Membrane Science Commons^™

Modern Ir-Spectroscopic Methods For The Analysis Of Hydroxybenzene-Methanal Resin Obtained On The Basis Of 2,5-Furandion, Sherali Anvarovich Umarov, Ravshan Israilovich Ismailov Ismailov

Technical science and innovation

The chemical changes occurring during the synthesis of hydroxybenzene-methanal resins obtained on the basis of 2,5-furandion under various ratios and temperature conditions were investigated using the IR spectroscopic method. Analysis of the compositional changes in the resin during the production of the thermoreactive resin revealed that the content of hydroxyl groups (~3300–3500 cm⁻¹) decreased, while the aldehyde groups (~1700–1750 cm⁻¹) increased; moreover, the presence of ether groups (~1050–1150 cm⁻¹) indicated that the process was successful. The synthesis of resins based on thermoreactive hydroxybenzene-methanal resins was carried out at high temperatures (70°C, 80°C, 95°C). During the identification of the functional groups …

Development Of Ex-Situ Accelerated Chemical Stress Test Protocol For Common Anionic Exchange Membrane Chemistries, Michael D. Friend, Michael D. Friend

Master's Theses

The development of sustainably produced hydrogen fuel (“green hydrogen”) is key for the transition to clean energy sources. Green hydrogen is produced via water electrolysis. As with many clean energy sources, one of the major barriers for scaling water electrolysis is cost. A newer category of water electrolysis is Anionic Exchange Membrane (AEM) water electrolysis. AEM electrolysis systems have the potential to cost less as they do not require the expensive precious metal catalysts the current high preforming Proton Exchange Membrane water electrolysis technologies do. However, AEM lifetimes must be long enough to be cost competitive and AEM chemical durability …

Synthesis Of Activated Carbon From Coconut Shell And Recycled Styrofoam Nanofiber For Water Filtration, Rahma Dani, Ismet Ismet, Leni Marlina, Rona Alisya, Muhamad Abel Kirana Aldi, Anggi Ludiansyah, Lintang Auliya Kurdiati, Meutia Kamilatun Nuha Ap Idjan, Agung Mataram, Muhammad Rama Almafie, Ida Sriyanti

Makara Journal of Science

Water pollution affects life sustainability; hence, several efforts have been exerted to overcome this problem. For ex-ample, nanofiber membrane technology is introduced to retain solutes while allowing only water molecules to pass through the system. Therefore, this study aimed to maximize the technology for water filtration using the electrospin-ning method by combining Styrofoam waste-based polymer with activated carbon from coconut shell waste (ACCS). The nanofiber diameter produced ranged from 590 nm to 610 nm with porous characteristics and without beads. The carbon content varied from 68.04% to 69.84%, according to the energy dispersive X-ray measurement, demonstrating the composite’s effectiveness. The …

Novel Membrane Materials For Nutrient Recovery From Nutrient-Rich Resources, Km Prottoy Shariar Piash

Graduate Theses, Dissertations, and Problem Reports (ETD)

Global demand for fertilizer production is expanding substantially to meet the food demand of an increasing world population. Anaerobic digestate (AD) of various centralized wastewater facilities contains substantial amounts of ammonium (NH₄⁺) (300-800 mg/L), potassium (K⁺) (13-120 mg/L), and phosphorus (P) (30-100 mg/L)- based nutrients. In addition to reducing energy costs and CO₂ emissions compared to conventional fertilizing raw material manufacturing, recovering nutrients from these waste streams could help mitigate problems such as eutrophication, which otherwise incurs billions of dollars losses to US economy annually. Apart from nutrients, wastewater streams also contain organic pollutants …

Development Of Novel Sensor Coating Methodology To Enable Understanding Of Fouling Mechanisms On Ion Exchange Membranes, Andrew Ulmer

Honors Theses

As populations expand and natural water resources are depleted, severe droughts and limited access to clean water have become an increased threat to areas across the world. Effective and economic water treatment methods such as electrodialysis (ED) are vital for combating these threats, especially in developing nations and secluded locations. Organic foulant adsorption on the surface of ion exchange membranes severely limits the capabilities of water desalination systems such as ED along with significantly increasing maintenance costs. Understanding characteristics such as the total amount and rate at which these foulants at specific concentrations adsorb and desorb to the membranes is …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver

Williams Honors College, Honors Research Projects

The project goal was to compare the food storage efficacy of sustainable beeswax wraps verses the single-use plastic methods of resealable plastic sandwich bags and plastic cling wrap. The goal was also to test the reusability of the beeswax wraps, as it is a key advantage of beeswax wraps that is advertised. The project purpose was to explore sustainable and eco-friendly alternatives to single use plastics, which are harmful to the environment in both their production and their disposal. Food spoilage was compared in beeswax wrap, plastic sandwich bags, and plastic cling wrap, and spoilage was also observed in a …

Fabrication Of Thin-Film Composite, Reverse-Osmosis Membranes With Polyethylenimine Modifications For Enhancing Membrane Fouling Resistance, Stephanie N. Hamilton

Master's Theses

Increasing water reuse opportunities for communities has become increasingly important as access to clean water is becoming more scarce. Reverse Osmosis (RO) is an advanced treatment technology used in water recycling wastewater for potable reuse applications. RO is a promising technology; however, the membranes have limitations including their high energy demand and their susceptibility to membrane fouling. The main objective of this study was to develop a reproducible method for the fabrication of RO membranes with enhanced flux and reduced susceptibility to fouling. Literature contains numerous publications on fabrication of thin film composite (TFC) RO membranes with high performance. However, …

Isolation And Production Of Tandem Collagen Binding Domain From Clostridial Collagenase Colg And Developments In C1q Reagent Production For Future Molecule Characterization Work, Stephanie Beitle

Chemical Engineering Undergraduate Honors Theses

This thesis covers a two part project: the production methods to create a double collagen binding domain molecule with a growth factor for wound healing applications and the development of a new in-house production method for isolating C1q from bovine blood. The wound healing molecule was created using transformation, sonication, and purification before being tested via electrophoresis SDS page and Western blots to confirm the molecule’s presence. The C1q in-house production method utilizes an ultrafiltration flow cell rather than dialysis at a critical point in the process, allowing for researchers to not only be able to use a single small …

Synthesis And Phase Transition Characterization Of Liquid Crystal Membranes With Slit-Like Pores, Isaac Hopwood

Chemical Engineering Undergraduate Honors Theses

Membranes with slit-like pores have been of interest for some time due to their ability to reject smaller particles than traditional cylindrical-pored membranes at the same fluid flux. However, using liquid crystals as a template for this sort of membrane has not been thoroughly investigated. In this study, the liquid crystal mixture of RM257 (2-Methyl-1,4-phenylene bis(4-(3-(acryloyloxy)propoxy)benzoate)) and 5CB (4-Cyano-4'-pentylbiphenyl) for the purpose of manufacturing membranes with slit-like pores, the phase transition behavior of this LC mixture at various mole fractions of RM257, and the impact of mole fraction of RM257 in the liquid crystal (LC) mixture and membrane manufacturing conditions …

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Tuning Electrochemical Interactions And Polymer Electrolyte Interfaces For Enhanced Organic Acid Separations Using Electrodeionization, Matthew Leo Jordan

LSU Doctoral Dissertations

Chemical separations are critical processes for chemical and industrial plants to purify and isolate products however current separation technologies, such as distillation, rely on energy intensive processes. Electrochemical separation processes, such as electrodialysis and electrodeionization, are an energy efficient alternative that are emerging as an alternative for thermal-based separations. Organic acids are weakly ionizable species and susceptible for purification from process streams using electrochemical processes. Recently the fermentation route has garnered greater attention as a means for producing value-added chemicals, such as organic acids, from a renewable feedstock and aiding the circular economy. Some of the challenges electrodialysis faces for …

Combinatorial Approaches For Effective Design, Synthesis, And Optimization Of Enzyme-Based Conjugates, Jordan Scott Chapman

Graduate Theses, Dissertations, and Problem Reports (ETD)

