Polymer Science Commons^™

Plastic Crystal - Gel Polymer Electrolytes For Magnesium Rechargeable Batteries, Diyana Hambali

Student Works (2020-2029)

Polymer electrolytes are known to be the possible substitution for liquid electrolytes due to their excellent safe performance and good compatibility with electrodes compared to its liquid counterpart. Thus, in the present work, gel polymer electrolytes (GPEs) have been studied comprising plastic crystal succinonitrile (SN) to form plastic crystal - gel polymer electrolytes. The GPEs were prepared by using two types of magnesium salts which are magnesium trifluoromethanesulfonate (MgTf2) and magnesium bis(trifluoromethanesulfonimide) (Mg(TFSI)2) varied from 5 to 30 wt.%. In the preparation of GPEs, four GPE systems were introduced which are single plasticized systems (PVdC-co-AN/SN/MgTf2 and PVdC-co-AN/SN/Mg(TFSI)2) and double plasticized …

Preparation And Characterisation Of Heat Treated Oil Palm-Empty Fruit Bunch/High Density Polyethylene Composites, Nordin Nur Afifah

Student Works (2020-2029)

Natural fibre composites (NFCs) are composite materials, in which the reinforcing fibres are derived from renewable and carbon dioxide neutral resources such as wood or plants. NFC can be made by replacing synthetic fibres with various types of natural fibres. Oil palm empty fruit bunch (OPEFB) fibre and oil palm mesocarp fibre are two important types of fibrous materials left in the palm-oil industry. In this study, EFB will be used as a reinforcement to the high-density polyethylene (HDPE). EFB was heat-treated at 180°C using vacuum oven for one hour, extrusion compounded with HDPE at 10%, 20% and 30% weight …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Development Of Forward Osmosis Based Separations: A Novel Approach In Membrane Technology, Yu-Hsuan Chiao

Graduate Theses and Dissertations

Tackling the worldwide severe water shortage, the membrane technology is considered to be the most efficient approach and hence, used widely as a cost-effective sustainable solution. “Forward osmosis (FO)” has been the major attention in recent time. FO uses osmotic pressure as the driving force to draw the water passing the membrane and achieve the desired separation performance. In general, it is considered to be a process with tremendous potential to resolve the present-day water shortage with extremely low energy consumption. However, the challenges of membrane and draw solution regeneration associated with FO processes must be conquered prior to their …

Decorative Articles Based On Polymeric Materials, Yaser M. Asal Mr., M. A. Radwan, Hany A. Elazab Dr, Bassant Hussein, Mohamed A. Sadek

Chemical Engineering

The aim of the research is to create decorative articles based on polymeric materials, study the effects of fillers and the type of moulds that it can cope with the exothermic reaction nature of resin to create a scientific background on the usage of the resins in daily life products. The polymeric materials that will be concentrated on are the unsaturated polyester resins and epoxy resins. The unsaturated polyester is of many types and chemical constituents, the used experimentally is a general-purpose type and the epoxy also have different types and the used is a commercially 3D floor coating type. …

Non-Einstein Viscosity Phenomenon Of Acrylonitrile–Butadiene–Styrene Composites Containing Lignin–Polycaprolactone Particulates Highly Dispersed By High-Shear Stress, Sing-Hoon Kim, Kisuk Choi, Kyouk Ryeol Choi, Taesung Kim, Jonghwan Suhr, Kwang Jin Kim, Hyoung Jin Choi, Jae-Do Nam

Mechanical Engineering Faculty Research

Lignin powder was modified via ring-opening polymerization of caprolactone to form a lignin–polycaprolactone (LPCL) particulate. The LPCL particulates were mixed with an acrylonitrile–butadiene–styrene (ABS) matrix at an extremely high rotational speed of up to 3000 rpm, which was achieved by a closed-loop screw mixer and in-line melt extruder. Using this high-shear extruding mixer, the LPCL particulate size was controlled in the range of 3395 nm (conventional twin-screw extrusion) down to 638 nm (high-shear mixer of 3000 rpm) by altering the mixing speed and time. The resulting LPCL/ABS composites clearly showed non-Einstein viscosity phenomena, exhibiting reduced viscosity (2130 Pa·s) compared to …

“Polysoaps” Via Raft Copolymerization To Form Well-Defined Micelles For Water Remediation And Targeted Drug Delivery Applications, Phillip Pickett

