency of OPVs is to increase the surface area in-between layers to allow for enhanced electron transport. …

Go to article

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine Jan 2013

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine

Theses and Dissertations--Chemical and Materials Engineering

Ultrathin film nanocomposites are becoming increasingly important for specialized performance of commercial coatings. Critical challenges for ultrathin film nanocomposites include their synthesis and characterization as well as their performance properties, including surface roughness, optical properties (haze, refractive index as examples), and mechanical properties. The objective of this work is to control the surface roughness of ultrathin film nanocomposites by changing the average particle size and the particle volume fraction (loading) of monomodal particle size distributions. This work evaluated one-layer and two-layer films for their surface properties. Monodispersed colloidal silica nanoparticles were incorporated into an acrylate-based monomer system as the model …

Go to article

Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi Feb 2008

Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Within the framework of study of concrete structures subjected to fire, .a theoretical and experimental work was conducted. The aim of this study was to investigate and to model the damage mechanisms of concrete after their exposure to high temperatures. The multiphase Digital Concrete Model as well as the damage model, MOD EV, which were both implemented on the finiteelem~ rit software package, SYMPHONIE, were used simμltaneously to assess the thermal damage of the concrete. In order to validate the thermal damage model, an experimental investigation was performed. The mechanical characteristics of 5 cementitious materials, which included cement paste, mortar, …

Go to article

First Prev