The specificity and efficiency with which enzymes catalyze selective chemical reactions far exceeds the performance of traditional heterogeneous catalysts that are predominant in industrial applications such as conversion of commodity chemicals to value-added products, fuel cells, and petroleum refinement. Moreover, biocatalysts exhibit exceptionally high product turnover at ambient conditions with little health and environmental burden. These advantageous qualities have led to the prolific use of enzyme catalysis in pharmaceutical, detergents, and food preservation industries wherein their use has greatly reduced waste generation, Unfortunately, the full slate of benefits that enzymes can impart to a broader range of chemical processes is …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

Alumina Ceramic Membrane Incorporated With Graphene Oxide Frameworks For Protein Recovery, Ishak Noor Fauziyah

Student Works (2020-2029)

Alumina ceramic membrane is undergoing rapid development and innovation for protein recovery process. However, the limitation of this membrane type is membrane fouling due to the deposition and adsorption of proteins on the surface and pore walls of the membranes. It is crucial to minimize membrane fouling by reducing interactions between protein and the membrane surface via surface modification technique. Thus, the main objective of this research is to develop an alumina membrane with enhanced antifouling property for protein recovery process. An alumina dope consisting of 57 wt.% alumina loading was used to fabricate two alumina membrane configurations; which are …

Peptoid And Antibody-Based Gfp Sensors, Solomon Isu

Graduate Theses and Dissertations

In this work, we have made and characterized a pair of immunobiosensors for detecting the green fluorescent protein (GFP) in an aqueous matrix. An anti-GFP antibody-based biosensor was assembled to detect GFP, while a novel peptoid (N-substituted oligomers of glycine designated as IOS-1) biosensor was also assembled for GFP detection. A quartz crystal microbalance (QCM) gold sensor was used as the supporting substrate for self-assembly of the immunobiosensors. Gravimetric measurements of the QCM gold sensor during immunobiosensor construction and operation were available in real-time using a QCM instrument. X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Fluorescence microscopy were used …

Nanostructured Metal Thin Films As Components Of Composite Membranes For Separations And Catalysis, Michael J. Detisch

Theses and Dissertations--Chemical and Materials Engineering

Novel metallic thin film composite membranes are synthesized and evaluated in this work for improved separations and catalysis capabilities. Advances in technology that allow for improved membrane performance in solvent separations are desirable for low molecular weight organic separation applications such as those in pharmaceutical industries. Additionally, the introduction of catalytic materials into membrane systems allow for optimization of complex processes in a single step. By adding a nanostructured metallic thin film to its surface, a polymer membrane may be modified to exhibit these improved properties. Using magnetron sputtering, thin metal films may be deposited on commercially available membranes to …

Nano-Enhanced Composite Membranes For Water Desalination, Benjamin Fredrik Victor Sundling Von Fürstenrecht

Materials Engineering

In theory single walled carbon nanotubes (SWCNT) will aid in ion rejection due hydrophobicity and smoothness of the SWCNT. An efficient means of water desalination utilizing SWCNT in a membrane seems plausible. A lyotropic liquid crystal (LLC) solution was made with a synthesized polymerizable surfactant methacryloxy ethyl hexadecyl dimethyl ammonium bromide (C16MA) to help with vertical alignment of SWCNT. Due to SWCNT lack of solubility and tendency to agglomerate in water, a dispersion performed using an inert surfactant centrimonium bromide (CTAB) to make sure that the SWCNT were homogeneously dispersed in the solution without altering the hexagonal packing factor of …

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

Mixed Matrix Flat Sheet And Hollow Fiber Membranes For Gas Separation Applications, Nicholas W. Linck

Theses and Dissertations--Chemical and Materials Engineering

Mixed matrix membranes (MMM) offer one potential path toward exceeding the Robeson upper bound of selectivity versus permeability for gas separation performance while maintaining the benefits of solution processing. Many inorganic materials, such as zeolites, metal-organic frameworks, or carbon nanotubes, can function as molecular sieves, but as stand-alone membranes are brittle and difficult to manufacture. Incorporating them into a more robust polymeric membrane matrix has the potential to mitigate this issue.

