Chemical Engineering Commons^™

Nanoparticle Formation In The Flame Synthesis Of Multicomponent Nanostructured Materials For Clean Energy Applications, Jiaxi Fang

McKelvey School of Engineering Graduate Student Theses & Dissertations

This dissertation studies the initial stages of particle formation during the combustion synthesis of multicomponent nanomaterials. Combustion is commonly used for the production of nanomaterials at industrial scales and has advantages of high production rates, low waste generation, and scalability. However, there are limitations in being able to apply this synthesis approach to more advanced multicomponent systems. Gas to particle conversion in flames occurs through precursor decomposition, collisional growth, coagulation, condensation, and sintering. There is a fundamental gap in knowledge on the initial stages of particle formation in flames below 2nm due to measurement difficulties and instrumentation limitations. Using a …

Crumpled Graphene Oxide: Aerosol Synthesis And Environmental Applications, Yi Jiang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Environmental technologies, such as for water treatment, have advanced significantly due to the rapid expansion and application of nanoscale material science and engineering. In particular, two-dimensional graphene oxide (GO), has demonstrated considerable potential for advancing and even revolutionizing some of these technologies, such as engineered photocatalysts and membranes. To realize such potential, an industrially scalable process is needed to produce monomeric and aggregation-resistant GO nanostructures/composites, in addition to new knowledge of material properties, behavior, and performance within an environmental context.

Research presented in this thesis addresses both scientific and engineering gaps through the development of a simple, yet robust aerosol-based …

Application Of Voltammetry For Electroanalytical Measurement Of Concentrations In Lacl3-Mgcl2 Mixtures In Eutectic Licl-Kcl, Zhonghang Wang, Devin Rappleye, C S. Yang, Michael Simpson

Faculty Publications

For electroanalytical measurement of molten chloride salts, various voltammetry methods have been used on mixtures of MgCl₂ and LaCl₃ in eutectic LiCl-KCl. These salt mixtures are of primary interest to spent nuclear fuel electrorefining systems. MgCl₂ is used as a surrogate for PuCl₃, while LaCl₃ represents rare earth fission product salts. Cyclic voltammetry scans with these salt mixtures exhibited extra peaks, presumably due to underpotential deposition of La(III) ions onto Mg. Quantitatively, the current contribution from each peak was best determined using normal pulse voltammetry and fit to the Cottrell equation. This yielded linear …

Development And Characterization Of Oxygen Sensitive Microbial Biosensors, Jonathan Lee

Rose-Hulman Undergraduate Research Publications

Microbial biosensors are useful in detecting suboptimal conditions in a bioreactor. This detection can help in development of improved mixing methods to reduce the occurrence of these conditions. In this research, the activities of 3 promoters known to have activity under anaerobic conditions, the gadB promoter, an FNR protein activated promoter, and the pfl promoter, were tested for activity under anaerobic conditions by connecting them to a green fluorescent protein (GFP) gene. Using two types of media, Luria-Bertani (LB) and Wilms-Reuss media, the activity of these promoters under aerobic and anaerobic conditions were tested. Results indicate that while the FNR …

Amine-Thiol Solution Route Method For Fabricating Cdxzn1-Xs Thin Film Solar Cells, Preston D. Fernandez, Xianyi Hu, Carol Handwerker, Rakesh Agrawal

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cadmium zinc sulfide, CdZnS, is a promising material for the buffer layer of thin film solar cells because the alloy is considerably more cost effective and more optimizable than pure cadmium sulfide, CdS, in terms of band gap. The current fabrication methods of the buffer layer often require expensive equipment or produce undesirable impurities in the alloy. This study investigates a cost effective and scalable solution route method to synthesize the CdZnS buffer layer. Molecular precursors of CdZnS were dissolved in varying molecular ratios of cadmium and zinc in a mixture of hexylamine and propanethiol. The resulting alloys produced were …

Hydrophobic Zeolites For Applications In Adsorption And Catalysis, Zige Huang, Michael Cordon, Rajamani Gounder

The Summer Undergraduate Research Fellowship (SURF) Symposium

Lewis acidic zeolites such as Sn-Beta are commonly studied for use as selective catalysts for glucose isomerization to fructose in liquid water. Glucose to fructose isomerization is a critical reaction for lignocellulosic biomass upgrading, which converts abundant and renewable feedstocks into commercially desirable fuels and chemicals.

Industrial applications require catalysts that maintain optimal reactivity over long time scales, yet at typical reaction temperatures, Lewis acidic Beta zeolites are known to deactivate in liquid water through poorly understood mechanisms. Recent work in our group has shown that interactions between water and Sn-Beta zeolites can cause leaching of active Sn sites from …

Exploring The Effects Of Aromatic Molecules In Chemical Enhanced Oil Recovery, Jacob M. Crain, Cliff Johnston, Rituraj Borgohain

The Summer Undergraduate Research Fellowship (SURF) Symposium

Chemical enhanced oil recovery (cEOR) methods are being used as a viable contributor to the world’s growing energy demands. Due to the complex chemical composition of crude oil, attempting to optimize the surfactant concentration and salinity of formulations is done empirically. This process can be very time intensive due to the wide variety of surfactant structures available for cEOR. Surfactant selection is typically done by matching the average chain length of the oil with that of the surfactant. In this study, we are trying to understand how aromatic structures present in Illinois Basin crude oil interact with surfactants. This will …

Continuous Ligand-Assisted Elution Chromatography Applied To Separation Of Rare Earth Elements, Jeremy A. Weinstock, David M. Harvey, N.-H. Linda Wang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Rare earth elements (REEs) are metals used to make many valuable products such as magnets and electronics. Following their extraction from larger materials, REEs are to be separated into their individual components as high purity is required for product manufacture. Purification is very difficult because most (15/17) of the REEs are lanthanides (Ln’s) and Ln ions have the same valence and similar atomic radii. The current industrial process for purifying REEs involves using toxic solvents to perform a series of liquid-liquid extractions. Ling and Wang (2015) proposed a ligand-assisted batch chromatography process to purify Ln’s. The latter approach is a …

Quantification And Characterization Of Aluminum Distributions In Commercial Beta And Mordenite Zeolites By Cobalt Exchange, Rebecca L. Reitzel, Claire T. Nimlos, Rajamani Gounder

The Summer Undergraduate Research Fellowship (SURF) Symposium

The aluminum distribution throughout the zeolite framework determines the structural, ion-exchange and catalytic properties of the zeolite. Several methods have been proposed to control the Al distribution, but in order to accurately assess these methods a procedure is needed to quantify Al distribution in various zeolite frameworks. Co²⁺ ions exchange onto the zeolite framework at Al pairs, and atomic absorbance spectroscopy (AAS) can be used to quantify the number of exchanged Co²⁺ ions and, in turn, the overall number of Al pairs. Each framework exhibits differences in pore size and channel configuration which affect the equilibrium conditions needed …

Production Of Porous Alginate Substrates Via Membrane Emulsification For Pharmaceutical Applications, Genesis D. Correa-Rivera, David A. Acevedo, Zoltan K. Nagy

The Summer Undergraduate Research Fellowship (SURF) Symposium

The Food and Drug Administration (FDA) released in 2013 a report that established the pharmaceuticals current good manufacturing practices for the 21^st century. This report encourages the creation of new technology in the pharmaceutical industry. Therefore, this research aims to develop a reliable method to produce porous polymers particles to be used in a novel continuous crystallization in porous substrate. The aim of the current work is to create porous polymer microspheres with uniform particle size distribution using a commercially available membrane emulsification system. In the present study, the emulsification was made using a dispersed phase composed of miglyol …

Effect Of Conveying And Distributive Mixing Elements On Breakage Phenomenon In Twin Screw Granulation, Jiayu Li, Shankali U Pradhan, Carl Wassgren

The Summer Undergraduate Research Fellowship (SURF) Symposium

Twin screw wet granulation (TSG) is gaining more attention and becoming an important process in the pharmaceutical industry. The process is widely implemented because of its flexibility, short residence time, and small equipment footprint. Past studies have shown that screw elements can have a significant impact on the performance of the TSG process. In addition, these studies identified that breakage of wet mass is a significant step in the process. Currently there is no literature that focuses on the effect of each screw element on the breakage process. In this work, experiments have been designed to isolate the breakage process …

Pt-Cu Catalysts For Catalytic Dehydrogenation Of Alkanes For Energy Production, Zixue Ma, Zhenwei Wu, Jeffrey T. Miller

The Summer Undergraduate Research Fellowship (SURF) Symposium

More active, selective and stable catalysts are in demand to increase the yields of olefins production from light alkane dehydrogenation. Cu was reported to promote Pt catalysts and Pt-Cu catalysts has been shown to achieve increased olefin selectivity and decreased deactivation rate. Pt-Cu catalysts with different Pt:Cu molar ratios may have different crystal structure and performance. This study seeks to understand of the promotion effect of Cu on Pt alkane dehydrogenation catalysts. Four different Pt-Cu catalysts with different atomic ratios were prepared and tested for propane dehydrogenation at 550℃. Synchrotron in situ X-ray diffraction and X-ray absorption spectroscopy are used …

A Highly Efficient Dual Rotating Disks Photocatalytic Fuel Cell With Wedged Surface Tio2 Nanopore Anode And Hemoglobin Film Cathode, Chen Yang, Yi He, Kan Li, Diwen Ying, Ye Yao, Tiantian Tang, Yalin Wang, Jinping Jia

Publications and Research

In this study, a dual rotating-disk photocatalytic fuel cell using TiO₂ on Ti plate with a wedged surface as the anode and hemoglobin (Hb) on graphite as the cathode was investigated and found to show excellent performance of simultaneous organic pollutant degradation and electricity generation. This study is based on a well-developed photocatalytic fuel cell equipped with dual rotating disks for wastewater treatment that we developed previously, and the innovation of this new device is using a hemoglobin on graphite cathode for in situ hydrogen peroxide (H₂O₂) generation. The result proved with confidence that H …

Fast Diffusion Of Silver In Tio2 Nanotube Arrays, Wanggang Zhang, Yiming Liu, Diaoyu Zhou, Hui Wang, Wei Liang, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Using magnetron sputtering and heat treatment, Ag@TiO₂ nanotubes are prepared. The effects of heat-treatment temperature and heating time on the evolution of Ag nanofilms on the surface of TiO₂ nanotubes and microstructure of Ag nanofilms are investigated by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Ag atoms migrate mainly on the outmost surface of the TiO₂ nanotubes, and fast diffusion of Ag atoms is observed. The diffusivity for the diffusion of Ag atoms on the outmost surface of the TiO₂ nanotubes at 400 °C is 6.87 × 10⁻¹⁸ m²/s, …

Sugarcane Bagasse As A Carrier For The Immobilization Of Saccharomyces Cerevisiaein Bioethanol Production, Sita Heris Anita, Wibowo Mangunwardoyo, Yopi Yopi

Makara Journal of Technology

Sugarcane bagasse was used as a carrier to immobilize Saccharomyces cerevisiae in bioethanol production. This research aims to study the potential use of sugarcane bagasse as an alternative carrier for cell immobilization and improvement in the production process of cell immobilization in bagasse. The results showed that the physical characteristics of sugarcane bagasse as a carrier were water content (7.77 ± 0.35%), water retention (4.80 ± 0.44 g/g), water absorption index (8.58 ± 0.22 g/g), and lignin content (24.40 ± 1.52 %). Determination of cell retention was performed in an inoculum volume of 50 mL yeast suspension with various carrier …

Study On Oil Palm Fresh Fruit Bunch Bruise In Harvesting And Transportation To Quality, Andreas Wahyu Krisdiarto, Lilik Sutiarso

Makara Journal of Technology

There are losses of production due to oil palm field’s material handling. Activities that may raise the losses are harvesting and transportation, which may cause bruise and damage to fruit. This research was aimed to learn the bruise of fresh fruit bunch (FFB) phenomenon in harvesting and transportation. Method used in this research was measuring the bruise area resulted by FFB falling when harvested, loading (throwing up) FFB to truck bin, and transporting using truck. These data, coupled with weight of bruised fruit, were calculated to get FFB bruise index. Each FFB bruise index is related to potential free fatty …

Automatic Arrhythmia Beat Detection: Algorithm, System, And Implementation, Wisnu Jatmiko, I Md. Agus Setiawan, Muhammad Ali Akbar, Muhammad Eka Suryana, Yulistiyan Wardhana, Muhammad Febrian Rachmadi

