Petroleum Engineering Commons^™

Mechanism Of Improved Miscibility Of Co2–Oil Systems By Multiester-Headgroup Surfactants, Ning Xu, Yanling Wang, Baojun Bai, Yu Zhang, Wenjing Shi, Zhaonian Zhang, Wenhui Ding, Peixu Ma, Zan Gao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

In the pursuit of carbon neutrality, the CO₂-enhanced oil recovery provides dual benefits by enabling both carbon sequestration and incremental oil production. However, its application is limited by high minimum miscibility pressure. CO₂-philic and oil-affinitive surfactants have emerged as an effective, low-dosage, and cost-efficient strategy to reduce the minimum miscibility pressure. In this study, macroscopic phase behavior experiments combined with molecular dynamics simulations were employed to systematically elucidate the influence of multiester-head surfactants on CO₂–oil miscibility. Using a modified pressure–volume–temperature apparatus equipped with optical power monitoring, we determined that multiester-head surfactants reduced the first-contact …

Controlled Gelation Of Co₂-Resistant Polymer Systems For Improved Conformance In Co₂-Eor, Maryam Sharifi Paroushi

Miners Solving for Tomorrow Research Conference

This presentation introduces a CO₂-resistant hydrogel developed to control fluid movement and improve CO₂ injection performance in subsurface reservoirs for Enhanced Oil Recovery (EOR) and Carbon Capture and Storage (CCS). Conventional polymer gels often lose strength in CO₂-rich environments, resulting in weak plugging, early breakdown, and ineffective flow control. To address this limitation, a sulfonated HPAM-based gel system crosslinked with chromium was developed. The effects of polymer concentration, molecular weight, crosslinker ratio, ionic strength, and pH were investigated to better understand gelation behavior and performance. The formulation exhibited controlled gelation, strong resistance to temperature and CO₂, and minimal shrinkage over …

Assessing The Geomechanical Modelling Of Underground Reservoir For Co₂ Storage Trapping Mechanisms, Bonavian Hasiholan, Mohammed Ali Farea, Elhassan Mostafa Abdallah, Sami Abdelrahman M. Yagoub, Yasir Mukhtar

Mathematical Modelling and Numerical Simulation with Applications

Effective carbon dioxide (CO₂) storage is essential for mitigating climate change amid increasing global greenhouse gas emissions. This study investigates the influence of geomechanics on CO₂ storage performance within carbon capture and storage (CCS), focusing on structural, residual, and solubility trapping mechanisms using a fully coupled modeling framework. Two numerical models, with and without geomechanical effects, are developed to evaluate impacts on reservoir behavior, CO₂ migration, and trapping efficiency. Each mechanism is analyzed separately and within an integrated framework to assess their combined contributions. Results indicate that geomechanical coupling increases reservoir pressure, reduces CO₂ flow velocity, enhances migration control, and …

Effect Of Ionic Strength On Gelation Time And Strength Of Amps-Based Polymer Gels, Maryam Sharifi Paroushi, Xuyang Tian, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Polymer gel treatment has been widely applied for improving sweep efficiency and controlling excessive water and gas production. Their performance depends on gelation time and final gel strength. In most studies, brine salinity is used to describe the effect of formation water on gel behavior. However, changing salinity also changes ionic strength and ion composition at the same time. Because of this coupling, it is difficult to identify the mechanisms controlling gelation, which has led to inconsistent trends in the literature. Increasing salinity has been reported to either slow or accelerate gelation and to weaken or strengthen gels depending on …

Evaluation Of A Novel Re-Crosslinkable Preformed Particle Gel For Conformance Control In Ultra-High Temperature Reservoirs, Yanbo Liu, Tao Song, Caleb Kwasi Darko, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