In this work, phase inversion polymer solution processing for the fabrication and testing of asymmetric flat sheet mixed matrix membranes was employed with CVD-derived multiwall carbon nanotubes (MWCNTs) dispersed …

Membranes For Food And Bioproduct Processing, Alexandru Marius Avram

Graduate Theses and Dissertations

Modified membranes for process intensification in biomass hydrolysis

Production of biofuels and chemicals from lignocellulosic biomass is one of the leading candidates for replacement of petroleum based fuels and chemicals. However, conversion of lignocellulosic biomass into fuels and chemicals is not cost effective compared to the production of fuels and chemicals from crude oil reserves. Some novel and economically feasible approaches involve the use of ionic liquids as solvents or co-solvents, since these show improved solvation capability of cellulose over simple aqueous systems. Membranes offer unique opportunities for process intensification which involves fractionation of the resulting biomass hydrolysate leading to …

Tunable Nanocomposite Membranes For Water Remediation And Separations, Sebastián Hernández Sierra

Theses and Dissertations--Chemical and Materials Engineering

Nano-structured material fabrication using functionalized membranes with polyelectrolytes is a promising research field for water pollution, catalytic and mining applications. These responsive polymers react to external stimuli like temperature, pH, radiation, ionic strength or chemical composition. Such nanomaterials provide novel hybrid properties and can also be self-supported in addition to the membranes.

Polyelectrolytes (as hydrogels) have pH responsiveness. The hydrogel moieties gain or lose protons based on the pH, displaying swelling properties. These responsive materials can be exploited to synthesize metal nanoparticles in situ using their functional groups, or to immobilize other polyelectrolytes and biomolecules. Due to their properties, these …

Functionalization Of Silver Nanoparticles On Membranes And Its Influence On Biofouling, Conor G. Sprick

Theses and Dissertations--Chemical and Materials Engineering

Ultrafiltration (UF) processes are often used as pretreatment before more retentive/costly processes, such as nanofiltration and reverse osmosis. This study shows the results of low-biofouling nanocomposite membranes, loaded with casein-coated silver nanoparticles (casein-Ag-NPs). Membranes were cast and imbedded with Ag-NPs using two approaches, physical blending of Ag-NPs in the dope solution (^PAg-NP/CA membranes) and chemical attachment of Ag-NPs to cast membranes (^CAg-NP/CA membranes), to determine their biofouling control properties. The functionalization of Ag-NPs onto the CA membranes was achieved via attachment with functionalized thiol groups with the use of glycidyl methacrylate (GMA) and cysteamine chemistries. The …

Designed Synthesis Of Nanoporous Organic Polymers For Selective Gas Uptake And Catalytic Applications, Pezhman Arab

Theses and Dissertations

Design and synthesis of porous organic polymers have attracted considerable attentions during the past decade due to their wide range of applications in gas storage, gas separation, energy conversion, and catalysis. Porous organic polymers can be pre-synthetically and post-synthetically functionalized with a wide variety of functionalities for desirable applications. Along these pursuits, we introduced new synthetic strategies for preparation of porous organic polymers for selective CO₂ capture.

Porous azo-linked polymers (ALPs) were synthesized by an oxidative reaction of amine-based monomers using copper(I) as a catalyst which leads to azo-linkage formation. ALPs exhibit high surface areas of up to 1200 …

Effect Of Plasticizer On Oxygen Permeability Of Cast Polylactic Acid (Pla) Films Determined Using Dynamic Accumulation Method, Kurniawan Yuniarto, Bruce A. Welt, Aris Purwanto, Hadi Karia Purwadaria, Ayman Abdellatief, Titi C. Sunarti, Setyo Purwanto

Journal of Applied Packaging Research

Polylactic acid (PLA) is becoming an increasingly important biopolymer for packaging applications. PLA brittleness limits its applicability. This study evaluated PLA properties with increasing amounts of added polyethylene glycol (PEG) plasticizer. Oxygen transmission rate (OTR) of cast films was determined using the newly available Dynamic Accumulation (DA) method. Arrhenius temperature sensitivity of OTR and polymer Permeability was also determined. Permeability of neat PLA is 4.848 ml mm (STP)/m² s kPa; hence, 4.84 ml mm (STP)/m² s kPa, 4.07 ml mm (STP)/m² s kPa and 5.42 ml mm (STP)/m² s kPa by adding PEG 1 %, 5% …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …