Membrane Science Commons^™

Experimental Evaluation Of Membranes In The Recovery Of Hydrogen From Serpentinization, Rafael Dos Santos

LSU Master's Theses

Natural hydrogen generated through serpentinization reactions has emerged as a promising low-carbon energy resource. However, serpentinization-derived gas streams commonly contain methane (CH₄) and carbon dioxide (CO₂), requiring purification before hydrogen can be utilized in industrial applications. Membrane-based gas separation technologies offer a potentially cost-effective solution for hydrogen recovery; however, to the best of the author's knowledge, no previous studies have specifically investigated their application to serpentinization-derived gas streams.

This work evaluates the performance of two commercial polymeric membrane modules (Evonik and Generon) and one palladium-copper (Pd-Cu) membrane module (Okaya) for hydrogen recovery from gas compositions representative of serpentinization environments. An …

Optimization And Dft Study For Boosted Electooxidation Of Formic Acid At Niox Modified Pt Using Urea Derivatives As Blending Fuels, Aya Saada

Biochemical Engineering

This paper addresses the enhancement of formic acid electrooxidation (FAO) at Pt and Pt-NiOx nanoparticles based-catalysts assisted with urea derivatives as blending fuels. Blending formic acid with various ratios of urea derivatives showed noticeable enhancements of FAO as demonstrated by a favorable negative shift of its onset potential (Eonset) and increase of its peak current density concurrently with suppression of the amount of CO poisoning reaction intermediate. Among all the used derivatives, phenyl urea (PU) showed superior enhancing effect towards the direct FAO with a minimal CO formation together with a favorable negative shift of Eonset by 150 mV. The …

Integrating Medical Plastic Waste Pyrolysis And Circular Economy For Environmental Sustainability, Attia Attia, Mohamed Bassyouni Prof., Reem Nasser Eng., Moataz El-Bagoury Eng., Islam Shaker Eng., Yasser Elhenawy Prof., Dina Aboelela Dr.

Biochemical Engineering

A critical assessment of pyrolysis technologies and reactor designs was discussed, highlighting various reactor configurations. This study explored the influence of catalysts, temperature, heating rate, and residence time on the pyrolysis process, and addressed their effects on product distribution and composition. Safety considerations and strategies for mitigating the potential environmental impacts of pyrolysis were presented. Comparative analyses of the environmental impacts of traditional waste disposal methods versus pyrolysis-based approaches provided insights into the potential reduction of greenhouse gas emissions and other pollutants. The circular economy approach was explored in the context of medical plastic waste pyrolysis. The potential for closing …

Electrified Membrane For Water Treatment And Resource Recovery: Advancing Multiscale Strategies In Gas-Involving Reactions, Jianan Gao

Dissertations

Multifunctional, modular, and scalable water treatment technologies that operate without chemical additives are crucial for addressing global water pollution challenges. While traditional membrane-based separation processes are crucial for ensuring clean water supplies, they primarily focus on pollutant removal rather than on the upcycling of pollutants into valuable resources. Electrified membrane filtration presents a robust alternative, utilizing minimal or no chemical additives and harnessing electrical power to directly reduce contaminants or produce reactive oxidants or reductants on-site.

This dissertation is dedicated to the development of innovative electrochemically reactive membranes designed to address three major challenges: (1) the engineering of electrocatalysts with …

Process Simulation For Converting Co2 Emissions From The Cementindustry To Dimethyl Ether, Nour Abou Seada, Dina Aboelela

Biochemical Engineering

Climate change is the leading severe problem in the twenty-first century, which is associated with greenhouse gas emissions,carbon dioxide that is the foremost cause of global warming and super greenhouse effect. In this concern, to avoid hazardousproblems, the steady stream of CO2 effluents existing in the atmosphere must be transformed to beneficial products for beingused as an abundant chemical feedstock. Implementing a new green strategy, which is known for the catalytic hydrogenationof CO2 into alternative fuels and valuable chemicals, will be a long-lasting solution to alleviate CO2 emissions. In this paper,a process simulation showing the synthesis of dimethyl ether (DME) …

Hydrogen Production From Microbial Electrolysis Cells Powered With Microbial Fuel Cells, Dina Aboelela

Biochemical Engineering

No abstract provided.

Design And Implementation Of Portable Power And Desalination Units Powered By Renewable Energy, Mo'ath A. Massad

Mechanical Engineering Theses

Freshwater scarcity is a critical global issue, especially in remote areas or areas impacted by natural disasters. Water desalination is one of the most effective methods to provide fresh water where it is needed. However, large-scale desalination plants cannot provide fresh water in the case of a natural disaster far from the plant's location. To address this, portable desalination units powered by renewable energy sources can be developed to supply potable water and power as a by-product for emergency situations. This work explored the application of different desalination methods, including reverse osmosis (RO) and electrodialysis (ED), in conjunction with renewable …

Nanoscale Modeling Of Membrane Systems Under Mechanical Deformation In Traumatic Brain Injury Using Molecular Dynamics, Anh Thi Ngoc Vo

Theses and Dissertations

Neuronal membrane disruption and mechanoporation are nanoscale damage mechanisms that critically affect brain cell viability during traumatic brain injury (TBI). These nanoscale cellular impairments are elusive in experiments and necessitate in silico approaches such as molecular dynamics (MD) simulations. Implementing MD, this research aims to investigate the effects of different key factors related to membrane deformation and damage, including force field resolutions, lipid compositions, and loading conditions.

To examine the impact of force field resolution, MD deformation simulations were conducted on 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) lipid bilayer membranes, using all-atom (AA), united-atom (UA), and coarse-grained Martini (CG-M) force fields. The mechanical responses …

Impact Of Spray Coating On The Performance Of Hydrophobic Membranes, Dominick J. Maiorano, Hamid Fattahijuybari, David Warsinger

Discovery Undergraduate Interdisciplinary Research Internship

Membrane distillation (MD) is a rapidly emerging water treatment technology used to combat the global water crisis. Membrane pore wetting is a primary barrier to widespread industrial use of MD. The primary causes of membrane wetting are membrane fouling and an exceedance of liquid entry pressure. The development of different types of polymer membranes and the use of pretreatment have led to significant movement towards the prevention of wetting in MD. We sought to take a new approach to combat membrane wetting that involves coating these membranes with hydrophilic chemical compounds, which consequently would decrease their air permeability. Pulling data …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Exergetic Relationship Between The Thermal Properties Of Direct Contact Membrane Distillation, D. Perdue, L. Chen, L. Schaefer

Publications

Direct contact membrane distillation (DCMD) is a process that has shown promise within the field of desalination due to its less energy intensive methods and widespread applications. DCMD is a thermally driven microfiltration separation process that operates on the principle of vapor–liquid equilibrium conditions where heat and mass transfer occur simultaneously. Fundamentally, DCMD is based on a porous hydrophobic membrane separating the hot solution (feed) from the cold solution (permeate) where desalinated water condenses. The membrane interfacial temperatures determine the vapor pressure difference across the membrane. In this work, a direct simulation Monte Carlo analysis is employed to investigate how …

Capillary Forces In Partially Saturated Thin Fibrous Media, Ali Moghadam

Theses and Dissertations

Capillarity is often exploited in self-cleaning, drag reducing and fluid absorption/storage (sanitary products) purposes just to name a few. Formulating the underlying physics of capillarity helps future design and development of optimized structures. This work reports on developing computational models to quantify the capillary pressure and capillary forces on the fibrous surfaces. To this end, the current study utilizes a novel mass-spring-damper approach to incorporate the mechanical properties of the fibers in generating virtual fibrous structures that can best represent fibrous membranes. Such virtual fibrous structures are then subjected to a pressure estimation model, developed for the first time in …

Modeling Electrospun Fibrous Materials, Sina Hassanpouryousefi

Theses and Dissertations

Electrospinning has been the focus of countless studies for the past decades for applications, including but not limited to, filtration, tissue engineering, and catalysis. Electrospinning is a one-step process for producing nano- and/or micro-fibrous materials with diameters ranging typically from 50 to 5000 nm. The simulation algorithm presented here is based on a novel mass-spring-damper (MSD) approach devised to incorporate the mechanical properties of the fibers in predicting the formation and morphology of the electrospun fibers as they travel from the needle toward the collector, and as they deposit on the substrate. This work is the first to develop a …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Design And Commissioning Of A Community Scale Solar Powered Membrane-Based Water Purification System In Haiti, Shavin Pinto, Yung Wong, Kyle Fennesy, Yan Tang, Marc Compere

Publications

This paper presents the design and commissioning of a solar powered water purification system at the Ryan Epps Home for Children (REHC) in Michaud, Haiti. This system supplies clean drinking water to the 200 children who live and go to school at REHC and also to the community in the form of a micro-business. This micro-business is the mechanism for income generation for sustainable system operation. The purifier uses a three stage filtration system with a disc-type sediment filter, a 0.1 micron ultrafiltration membrane, and an ultraviolet light for disinfection. The backwash cycle extends the life of the ultrafiltration membrane …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Mechanical Characterization Of Polymer Electrolyte Membrane With Optical Methods, Xinyu Huang, Luis Alva, Jay Neutzler