Dissertations

Amphiphilic copolymers have become increasingly important for environmental and biological applications due to their behavioral characteristics in aqueous solution. For example, structurally-tailored statistical amphiphilic copolymers or “polysoaps” can self-assemble into micelles or other architectures in water at various concentrations. Polysoaps may be differentiated from small molecule surfactant micelles in their capability to self-assemble into unimolecular associates (unimolecular micelles) with no dependence on concentration. Such micelles offer enormous potential for dispersion of hydrophobic species in water at high dilution. Importantly, each polymer chain forms its own micelle and upon dilution, these micelles remain intact and capable of dispersing hydrocarbon material in …

Using Green Emitting Ph-Responsive Nanogels To Report Environmental Changes Within Hydrogels: A Nanoprobe For Versatile Sensing, Mingning Zhu, Dongdong Lu, Shanglin Wu, Qing Lian, Wenkai Wang, L. Andrew Lyon, Weiguang Wang, Paulo Bártolo, Brian R. Saunders

Engineering Faculty Articles and Research

Remotely reporting the local environment within hydrogels using inexpensive laboratory techniques has excellent potential to improve our understanding of the nanometer-scale changes that cause macroscopic swelling or deswelling. Whilst photoluminescence (PL) spectroscopy is a popular method for such studies this approach commonly requires bespoke and time-consuming synthesis to attach fluorophores which may leave toxic residues. A promising and more versatile alternative is to use a pre-formed nanogel probe that contains a donor/acceptor pair and then “dope” that into the gel during gel assembly. Here, we introduce green-emitting methacrylic acid-based nanogel probe particles and use them to report the local environment …

Nanogels And Microgels: From Model Colloids To Applications, Recent Developments, And Future Trends, Mattias Karg, Andrij Pich, Thomas Hellweg, Todd Hoare, L. Andrew Lyon, J. J. Crassous, Daisuke Suzuki, Rustam A. Gumerov, Stefanie Schneider, Igor I. Potemkin, Walter Richtering

Engineering Faculty Articles and Research

Nanogels and microgels are soft, deformable, and penetrable objects with an internal gel-like structure that is swollen by the dispersing solvent. Their softness and the potential to respond to external stimuli like temperature, pressure, pH, ionic strength, and different analytes make them interesting as soft model systems in fundamental research as well as for a broad range of applications, in particular in the field of biological applications. Recent tremendous developments in their synthesis open access to systems with complex architectures and compositions allowing for tailoring microgels with specific properties. At the same time state-of-the-art theoretical and simulation approaches offer deeper …

Multidimensional Mass Spectrometry Of Chemonic™ Ccg-6 Nonionic Surfactant With Separation By Polarity And Shape, Charles Johnson

Williams Honors College, Honors Research Projects

Chemonic™ CCG-6 surfactant is a water-soluble poly(ethylene glycol) (PEG) conjugated alkyl glyceride emollient. This surfactant exists as a complex mixture of a glycerol cores conjugated with poly(ethylene glycol) branches (PEGylation) that were partially esterified with caprylic (C8) and capric (C10) acids. These may be esterified on one, two, or all three arms of the glyceride. The architecture of the structures in this mixture was studied using multidimensional mass spectrometry (MS). Mass spectrometry was interfaced with ultra-performance liquid chromatography (UPLC) and ion mobility (IM) separation. The mixture was separated by reversed-phase LC, oligomers of the star-branched polymer were separated according to …

High-Throughput Assessment Of A Novel, Thiol-Acrylate Hydrogel For Tumor Spheroid Synthesis In A Microfluidic Device, Nathan Daniel Kersker

LSU Master's Theses

The extracellular environment plays an important role in regulating cell behavior. The mechanical, structural, and compositional properties of the extracellular matrix can determine the fate of the growing cells. Standard two-dimensional culturing in a flask fails to represent a native cellular environment. To create the native environment suitable for cells, hydrogels were previously studied. One of the most extensively studied synthetic hydrogels was a poly(ethylene glycol diacrylate) (PEGDA) hydrogel. However, the need for UV polymerization may introduce unwanted changes in cell morphology and viability. The hydrogel being proposed was a form of a thiol-acrylate hydrogel that can eliminate this problem …

An Entirely New Molecular Glue For Mof Using Unusual Structural Transformation Of A Coordination Polymer, Sukwoo Jung, Hangyeol Kim, Junseok Ahn

