Membrane Science Commons^™

The Optimization And Manufacturing Scale-Up Of Polymeric Membranes Using Eco-Friendly Solvents, David Lu

Theses and Dissertations--Chemical and Materials Engineering

Polymeric membranes have become a prominent technology applied in water filtration due to the lower cost, energy input, and simpler manufacturing process relative to other separation technologies. However, the environmental impact of polymeric membrane fabrication remains a hindrance due to the use of hazardous solvents derived from fossil fuels (e.g., DMAc, NMP, DMF) that pose a risk to the environment and human health. Whereas recent studies have demonstrated the proof-of-concept of polymeric membrane derived from eco-friendly solvents, the next steps of optimizing and upscaling the production of these membranes remains understudied and a gap between lab-scale studies and the path …

Synthesis, Characterization, And Performance Assessment Of Reusable And Biodegradable Antimicrobial Polymeric Membranes For Aerosolized Pathogen Inactivation And Filtration, Ebuka Ogbuoji

Theses and Dissertations--Chemical and Materials Engineering

Air filtration technology has proven effective in purifying air by trapping particulates which can cause adverse health effects. High Efficiency Particulate Air (HEPA) filters, capable of capturing over 99.99% of PM_0.3, are recommended for critical applications. However, conventional non-woven HEPA filters rely on electrostatic interactions to trap smaller particles, which can deplete over time or after cleaning, reducing filtration efficiency and posing health risks. Additionally, these filters contribute to plastic waste.

This dissertation investigated the feasibility of using flat sheet polymeric membranes fabricated via nonsolvent-induced phase separation (NIPS) as reusable and biodegradable alternatives to commercially available non-biodegradable air …

Functionalized Microfiltration Membranes For Aerosol Capture To Chloro-Organic Degradation, Rollie George Mills

Theses and Dissertations--Chemical and Materials Engineering

The environmental remediation of water and air sources is a challenging field, due to widespread contamination, pollutant variety, and efficiency of existing treatment options. Remediation of certain pollutants, such as per- and polyfluorinated chemicals (PFAS), polychlorinated biphenyls (PCBs), volatile organic compounds (VOCs), and viral aerosols, has shown promise via adsorptive, degradative, or filtration-based processes, each with their respective advantages and limitations. Membrane technology is one option that has exhibited considerable pollutant removal from environmental sources via reverse osmosis (RO) filtration, but is limited by low permeabilities and lack of pollutant detoxification. With the support of NIEHS and NSF, the functionalization …

Exploring The Effect Of Casting Solution Composition, Additives, And Casting Conditions On The Morphology And Separation Performance Of Pvdf Membranes, Rachel Kaplan

Theses and Dissertations--Chemical and Materials Engineering

Global water scarcity and quality concerns in the past decade have led to a looming global water crisis. Polymeric membranes have emerged as a potential solution due to their modularity, operational reliability, and wide range of contaminant removal. Polyvinylidene fluoride (PVDF) is often selected as a membrane material for its enhanced chemical resistance, thermal stability, and mechanical strength. However, these membranes often require more complex fabrication methods or support materials to achieve optimum performance. Flat-sheet unsupported PVDF membranes were fabricated via nonsolvent induced phase separation. The influence of solvent, polymer composition, pore forming additives, and casting conditions were explored with …

Devices And Methods For Removing Perflourinated Compounds From Contaminted Water, Dibakar Bhattacharyya Phd, Anthony Saad Phd, Rollie Mills Phd, L. E. Ormsbee Phd, M Abdul Mottaleb Phd

Civil Engineering Faculty Patents

PFAS compounds have emerged as a persistent and harmful environmental pollutant that present significant challenges to health and remediation. This patent describes a new technology that employs membrane technology along with thermo-responsive adsorption-desorption processes to remove perfluorinated compounds from contaminate water.

Developing And Modeling Tunable Nanofiltration And Functionalized Membranes For The Separation Of Organics And Inorganics From Water: Per- And Polyfluoroalkyl Substances, Lanthanides, And More, Francisco Cecil Leniz-Pizarro

Theses and Dissertations--Chemical and Materials Engineering

In a world where clean water predictability is challenged by both global warming and the contamination of our natural resources, it is our responsibility to advance water separation technologies into more efficient processes and to lessen their environmental footprint. Pore and surface functionalization of membranes can enhance the separation of ions from water and even help overcome intrinsic challenges that some current separation technologies possess. If we begin with a complete fundamental understanding of the nanoscale interactions that occur in the process of separating ions from water, then we can engineer new functionalized composite membranes to provide alternative processes keeping …

