Catalysis and Reaction Engineering Commons^™

Investigation Of Light Management Strategies And Photochemistry Of Si/Tio2 Tandem Microwire Slurries For Solar Hydrogen Generation., Saumya Gulati

Electronic Theses and Dissertations

The intermittent nature of the Sun makes it difficult to use it as a primary source of electricity and often needs to be supplemented by electricity from the grid which comes from fossil fuels. This motivates the need for solar energy storage. Photoelectrochemical (PEC) water-splitting has been explored as a means to convert solar energy into hydrogen (and oxygen), which can be stored as fuel. The current method of coupling PV and electrolyzer units has been widely commercialized, however, the cost of H₂ generated is far from the target of $1/kg set by the DOE under the Energy EarthShot …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

A Molecular Dynamics Study Of Structural Modifications Of Perarylphosphonium Based Ionic Liquids On The Melting Point, Johnathan Anderson

Graduate Theses and Dissertations (2019 - present)

Several perarylphosphonium based mesothermal ionic liquids (ILs) have been shown to be stable at high temperatures for prolonged periods of time and with high heat capacities making them good candidates for use in many processes such as usage as a heat transfer fluid, as an absorbent for separation of aromatics from aliphatics, and as a solvent for high temperature reactions. Many, however, have melting points above 100^o C, limiting their use. Recently, it was shown that the melting point of an IL can be lowered by simply increasing the dipole moment of the cation or by structurally rigidifying the …

Hydrothermal Liquefaction Of Saccharina Latissima For The Production Of Biofuel, Mayokun A. Oke

Mechanical Engineering Theses

We performed hydrothermal liquefaction of brown macroalga (Saccharina latissima) in the presence of homogenous and heterogenous catalysts such as KOH, Na₂CO₃, Pd/C, HZSM-5, Ce/HZSM-5, and Ni/SiO₂-Al₂O₃ in hot compressed water, to investigate their effects on product yield and composition in the biocrude. To investigate hydrocarbon production, we used methanol as co-solvent (methanol-to-water 1/4 vol.%) and as the only liquefaction solvent. We carried out the experiments in a batch reactor at 330^oC and 120-130 bar, and varying temperature, algae-to-water ratio, residence time, and pretreatment method. The biocrude yields …

Improved Selectivity And Stability In Methane Dry Reforming By Atomic Layer Deposition Onto Ni-Ceo2-Zro2/Al2o3 Catalysts, Jonathan Lucas

LSU Master's Theses

The use of Ni in the dry reforming of methane (DRM) has been widely studied as a replacement for noble metal catalysts (Pt, Pd, Rh) due to Ni’s low cost compared to noble metals, its abundance, and the fact that its DRM activity is near that of noble metal catalysts. However, Ni has been shown to deactivate quickly under DRM conditions. Rare earth oxides such as CeO₂, or as CeO₂-ZrO₂ (CZO) are supports that improve both the activity and stability of Ni DRM systems due to their redox activity. However, this same activity is thought …

Bimetallic Compound Catalysts With Multiple Active Centers For Accelerated Polysulfide Conversion In Li-S Batteries, Wu-Xing Hua, Jing-Yi Xia, Zhong-Hao Hu, Huan Li, Wei Lv, Quan-Hong Yang

Journal of Electrochemistry

Practical applications of lithium-sulfur (Li-S) batteries are hindered mainly by the low sulfur utilization and severe capacity fading derived from the polysulfide shuttling. Catalysis is an effective remedy to those problems by promoting the conversion of polysulfides to reduce their accumulation in the electrolyte, which needs the catalyst to have efficient adsorption ability to soluble polysulfides and high activity for their conversion. In this work, we have proposed a bimetallic compound of NiCo₂S₄ anchored onto sulfur-doped graphene (NCS@SG) to fabricate a catalytic interlayer for Li-S batteries. Compared to CoS, the NiCo₂S₄ demonstrated much higher …

Advances And Challenges On Cathode Catalysts For Lithium-Oxygen Batteries, Bo Wen, Zhuo Zhu, Fu-Jun Li

Journal of Electrochemistry

Aprotic lithium-oxygen batteries (LOBs) with high theoretical energy density have received considerable attention over the past years. However, the oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) at cathodes suffer from slow kinetics for large overvoltages in LOBs. Significant advances on catalysts have been achieved to accelerate cathode kinetics, but understanding on the formation/decomposition processes of Li₂O₂ is limited. Herein, this review highlights the fundamental understanding of the correlation between catalysts and formation/decomposition of Li₂O₂. Various types of cathode catalysts are discussed to reveal the mechanism of formation/decomposition of Li₂O₂, …

Recent Advances In Anode Materials Of Solid Oxide Electrolysis Cells, Geng Zou, Wei-Cheng Feng, Yue-Feng Song, Guo-Xiong Wang

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) as an electrochemical energy conversion device has attracted increasing attention due to its large current density, high Faradaic efficiency and energy efficiency. Oxygen evolution reaction at the anode, a four-electron transfer process, is an important half-reaction for SOEC, which contributes to the main polarization resistance and consumes most electric energy during the electrolysis process. Hence, designing anode materials with high activity and stability is crucial for the performance improvement and practical application of SOEC. Recently, some advances have been made in the development of high-performance anode. In the current review, the mechanisms for CO_{2 …}

Anodic Electrocatalysis Of Glycerol Oxidation For Hybrid Alkali/Acid Electrolytic Hydrogen Generation, Xin Feng, Bo-Wen Liu, Ke-Xin Guo, Lin-Feng Fan, Gen-Xiang Wang, Su-Qin Ci, Zhen-Hai Wen

Journal of Electrochemistry

Electrolytic hydrogen production is heavily restricted by high-energy consumption majorly due to the relatively high potential of anodic oxygen evolution reaction (OER). Development of OER-alternative reaction at the anode has been recently proposed as a promising pathway to address the associated issues. In this work, we report a hybrid acid/alkali dual-electrolyte electrolyzer by coupling acidic hydrogen evolution reaction (HER) using commercial Pt/C cathode with alkaline Electrocatalytic glycerol oxidation (GOR) which is implemented by developing a nickel foam (NF) supporting Co₃O₄ nanosheets anode that shows low overpotential and high selectivity toward GOR for formate production. The hybrid acid/alkali …

Preface To Special Issue On Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Highly Dispersed Pt Nanoparticles Root In Single-Atom Fe Sites In Ldhs Toward Efficient Methanol Oxidation, Qing-Cheng Meng, Lin-Bo Jin, Meng-Ze Ma, Xue-Qing Gao, Ai-Bing Chen, Dao-Jin Zhou, Xiao-Ming Sun

Journal of Electrochemistry

Active and durable electrocatalysts for methanol oxidation reaction are of critical importance to the commercial viability of direct methanol fuel cell, which has already attracted growing popularities. However, current methanol oxidation electrocatalysts fall far short of expectations and suffer from excessive use of noble metal, mediocre activity, and rapid decay. Here we report the Pt anchored on NiFe-LDHs surface hybrid for stable methanol oxidation in alkaline media. Based on the high intrinsic methanol oxidation activity of Pt nanoparticles, the substrates NiFe-LDHs further enhanced anti-poisoning ability and maintained unaffected stability after 200,000 s cycle test compared to commercial Pt/C catalyst. The …

Recent Advances In Exploring Highly Active & Durable Pgm-Free Oxygen Reduction Catalysts, Yuan Li, Miao-Ying Chen, Bang-An Lu, Jia-Nan Zhang

Journal of Electrochemistry

In order to reduce the considerable usage of expensive but scarce platinum at the cathode in proton exchange membrane fuel cells (PEMFCs), it is necessary to pursue alternatives to platinum. The most promising platinum group metal (PGM)-free catalysts for oxygen reduction reaction (ORR) are atomically dispersed, and nitrogen-coordinated metal site catalysts denoted as M-N-C (M = Fe, Co, or Mn, etc.). Over the last few decades, there have been great advances in these catalysts with high ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the stability of these highly active Fe-N-C catalysts under practical fuel …

Electrochemical Oxidation Of Ethylene On Palladium Electrode, Wei-Xing Wu, Ying Wang

Journal of Electrochemistry

The electrochemical oxidation of C₂H₄ is attracting increasing attention due to its vast potential market. The current electrochemical methods rely on the use of redox mediators, which may produce corrosive intermediates, while direct oxidation is still limited by its low activity and selectivity. Herein, we conducted electrochemical studies to obtain mechanistic insights into the benchmark Pd catalyst. The generated Pd(II) could be the active site for C₂H₄ oxidation. By designing the pulse sequence, we found the ratio of strongly and weakly adsorbed C₂H₄ on Pd to be 0.3:1. The result we …

Supperlattice-Like Structure: Ordered Mass Transfer Endowing High Quality Output Of Fuel Cell, Jian Wang, Wen-Hui Xuan, Qian He, Jing-Xia Jiang, Yuan-Yuan Zhou, Yao Nie, Qiang Liao, Min-Hua Shao, Wei Ding, Zi-Dong Wei

Journal of Electrochemistry

The current or voltage fluctuation in fuel cell operation is harmful to the fuel cell system and power application equipment. Here, we report a technique to eliminate such a fluctuation by the aid of new type of catalysts, superlattice-like mesoporous PtCo catalysts. The current fluctuation in fuel cells catalyzed by two invented catalysts are fixed at as low as 25 mA·cm⁻² with a power of 0.75 W·cm⁻² or 120 mA·cm⁻² with a power of 1.01 W·cm⁻², and no noticeable current decay was detected over 100 h. By contrast, a …

Preface To Special Issue: Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Influence Of Synthesis Conditions On The Physicochemical And Electrocatalytic Properties Of Non-Stoichiometric Ba2sr2la2ti4o12 Perovskites, Ofeliya Kostadinova, Iliyan Popov, Simeon M. Stankov, Hristo Kolev, Tamara Petkov

Karbala International Journal of Modern Science

Present work studies the influence of the pretreatment milling media (deionized water (BLTOS-H) and isopropanol (BLTOS-i)) on the surface characteristics, structure, chemical composition and catalytic activity of non-stoichiometric Ba2Sr2La2Ti4O12 perovskites. The IR spectroscopy and XRD analyses shows a difference in the structure and phase composition of the two materials. X-ray photoelectron spectroscopy detects a Ba2+- and La3+-enriched and Sr2+-depleted surface. The BLTOS-i sample appears to exhibit higher specific surface area (SSA) and pore volume in comparison to BLTOS-H. The electrochemical tests showed that BLTOS-H sample have similar behavior to platinum at current densi-ties up to 10 mA cm-2, while BLTOS-i …

A Process Intensification Approach To Improve Volatile Fatty Acids Production, Extraction, And Valorization, Can Liu

Theses and Dissertations--Biosystems and Agricultural Engineering

Anaerobic digestion (AD) is a widely used biowaste conversion method. Recent studies have explored arrested methanogenesis as an alternative approach to leverage existing AD facilities and produce volatile fatty acids (VFAs) instead of biogas. VFAs have been recognized as precursors for a range of value-added chemicals and bioproducts. Arrested methanogenesis involves inducing acidic fermentation by halting the AD process before methanogenesis. It has been found that higher organic loading and thermophilic conditions enhance VFA accumulation and stabilize the acidic fermentation (AF) system.

Brewer's spent grain (BSG), a significant by-product of the brewing industry, was employed as the feedstock for VFA …

Methyl Isobutyrate Production Via Hydrogenation Of Methyl Methacrylate Derived From Pyrolysis Of Acrylic Plastic Waste, Ramzi Nasser Ahmed Saif

Chulalongkorn University Theses and Dissertations (Chula ETD)

According to zero waste and upcycling policy, this work aims to utilize waste polymethyl methacrylate (PMMA) to methyl isobutyrate (MIB) via hydrogenation over nickel (Ni) based catalysts supported on commercial zeolites: HY, H-Beta-27 (SiO2/Al2O3 = 27 by mole), H-Beta-40 (SiO2/Al2O3 = 40 by mole) and H-ZSM-5. The appropriate catalyst support was first screen by using MMA monomer as the substrate for hydrogenation. Under 30 bar initial H2 pressure (PH2) at 250 °C for 3 h, Ni/H-Beta-27 catalyst effectively promoted hydrogenation to achieve 85% MMA conversion with 56.2 wt% MIB yield because of its larger external surface area and pore size. …

Running Shoe Pedometer, Benjamin Kasper

Williams Honors College, Honors Research Projects

Running shoe pedometer aims to solve the issue of worn out running shoes. It can be difficult to know just how many miles you have run in your shoes and when a new pair is needed. Running in old shoes and worn out shoes is heavily linked to injury. My proposed project is a device that is powered by the compressive forces on the shoes soles that counts the number of steps the wearer takes using a microcontroller. Then, when the shoe reaches milestone that indicate it has been used 75% 90% and 100% of its expected life, it will …

Applying Thermal And Microwave Heating For Natural Gas Conversion To Value-Added Chemicals Over Zeolite-Supported Catalysts, Ashley Marie Caiola

Graduate Theses, Dissertations, and Problem Reports (ETD)

The world’s demand for natural gas has been consistently growing over the past few decades. Natural gas is considered a potential alternative to oil and coal because of its ability to burn cleaner. Although not completely emission-free, it has dominated the energy industry by providing a continuous supply of cheap fuel. Currently, natural gas makes up 41% of North American energy production. The conversion of natural gas to value-added chemicals typically involves the indirect production of synthesis gas (syngas) as an intermediate before the production of the desired product. Steam reforming and partial oxidation are two of the most common …

Level And Temperature Controlled Vessel, Cameron Macesich

Williams Honors College, Honors Research Projects

Using two Arduino microcontrollers, level and temperature Proportional-Integral control systems for a continuously stirred tank reactor were designed and configured. Open-loop step tests were performed and fitted with First Order Plus Time Delay responses so that controller tuning parameters could be analytically derived. The effectiveness of the designed systems was evaluated by monitoring the response of closed-loop setpoint changes.

Understanding The Kinetics And Mechanisms Of The Desired And Undesired Reactions During Electrochemical Hydrogenation And Hydrogenolysis Of Furfural On Copper In Acidic Media, Andrew S. May

Dissertations and Theses

The decarbonization of the chemical industry would have an immense impact on lowering greenhouse gas emissions and assisting in mitigating global warming. To achieve this there is a growing interest in implementing renewable feedstocks like biomass and coupling of chemical processes with renewable energy. Furfural is a biomass derived species that has been identified as a platform molecule. Electrochemical processes are more easily coupled with renewable electricity and can be used to valorize biomass derived species such as furfural. The installation of electrochemical processes is hindered by a smaller knowledge base compared to thermochemical processes. This dissertation investigates the electrochemical …

Ambient Ammonia Synthesis Via Microwave-Catalytic Materials And Plasma Chemistry, Siobhan Brown

Graduate Theses, Dissertations, and Problem Reports (ETD)

Ammonia is critical to supporting human life on earth because of its use as fertilizer. The Haber-Bosch process to produce ammonia has been practiced for over 100 years. This process operates at high pressure and temperature to overcome the thermodynamic and kinetic limitations of the ammonia synthesis reaction thus researchers have tried to overcome it for decades. At present this process represents 1% of global energy usage and 2.5% of global CO₂ emissions. The proposed chemical looping ammonia synthesis approach seeks to reduce the environmental impact of this critical process and to elucidate microwave-catalytic principles.

This research aims to …

Microwave-Assisted Ammonia Synthesis Over Cs-Ru/Ceo2 Catalyst, Alazar Kesete Araia

Graduate Theses, Dissertations, and Problem Reports (ETD)

Ammonia synthesis is one of the greatest innovations of the 20^th century with extensive applications from fertilizers to intermediates for nitrogen-containing chemicals and pharmaceuticals. Annually, more than 242 million tons of ammonia is produced globally, supporting approximately 27% of the world’s population. One of the fast-growing applications for ammonia is as H₂ energy carrier due to its high energy storage capacity, considered to be a decarbonized energy source. The low volumetric energy density and incompressibility makes Hydrogen a non-preferable energy carrier; an alternative carrier becomes a requirement. Ammonia possesses unique property as an energy-dense carrier to store and …

Carbon Dioxide And Steam Gasification Of Biochar: A Study On Mitigating Greenhouse Gas Emissions And Producing Syngas For Downline Synthesis Of Renewable Hydrocarbon Fuel, Parth Patel

College of Graduate Studies: Theses & Dissertations

This research explores the potential of mitigating CO₂ emissions from fossil fuel consumption and providing an alternative renewable source of energy by gasifying biochar with carbon dioxide (CO₂) and steam (H₂O). The utilization of captured carbon dioxide and wastewater in industrial sectors is considered to further contribute to the advancements in energy-efficient and low-emission technological solutions. This research evaluated the performance and kinetic parameters of biochar gasification through CO₂ and H₂O gasification using a stainless-steel fixed bed reactor. The operating parameters including biochar mass, reactor temperature, and inlet flow rate were varied. …

Investigation Of Additives And Ingredients Of Bio-Resin For Visible Wavelength Laser-Induced Polymerization, Patrick Riggs

College of Graduate Studies: Theses & Dissertations

Optical 3D printing is a branch of Additive manufacturing (AM) that utilizes low-waste production leading to efficient and rapid prototyping. Currently, this method of AM is associated with mainly petroleum-based resins. Bio-resin polymerization is an emerging research area for finding replacements for petroleum-based resins, but curing the resin with laser energy is not normally a practical use case. Current optical 3D printing uses lasers to cure liquid resins to form solid 3D objects in a layer-by-layer process which is time consuming, defect prone, and a leading limiting factor for high volume production; so, finding a way to incorporate bio-resin into …