The International Student Science Fair 2018

In this research, an entirely new molecular glue is reported. This ‘coordination polymer glue’ is synthesized from zinc metal and BDC-NPE(2,5-bis{4-[1-(4-nitrophenyl)ethylamino]butoxy}terephthalic acid). Molecular glue transforms from 1D coordination polymer to a 3D cross-linked framework, resulting in a phase change of solution to solid. The carboxylate group of this glue makes the preformed MOF bind to its framework. Therefore, when the solution of molecular glue is mixed with preformed MOF powder and heated, homogeneous and thin MOF film – MOF/ZnNPE film – is fabricated. The film is irrelevant to the kind of its substrate, and its thermal stability was enhanced in …

An Entirely New Molecular Glue For Mof Using Unusual Structural Transformation Of A Coordination Polymer, Sukwoo Jung, Hangyeol Kim, Junseok Ahn

The International Student Science Fair 2018

In this research, an entirely new molecular glue is reported. This ‘coordination polymer glue’ is synthesized from zinc metal and BDC-NPE(2,5-bis{4-[1-(4-nitrophenyl)ethylamino]butoxy}terephthalic acid). Molecular glue transforms from 1D coordination polymer to a 3D cross-linked framework, resulting in a phase change of solution to solid. The carboxylate group of this glue makes the preformed MOF bind to its framework. Therefore, when the solution of molecular glue is mixed with preformed MOF powder and heated, homogeneous and thin MOF film – MOF/ZnNPE film – is fabricated. The film is irrelevant to the kind of its substrate, and its thermal stability was enhanced in …

Biocompatible, Responsive Polysoaps Via Raft Copolymerization For The Delivery Of Model Cancer Therapeutics, Mason Dearborn

Honors Theses

Many chemotherapeutic drugs are small, hydrophobic molecules that require water-soluble, biocompatible nanocarriers for enhanced vascular circulation. Existing polymeric carriers either conjugate the drug along a copolymer backbone or sequester drugs within a protected interior domain to be delivered to specific sites in the body. Such therapeutic systems must overcome a myriad of hurdles, beginning with complex, multi-step syntheses, followed by other inherent barriers that limit the efficiency of drug delivery at the targeted site. This work aims to circumvent a number of these issues using biocompatible, stimuli-responsive polysoaps that are capable of unimeric micelle formation, hydrophobic drug delivery, and triggered …

Polymer Nanocomposites Containing High Aspect Ratio Particulates: Innovation In Co-Extruded Multilayer Barrier Films, Kevin Meyers

Dissertations

Delaminated montmorillonite (MMT) clay/ maleic anhydride grafted LLDPE nanocomposite multilayer films with alternating layers of LDPE were produced through multilayer co-extrusion. The MMT concentration within the nanocomposite layers was increased through annealing the films in the melt due to a mismatch in interdiffusion rates of the polymer layers. Analysis of the nanocomposite layers upon annealing revealed that the platelets impinged upon one another resulting in significant improvement in oxygen barrier in the multilayer system, exceeding the results of bulk nanocomposites.

Model analysis demonstrated that increasing the nanoplatelet aspect ratio or initial concentration in the filled layers would lead to even …

Highly Flame Retardant And Bio-Based Rigid Polyurethane Foams Derived From Orange Peel Oil, Chunyang Zhang

Electronic Theses & Dissertations

Polyurethane is an important class of polymer which is being used for various industrial applications in the form of rigid foams, flexible foams, thermoplastic, elastomer, coating, and adhesive. Especially there is a huge market for rigid polyurethane foams for their applications as thermal insulating material in building and housing. In general, polyurethanes are prepared using polyols and diisocyanates. Most of the polyols used by industries are petrochemical based. In this project, a novel polyol from an orange peel oil-based derivative, limonene dimercaptan, was synthesized using one step photochemical thiol-ene reaction. The synthesized polyol was used to prepare flame retardant polyurethane …

Tandem Mass Spectrometry (Ms/Ms) For Determination Of Architecture Of Synthetic Polymers, Shoumik Saha

Williams Honors College, Honors Research Projects

Tandem Mass Spectrometry (MS/MS) was used to determine the architecture of synthetic polymers and they are difluorene-N₃, 3-difluorene-N₃ and VPOSS-3-difluorene. VPOSS materials usually exhibit electrochemical properties and the research was performed to determine their accurate structure and to provide evidence of their proper synthesis. The compounds were mixed with a matrix solution, DCTB, and a silver salt to enable proper protonation. The solvent mixture was on a MALDI plate and then put into the mass spectrometer. The mass spectrum generated was analyzed and each fragment was identified to structures with the synthetic polymers via ChemDraw. Thus, trial …