Makara Journal of Technology

Cardiac disease is one of the major causes of death in the world. Early diagnose of the symptoms depends on abnormality on heart beat pattern, known as Arrhythmia. A novel fuzzy neuro generalized learning vector quantization for automatic Arrhythmia heart beat classification is proposed. The algorithm is an extension from the GLVQ algorithm that employs a fuzzy logic concept as the discriminant function in order to develop a robust algorithm and improve the classification performance. The algorithm is tested against MIT-BIH arrhythmia database to measure the performance. Based on the experiment result, FN-GLVQ is able to increase the accuracy of …

Optimization Of Electricity Generation Schemes In The Java-Bali Grid System With Co2 Reduction Consideration, Farizal Farizal, Wenty Eka Septia, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

This research considers the problem of reducing CO2 emissions from the Java-Bali power grid system that consists of a variety of power-generating plants: coal-fired, natural gas, oil, and renewable energy (PV, geothermal, hydroelectric, wind, and landfill gas). The problem is formulated as linear programming and solved using LINGO 10. The model was developed for a nation to meet a specified CO2 emission target. Two carbon dioxide mitigation options are considered in this study, i.e. fuel balancing and fuel switching. In order to reduce the CO2 emissions by 26% in 2021, State Electric Supply Company (PLN) has to generate up to …

The Knowledge-Based Analysis On Medium Resolution Images Of Remote Sensing To Extraction Information Land Use Type Scs-Cn, The Case Study On Grompol Watershed, Puguh Dwi Raharjo, Totok Gunawan, Mohammad Pramono Hadi

Makara Journal of Technology

Remote sensing imagery Landsat-8 is one image that has a good temporal resolution; in addition to the availability of data, this image can be obtained free of charge. Land cover type SCS-CN is part of a unit of land that affects runoff. The use of medium resolution imagery in reducing the SCS-CN land use type is considered relatively difficult, and it yields less good accuracy. Limitations on multispectral classification only rely on facts derived from spectral reflection, so that the two data are the same since different characteristic results are not so good. This study aims to determine the accuracy …

The Effect Of Irradiation Of Fe And Ar Ion On The Surface Morphology Of Diamond Thin Film Related To The Magnetoresistance Property, Salim Mustofa, Setyo Purwanto, Kenji Mishima

Makara Journal of Technology

The irradiation of Fe and Ar ion was applied on the surface of diamond/Si thin film to know its effect on the morphology of thin film.The magnetoresistance property was also studied. Ion irradiation treatment using Fe ion followed by argon ion at the energy of 70keV and a dose of 1 x 1015 ion/cm2 have been conducted on the surface of two types of thin film, diamond/Si (111) and diamond/Si (100). Both thin films were made by using a CVD method, and the thickness of the thin film is 1000-nm. From simulations using the software called Stopping and Range of …

Use Of Green Mussel Shell As A Desulfurizer In The Blending Of Low Rank Coal-Biomass Briquette Combustion, Mahidin Mahidin, Asri Gani, M. Reza Hani, Muhammad Syukur, Hamdani Hamdani, Khairil Khairil, Samsul Rizal, Abdul Hadi, T.M.I. Mahlia

Makara Journal of Technology

Calcium oxide-based material is available abundantly and naturally. A potential resource of that material comes from marine mollusk shell such as clams, scallops, mussels, oysters, winkles and nerites. The CaO-based material has exhibited a good performance as the desulfurizer or adsorbent in coal combustion in order to reduce SO2 emission. In this study, pulverized green mussel shell, without calcination, was utilized as the desulfurizer in the briquette produced from a mixture of low rank coal and palm kernel shell (PKS), also known as bio-briquette. The ratio of coal to PKS in the briquette was 90:10 (wt/wt). The influence of green …

Apparent Porosity And Compressive Strength Of Heat-Treated Clay/Iron Sand/Rice Husk Ash Composites Over A Range Of Sintering Temperatures, M. Nizar Machmud, Zulkarnain Jalil, Mochammad Afifuddin

Makara Journal of Technology

Novel composites of clay/iron sand/rice husk ash (RHA) have been developed. Electric furnace was used to perform heat treatment on the composites to study the effect of sintering temperature on their apparent porosity and compressive strength. Two types of RHA with different bulk density were prepared to gain an understanding of the influence of apparent porosity on compressive strength of the heat-treated composites over a range of sintering temperatures. Heattreated composites, made of clay/iron sand and clay/RHA, were also prepared as a referenced material. X-ray diffraction (XRD) analysis was further performed to comprehensively discuss the role of iron sand on …

Lithium-Ion Batteries, Dean R. Carreon Romero

BYU Research Development Office Research Networking Conference

Electrochemical systems are fundamental to numerous applications, including batteries, fuel cells, and electrolysis. Accurate modeling of these systems is essential for improving their efficiency, performance, and longevity. This research focuses on the process of modeling electrochemical systems and conducting experiments to measure the local electronic and ionic conductivity of electrodes.

Adsorption Kinetics Of Bovine Serum Albumin To Strong Anion Exchange Adsorbents: Application Of The Pore Diffusion Model To Resins And Membranes, Sarah Catherine Jensen

Graduate Theses - Chemical Engineering

The replacement of traditional bead-based chromatography by membranes has gained recent interest in the bioseparations industry. However, membranes have drawbacks such as lower binding capacity that make them unrealistic for some applications. The goal of this work is to compare the adsorption kinetics of anion exchange bead-based resin and membranes both on a theoretical modeling level and experimental level. Bovine serum albumin (BSA) was adsorbed to Q Sepharose FastFlow resin and Sartobind Q membrane to obtain adsorption equilibrium characteristics and kinetic data. A numerical solution was used to fit the pore diffusion model to the data and estimate a pore …

Biomedical Engineering, William Pitt

BYU Research Development Office Research Networking Conference

Polymeric biomedical materials and drug delivery, with recent emphasis on blood sepsis diagnostics. Today I am looking for collaboration in mathematical modeling of instabilities in sheared 2 phase flow.

Development Of A New Multimodal Membrane Adsorber And Its Application In Chromatographic Bioseparations, Juan Wang

All Dissertations

This dissertation presents work on the design and synthesis of a new membrane chromatography material, the description of its protein binding behavior using a thermodynamic adsorption isotherm model, and the application of the new membrane material in biologics downstream recovery and purification processes. As protein titers continue to increase dramatically in upstream biomanufacturing, innovations in downstream purification are not keeping pace, resulting in manufacturing capacity constraints and high production costs. Chromatography is the key unit operation used in several steps of the downstream purification platform. Traditional resin bead chromatography, while effective and reliable for isolation and purification of proteins, limits …

Enzymatic Liquefaction Of Untreated Corn Stover, Neal N. Hengge

Open Access Theses

There is an ever increasing need for renewable alternatives to fossil fuels derived from petroleum. This makes feedstocks in the form of lignocellulosic biomass attractive substrates for the production of ethanol and value added chemicals. However, the economics of converting lignocellulosic materials involve high processing costs attributed with pretreatment of the biomass and the use of enzymes for saccharification. Corn stover was obtained for the examination of an upstream processing step to transform the material into a pumpable slurry for subsequent pretreatment and saccharification. Biomass liquefaction was carried out using the enzyme Depol 692L (Biocatalysts, Wales, UK) at 50°C with …

Enhancing Silymarin Fractionation Via Molecular Modeling Using The Conductor-Like Screening Model For Real Solvents, Emma C. Brace

Open Access Theses

The market for bio-based products from plant sources is on the rise. There is a global challenge to implement environmentally clean practices for the production of fuels and pharmaceuticals from sustainable resources. A significant hurdle for discovery of comparable plant-derived products is the extensive volume of trial-and-error experimentation required. To alleviate the experimental burden, a quantum mechanics based molecular modeling approach known as the COnductor-like Screening Model for Real Solvents (COSMO-RS) was used to predict the best biphasic solvent system to purify silymarins from an aqueous mixture. Silymarins are a class of flavonolignans present in milk thistle ( Silybum marianum …

Enabling A Sustainable Economy Through Energy Systems Modeling: Solar-Centric, Efficient, Integrated And Continuous Process Synthesis And Optimization, Emre Gencer

Open Access Dissertations

The expected increase in food, energy and water demand due to increase in population and change in consumption habits in conjunction with diminishing fossil fuel reserves and increasing greenhouse gas emissions urge the development and implementation of alternative energy conversion techniques using renewable energy for a sustainable economy. Among renewable energy sources, solar energy is prominent due to its abundance. A sustainable economy can be created by producing building blocks foundational to meeting all basic human needs of daily existence. However, intermittencies and limitations on land area dedicated to harness solar energy are the major obstacles on widespread implementation of …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.