Understanding Absorption, Supersaturation, And Drug Activity In Solution: Working Towards Developing A More Biorelevant Media, Freddy Arce

Theses and Dissertations--Pharmacy

With the looming dominance of poorly water-soluble chemical entities within the pharmaceutical pipeline, the pharmaceutical industry has leaned on the use of supersaturating drug delivery systems (SDDSs) to achieve efficacious concentrations within the gastrointestinal fluids. SDDSs aim to achieve concentrations in solutions greater than the solubility of the lowest energy crystalline form. However, the generation of supersaturated solutions of active pharmaceutical ingredients (APIs) creates a strong crystallization potential, which is undesirable.

In product development, supersaturating products often fail in Phase I and Phase II clinical trials due to poor oral bioavailability and a lack of in vivo efficacy. Pre-clinical testing …

Interactions Of Lignin Dimers With Engineered Surfaces And Model Cell Membranes For Design Of Lignin-Based Materials, Mahsa Moradipour

Theses and Dissertations--Chemical and Materials Engineering

Capitalizing on byproducts of industrial and agricultural economies is among the utmost goals of sustainability. Of particular interest for commercial upgrading is lignin, a phenolic biopolymer found in the cell walls of plants which is the second most abundant biopolymer on Earth after cellulose. Due to its heterogeneous structure, deconstructing lignin to selected small molecules for use as chemicals or advanced materials has been elusive. This work capitalizes on a “bottom up” approach to the synthesis of lignin oligomers of known bond chemistry to better understand their interfacial interactions.

The potential pharmacological mechanism of lignin deconstruction components and their toxicological …

Nanohybrid Membrane Synthesis With Phosphorene Nanoparticles: A Study Of The Addition, Stability And Toxicity, Joyner Eke, Philip Alexander Mills, Jacob Ryan Page, Garrison P. Wright, Olga V. Tsyusko, Isabel C. Escobar

Center of Membrane Sciences Faculty Publications

Phosphorene is a promising candidate as a membrane material additive because of its inherent photocatalytic properties and electrical conductance which can help reduce fouling and improve membrane properties. The main objective of this study was to characterize structural and morphologic changes arising from the addition of phosphorene to polymeric membranes. Here, phosphorene was physically incorporated into a blend of polysulfone (PSf) and sulfonated poly ether ether ketone (SPEEK) doping solution. Protein and dye rejection studies were carried out to determine the permeability and selectivity of the membranes. Since loss of material additives during filtration processes is a challenge, the stability …

Bimetallic Nanoparticles Integrated Membranes For Groundwater Remediation: Synthesis, Characterization And Applications, Hongyi Wan

Theses and Dissertations--Chemical and Materials Engineering

The detoxification of chlorinated organics from groundwater, such as trichloroethylene (TCE), tetrachloroethylene (PCE), polychlorinated biphenyl (PCB) and carbon tetrachloride (CTC), is a challenging area. Reductive dechlorination has been investigated using iron and iron-based nanoparticles, such as bare Fe, sulfidized Fe (S-Fe) and palladized Fe (Pd-Fe). However, issues including particle agglomeration, difficulties in recycling and particle leaching have been reported to hinder the application and wide usage of these techniques. The integration of nanoparticles and membranes can address these issues because of the large surface area, stability, and the potential for versatile functionalities. In this study, commercial polyvinylidene difluoride (PVDF) microfiltration …

Nanostructured Metal Thin Films As Components Of Composite Membranes For Separations And Catalysis, Michael J. Detisch

Theses and Dissertations--Chemical and Materials Engineering

Novel metallic thin film composite membranes are synthesized and evaluated in this work for improved separations and catalysis capabilities. Advances in technology that allow for improved membrane performance in solvent separations are desirable for low molecular weight organic separation applications such as those in pharmaceutical industries. Additionally, the introduction of catalytic materials into membrane systems allow for optimization of complex processes in a single step. By adding a nanostructured metallic thin film to its surface, a polymer membrane may be modified to exhibit these improved properties. Using magnetron sputtering, thin metal films may be deposited on commercially available membranes to …

Microfiltration Membrane Pore Functionalization Approaches For Chloro-Organic Remediation To Heavy Metal Sorption, Mohammad Saiful Islam