Responsive Nanogel Probe For Ratiometric Fluorescent Sensing Of Ph And Strain In Hydrogels, Mingning Zhu, Dongdong Lu, Shanglin Wu, Qing Lian, Wenkai Wang, Amir H. Milani, Zhengxing Cui, Nam T. Nguyen, Mu Chen, L. Andrew Lyon, Daman J. Adlam, Anthony J. Freemont, Judith A. Hoyland, Brian R. Saunders

Engineering Faculty Articles and Research

In this study a new pH-responsive nanogel probe containing a complementary nonradiative resonance energy transfer (NRET) fluorophore pair is investigated and its ability to act as a versatile probe of network-related changes in three hydrogels demonstrated. Fluorescent sensing using NRET is a powerful method for studying relationships between Angstrom length-scale structure and macroscopic properties of soft matter. Unfortunately, inclusion of NRET fluorophores into such materials requires material-specific chemistry. Here, low concentrations of preformed nanogel probes were included into hydrogel hosts. Ratiometric photoluminescence (PL) data for the gels labeled with the nanogel probes enabled pH-triggered swelling and deswelling to be studied …

Cellulose Reinforced Thermoplastic Composites By In-Situ Ring-Opening Polymerization, Shahab Kashani Rahimi

Dissertations

Over the past two decades, the increasing concern about the negative environmental impacts of synthetic materials has led to rising interests in utilizing renewable natural resources to develop polymer materials with comparable properties and performance to their synthetic counterparts. One of the major fields of interest is polymer composites where the replacement of synthetic fibers with bio renewable natural fibers is of great potential. However, the processing difficulties, in terms of fiber dispersion and thermal stability have limited the application of cellulosic fibers to polymers with low processing temperatures which are mostly hydrophobic polymers. As a result, the true reinforcing …

A Comparison Study Of Two Synthesis Methods For Polymer Of Intrinsic Microporosity 1 (Pim-1), Conor S. Perry

Materials Engineering

Polymers of Intrinsic Microporosity (PIMs) are an emerging polymeric material class for molecular sieving applications. This study focuses on PIM-1, an alternating copolymer of 5,5’,6,6’-tetrahydroxy-3,3’,3,3’-tetramethyl-1,1’-spirobisindane and tetrafluoroterephthalonitrile synthesized via nucleophilic aromatic substitution. PIM-1 been widely studied as a gas separating material and filtering membrane, but in this case, it is studied as a battery separator material. PIM-1’s microporous (pore diameters less than 2 nm) structure allows smaller favorable ions to transport while preventing larger ions and compounds from transporting. Two synthesis methods, round bottom flask synthesis and ball mill synthesis, of PIM-1 are compared to see any improved characteristics. The …

Synthesis And Characterization Of Molybdenum Sulfide And For Hydrogen Evolution Reaction And Supercapacitor Applications, Zhuo Wang

Electronic Theses & Dissertations

To meet the constantly rising requirement of energy other than traditional fossil fuel and environment protection, it is a perfect time to development low cost, and efficient materials for clean energy production. Hydrogen generation by water splitting is one of the cleanest ways to produce cheaper energy. Hydrogen evolution reaction (HER) is one of the key steps in water splitting process. Ideally, the thermodynamic potential for HER should be at 0 V (vs. SHE). However, without an efficient catalyst, this reaction occurred at higher potential, called overpotential. A good HER catalyst is needed to lower the overpotential and hence to …

Polyisobutylene Telechelic Prepolymers By In Situ End-Quenching And Post-Polymerization Modifications, Bin Yang

Dissertations

This volume focuses on the development of telechelic polyisobutylene (PIB) prepolymers by combining end-capping of living carbocationic polymerization of isobutylene (IB) with suitable reactants and post-polymerization modifications. Alkylation kinetics of PIB tert-chloride with alkoxybenzenes using either TiCl₄ or AlCl₃ were investigated. Quantitative para-position end-capped products were only achieved if the alkoxybenzene/AlCl₃ molar ratio was greater than unity; while no such molar ratio is required for TiCl₄, but the alkylation rate was slower than AlCl₃ under the same conditions. Photopolymerization kinetics analysis of PIB triphenol tri(meth)acrylates with low and high M_ns, …

A Quartz Crystal Microbalance Study Of Thiol:Ene Poly(Ionic Liquid) Polymerization And Gas Absorption, Yueming Wu

Murray State Theses and Dissertations

ABSTRACT

The polymerization process of, and gas absorption by, imidazolium-containing thiol:ene poly (ionic liquid)s (PILs), prepared from bisallylimidazolium bis(trifluoromethyl sulfonyl)imide [NTf₂^-] and pentaerythritoltetrakis(3 mercaptopropionate), was studied. The thiol:ene PILs examined were recently reported by groups at Murray State University. The advantage of thiol:ene PILs over other reported PILs is that thiol:ene polymers are made rapidly by UV exposure and exhibit high mechanical and thermal stability due to high cross-linking. The properties of interest for the thiol:ene PILs were studied using a quartz crystal microbalance (QCM). QCM techniques are based on the piezoelectric effect, where certain crystals (e.g., …

Design And Synthesis Of Dynamic Covalent Polymer Scaffolds With Controlled Architectures, Emily Annette Hoff

Dissertations

The design and synthesis of functional, controlled polymer architectures is essential to the development of new materials with precise and tailorable properties or applications. The work described in this dissertation focuses on the development of controlled polymer architectures with dynamic linkages for the design of multifunctional materials and surfaces via robust, efficient, and stimuli-responsive strategies.

In Chapter III, a post-polymerization modification strategy based on ambient temperature nucleophilic chemical deblocking of polymer scaffolds bearing N-heterocycle blocked isocyanate moieties is reported. Room temperature RAFT polymerization of three azole-N-carboxamide methacrylates, including 3,5-dimethyl pyrazole, imidazole, and 1,2,4-triazole derivatives, afforded reactive polymer scaffolds …

Recent Approaches In Designing Bioadhesive Materials Inspired By Mussel Adhesive Protein, Pegah Kord Forooshani, Bruce P. Lee

Department of Biomedical Engineering Publications

Marine mussels secret protein-based adhesives, which enable them to anchor to various surfaces in a saline, intertidal zone. Mussel foot proteins (Mfps) contain a large abundance of a unique, catecholic amino acid, Dopa, in their protein sequences. Catechol offers robust and durable adhe-sion to various substrate surfaces and contributes to the curing of the adhesive plaques. In this article, we review the unique features and the key functionalities of Mfps, catechol chemistry, and strategies for preparing catechol-functionalized poly- mers. Specifically, we reviewed recent findings on the contributions of various features of Mfps on interfacial binding, which include coacervate formation, surface …

Effect Of Surface Treatment On Liquid Adhesion Inside 3-D Structures, Madani A. Khan, Jeffrey Alston, Andrew Guenthner, Jacob Zavala

STAR Program Research Presentations

This study explores the relationship between chemical surface treatments on the interior of glass tubes and their resistance to fluid flow. By treating the interior of the tubes with functional silanes we can decrease or increase the interaction of the tube walls with the fluid column, which translates to changes in fluid column height for a given pressure differential. Resistance to fluid flow is quantified by using the tubes as integral parts of a barometric pressure column and measuring the changes in column height as the fluid is pulled into the tube by a set pressure differential. The barometric pressure …

Hybrid Aryl-Ether-Ketone And Hyperbranched Epoxy Networks, John Misasi

Dissertations

In this dissertation, relationships between chemical structures, cure kinetics and network architectures are correlated to bulk mechanical properties for novel, hybrid epoxy-amine networks. The work is split into two primary sections: the first is the synthesis and characterization of multifunctional glassy networks based on aryl-ether-ketone diamine curatives, while the second is based on the synthesis and characterization of hyperbranched epoxy polymers and their resulting networks.

Three aryl-ether-ketone (AEK) diamines of increasing molecular weights were synthesized and used to cure 4,4’-tetraglycidylether of diaminodiphenylmethane (TGDDM); the resulting networks were compared to 4,4’-diaminodiphenyl sulfone cured TGDDM. Architectural differences were created by varying cure …

Synthesis, Characterization, And Thermoelectric Properties Of Radical Siloxanes, Arnold J. Eng, Bryan Boudouris, Edward P. Tomlinson, Martha Emily Hay

The Summer Undergraduate Research Fellowship (SURF) Symposium

More than half of the annual energy consumption in the United States is lost as waste heat. Polymer-based thermoelectric devices have the potential to utilize this waste heat both sustainably and cost-effectively. Although conjugated polymers currently dominate research in organic thermoelectrics, the potential of using polymers with radical pendant groups have yet to be realized. These polymers have been found to be as conductive as pristine (i.e., not doped) poly(3-hexylthiophene) (P3HT), a commonly-used charge-transporting conjugated polymer. This could yield promising avenues for thermoelectric material design as radical polymers are more synthetically tunable and are hypothesized to have a high Seebeck …