Preferential fluid flow remains a major challenge in subsurface energy production and gas storage operations, resulting in excessive water production in mature oil fields, reduced heat extraction in geothermal reservoirs, and low sweep and storage efficiency in CO₂-EOR projects. Polymer gels are widely used to mitigate high-permeability channels; however, conventional systems exhibit limited plugging efficiency and short lifetimes in ultra-high-temperature reservoirs due to poor thermal stability. This study presents a novel ultra-high-temperature-resistant preformed particle gel (UHT-PPG) developed for conformance control in reservoirs with temperatures of 150–275 °C and severe super-K or channeling problems. The material was evaluated in …

Evaluation Of Chromium-Crosslinked Amps-Hpam Copolymer Gels: Effects Of Key Parameters On Gelation Time And Strength, Maryam Sharifi Paroushi, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Controlling CO₂ channeling in heterogeneous reservoirs remains a major challenge for both enhanced oil recovery (EOR) and secure geological storage. AMPS-HPAM copolymers exhibit high-temperature resistance and brine tolerance compared with conventional HPAM gels, making them well suited for the harsh environments associated with CO₂ injection. Chromium-based crosslinkers (CrAc and CrCl₃) were investigated because sulfonic acid groups in AMPS can coordinate with trivalent chromium ions, enabling dual ionic crosslinking and the formation of a robust gel network. While organic crosslinked AMPS-HPAM gels have been widely studied, the behavior of chromium-crosslinked AMPS-containing systems, particularly their gelation kinetics under …

Solubility And Dissolution Mechanism Of Novel Multi-Ester Headgroup Surfactants In Supercritical Co2, Ning Xu, Yan Ling Wang, Baojun Bai, Shi Zhang Cui, Yu Zhang, Wen Jing Shi, Zhao Nian Zhang, Wen Hui Ding, Pei Xu Ma, Zan Gao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

To address the limited solubility and applicability of conventional hydrocarbon surfactants in supercritical CO₂, a series of multi-ester headgroup surfactants were designed and synthesized by leveraging the CO₂-philic properties of ester groups. The molecular structures were characterized using Fourier transform infrared (FT-IR) spectroscopy and ¹H NMR. A custom-designed laser-based apparatus was developed to quantify surfactant solubility and systematically investigate phase behavior in CO2. Molecular dynamics (MD) simulations were employed to elucidate structure–solubility relationships across multiple scales, including solubility parameters, interaction energies, radial distribution functions (RDFs), and free volume fractions. Results indicate that, at 323.15 K, …

Deep Learning-Based Co-Current Upward Gas-Liquid Two-Phase Flow Regime Identification In An Annular Conduit, Joshua Robert Macomber

Graduate Theses, Dissertations, and Problem Reports (ETD)

Flow regime identification in co-current upward gas-liquid flow through annular conduits remains a significant challenge in petroleum engineering, with major safety and operational implications. It is also important across industries involving the transport of multiphase fluids. Misidentifying flow regimes can introduce major operational risk, yet regime boundaries in annular gas-liquid flow are often visually complex and context dependent.

The objective of this study was to evaluate the utility of convolutional neural network (CNN) classifiers for flow regime identification. The CNN was trained using annular flow image dataset published by Texas A&M University. The dataset consists of approximately 947 RGB images …

Utilizing Coal For Mesophase Pitch-Based Carbon Fiber Production: Precursors, Processes, And Progress, Christina M. Thompson

Theses and Dissertations--Chemistry

Graphitic materials possess unique properties due to the unique combination of layered crystalline structure and carbon’s low atomic weight. High performance carbon fiber is one such example, displaying exceptional strength-to-weight ratios, stiffness, and thermal and chemical resistance. These properties render high performance carbon fiber a critical structural reinforcement material in the manufacture of composites across various industries, such as for automotive and aerospace applications. However, balancing fiber performance with precursor and processing costs remains a challenge. As alternative carbonaceous feedstocks are explored, coal has gained interest for utilization in graphitic products as a relatively abundant and low-cost source of aromatic …

Predicting Simulation Times For Multiphase Thermal-Hydraulic Models, Andrew Yule, Andrew Taylor

SMU Data Science Review

Addressing the challenge of computationally intensive OLGA

simulations in the oil and gas industry, a machine learning framework is

developed for accurate runtime prediction. A specialized feature extraction

pipeline identifies key parameters—such as simulation time, time step,

number of branches, and section count—from OLGA input files that serve as

high-impact predictors. Multiple predictive models, including regression,

tree-based ensembles, and neural networks, are implemented to validate

accuracy and robustness. Results reveal that prioritizing simulations based on

predicted runtimes optimizes licensing resources and reduces operational

costs, making real-time scheduling more efficient. This research demonstrates

the effectiveness of data-driven runtime prediction in enhancing …

Laboratory Investigation Of High-Temperature Preformed Particle Gels For Fluid Control In Granite Cores For Geothermal Applications, K. Caleb Darko, Yanbo Liu, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

To understand the applicability of high-temperature preformed particle gel (HT-PPG) for control of short-circuiting in enhanced geothermal systems (EGSs), core flooding experiments were conducted on fractured granite cores under varying fracture widths, gel particle sizes and swelling ratios. Key parameters such as injection pressure, water breakthrough pressure, and residual resistance factor were measured to evaluate HT-PPG performance. The gel exhibited strong injectability, entering granite fractures at pressure gradients as low as 0.656 MPa/m; HT-PPG yields a superior sealing performance by significantly reducing the permeability; and dehydration occurs during HT-PPG propagation, with a dehydration ratio ranging from 4.71% to 11.36%. This …

Effect Of Clays On The Spontaneous Imbibition Behavior Of Surfactant Solutions In Shale Oil Reservoirs, Ning Xu, Yanling Wang, Baojun Bai, Chuanbao Zhang, Shizhang Cui, Yu Zhang, Di Li, Wenjing Shi, Wenhui Ding

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Surfactant-enhanced spontaneous imbibition is a proven method of enhancing oil recovery from shale reservoirs. However, a significant knowledge gap concerning the impact of clay minerals on surfactant-enhanced imbibition in shale reservoirs remains. Therefore, this study first analyzed the mineral composition and pore structure of the shale reservoirs. Subsequently, three surfactants were selected for spontaneous imbibition experiments. The influence of various clay minerals on the surfactant imbibition was assessed by considering various properties of the imbibition system. The results showed that the shale pores primarily consisted of macropores (44.03%) and mesopores (43.94%). Surfactants enhance the imbibition recovery by altering the wettability …

Investigation Of Co-Current And Counter-Current Multiphase Flow In Upstream Drilling And Production Applications, Hazem Fleifel

LSU Doctoral Dissertations

In the domain of upstream Petroleum Engineering, the dynamics of co-current and counter-current multiphase flows present huge challenges, significantly impacting the efficiency of associated processes. This study investigates two specific applications concerning these flow behaviors, involving both laboratory experiments and transient computer simulations. This work investigates two distinct well control and production enhancement processes, involving multiphase flow dynamics: the bullheading kill procedure and liquid-assisted gas lift (LAGL).

The first topic (Topic 1) explores the bullheading process, a type of well control methods, by challenging the traditional understanding that gas removal efficiency increases monotonically with injection pump flow rate. Through 1D …

Dissolution Mechanism Of Nonionic Polyether Surfactants In Supercritical Co2, Ning Xu, Yanling Wang, Baojun Bai, Shizhang Cui, Zan Gao, Yu Zhang, Di Li, Wenjing Shi, Wenhui Ding, Peixu Ma

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Polyoxyethylene ether is an efficient CO₂-philic compound with significant potential applications in CO₂ flooding, which requires CO₂-philic surfactants with high solubility in supercritical CO₂ (scCO₂). This study elucidates the molecular and atomic-level dissolution mechanism of the fatty alcohol polyoxyethylene ether (AEO) in scCO₂ by combining phase-behavior experiments and molecular dynamics simulations. The solubility of AEO in scCO₂ is measured using a semiconductor laser. AEO containing three polyoxyethylene (EO) groups exhibited the highest solubility in scCO₂.The solubility of AEO in scCO₂ decreased with an increase in the number …

Mantle Flow And Crustal Deformation Revealed By Seismic Anisotropy In The Subduction Zone Beneath Myanmar, Enbo Fan, Mingming Jiang, Yinshuang Ai, Stephen S. Gao, Kelly H. Liu, Yumei He, Yiming Bai, Guangbing Hou, Yuan Ling, Chit Thet Mon, Myo Thant, Kyaing Sein

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The oblique convergence of the Indian and Eurasian plates drives significant deformation in the crust and mantle beneath Myanmar. However, the crustal deformation in the Indo-Burman Ranges (IBR) and mantle flow beneath Myanmar and adjacent areas remain unclear due to limited studies. We utilized data from the newly deployed second phase of the China-Myanmar Geophysical Survey of the Myanmar Orogen array to perform shear wave splitting analysis of PKS, SKKS, and SKS (XKS) phases. Our results, together with previous findings, provide new insights into mantle flow and crustal deformation across central Myanmar. In the IBR, we observed a transition from …

Detection Of Oil Pollution On The Tigris River In Iraq Using Fluorescence And Reflecting Techniques, Ahmad K. Ahmad, Thamer M. Mohammed

Karbala International Journal of Modern Science

In this study, a broadband light source (visible and ultraviolet) was used to name minerals via fluorescence spectra and estimate slick oil thickness, ranging from sub-millimetres, using the reflecting spectrum technique. Using a fluorescent technique, we obtained fluorescence spectra of the samples, converting and processing the signals to produce high-resolution data, which enabled the identification of the types of dissolved elements and oil slicks in the Tigris River, highlighting pollution sources and potential control measures. This system aims to show the faint signal in fluorescence samples collected from the cooling system outlet water throughout the refining process from AL-Dora (Baghdad) …

Quantifying Wellbore Effects During Co2 Sequestration In A Saline Aquifer, Uzoma Johnpaul Ajugwe

USF Tampa Graduate Theses and Dissertations

Carbon capture and storage (CCS) is a strategy for mitigating climate change by reducing greenhouse gas emissions from large stationary sources like fossil-fuel-fired power stations. One method of CCS involves carbon dioxide (CO2) sequestration in deep saline aquifers, where supercritical CO2 is injected into an aquifer. The success of such projects depends on accurate predictions of CO2 behavior within the subsurface, which are obtained through numerical simulations.

TOUGHREACT, a renowned simulation tool, models subsurface fluid flow, geochemical interactions, and solute transport, providing insights into the feasibility of CO2 sequestration projects. A critical aspect of these simulations is the apportioning of …

Investigation Of Retention And Dehydration Of Preformed Particle Gel For Conformance Control In Fractured Carbonates, Abdulaziz A. Almakimi, Abdullah O. Almansour, Junchen Liu, Baojun Bai, Ibnelwaleed A. Hussein

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Preformed particle gel (PPG) treatment has proved to be among the most effective methods to reduce excessive water production in fractured reservoirs. The blocking ability of PPGs to fractures or fracture-like features is highly dependent on injected gel properties and volume. Gel dehydration during extrusion through fracture is common and has a considerable effect on gel properties, transport, and plugging efficiency. As the gel particles propagate through the fracture, continuous dehydration is often associated and causes the gel to concentrate and require high-pressure gradients to move. Dehydration might be desirable to a certain limit because it can help to form …

Effect Of Pre-Adsorbed Species On High-Pressure Adsorption Of Methane In Zeolite 5a Using Grand Canonical Monte Carlo (Gcmc) Simulations, Kanhamardi Lao, Brooks D. Rabideau

Shelby Hall Graduate Research Forum Posters

Natural gas upgrading, which removes impurities from methane (CH4), is essential for industrial applications, including liquefied natural gas (LNG) production and power generation, as well as for residential use. Removing non-hydrocarbon impurities such as carbon dioxide (CO2), nitrogen (N2), and water vapor (H2O), among others, along with separating heavier hydrocarbon gases from raw natural gas, is required to achieve high- purity methane and prevent pipeline corrosion. Zeolite 5A is a microporous aluminosilicate material with a pore size of approximately 5 Å, containing sodium and calcium cations that balance the framework’s negative charge. Its structure offers high thermal stability and a …

Reinforcing Polymer Flooding System With Dendritic Mesoporous Silica Nanoparticles For Improved Oil Recovery, Di Li, Yanling Wang, Baojun Bai, Ning Xu, Wenjing Shi, Yu Zhang, Wenhui Ding, Peixu Ma, Zan Gao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Dendritic mesoporous silica nanoparticles (DMSNs), characterized by a high specific surface area and abundant hydroxyl groups, offer a promising approach to enhancing the performance of amphiphilic polymers in challenging enhanced oil recovery (EOR) conditions. In this study, DMSNs were successfully synthesized, and systematically evaluated for their impact on the solution properties of a betaine amphiphilic polymer (PADC). The unique "flower-like" mesoporous structure of DMSNs provided approximately 7-fold higher surface area than conventional SiO2, facilitating enhanced polymer-nanoparticle interactions. The DMSN/PADC composite system exhibited significantly improved viscosity, salt resistance, thermal tolerance, and shear resistance compared to PADC and SiO2/PADC systems. Quantum chemical …

Using Preformed Particle Gels To Control Transport In Geothermal Reservoirs: Mathematical Modeling, Philip Winterfeld, Baojun Bai, Yu Shu Wu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

We are developing swellable Preformed Particle Gels (PPG), which can control preferential fluid and heat flow through fracture networks to increase the performance of EGS reservoirs. Part of this development is a mathematical model and numerical simulator to simulate PPG treatments by considering coupled thermal-hydraulic-mechanical effects, and gel swelling kinetics and plugging efficiency, from which an optimized gel treatment design and operation can be achieved. The starting point for our mathematical model is the TOUGH2-CSM formulation and code. The TOUGH2-CSM fluid and heat flow formulation is based on the TOUGH2 one for multiphase, multicomponent, and multi-porosity systems, with the latter …

Visual Understanding Of Rock Wettability Distribution To Contact Angle Regions And Oil Displacement Patterns In The Silty Sand Reservoir Via 2d Pore-Scale Modeling, H. Al-Ajaj, W. Al-Bazzaz, Ralph E. Flori, S. Alsayegh, H. Almubarak, D. S. Ibrahim, H. Al-Saedi

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study, conducted using a silty sand reservoir rock extracted from a Kuwait-producing oilfield, provides crucial insights into fluid distribution patterns and mineralogy, as well as wettability contact angle preferences. The method used for visual identification not only captures rock physics but also suggests effective oil recovery displacement strategies. Visual identification is presented using 2D image technology and a Scanning Electron Microscope (SEM). Analytical data are presented from electron bombardments and backscattering reflections collected in the BSE detector. These analyses were used to characterize the various surface boundary morphology parameters of the silty sand mineral surfaces, including area, perimeter, mineral …

Investigation Of Dynamic Adsorption And Desorption Of Polymer Nanogel In Porous Media Through Microfluidics, Junchen Liu, Fuqiao Bai, Abdulaziz A. Almakimi, Mingzhen Wei, Xiaoming He, Ibnelwaleed A. Hussein, Baojun Bai

Mathematics and Statistics Faculty Research & Creative Works

Understanding the transport and retention of elastic nanogel and microgel particles in porous media has been a significant research subject for decades, essential to the application of enhanced oil recovery (EOR). However, a lack of dynamic adsorption and desorption studies, in which the kinetics in porous media are seldom investigated, hinders the design and application of polymer nanogel in underground porous media. In this work, we visualized and quantified the transport and dynamic adsorption of polymer nanogel in 3D glass micromodels that were manufactured by packing glass beads in capillaries. Calibrating the linearity of fluorescence intensity to concentration, we calculated …