Faculty Publications

Mechanical properties of polymer electrolyte membrane have important implications in the endurance of many electrochemical energy conversion devices [1]. Mechanical experiments are effective method to reveal discrete damage developed in the membrane by quantifying the change of mechanical strength and toughness. Regular strain measurement methods are overly intrusive to the thin and relatively fragile polymer electrolyte membrane; hence optical-based minimal invasive stress/strain measurement methods are studied.

Mechanics-Based Model For Non-Affine Swelling In Perfluorosulfonic Acid (Pfsa) Membranes, Ahmet Kusoglu, Michael H. Santare, Anette M. Karlsson

Mechanical Engineering Faculty Publications

A mechanics-based model is developed to predict the swelling pressure in perfluorosulfonic acid (PFSA) ionomer membranes during water uptake. The PFSA membrane is represented as a two-phase system, where the water-filled hydrophilic domains are dispersed throughout the hydrophobic polymer matrix. Two representative volume elements (RVEs) are used to represent the nanostructure: (i) a spherical RVE with a spherical hydrophilic domain at the center, and (ii) a cylindrical RVE with a cylindrical hydrophilic domain. The model starts with the non-affine swelling behavior of the membrane and interprets this as a structural reorganization of the RVEs to characterize the microscopic deformation. Swelling …

Stress-Strain Behavior Of Perfluorosulfonic Acid Membranes At Various Temperatures And Humidities: Experiments And Phenomenological Modeling, Ahmet Kusoglu, Yaliang Tang, Michael Santare, Anette M. Karlsson, Simon Cleghorn, William B. Johnson

Mechanical Engineering Faculty Publications

The constitutive response of perfluorinated sulfonic acid (PFSA) membranes based on tensile testing is investigated, and a phenomenological constitutive model for the elastoplastic flow behavior as a function of temperature and humidity is proposed. To this end, the G'Sell–Jonas (1979, “Determination of the Plastic Behavior of Solid Polymers at Constant True Strain Rate,” J. Mater. Sci., 14, pp. 583–591) constitutive model for semicrystalline polymers is extended by incorporating, in addition to temperature, relationships between the material constants of this model and the measured relative humidity. By matching the proposed constitutive model to the experimental stress-strain data, useful material constants …

Inhomogeneous Degradation Of Polymer Electrolyte Membrane In Pem Fuel Cells, Xinyu Huang, Wonseok Yoon

Faculty Publications

Membrane durability is one of the technical barriers for the commercialization of polymer electrolyte membrane (PEM) fuel cells. Membrane embrittlement (a form of mechanical weakening) can lead to the frequently observed “sudden death” behavior of PEM fuel cells. It is the objective of this study to explore the fundamental mechanisms of the mechanical weakening of perfluorosulfonic acid (PFSA) based electrolyte membranes during the accelerated degradation test.

Micromechanics Model Based On The Nanostructure Of Pfsa Membranes, Ahmet Kusoglu, Michael H. Santare, Anette M. Karlsson, William B. Johnson, Simon Cleghorn

Mechanical Engineering Faculty Publications

A micromechanics model is developed to predict Young’s modulus of perfluorosulfonic acid (PFSA) membranes at various temperatures and water contents. The morphology of PFSA membranes is characterized by a two-phase structure, where hydrophilic clusters expand to hold water molecules during swelling, whereas the hydrophobic polymer network maintains the structural stability. A representative volume element (RVE) is proposed based on the descriptions for the nanostructure of PFSA membranes available in the literature. On the basis of mechanics model, we estimate Young’s modulus in tension of PFSA membranes as a function of water volume fraction for various temperatures. The results show that …

Thermodynamic Analysis Of Separation Systems, Yaşar Demirel

Papers in Thermal Mechanics

Separation systems mainly involve interfacial mass and heat transfer as well as mixing. Distillation is a major separation system by means of heat supplied from a higher temperature level at the reboiler and rejected in the condenser at a lower temperature level. Therefore, it resembles a heat engine producing a separation work with a rather low efficiency. Lost work (energy) in separation systems is due to irreversible processes of heat, mass transfer, and mixing, and is directly related to entropy production according to the Gouy-Stodola principle. In many separation systems of absorption, desorption, extraction, and membrane separation, the major irreversibility …