Theses and Dissertations--Chemical and Materials Engineering

Microfiltration polyvinylidene fluoride (PVDF) membranes have distinct advantage for open structure in terms of high internal surface area and ease of access in the pore domain. Functionalization of PVDF membranes with different functional groups (-COOH, -OH, -SH) enables responsive (pH, temperature) properties to membrane, tuning of effective pore size, controlling permeate flux. PVDF microfiltration membrane functionalization with suitable responsive polymer such as poly acrylic acid (PAA) to incorporate carboxyl (-COOH) group enables further modification of functionalized PAA-PVDF membranes for different application ranging from catalysis, bio reactor to heavy metal sorption platform. As a catalytic reactor bed, this PAA-PVDF membranes are …

The Development Of Temperature And Ph Responsive Hydrogels And Membranes For Selective Sorption Of Perfluoroorganics And Nanoparticle Integrated Catalytic Degradation Of Pcb, Anthony Saad

Theses and Dissertations--Chemical and Materials Engineering

The functionalization and use of responsive and catalytic polymeric membranes and materials were explored for contaminant capture and degradation. While membranes have a wide variety of uses across multiple industries, the inclusion of materials that are temperature and pH responsive in the membrane pore domain yields a wide range of applications and possibilities for water treatment. Temperature and pH responsive polymers, as well as controlled nanostructured materials, were synthesized in membrane pores for advanced adsorption-desorption and catalytic treatment of emerging organic contaminants in water. In this study, supported by the NIEHS, poly-N-isopropylacrylamide (PNIPAm) was used as a model thermo-responsive polymer, …

A Thermodynamic And Feasibility Study Of Green Solvents For The Fabrication Of Water Treatment Membranes, Xiaobo Dong

Theses and Dissertations--Chemical and Materials Engineering

Nonsolvent induced phase separation (NIPS) has been widely used to fabricate polymeric membranes. In NIPS, a polymer is dissolved in a solvent to form a dope solution, which is then cast on a substrate and immersed in a nonsolvent bath, where phase inversion occurs. Petroleum-derived organic solvents, such as N-Methyl-2-Pyrrolidone (NMP) and Dimethylacetamide (DMAc), have been traditionally used to fabricate polymeric membranes via NIPS. However, these solvents may have negative impacts on environmental and human health; therefore, using greener and less toxic solvents, preferably derived from biomass, is of great interest to make membrane fabrication sustainable. In this dissertation, two …

Polymeric Nanocomposite Membranes With Phosphorene Based Pore Fillers For Fouling Control, Joyner Eke

Theses and Dissertations--Chemical and Materials Engineering

Phosphorene is a two-dimensional material exfoliated from bulk phosphorus. Specifically, relevant to the field of membrane science, the band gap of phosphorene provides it with potential photocatalytic properties, which could be explored in making reactive membranes able to control the accumulation of compounds on the surface during filtration, or fouling. Another reason phosphorene is a promising candidate as a membrane material additive is due to its catalytic properties which can potentially destroy foulants on the membrane surface.

The first goal of this study was to develop an innovative and robust membrane able to control and reverse fouling with minimal changes …

Synthesis, Functionalization, And Application Of Nanofiltration And Composite Membranes For Selective Separations, Andrew Steven Colburn

Theses and Dissertations--Chemical and Materials Engineering

Future nanofiltration (NF) membranes used for selective separations of ions and small organic molecules must maintain performance in environments where high concentrations of total dissolved solvents or foulants are present. These challenges can be addressed through the development of composite membranes, as well as the engineering of enhanced surface properties and operating conditions for existing commercial membranes.

In this work, ion transport through commercial thin film composite (TFC) polyamide NF membranes were studied in both lab-prepared salt solutions and industrial wastewater. The dependence of several variables on ion rejection was investigated, including ion radius, ion charge, ionic strength, and temperature. …

Synthesis, Characterization And Applications Of Reduced Graphene Oxide And Composite Membranes For Selective Separations And Removal Of Organic Contaminants, Ashish Aher

Theses and Dissertations--Chemical and Materials Engineering

Among the next generation materials being investigated for membrane development, partially reduced Graphene Oxide (rGO) has received increasing attention from the membrane community. rGO-based nanofiltration membranes have shown promising results in applications such as partial desalination, organic contaminant removal, gas-phase separations, and separations from solvent media. rGO offers a unique platform compared to common polymeric membranes since it can be used for separation applications in both aqueous and organic solvent media. An rGO-based platform could also be utilized to synthesize reactive membranes, giving rGO membranes the additional capability of reactively removing organic contaminants. This research focuses on the synthesis of …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Mixed Matrix Flat Sheet And Hollow Fiber Membranes For Gas Separation Applications, Nicholas W. Linck

Theses and Dissertations--Chemical and Materials Engineering

Mixed matrix membranes (MMM) offer one potential path toward exceeding the Robeson upper bound of selectivity versus permeability for gas separation performance while maintaining the benefits of solution processing. Many inorganic materials, such as zeolites, metal-organic frameworks, or carbon nanotubes, can function as molecular sieves, but as stand-alone membranes are brittle and difficult to manufacture. Incorporating them into a more robust polymeric membrane matrix has the potential to mitigate this issue.

In this work, phase inversion polymer solution processing for the fabrication and testing of asymmetric flat sheet mixed matrix membranes was employed with CVD-derived multiwall carbon nanotubes (MWCNTs) dispersed …

Synthesis Of Biologically-Inspired Nanofiltration Membranes Using Protected, Mutated, And Simulated Aquaporins, Priyesh Ashokrao Wagh

Theses and Dissertations--Chemical and Materials Engineering

Gram-negative bacterial cells are surrounded by a cell membrane which protects the cell and controls the transport of nutrients and waste products in and out of the cells at a fast rate. This rapid transport of nutrients and wastes through the cell membrane is made possible by channel proteins called porins. Various types of porins present in the cell membrane have specific functions depending on their selectivity towards different nutrients, and channel proteins selective towards water are called aquaporins. These proteins restrict the passage of all entities except water molecules and they provide a fast transport rate of water molecules …

Layer-By-Layer Assembled Membranes With Immobilized Porins, Sebastián Hernández, Cassandra Porter, Xinyi Zhang, Yinan Wei, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

New and advanced opportunities are arising for the synthesis and functionalization of membranes with selective separation, reactivity, and stimuli-responsive behavior. One such advancement is the integration of bio-based channels in membrane technologies. By a layer-by-layer (LbL) assembly of polyelectrolytes, outer membrane protein F trimers (OmpF) or “porins” from Escherichia coli with central pores ∼2 nm in diameter at their opening and ∼0.7 × 1.1 nm at their constricted region are immobilized within the pores of poly(vinylidene fluoride) microfiltration membranes, in contrast to traditional ruptured lipid bilayer or vesicle processes. These OmpF-membranes demonstrate selective rejection of non-charged organics over ionic solutes, …

Tunable Nanocomposite Membranes For Water Remediation And Separations, Sebastián Hernández Sierra

Theses and Dissertations--Chemical and Materials Engineering

Nano-structured material fabrication using functionalized membranes with polyelectrolytes is a promising research field for water pollution, catalytic and mining applications. These responsive polymers react to external stimuli like temperature, pH, radiation, ionic strength or chemical composition. Such nanomaterials provide novel hybrid properties and can also be self-supported in addition to the membranes.

Polyelectrolytes (as hydrogels) have pH responsiveness. The hydrogel moieties gain or lose protons based on the pH, displaying swelling properties. These responsive materials can be exploited to synthesize metal nanoparticles in situ using their functional groups, or to immobilize other polyelectrolytes and biomolecules. Due to their properties, these …

Biomimetic Devices To Drive A Thermodynamically Uphill Reaction Using Light And To Degrade Industrial Waste Stream Components, Madison Joanne Sloan

Theses and Dissertations--Chemistry

Given the amount of industrial waste produced each year, as well as the accruing amount of greenhouse gases in our atmosphere produced by the burning of fossil fuels, it is imperative that humanity develop environmentally-sustainable sources of energy and methods of remediation. Nature achieves both of these by use of enzymes as catalysts, inspiring interest in designing biomimetic systems capable of harnessing clean energy and remediating industrial waste. This study examined the ability of enzymes in electrochemical and convective flow systems to achieve these tasks. The first portion studied the incorporation of enzymes into an electrochemical system to drive the …

Functionalization Of Silver Nanoparticles On Membranes And Its Influence On Biofouling, Conor G. Sprick

Theses and Dissertations--Chemical and Materials Engineering

Ultrafiltration (UF) processes are often used as pretreatment before more retentive/costly processes, such as nanofiltration and reverse osmosis. This study shows the results of low-biofouling nanocomposite membranes, loaded with casein-coated silver nanoparticles (casein-Ag-NPs). Membranes were cast and imbedded with Ag-NPs using two approaches, physical blending of Ag-NPs in the dope solution (^PAg-NP/CA membranes) and chemical attachment of Ag-NPs to cast membranes (^CAg-NP/CA membranes), to determine their biofouling control properties. The functionalization of Ag-NPs onto the CA membranes was achieved via attachment with functionalized thiol groups with the use of glycidyl methacrylate (GMA) and cysteamine chemistries. The …

Pore-Confined Carriers And Biomolecules In Mesoporous Silica For Biomimetic Separation And Targeting, Shanshan Zhou

Theses and Dissertations--Chemical and Materials Engineering

Selectively permeable biological membranes composed of lipophilic barriers inspire the design of biomimetic carrier-mediated membranes for aqueous solute separation. This work imparts selective permeability to lipid-filled pores of silica thin film composite membranes using carrier molecules that reside in the lipophilic self-assemblies. The lipids confined inside the pores of silica are proven to be a more effective barrier than bilayers formed on the porous surface through vesicle fusion, which is critical for quantifying the function of an immobilized carrier. The ability of a lipophilic carrier embedded in the lipid bilayer to reversibly bind the target solute and transport it through …

Development Of Pvdf Membrane Nanocomposites Via Various Functionalization Approaches For Environmental Applications, Douglas M. Davenport, Minghui Gui, Lindell E. Ormsbee, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

Membranes are finding wide applications in various fields spanning biological, water, and energy areas. Synthesis of membranes to provide tunable flux, metal sorption, and catalysis has been done through pore functionalization of microfiltration (MF) type membranes with responsive behavior. This methodology provides an opportunity to improve synthetic membrane performance via polymer fabrication and surface modification. By optimizing the polymer coagulation conditions in phase inversion fabrication, spongy polyvinylidene fluoride (PVDF) membranes with high porosity and large internal pore volume were created in lab and full scale. This robust membrane shows a promising mechanical strength as well as high capacity for loading …

Long Term Blood Oxygenation Membranes, Joseph V. Alexander

Theses and Dissertations--Biomedical Engineering

Hollow fiber membranes are widely used in blood oxygenators to remove carbon dioxide and add oxygen during cardiopulmonary bypass operations. These devices are now widely used off-label by physicians to perform extracorporeal blood oxygenation for patients with lung failure. Unfortunately, the hollow fiber membranes used in these devices fail prematurely due to blood plasma leakage and gas emboli formation.

This project formed ultrathin (~100nm) polymer coatings on polymer hollow fiber membranes. The coatings were intended to “block” existing pores on the exterior surfaces while permitting high gas fluxes. This coating is synthesized using surface imitated control radical polymerization.

The coating …

Biomolecule Localization And Surface Engineering Within Size Tunable Nanoporous Silica Particles, Daniel M. Schlipf

Theses and Dissertations--Chemical and Materials Engineering

Mesoporous silica materials are versatile platforms for biological catalysis, isolation of small molecules for detection and separation applications. The design of mesoporous silica supports for tailored protein and biomolecule interactions has been limited by the techniques to demonstrate biomolecule location and functionality as a function of pore size. This work examines the interaction of proteins and lipid bilayers with engineered porous silica surfaces using spherical silica particles with tunable pore diameters (3 – 12 nm) in the range relevant to biomolecule uptake in the pores, and large particle sizes (5 - 15 µm) amenable to microscopy imaging

The differentiation of …

Nanofiltration Membranes From Oriented Mesoporous Silica Thin Films, Mary K. Wooten

Theses and Dissertations--Chemical and Materials Engineering

The synthesis of mesoporous silica thin films using surfactant templating typically leads to an inaccessible pore orientation, making these films not suitable for membrane applications. Recent advances in thin film synthesis provide for the alignment of hexagonal pores in a direction orthogonal to the surface when templated on chemically neutral surfaces. In this work, orthogonal thin film silica membranes are synthesized on alumina supports using block copolymer poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (P123) as the template. The orthogonal pore structure is achieved by sandwiching membranes between two chemically neutral surfaces, resulting in 90 nm thick films. Solvent flux of ethanol through …

Functionalized Membranes For Environmental Remediation And Selective Separation, Li Xiao

Theses and Dissertations--Chemical and Materials Engineering

Membrane process including microfiltration (MF), ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) have provided numerous successful applications ranging from drinking water purification, wastewater treatment, to material recovery. The addition of functional moiety in the membranes pores allows such membranes to be used in challenging areas including tunable separations, toxic metal capture, and catalysis. In this work, polyvinylidene fluoride (PVDF) MF membrane was functionalized with temperature responsive (poly(N-isopropylacrylamide), PNIPAAm) and pH responsive (polyacrylic acid, PAA) polymers. It’s revealed that the permeation of various molecules (water, salt and dextran) through the membrane can be thermally or pH controlled. The introduction of …