Predictive Modeling For Optimal Gel Treatment Design In Brownfields Using Ensemble Machine Learning And Data Upsampling Via Generative Ai, Munqith Aldhaheri, Baojun Bai, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Efficiently designed gel treatments play a vital role in extending the lifespan of brownfields through rejuvenating oil production. Recently, a three-mode mathematical methodology named the VCR approach has been proposed for designing effective treatments. To optimize this approach, it is crucial to determine the appropriate design mode systematically rather than relying solely on the intuitive judgments of field operators. This study introduces an advanced methodology for predicting the optimal design type of gel treatments using 12 reservoir and production variables. The methodology integrates ensemble machine-learning (EML) models with historical data from 65 field projects across 11 countries (1985-2020). The Random …

Physics-Informed Heterogeneous Spatiotemporal Graph Neural Network For Reservoir Simulation, Ahmed A.M.A. Abdullah

LSU Master's Theses

Reservoir simulation is the state-of-the-art method for predicting the flow of petroleum reservoir fluids in porous media. It provides an accurate and unbiased prediction of the performance of petroleum reservoirs under different operating conditions. Despite its advantages, reservoir simulation is computationally expensive; with typical full-field simulation models running for several hours. This limitation is worsened when simulating reservoirs with several equations for each cell, such as multiphysics or compositional reservoir simulation. The goal of this research is to provide a fast and accurate spatiotemporal machine-learning model that incorporates discretized governing mass balance equations for training. To achieve this, we propose …

Geochemical Evidence Of Drying During The 4.2 Ka Event In Sediment Cores From The Yucatán Peninsula, Mexico, Derek K. Gibson, Jonathan Obrist-Farner, Alex Correa-Metrio, Alejandra Rodriguez-Abaunza, Carlos Castañeda-Posadas

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Tropical hydroclimate variability during the Middle and Late Holocene was investigated using geochemical indicators of local-scale precipitation and evaporation preserved in sediment cores from two sites in the Mexican Yucatán Peninsula. Scanning X-Ray fluorescence spectroscopy data show generally decreasing precipitation trends during the Early and Middle Holocene. During the transition between the Middle and Late Holocene, geochemical evidence of reduced watershed erosion and increased evaporation indicate that a centennial-scale drying event impacted the region between 4.3 and 4.0 ka (kilo-anum; thousand years before present). These findings suggest that the 4.2 ka drying event, which has been previously recorded in Europe, …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

A Coarse-Grained Molecular Dynamics Study Of Gas Hydrate Formation And Dissociation, Meisam Adibifard

LSU Doctoral Dissertations

The study of gas hydrates has increased significantly over the last two decades because of their potential application in energy storage, production and transportation, water desalination, refrigeration, gas separation, etc. There is a significant interest in commercially developing natural gas hydrates because the energy content of methane hydrate reservoirs (MHRs) is at least twice that of all conventional fossil fuels combined. Additionally, due to the higher storage capacity of hydrates, it is proposed to sequester CO₂ in the form of CO₂ hydrate, thereby reducing the amount of greenhouse gases. Hence, hydrates offer a dual solution to two of …

A New Design Strategy For Sizes Of Polymer Gel Treatments Derived From A Comprehensive Assessment Of Their Case Histories, Munqith Aldhaheri, Abdullah Almansour, Na Zhang, Mingzhen Wei, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The incentive to revive brownfield oil production extends the interest to apply polymer gel treatments in injection wells. Virtually, volumes of previous remediations implemented in similar reservoir types are used to size new jobs. Such an analogy-Based design procedure imposes a need to evaluate the most frequent designs for each reservoir type based on a comprehensive field survey. This survey provides a new treatment sizing strategy for polyacrylamide-polymer bulk gels by reviewing their field applications in 653 injection wells. the new strategy proposes using the average and most frequent gel volumes per reservoir type as an initial estimate of the …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …